If a person wanted to save weight on cable ends, consider 'bird caging' the eyelets. Ironically, it's typically only used where you need maximum strength from the cable end. Amazing build, I just stumbled across it and I'm enjoying your videos. You clearly have the patience of a saint.
I think there is a risk in how the tail rotor pitch control rod axis is fixed. Two screws are the only way to fix the red rod axle from the wire to the control bar (timestamp 17; 24) During flight, this screw may loosen and cause loss of tail rotor pitch control. It is recommended to fix this shaft with a dowel pin, etc., instead of screwing it.
Excellent observation. The bolt threads themselves cause possible fracture points and should not be used for like this. a Dowel pin is the way to go. :)
An intricate maintenance schedule needs to be written with every single piece installed as there are many areas that will fall prey to metal fatigue. Adequate and correct lubrication is another consideration.
Вы сударь, слишком сильно озабочены мелочами. Я уверен, после сборки будут ходовые испытания с выявлением слабых мест креплений, осей, точек крепления.
Amigo. Revise as fixações o cabo de aço no rotor de calda. Coloque chavetas, em vez de parafusos. Certifique-se que os cabos de aço não sairão das roldanas com a vibração das laminas. Coloque algo para que esses cabos de aço não saiam do alojamento. Você está de parabéns!
Hello, my name is Haylson, I'm from São Paulo Brazil, I watched all your videos from the first assembly to the end, wonderful, I love helicopters, I loved their mechanics, exceptional, a classy job, it's worth watching your videos this way assembly, big hug and congratulations, I'm 69 years old.
The system is as strong as the weakest part. That 2 small screws that engage the shaft would take all the load?? They will end up breaking maybe. And that beating will take side or axial load, not perpendicular load. Wouldn't be best using 2 side load bearing, one for each direction?? I like your videos. Thanks for sharing
Дружище, сделай стопор на всех винтах на управлении и добавь ограничители на тросы что бы не соскочили, это очень ответственный узел так как от него зависит твоя жизнь
For it to Fail, all that needs to happen is 2 screws holding a 5mm shaft let go. The Nice Red bit and small pin shaft needs something like a 10mm square shaft with fixing screws ... Just commenting ...
My gosh you're almost done 😮 It feels like I've been watching this build forever! Please upload the last build video before you test fly it 😂 Why do you have an Australian flag on the wall? Does it symbolise you are crazy enough to fly it? ❤ Hahaha... Excellent work.. Greetings from Melbourne!
The name on your toolbox is the same as a very good but maybe forgotten band! Just one of their tunes is, radio activity . First time I heard them was about 1980. Check them out.
Bro you should use high quality insulated cable.... The one which we saw in cars clucth and hand brake.... These set is not good... Cables may wobble when engine starts and due to vibration cable may jump off from pulleys
I would add a guard over the cables so that the cables cannot jump off the pullies . If they did jump off you would loose all control of the tail rotor..
I Agree with Iron c ly---the fixi g of the Red Bit is a bit weak. I fly model hellicopters, and was amazed at the force needed to control the pitch on a model. That really is the weak link in the system, and you have no control if it does slip
Please do not kill yourself. Aluminium on aluminium bearings ar NOT good and when using the bearinghousing as you do you are prone to have cracks in the border between housing and pegs, you did not machine a radius on it which is NO good. Take your time and finish your machine a safe way. Good luck building.
I was thinking, the bearing main load would be axial load and its not meant to take this axial or side load. Wouldn't be better to use 2 side load bearings, one for each load direction?? The bearing he used is for perpendicular load. And that 2 screws that fix the axis are the weakest point in the system and definitely will fail.
Mmmmmmm, muy inseguro ese sistema para mover el paso del rotor de cola,un eje tan pequeño precionado por solo dos tornillos, sin espina, sin chaveta u otro sistema de fijación, es muy peligroso, teniendo en cuenta la importancia del rotor de cola.
