My new Wildcat BT came from factory producing 10.5 ft/lbs on setting 7 of the power wheel with 15.89gr pellets and I couldn't be arsed with the hassle of sending it back so this video is absolute GOLD for me. Thanks from a new subscriber!
What a superb video. I have new FX Maverick that has inconsistent accuracy. It's going back ti the RFD. When it's returned if it's not sorted I'll replace the regs myself.
Good idea, another thing to check is try the rifle without the cheek piece installed, on some rifles the mag hits the cheek piece and causes mis-alignment of the mag and barrel, damaging the pellets as they enter the barrel. Just another thing to double check. Thanks for watching.
@@sub12airgunners Hi Thanks for your prompt reply. If I don't get a satisfactory solution from my RFD and the distributor, do I need to replace the regs or just strip them and reinstall . If I need to purchase new regs where can I obtain them? Do you have an on line shop? Many thanks.
@@jonpear2560 I have the same problem w my Maverick. I just got it back and was shooting it yesterday. it was shooting great but after a couple hundred shots I started getting up to 30fps spreads. This video was just what I was looking for, probably going to have to do this. It took three weeks to get it repaired last time so will be doing it myself.
Cool video Jeff... is there a new style of cheek piece coming out!!!..where did you get those pressure gauges and it looks like a new style of cocking lever.
Hi, supposedly a cheek piece that has the proper cutout for the mag, the current one hits the magazine. The gauges are from ali express, link below, and the cocking handle is one we make, and is available on eBay from bagnall and kirkwood. www.aliexpress.com/item/1005002053621959.html?spm=a2g0o.productlist.0.0.2c247cf2FLtcnK&algo_pvid=aefacfc8-529d-4756-ac03-f5c1b4bcebee&algo_expid=aefacfc8-529d-4756-ac03-f5c1b4bcebee-0&btsid=2100bb4716180077412505725ee5cf&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_
I still have the “ wrong” cheekpiece. Did modify a few magazines, ground and polished the sharp point. Works fine now. Like the Maverick. Have it now set on 50 J, my range limit. Get 200 + shots at 50 J with 20 gr Nielsen slugs. No need for me anymore to lug a big tank around. 😀. My Mk3 wildcat has the same setting and does 20 mm at 100 mtr. They are in .22. Hope the Maverick will do the same. Have not shot the Maverick at the range yet, cant waite to go......
good idea with the mags, hope fully the new cheek pieces will be available soon though, sounds like yours is shooting well though, very efficient. no range time yet but hopefully next week ill be going so lots of testing to do, not shot at a range for more than a year now so very excited. Thanks for watching.
@@sub12airgunners Had some problems. 2 bad superior.22 70 cm liners. Have now an” old” from last year pellet liner init. Have it retuned now, from 1st reg at 145 2st reg at 105 (factory setting) to 1st reg at 120 2st reg at 80 bar. And did the hammer adjustment thing,thanks for the how to, and the numbers are promising. As pellets do better than most slugs in this liner I have it set with the new tune now, the JSB 18.13 pellet at around 920 fps. That is around 47/48J. Now I have to wait for 2 weeks….range maintenance…..
whats your ebay seller name im in the usa and will you ship i would like to buy from you because you have very good explanations and i like to buy from people that take time to explain like you do
Grate video, picked my maverick up last week , went back after 2 days with a leak and a zero shift issue , thought I’d use the warranty while it’s available, but if it comes back with the same issues this video will help me no end 👍🏼
The Mavericks are certainly not having a good launch, lots of problems and leaks, I guess it is leaking at the little joiner piece between the block and cylinder, that's a common area, I think they machined the O ring groove a little deep on the block and its causing some Mavericks to leak, I did put a bit of sealant around my one as a preemptive fix, I think I showed it in the vid near the beginning, but good luck, personally I don't think its a rifle I will be keeping hold of. Anyway Thanks for watching.
@@philnixon7168 Possibly, if you have to go down that route it may work with a very slightly over sized O-ring but if I is leaking from there I would recommend just a dab of loctite 545, its a pneumatic sealant and should do the job, although the choice is yours. Thanks for watching.
