Hi Sir. Can You please show or make a video of how to setup de Maverick to work with only de bottle adaptador regulator?? In order to hace a bigger plenum. Thanks
Hello Mr. Rowe. I have a suggestion for when you’re taking out the o-rings from the reg adjustment screw and from the regulator housing (10x1.5)…it’s a million times easier if you use a sewing needle instead of flattening your pick or using needle nose pliers like at 4:52. Since you’re replacing them, you might as well poke it and insert the need horizontally into the o-ring. Removing it becomes so much easier. Just a trick I use that I thought I’d share. Awesome guide!
Show só falta encontrar o gênio aqui no Brasil KKK sempre desejando muito mais sucesso de um fã seu é do seu trabalho só possou desejar se pode-se daria mais like garantido sempre
Just changed low pressure ( #2 ) on my maverick, but the damn thing loose pressure thru the venting hole, there are no reg creep, regulated shooting pressure remain 100 bar i set it to, even when bottle are empty over night.
Earnest....a tip from the laziest bastard on the planet.(or just an old toolmaker)..run over to the lathe turn up a piece of delron or nylon to slide up inside the reg body from the opposite side......has to be flush with the "bottom of o-ring groove ) for (4x1.5 -nbr 70 or 90) depending on which parts list your looking at....lol....NO MORE FIGHTING IT....Slides right in.....WITHOUT pokin it with allen key....push mine in with a finger......Now..I think that tip deserves an EXTRA lump a coal in my christmas sock...dont you...Santa..lol...lov the vids man....
Hey Ernest great video. My Mav had an extra o ring on the regulator adjustment screw right under the threads. Normal? It’s never been apart and I bought it new.
Hi, great video. I have a problem. When the regulators are fully open, I have a maximum pressure value of 120 BAR. Why can't a higher pressure value be set?
Hey Ernest, Tried removing the o-ring inside the adapter and failed miserably! And idea who has one in stock new or used . When I screw the bottle on , the air just shoots out the atmosphere hole. Ty
HI ernest Thanx for your advice , i could get the same , i issue i am facing now is that there is a leakage of air from the vent hole in the plenum cylinder (opposite side of the 2nd regulator), and as soon as i put the bottle the leakage starts . i seek your advice onto which of the O rings may have been busted, look forward to your reply, thanx
Hi Earnest I recently removed my AMP regulator on my maverick due to a damaged bottle adapter. But as I found out the schematic for the parts is the same as the dream line Drawing F10101. It states on the drawing that the there are 2 different Belleville washers. Washer 10x4, 2x .06 and washer 10x4, 2x .05. I am not sure in which order these are supposed to be stacked and if it makes any difference.
There is a test for that before adjusting anything, document the speed between timed shots for example, take five shots three seconds apart and document all the speed, then 4 seconds apart, then 5 seconds apart and so on till 10 seconds apart, now u can see the refresh rate of the current setup
Know what?? The spring thickness?? If so when you remove the spring washer measure the thickness- the thickness are mix matches, to get factor settings, some set are two different thickness and some same thickness- so measure your combination of sizes for reference to reassemble. Its one Method to set a spring washers strength.
Hola ... tengo una fx maverick spinner ... Si eres tan amable me gustaría que me dijeras donde puedo conseguir el util extractor de la válbula ... un saludo
I really wish you would do a short video going into detail about the washer stack arrangement. Still a little confused about that step. Thanks!
Hi Sir. Can You please show or make a video of how to setup de Maverick to work with only de bottle adaptador regulator?? In order to hace a bigger plenum. Thanks
Hello Mr. Rowe. I have a suggestion for when you’re taking out the o-rings from the reg adjustment screw and from the regulator housing (10x1.5)…it’s a million times easier if you use a sewing needle instead of flattening your pick or using needle nose pliers like at 4:52. Since you’re replacing them, you might as well poke it and insert the need horizontally into the o-ring. Removing it becomes so much easier. Just a trick I use that I thought I’d share. Awesome guide!
Nice one!
@@ernestrowe5061 we would like a video, showing off this custom maverick.
@@ernestrowe5061 What kind of material did you use on the tip of the disc springs pin, where does the sealing with the adjustment screw?
Show só falta encontrar o gênio aqui no Brasil KKK sempre desejando muito mais sucesso de um fã seu é do seu trabalho só possou desejar se pode-se daria mais like garantido sempre
Super !