All this is great...BUT who puts dural on dural...all rollers without bearings.... dust and sand will get there...and this is for sure, there are such scoring, such wear will be and then backlashes will be....And the hook of the stopper is also made of dural... is not afraid that it may simply straighten out - bend from the loads, and what is made of steel sheet cannot be bent.And another thing...the back edge of the blade I never noticed...he didn't weld it on...he left it all on foam to hold on...!!! ?????? I would definitely not do that.... it's not right !!! 👎👎👎
Hallo Leute. Alles klar..? Hm.. Die Klemmung per 2-Schrauben auf den Pin wäre mir zu unsicher! Besser wäre doch Geschlitzt und Verschaubte radialklemmung..? Grüsse aus'm Saarland
Hallo... Ja die Klemmung ist mir auch zu unsicher (wenn auch auf den Bauplänen so vorgesehen). Ich werde ein update machen wahrscheinlich mit einer radialen Verklemmung. Grüsse ins Saarland
این ماشین دوست داشتنی لحظه به لحظه در حال تکامل و زیباتر شدن پیش میرود. قوانین کشور من بخاطر تحریم های دولتی اجازه نمیدهد تا من بتوانم اشتراک کانال شما را خریداری کنم تا به تمام قسمت های ساخت ماشین شما دست پیدا کنم. هرچند که دعوا بین دولت ها هست و ما مردم عادی تقصیر نداریم! ای کاش شما راهکار و فکری بحال این دسته از افراد میکردید، شاید در کانالتان تعداد کمی با شرایط من باشند. لطفا کمک کنید تا منم بتوانم به تمام قسمت های کانال دسترسی داشته باشم. متشکرم
Please,, wipe your vise surface parallels before you place parts on them. The accrued intolerance will come back and bit you in the a$$. Very sloppy machining, but very determined methodology. I've worked building helicopters at Sikorsky Aircraft for 10 years. Such sloppy machining would have got you fired. You are building quite a nice helicopter there. It would be sad to see something bad happen. Also, a dowel should be used instead of a bolt. Dowels are much stronger, and bolts can fracture at the threads (17:24). They are made for tension, not shear force. Dowels are what you need for shear force.
See the Full Build Documentation Movie here: ua-cam.com/video/pkIl0FS-kwc/v-deo.html
If a person wanted to save weight on cable ends, consider 'bird caging' the eyelets. Ironically, it's typically only used where you need maximum strength from the cable end. Amazing build, I just stumbled across it and I'm enjoying your videos. You clearly have the patience of a saint.
Ese eje y manivela de color rojo es muy precario, miro u a y otra vez el vídeo y siempre me dan ganas de escribirte para que lo mejores.
I think there is a risk in how the tail rotor pitch control rod axis is fixed.
Two screws are the only way to fix the red rod axle from the wire to the control bar (timestamp 17; 24)
During flight, this screw may loosen and cause loss of tail rotor pitch control.
It is recommended to fix this shaft with a dowel pin, etc., instead of screwing it.
Excellent observation. The bolt threads themselves cause possible fracture points and should not be used for like this. a Dowel pin is the way to go. :)
cotter pin nedeed
An intricate maintenance schedule needs to be written with every single piece installed as there are many areas that will fall prey to metal fatigue. Adequate and correct lubrication is another consideration.
Вы сударь, слишком сильно озабочены мелочами. Я уверен, после сборки будут ходовые испытания с выявлением слабых мест креплений, осей, точек крепления.
friction only seems not safe enough to me
espetacular, imprecionante sua dedicaçao neste projeto, raro de se ver , parabens
I just wait that day you finished the helicopeter....waiting that·~~~amazing man!!
potensial loose on pivot red bell crank, better bellcrank shaft to be grind to get settle on 2 screws, to avoid loose and slip...god job
Amigo. Revise as fixações o cabo de aço no rotor de calda. Coloque chavetas, em vez de parafusos. Certifique-se que os cabos de aço não sairão das roldanas com a vibração das laminas. Coloque algo para que esses cabos de aço não saiam do alojamento. Você está de parabéns!