Great overview thank you. Are you able to answer a question please? I took my rear regulator out and when I put it back in it does not regulate anymore. I just get the front reg pressure on the rear gauge even when the rear is screwed mostly all the way in. Its like it just bypassing the rear reg. I don't have any air leaks and even bought a new reg and installed it but it still isn't regulating. Do you have any idea what it could be? Thank you
I changed to a HUma reg, and it did not work well for me ( not able to get flat strings ), changing back to FX it now leak to atmosphere, and even more strange both regulators now do that CUZ i tried to put the HUma one back in the gun. I simply do not get it. Also changed a few O-rings on the FX regulator but its still the same. Regulated pressure are fine no creep or bleed on that, just the damn leao out the overflow hole. Inclined to buy a complete new regulator, just they dont seem to sell anywhere in the EU where i can pay with creditcard.
Can you just unscrew the bottle safely with air in it? :D damn im watching this many times and trying to learn along the way.. dual regs is a little tricky!
On my Crown mk2 the transfer port adjuster became misaligned so that max power was between settings (FAC), I thought I had sorted it but now it will move slightly off its setting when I am doing a shot string over the chrono. Could you do a video on this part of the crown mk2 perhaps 👍
I have a question. I bought the huma reg for the maverick and the reg body does not fit the maverick and is the right part. I measure the amp reg body and is 10.7mm thick and the huma is 10.88mm. Why do you think than happens. The huma reg that I got is supposed to fit the maverick. Thank you for the info.
very informative video sir i have just bought a maverick and there is a leak on the 1st regulator , so can i assume that as per the video the leak can be adjusted by cleaning the adjuster screw to start with ?
Ashish, a caution in Mavericks purchased in India recently…. even if You have got that issue solved, take a pause, inspect all the O-rings thoroughly as they may be dry… Lube them and their seat, appropriately, Seat them, Assemble all back, fill air, take few shots (10-15 for .177), and let it settle for a day ~24hrs… De-gas next day, and refill, and check for any leaks at all in a 5hr window by noticing drop in pressure.
@@SoulSniped thanx durgesh , i have a few more queries regarding the regulator which is not been very consistent in delivering the required output and settling back quickly , can we connect
Great vid and thx for the answer on your other thread. Mine is shooting a bit low, how do i get it up a little bit in power, can i just screw the "powerplenum"-regulator out a little bit? Or do i have to go thru all this shown in the video..
once the anti tamper is out you should just be able to adjust the reg up a little, you may have to re adjust the hammer spring adjuster in the back to re balance things but just a little increase in reg pressure should get it to where you want it. Thanks for watching.
Hi. I have a problem with FX Maverick sniper. When the regulators are fully open, I have a maximum pressure value of 120 BAR. Why is it not possible to set a higher pressure value?
video of how too replace the first pressure gauge ie u put a digital gauge in how would love too see that as I would like too do the same also ur videos are very good
You can watch the dissasembly and reassembly maverick vids on the channel and you can see the procedure, its very easy to do though just undo the old gauges and put the new ones in, if you buy the digital ones make sure you get the BSP threads. Thanks for watching.
I sell reg pullers and valve seat removers on my Ebay shop link below. Thanks for watching www.ebay.co.uk/sch/geoffeve-7/m.html?_nkw=&_armrs=1&_ipg=&_from=
Great video, just got my maverick but my rear reg is positioned just slightly under the chassis how can it be moved so I can gain access to the adjuster
@@davidkelly212 on the Mavericks you have to loosen the cylinder clamps, and turn the cylinder itself, make sure the back cap is tight on the nut near the block and turn the cylinder round to where you want the reg. Thanks of watching.
Unfortunately not, we don't ship outside the UK, you can buy it from bagnall and kirkwood though they sell internationally. You can find the tools by searching. link below. spares.bagnallandkirkwood.co.uk/
They put the prices up since this vid but link below. Thanks for watching. www.aliexpress.com/item/1005002596229302.html?spm=a2g0o.productlist.0.0.21947c87dGOKQf&algo_pvid=ebee8175-7211-4afd-9180-9b6f101a6c5d&algo_expid=ebee8175-7211-4afd-9180-9b6f101a6c5d-0&btsid=0b0a556316217994320535498e9be4&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_
Also, what causes the inconsistency? Worn O-Rings/dirty regulator? I noticed when I’m having the problem I can’t hear the air transfer after I pull the trigger. I hear after every shot I should hear the air transfer. Thanks for the information
you can sometimes use a biro pen to get it out, some of the pens have the right ID when you take out the ink tube. excessive grease in the Belleville washers can cause issues, also damaged o rings on the piston can make it a bit sticky in the reg housing, you should hear the reg refill after each shot if its not then the reg could be sticking. Thanks for watching.
hi , I bought an electronic gauges for my impact and I notice that the reg pressure rise up ate least 5 bar after fill the plenum, I take a shot let the pleanum fill anda check the pressure, 1 min later I check it again and its 5 bar higher, any idea how to solve this?