Just changed low pressure ( #2 ) on my maverick, but the damn thing loose pressure thru the venting hole, there are no reg creep, regulated shooting pressure remain 100 bar i set it to, even when bottle are empty over night.
Where do you get the tool that removes the washers.
Earnest....a tip from the laziest bastard on the planet.(or just an old toolmaker)..run over to the lathe turn up a piece of delron or nylon to slide up inside the reg body from the opposite side......has to be flush with the "bottom of o-ring groove ) for (4x1.5 -nbr 70 or 90) depending on which parts list your looking at....lol....NO MORE FIGHTING IT....Slides right in.....WITHOUT pokin it with allen key....push mine in with a finger......Now..I think that tip deserves an EXTRA lump a coal in my christmas sock...dont you...Santa..lol...lov the vids man....
You make it look easy but it’s not bad once you done it few times
Any one that disassemble hundreds of regulators can make it look easy 😊
what bad rider is that where can i get same setup … do you work on mavericks with power problems ??
Hey Ernest great video. My Mav had an extra o ring on the regulator adjustment screw right under the threads. Normal? It’s never been apart and I bought it new.
does it look like theres three orings? there should only be 2
Hi, great video. I have a problem. When the regulators are fully open, I have a maximum pressure value of 120 BAR. Why can't a higher pressure value be set?
Hey Ernest,
Tried removing the o-ring inside the adapter and failed miserably! And idea who has one in stock new or used . When I screw the bottle on , the air just shoots out the atmosphere hole. Ty
HI ernest
Thanx for your advice , i could get the same , i issue i am facing now is that there is a leakage of air from the vent hole
in the plenum cylinder (opposite side of the 2nd regulator), and as soon as i put the bottle the leakage starts .
i seek your advice onto which of the O rings may have been busted, look forward to your reply, thanx
What size is the O rings on the adjuster mine are bad and can't find nothing that small
Earnest where did you get the Arca rail for the Maverick? Please help me I’ve been looking for one.
Hi Earnest I recently removed my AMP regulator on my maverick due to a damaged bottle adapter. But as I found out the schematic for the parts is the same as the dream line Drawing F10101. It states on the drawing that the there are 2 different Belleville washers. Washer 10x4, 2x .06 and washer 10x4, 2x .05. I am not sure in which order these are supposed to be stacked and if it makes any difference.
As long you have enough reg pressure any stack configuration will do.
awesome video as always brother. when are you coming back up to shoot
Hi Norm, man still trying to got Rick to come-seems like we all busy for now😂
@@ernestrowe5061 I hear you buddy. we have to get together soon even if its just for dinner brother
hi great video , i have question regrading refresh rate , within what time(seconds) does the refill happen to set pressure post firing a shot , thanx
There is a test for that before adjusting anything,
document the speed between timed shots for example, take five shots three seconds apart and document all the speed, then 4 seconds apart, then 5 seconds apart and so on till 10 seconds apart, now u can see the refresh rate of the current setup
The reg piston is an upgrade to the Delrin one used in previous models? If so, would it be available for Gen one impact with a shorter piston (14mm)?
No, haven’t seen a brass 14mm piston
Where did he put the thickest spring washer? Is it me or does he just ramble ...
Where can I get that tool to put all the plate?? Any site??
At: 910airguntuningandrepairsllc.com
what are the gains in removing the second regulator?
More plenum volume of 160cc, with 2nd reg 56cc plenum. 160cc plenum more power, lower ES, more shots
So make a video about that, How to - Maverick with only one regulator ?!
Easy, you buy a plenum tube and you put it on the front of the existing plenum and now you have double the volume 164 cc
So does the factory know this lol.
Know what?? The spring thickness?? If so when you remove the spring washer measure the thickness- the thickness are mix matches, to get factor settings, some set are two different thickness and some same thickness- so measure your combination of sizes for reference to reassemble. Its one
Method to set a spring washers strength.
@@ernestrowe5061 I think he means does the factory know you’re putting your Maverick on steroids lol. I would assume they do.
@@DocMustafa --> everyone knows i don’t ishoot stock AG 😊
Hola ... tengo una fx maverick spinner ... Si eres tan amable me gustaría que me dijeras donde puedo conseguir el util extractor de la válbula ... un saludo