Hello, my name is Haylson, I'm from São Paulo Brazil, I watched all your videos from the first assembly to the end, wonderful, I love helicopters, I loved their mechanics, exceptional, a classy job, it's worth watching your videos this way assembly, big hug and congratulations, I'm 69 years old.
The system is as strong as the weakest part. That 2 small screws that engage the shaft would take all the load?? They will end up breaking maybe.
And that beating will take side or axial load, not perpendicular load. Wouldn't be best using 2 side load bearing, one for each direction??
I like your videos. Thanks for sharing
Дружище, сделай стопор на всех винтах на управлении и добавь ограничители на тросы что бы не соскочили, это очень ответственный узел так как от него зависит твоя жизнь
Thank you very much for the video. 👍🤗👍🇸🇯
Estou muito ansioso para ver o resultado final !!
Great work god bless you , i really enjoyed watching your video .
I'm koeean and I admire and admire your great skills. And he's the coolest guy ever.
Ansioso para o próximo vídeo.
ESTOY ANSIOSO POR VER TERMINADO EL ULTRALIGERO, VAMOS BROOO, SIGUE ASÍ!!!!
For it to Fail, all that needs to happen is 2 screws holding a 5mm shaft let go.
The Nice Red bit and small pin shaft needs something like a 10mm square shaft with fixing screws ... Just commenting ...
Yes i agree, this design with 2 screws holding the shaft is a weak point. Need to do a update on this....
@@ultralighthelicopter thank you - Safe Flying
estoy ansioso por ver terminar tu ultraligero, mis respetos bro, tu fiel suscriptor te da ánimos :3
Your pitch setting is probably quite close to correct as a steady tail setting is not zero pitch, but whatever is needed to keep the tail steady.
My gosh you're almost done 😮 It feels like I've been watching this build forever! Please upload the last build video before you test fly it 😂 Why do you have an Australian flag on the wall? Does it symbolise you are crazy enough to fly it? ❤ Hahaha... Excellent work.. Greetings from Melbourne!
you do very good work! You're almost done!!!
A fan, 👍 welding skills plus love it 😀 😍 ❤ ♥
👏👏👏👏👏👏👏👏👏👏👏
All parts make a pdf it will be wonderful, keep going we still waiting for the last part to see how it will be flying.
Лучший👍👍👍👍
Awesome work.
The name on your toolbox is the same as a very good but maybe forgotten band! Just one of their tunes is, radio activity . First time I heard them was about 1980. Check them out.
Bro you should use high quality insulated cable.... The one which we saw in cars clucth and hand brake.... These set is not good... Cables may wobble when engine starts and due to vibration cable may jump off from pulleys
Love your Porsche. I just binge watched all the videos in this Series and was wondering if I missed the one on your control panel and all your wiring?
Intelligent man🫡🫡
👍👍👍🔥🔥🔥⚡⚡⚡
I would add a guard over the cables so that the cables cannot jump off the pullies . If they did jump off you would loose all control of the tail rotor..
DEFINITELY
I’m gonna have withdrawals when you finish and over test flight. Guess you’ll have to start something else lol
🤙
Awesome
Good job
Appreciate to You are description
بسیار عالی پرفکت
شایان تقدیر است مهارت شما
I Agree with Iron c ly---the fixi g of the Red Bit is a bit weak. I fly model hellicopters, and was amazed at the force needed to control the pitch on a model. That really is the weak link in the system, and you have no control if it does slip
I have calculated 10% of the torque of the main, i would like what you have found (cause I am just an hobbyst)
Great work ❤
Please do not kill yourself. Aluminium on aluminium bearings ar NOT good and when using the bearinghousing as you do you are prone to have cracks in the border between housing and pegs, you did not machine a radius on it which is NO good. Take your time and finish your machine a safe way. Good luck building.