That's Reg creep, you may have to replace the delrin piston in the regulator, or it could be one of the O rings in the regulator, typically its one of the small o rings on the adjuster screw or the top of the reg piston is damaged and is causing you some creep. Thanks for watching.
@@sub12airgunners well thank you for replying, I watched a ernest video and i'm gonna polish the delrin piston and the adjuster screw and see if it solves the problem. one more time thank you for your reply.
@@sub12airgunners well I polish the piston and I solve the problem of creep but now if I shoot in low power with a 100 bar reg the plenum only fill at the second shot, it's like the reg don't recognize that the pressure in plenum changes, any suggestion to solve this? Ps: I rebuild the reg with no lubrification, do you think that it's the problem?
Hi Tim, I had them up on Ebay, but they all sold out, ill make some more in the week so keep checking but ill make 10+ so you should be able to find them in a few days. Thanks for watching.
I have run out at the moment but heres a link to my Ebay, ill post more as I make them. www.ebay.co.uk/sch/geoffeve-7/m.html?item=373570787127&hash=item56fa8dd737%3Ag%3AmscAAOSwnRZgjCK1&rt=nc&_trksid=p2047675.l2562
My new Wildcat BT came from factory producing 10.5 ft/lbs on setting 7 of the power wheel with 15.89gr pellets and I couldn't be arsed with the hassle of sending it back so this video is absolute GOLD for me. Thanks from a new subscriber!
That is awesome!
What a superb video. I have new FX Maverick that has inconsistent accuracy. It's going back ti the RFD. When it's returned if it's not sorted I'll replace the regs myself.
Good idea, another thing to check is try the rifle without the cheek piece installed, on some rifles the mag hits the cheek piece and causes mis-alignment of the mag and barrel, damaging the pellets as they enter the barrel. Just another thing to double check. Thanks for watching.
@@sub12airgunners Hi Thanks for your prompt reply. If I don't get a satisfactory solution from my RFD and the distributor, do I need to replace the regs or just strip them and reinstall . If I need to purchase new regs where can I obtain them? Do you have an on line shop? Many thanks.
@@jonpear2560 I have the same problem w my Maverick. I just got it back and was shooting it yesterday. it was shooting great but after a couple hundred shots I started getting up to 30fps spreads. This video was just what I was looking for, probably going to have to do this. It took three weeks to get it repaired last time so will be doing it myself.
@@bobfisher9452 My thoughts exactly. Can't be doing with this level of service.
Great video really clear and informative thank you👍 👌
Glad it was helpful! Thanks for watching.
Cool video Jeff... is there a new style of cheek piece coming out!!!..where did you get those pressure gauges and it looks like a new style of cocking lever.
Hi, supposedly a cheek piece that has the proper cutout for the mag, the current one hits the magazine. The gauges are from ali express, link below, and the cocking handle is one we make, and is available on eBay from bagnall and kirkwood.
www.aliexpress.com/item/1005002053621959.html?spm=a2g0o.productlist.0.0.2c247cf2FLtcnK&algo_pvid=aefacfc8-529d-4756-ac03-f5c1b4bcebee&algo_expid=aefacfc8-529d-4756-ac03-f5c1b4bcebee-0&btsid=2100bb4716180077412505725ee5cf&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_
I still have the “ wrong” cheekpiece. Did modify a few magazines, ground and polished the sharp point. Works fine now. Like the Maverick. Have it now set on 50 J, my range limit. Get 200 + shots at 50 J with 20 gr Nielsen slugs. No need for me anymore to lug a big tank around. 😀. My Mk3 wildcat has the same setting and does 20 mm at 100 mtr. They are in .22. Hope the Maverick will do the same. Have not shot the Maverick at the range yet, cant waite to go......
good idea with the mags, hope fully the new cheek pieces will be available soon though, sounds like yours is shooting well though, very efficient. no range time yet but hopefully next week ill be going so lots of testing to do, not shot at a range for more than a year now so very excited. Thanks for watching.
