Thank you for the clear instructions. I had to replace my switch and it only took a couple minutes after seeing how. I was worried that I would run out of gas on my way home last week since the fuel door unlock button is on the same module, but luckily that button worked and I was able to fill the tank.
Hi. My DIM/climate zone is dark and highbeams wont stay on + when i lock the car my orange/hazard lights wont blink. You think this switch could be the problem too?
It's nice to hear you so calm when you're struggling as hell to get that flashright right while still trying to point and film the details in a very tight spot. Nice instructions. Don't you need to disconnect the battery before you replace that switch ?
Hi, no need to undo the battery for this switch unit, it is not part of the canbus network so it won't trigger the SRS message. Thanks for the kind words
@@Peppermint1 do you have any idea how to clear SRS airbag red logo on dash? We removed seats unplugged wiring reinstalled and the warning won’t get cleared away any idea?
@@suitealek Did the light come on after disconnecting the seats ? May look again closely at the seat connectors. This red light means there is a fault somewhere in the SRS system, which means one or more airbags will not deploy in a crash
@@Peppermint1 yes, after seats disconnected to install new fuel pump system. Should we disconnect all wiring to seats again? Did I overlook a connection? Any insights welcome!
@@suitealek We must disconnect the battery 10 minutes before unplugging a seat connector - since the seat has a wire for the side airbag in the seat side bolster. Try to have a second look at those large connectors in front of the seat, I think I have videos for at least one type, depending of the year. Make sure the connection is 'closed' properly and that there are no pins that may have got bent. If all checks fine, you may want to have someone with Vida or a performant aftermarket code reader trying to clear the SRS code and light
Welcome. It is true filming is not always easy - working with a single hand, sometimes I wish I had someone to film all these videos while I work. Cheers
So now my headlights wont go off when i turn on the car.. also the radio lights do not work ... and the dash light is quite dim .. i wonder if this is due to this module failing ? can you advise? on these symptoms?
@@bobbyperu8414 by removing the back and reheating the solder contacts. I did it and it worked again for a couple months but failed again so I ended up replacing mine with an used one.
@@nadaproblem806 could this unit result in me not being able to adjust my low beams electrically? they are stuck in a low position, even if i adjust the white screws on the headlights themselves
@@oskarjennische2490 this unit controls, high, low and fog functions as well as the dimmer. if your talking about adjustments directing the beams this has no effect. that should be strictly mechanical from the adjusting screws on the headlight unit itself. hope this helps
![Lp. Сердце Вселенной #30 ДВА В ОДНОМ [Один человек]• Майнкрафт](http://i.ytimg.com/vi/nrXy15orKhY/mqdefault.jpg)
Thank you for the clear instructions. I had to replace my switch and it only took a couple minutes after seeing how.
I was worried that I would run out of gas on my way home last week since the fuel door unlock button is on the same module, but luckily that button worked and I was able to fill the tank.
Hi. My DIM/climate zone is dark and highbeams wont stay on + when i lock the car my orange/hazard lights wont blink. You think this switch could be the problem too?
Just picked up a 2007 s60R. There is no illumination coming from behind the gauges. Would the cause possibly be the dimmer switch?
It's nice to hear you so calm when you're struggling as hell to get that flashright right while still trying to point and film the details in a very tight spot. Nice instructions. Don't you need to disconnect the battery before you replace that switch ?
Hi, no need to undo the battery for this switch unit, it is not part of the canbus network so it won't trigger the SRS message. Thanks for the kind words
@@Peppermint1 do you have any idea how to clear SRS airbag red logo on dash? We removed seats unplugged wiring reinstalled and the warning won’t get cleared away any idea?
@@suitealek Did the light come on after disconnecting the seats ? May look again closely at the seat connectors. This red light means there is a fault somewhere in the SRS system, which means one or more airbags will not deploy in a crash
@@Peppermint1 yes, after seats disconnected to install new fuel pump system.
Should we disconnect all wiring to seats again? Did I overlook a connection? Any insights welcome!
@@suitealek We must disconnect the battery 10 minutes before unplugging a seat connector - since the seat has a wire for the side airbag in the seat side bolster. Try to have a second look at those large connectors in front of the seat, I think I have videos for at least one type, depending of the year. Make sure the connection is 'closed' properly and that there are no pins that may have got bent. If all checks fine, you may want to have someone with Vida or a performant aftermarket code reader trying to clear the SRS code and light
Thanks, looks you so struggling to take this image, much appreciated for the video, it also use same ways to open the switch in S80 2.0T. 😃
Welcome. It is true filming is not always easy - working with a single hand, sometimes I wish I had someone to film all these videos while I work. Cheers
why make fuses box reach so difficult
So now my headlights wont go off when i turn on the car.. also the radio lights do not work ... and the dash light is quite dim .. i wonder if this is due to this module failing ? can you advise? on these symptoms?
I would think it's think module but ask here as well www.matthewsvolvosite.com/forums/
Hello i own a s80 2003 and both xenon arent working but the bulbs are new
Done that and still no parking lights at the front...Fuses are ok..bulbs are new led ...but the old ones were ok too
thanks
did u disconnect battery first ?
Not needed for this small repair. Only when removing parts such as the radio, climate control unit, instrument cluster or computer modules
@@Peppermint1 ok just did mine ...was very easy ...no need to loosen the "clip" screw back there ...just unplug and take it out ....🤫
This part is repairable don't just replace if you have a soldering iron and ten minutes
Good to know
how ? any link to how to do this ?
@@bobbyperu8414 by removing the back and reheating the solder contacts. I did it and it worked again for a couple months but failed again so I ended up replacing mine with an used one.
@@nadaproblem806 could this unit result in me not being able to adjust my low beams electrically? they are stuck in a low position, even if i adjust the white screws on the headlights themselves
@@oskarjennische2490 this unit controls, high, low and fog functions as well as the dimmer. if your talking about adjustments directing the beams this has no effect. that should be strictly mechanical from the adjusting screws on the headlight unit itself.
hope this helps
do you how many lights are in that unit?
No, but usually the backlight on these units are tiny SMD leds which are usually not user replaceable
Dont try to do it urself.. you will cut urself. The video show you. Hahhaaa
You will bleed.
xD
ua-cam.com/video/IFde3gXmmGY/v-deo.html
That may work, but notice the metal tabs can be stuck and difficult to release (the one in this video took some convincing).