I was thinking, the bearing main load would be axial load and its not meant to take this axial or side load. Wouldn't be better to use 2 side load bearings, one for each load direction?? The bearing he used is for perpendicular load.
And that 2 screws that fix the axis are the weakest point in the system and definitely will fail.
how do you know what should be thickness of the blades and how big the blades will be.
Hello, I love this field, but I don't know how to start learning.
sanki kuyruk rotoru bitarafa tam dönüyo diger tarafa neredeyse hiç dönmüyormuş gibi kolay gelsin
So uma observação. Você deve colocar travas transversal em todos parafuso 🔩. Porque a vibração é muito
This helicopter hasn't been able to fly a long time.
так рискованно сделать ось!
Она без нагрузки почти.
@@miklemikle-1982 смотря с чем сравнивать. Реально там может быть большое сопротивление отклонению при максимальных углах атаки
Mmmmmmm, muy inseguro ese sistema para mover el paso del rotor de cola,un eje tan pequeño precionado por solo dos tornillos, sin espina, sin chaveta u otro sistema de fijación, es muy peligroso, teniendo en cuenta la importancia del rotor de cola.
No amigo.. mejora ese sistema.
All this is great...BUT who puts dural on dural...all rollers without bearings.... dust and sand will get there...and this is for sure, there are such scoring, such wear will be and then backlashes will be....And the hook of the stopper is also made of dural... is not afraid that it may simply straighten out - bend from the loads, and what is made of steel sheet cannot be bent.And another thing...the back edge of the blade I never noticed...he didn't weld it on...he left it all on foam to hold on...!!! ??????
I would definitely not do that.... it's not right !!! 👎👎👎
fly
Well done work but I have it resting to len
Hallo Leute. Alles klar..?
Hm.. Die Klemmung per 2-Schrauben auf den Pin wäre mir zu unsicher!
Besser wäre doch Geschlitzt und Verschaubte radialklemmung..?
Grüsse aus'm Saarland
Hallo... Ja die Klemmung ist mir auch zu unsicher (wenn auch auf den Bauplänen so vorgesehen). Ich werde ein update machen wahrscheinlich mit einer radialen Verklemmung. Grüsse ins Saarland
I waiting you for update
Kapan terbangnya?, Aku telah lama menunggu!.
این ماشین دوست داشتنی لحظه به لحظه در حال تکامل و زیباتر شدن پیش میرود. قوانین کشور من بخاطر تحریم های دولتی اجازه نمیدهد تا من بتوانم اشتراک کانال شما را خریداری کنم تا به تمام قسمت های ساخت ماشین شما دست پیدا کنم. هرچند که دعوا بین دولت ها هست و ما مردم عادی تقصیر نداریم! ای کاش شما راهکار و فکری بحال این دسته از افراد میکردید، شاید در کانالتان تعداد کمی با شرایط من باشند. لطفا کمک کنید تا منم بتوانم به تمام قسمت های کانال دسترسی داشته باشم. متشکرم
That design has a number of obvious and system critical failure points
I would no fly that aircraft the tail gearbox and especially the tail rotor control is so bad that failure is guaranteed
Please,, wipe your vise surface parallels before you place parts on them. The accrued intolerance will come back and bit you in the a$$. Very sloppy machining, but very determined methodology. I've worked building helicopters at Sikorsky Aircraft for 10 years. Such sloppy machining would have got you fired. You are building quite a nice helicopter there. It would be sad to see something bad happen. Also, a dowel should be used instead of a bolt. Dowels are much stronger, and bolts can fracture at the threads (17:24). They are made for tension, not shear force. Dowels are what you need for shear force.
Are you going to risk your life on a cutoff nail
Per piombare i cavi, serve l’apposita pinza. Nelle carrucole, va messo un cuscinetto.