@@sub12airgunners Had some problems. 2 bad superior.22 70 cm liners. Have now an” old” from last year pellet liner init. Have it retuned now, from 1st reg at 145 2st reg at 105 (factory setting) to 1st reg at 120 2st reg at 80 bar. And did the hammer adjustment thing,thanks for the how to, and the numbers are promising. As pellets do better than most slugs in this liner I have it set with the new tune now, the JSB 18.13 pellet at around 920 fps. That is around 47/48J. Now I have to wait for 2 weeks….range maintenance…..
whats your ebay seller name im in the usa and will you ship i would like to buy from you because you have very good explanations and i like to buy from people that take time to explain like you do
Ditto, I REALLY want to purchase your tool it looks to be quite handy.
Grate video, picked my maverick up last week , went back after 2 days with a leak and a zero shift issue , thought I’d use the warranty while it’s available, but if it comes back with the same issues this video will help me no end 👍🏼
The Mavericks are certainly not having a good launch, lots of problems and leaks, I guess it is leaking at the little joiner piece between the block and cylinder, that's a common area, I think they machined the O ring groove a little deep on the block and its causing some Mavericks to leak, I did put a bit of sealant around my one as a preemptive fix, I think I showed it in the vid near the beginning, but good luck, personally I don't think its a rifle I will be keeping hold of. Anyway Thanks for watching.
@@sub12airgunners thanks for the reply, would if be a good idea to put a slightly oversized o ring in place of it ?
It*
@@philnixon7168 Possibly, if you have to go down that route it may work with a very slightly over sized O-ring but if I is leaking from there I would recommend just a dab of loctite 545, its a pneumatic sealant and should do the job, although the choice is yours. Thanks for watching.
@@sub12airgunners thanks again for the reply …fingers crossed it comes back leak free , if not I’ll try that first thanks for the advice 👍🏼
Great overview thank you. Are you able to answer a question please? I took my rear regulator out and when I put it back in it does not regulate anymore. I just get the front reg pressure on the rear gauge even when the rear is screwed mostly all the way in. Its like it just bypassing the rear reg. I don't have any air leaks and even bought a new reg and installed it but it still isn't regulating. Do you have any idea what it could be? Thank you
I changed to a HUma reg, and it did not work well for me ( not able to get flat strings ), changing back to FX it now leak to atmosphere, and even more strange both regulators now do that CUZ i tried to put the HUma one back in the gun.
I simply do not get it.
Also changed a few O-rings on the FX regulator but its still the same.
Regulated pressure are fine no creep or bleed on that, just the damn leao out the overflow hole.
Inclined to buy a complete new regulator, just they dont seem to sell anywhere in the EU where i can pay with creditcard.
Thank you another excellent post...
No problem, Thanks for watching.
Very nice
Thanks for watching.
Can you just unscrew the bottle safely with air in it? :D damn im watching this many times and trying to learn along the way.. dual regs is a little tricky!
Yep the bottles have a one way valve fitted and they close as you unscrew the bottle. Thanks for watching glad you are learning.
Awesome. Very informative. Thanks.
Great video, easy to follow.
Thanks, glad you enjoyed it, Thanks for watching.
On my Crown mk2 the transfer port adjuster became misaligned so that max power was between settings (FAC), I thought I had sorted it but now it will move slightly off its setting when I am doing a shot string over the chrono. Could you do a video on this part of the crown mk2 perhaps 👍
Yeah it could be a number of things, but ill try and make a short vid in the near future. Thanks for watching.
Thanks for the clarification. Explained well. 👍
Glad you liked it thanks for watching.
I realize I'm kinda randomly asking but do anybody know a good site to watch new tv shows online?
@Tyler Martin Lately I have been using FlixZone. You can find it on google :)
I have a question. I bought the huma reg for the maverick and the reg body does not fit the maverick and is the right part. I measure the amp reg body and is 10.7mm thick and the huma is 10.88mm. Why do you think than happens. The huma reg that I got is supposed to fit the maverick. Thank you for the info.
very informative video sir i have just bought a maverick and there is a leak on the 1st regulator , so can i assume that as per the video the leak can be adjusted by cleaning the adjuster screw to start with ?
Ashish, a caution in Mavericks purchased in India recently…. even if You have got that issue solved, take a pause, inspect all the O-rings thoroughly as they may be dry…
Lube them and their seat, appropriately, Seat them, Assemble all back, fill air, take few shots (10-15 for .177), and let it settle for a day ~24hrs…
De-gas next day, and refill, and check for any leaks at all in a 5hr window by noticing drop in pressure.
@@SoulSniped thanx durgesh , i have a few more queries regarding the regulator which is not been very consistent in delivering the required output and settling back quickly , can we connect
Great vid and thx for the answer on your other thread. Mine is shooting a bit low, how do i get it up a little bit in power, can i just screw the "powerplenum"-regulator out a little bit? Or do i have to go thru all this shown in the video..
once the anti tamper is out you should just be able to adjust the reg up a little, you may have to re adjust the hammer spring adjuster in the back to re balance things but just a little increase in reg pressure should get it to where you want it. Thanks for watching.
Perfect video,
I have a request, not a single link on reg puller posted here is working anymore, can you give an actual one please ?
Thank you.
No problem, link below. Thanks for watching.
www.ebay.co.uk/itm/373975875026
@@sub12airgunners thank you for the quick response,
but i'm very sad, doesnt post to my country, only within the UK ....
all to best to you, Kurz.
Hi. I have a problem with FX Maverick sniper. When the regulators are fully open, I have a maximum pressure value of 120 BAR. Why is it not possible to set a higher pressure value?
video of how too replace the first pressure gauge ie u put a digital gauge in how would love too see that as I would like too do the same also ur videos are very good
You can watch the dissasembly and reassembly maverick vids on the channel and you can see the procedure, its very easy to do though just undo the old gauges and put the new ones in, if you buy the digital ones make sure you get the BSP threads. Thanks for watching.
How long is the power plenum of the maverick from the cylinder to the end and how much is the outer diameter
Great video. You mention you sell kits and tools. Where can I find reference to these
I sell reg pullers and valve seat removers on my Ebay shop link below. Thanks for watching
www.ebay.co.uk/sch/geoffeve-7/m.html?_nkw=&_armrs=1&_ipg=&_from=
Many Many Thanks Brother......
Most welcome, thanks for watching
Where have you bougth your allen keys with that handels ?
nice! do you have a link where i can get the reg. puller?
ebay www.ebay.co.uk/itm/375091735874
btw you can scan the qr code to see the serial number
Do you still sell the piston puller? A link would be appreciated.
Hi yes we still sell all the bits www.ebay.co.uk/itm/374671996366
@@sub12airgunners May I still order it? It says uk buyers only.
Keren
Where is the ebay link for the reg puller
Do you still make and sell the piston removal tool? Link in previous comment seems to be dead. Thanks
yep, link below, thanks for watching.
www.ebay.co.uk/itm/373975875026?hash=item5712b2fdd2:g:J5EAAOSwNwpgWKA7
Very well explained fella 👍 is the a anti tamper on the hammer? Love the guages you have fitted.
No AT on the hammer, just the regs, ill have a vid on the gauges coming soon. Thanks for watching.
Brilliant video have tried to find the piston puller on ebay have you a link? also cant seem to find your website help needed cheers
Heres the link, thanks for watching.
www.ebay.co.uk/itm/373685698165?hash=item5701673e75:g:J5EAAOSwNwpgWKA7
@@sub12airgunners thanks for the link and thanks for the detailed videos👌
Great video, just got my maverick but my rear reg is positioned just slightly under the chassis how can it be moved so I can gain access to the adjuster
You can rotate the tube slightly (with the rifle de pressurized) to line the reg up in a better position. Thanks for watching
I can degas the gun ,I've just done that to fit a carbon bottle but would I have to loosen anything to turn the plenum
@@davidkelly212 on the Mavericks you have to loosen the cylinder clamps, and turn the cylinder itself, make sure the back cap is tight on the nut near the block and turn the cylinder round to where you want the reg. Thanks of watching.
excellent thankyou very much
No problem glad you enjoyed it, thanks for watching.
nice one 👍
Thank you! Cheers!
Just subbed.. Am getting this fx.... Is this a reg rebuild on a 12 ft UK rifle... Thanks...
Yep, UK spec sub 12, thanks for watching.
Another great video fella ....
It's nice to see the "Facebook experts" debunked (again) 👍
Yeah, they do like to have a moan don't they. thanks for watching.
Looked on ebay for a reg puller, unfortunately can't seem to find one, can anyone advise?
Went to eBay with no luck in finding one. Can you tell me what name to look under? I’m hoping that you ship to the states.
Unfortunately not, we don't ship outside the UK, you can buy it from bagnall and kirkwood though they sell internationally. You can find the tools by searching. link below.
spares.bagnallandkirkwood.co.uk/
Hi have u got a link for Pressure Gauges thanks and love your vids been a big help thank you
They put the prices up since this vid but link below. Thanks for watching.
www.aliexpress.com/item/1005002596229302.html?spm=a2g0o.productlist.0.0.21947c87dGOKQf&algo_pvid=ebee8175-7211-4afd-9180-9b6f101a6c5d&algo_expid=ebee8175-7211-4afd-9180-9b6f101a6c5d-0&btsid=0b0a556316217994320535498e9be4&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_
Why does my reg screw have 3 orings rather then 2 like yours?
Not sure I have not seen one like that before. Is it a newer model maybe? Thanks for watching
Question, What’s the best way to pull the piston if I don’t have the tool? Thanks
Also, what causes the inconsistency? Worn O-Rings/dirty regulator? I noticed when I’m having the problem I can’t hear the air transfer after I pull the trigger. I hear after every shot I should hear the air transfer. Thanks for the information
you can sometimes use a biro pen to get it out, some of the pens have the right ID when you take out the ink tube. excessive grease in the Belleville washers can cause issues, also damaged o rings on the piston can make it a bit sticky in the reg housing, you should hear the reg refill after each shot if its not then the reg could be sticking. Thanks for watching.
Nice video sir, subscribed.
Where can i buy that "regpuller-tool", ebay link?
Hi, they are on Ebay, link below, thanks for watching.
www.ebay.co.uk/itm/373562171758?hash=item56fa0a616e:g:J5EAAOSwNwpgWKA7
@@sub12airgunners how can I get hold of one please
@@sub12airgunners The page is missing.
hi , I bought an electronic gauges for my impact and I notice that the reg pressure rise up ate least 5 bar after fill the plenum, I take a shot let the pleanum fill anda check the pressure, 1 min later I check it again and its 5 bar higher, any idea how to solve this?
That's Reg creep, you may have to replace the delrin piston in the regulator, or it could be one of the O rings in the regulator, typically its one of the small o rings on the adjuster screw or the top of the reg piston is damaged and is causing you some creep. Thanks for watching.
@@sub12airgunners well thank you for replying, I watched a ernest video and i'm gonna polish the delrin piston and the adjuster screw and see if it solves the problem. one more time thank you for your reply.
@@sub12airgunners well I polish the piston and I solve the problem of creep but now if I shoot in low power with a 100 bar reg the plenum only fill at the second shot, it's like the reg don't recognize that the pressure in plenum changes, any suggestion to solve this? Ps: I rebuild the reg with no lubrification, do you think that it's the problem?
Hi is valve stop housing same on sub 12 as fac (high power) ??
The valve housing is the same although the valve seat may be a slightly bigger diameter in FAC. Thanks for watching.
Can someone give me a link to buying a reg puller please, The Ebay link below shows nothing.
Hi , link below. Thanks for watching.
www.ebay.co.uk/itm/373781114992?hash=item5707173070:g:J5EAAOSwNwpgWKA7
Hi there I'd like to buy a reg piston puller but I can't seem to find them on eBay.
Tim
Hi Tim, I had them up on Ebay, but they all sold out, ill make some more in the week so keep checking but ill make 10+ so you should be able to find them in a few days. Thanks for watching.
Ok thanks I'll watch out for them
do you sell the reg piston pulling tool ?
yes they are on ebay 😀
When can I buy the pistin puller
Bagnall & Kirkwood sell them 😀
Bonjour j'aimerais avoir ton lien pour acheter extracteur de régulateur?
Hi sorry we only sell in the UK
I want to order nyunit.can you send it to Indonesia.
Can you send me the link to buy that reg puller?
They are on eBay, link below, thanks for watching.
www.ebay.co.uk/itm/373590947455?hash=item56fbc1767f:g:J5EAAOSwNwpgWKA7
Hi! what's your seller name on eBay?
Where can I get a link for the reg puller please?
I have run out at the moment but heres a link to my Ebay, ill post more as I make them.
www.ebay.co.uk/sch/geoffeve-7/m.html?item=373570787127&hash=item56fa8dd737%3Ag%3AmscAAOSwnRZgjCK1&rt=nc&_trksid=p2047675.l2562
Hi and thanks but Im in New Zealand would you send a couple ok kits please? and cost to thanks...Brian
That surface looks a lot like concrete and it bothered me a lot until I decided it must be a rubber or urethane pad. You need a new surface. Meh, :p
Yeah, its a yoga mat it stated off nice but picks up holes and dents super quick ill have to find a new filming mat. Thanks for watching.
@@sub12airgunners Well the videos are great, I just kept thinking you were going to scratch it, silly me. A new surface would look neat though.
Can do my gun
Sorry we don't work other peoples guns