@@jeznermediamagicwhat?????? Hey can you help us out a little bit? Would be nice to know what we’re doing. I just bought the module as well. I don’t know what I’m doing. lol
@@jeznermediamagic I already asked a question but did you notice though that when you switch to auxiliary source video looks worse the color is worse and it’s not as sharp. Is there something that I’m doing wrong? Maybe I need to go on the settings or whatever?
I did the same mod did you notice when you switched to the auxiliary which is the SpeedyBee? The video looks worse. The colors look worse. It looks a tiny bit greater. Can’t figure out what’s going on. It totally works, but just wanna switch over it’s noticeable.
I go to scan channels press scan it finds a proper channel. What else do I need to do to get my signal that high? It’s very strange doesn’t matter if I’m using a tiny whoop or one of my 5 inch quads. Etc. I would say it’s at about 70% highest ever yours is literally at like 90% 95% signal
What is your mw output on the vtx? Super clean footage.
what screws do you use to hold the two pieces together?
m2 screws
Thanks for the reply. Just printed my module cover and gonna try to put this together today. Excited to get some more range
I’m a little confused to where the plug fits into the module. I am not finding like an aux plug in port on the SpeedyBee
@@tharrimo4able enjoy the diy
@@jeznermediamagicwhat?????? Hey can you help us out a little bit? Would be nice to know what we’re doing. I just bought the module as well. I don’t know what I’m doing. lol
9-pins in that module did u use it? to connect to the AUX of the scout ??? can u pls explain how to connect via aux port (goggles)
PINOUT (starts from buttom 1-9 facing to you correct orrientation of fonts when looking at it)
9-
8-
7-
6- Video
5-
4-
3- GND
2-
1- 5 Volts
He explained it there’s only three pins that you need 1-3 and 6.
@@jeznermediamagic I already asked a question but did you notice though that when you switch to auxiliary source video looks worse the color is worse and it’s not as sharp. Is there something that I’m doing wrong? Maybe I need to go on the settings or whatever?
Is there anyway you could post which ports you plugged the 3 prong into the module? It would help a lot.
PINOUT (starts from buttom 1-9 facing to you correct orrientation of fonts when looking at it)
9-
8-
7-
6- Video
5-
4-
3- GND
2-
1- 5 Volts
I did the same mod did you notice when you switched to the auxiliary which is the SpeedyBee? The video looks worse. The colors look worse. It looks a tiny bit greater. Can’t figure out what’s going on. It totally works, but just wanna switch over it’s noticeable.
i think you can change the color settings on the fatshark, i just used default settings
We need a new link for 3 pin cable
s.click.aliexpress.com/e/_DmW5M39
Why you put this receiver? Signal is better?
@@LuigiRega-lb8ph yes for signal improvement, can use different type of antennas.
Which cable is it? There’s like 20 options single connector double connector. Two pin three pin four pin. Which one is it thank you.
Also. Where do you put the three wires on the back of the receiver? Do you have to solder it?
Also, my signal level is never as high as yours, no matter what.
I go to scan channels press scan it finds a proper channel. What else do I need to do to get my signal that high? It’s very strange doesn’t matter if I’m using a tiny whoop or one of my 5 inch quads. Etc.
I would say it’s at about 70% highest ever yours is literally at like 90% 95% signal
And also you’re going through room to room. Now I’m annoyed lol
@@LoVeAmBiEnT what antenna you using? and do you have a lot of wifi signal in the house? try to change different channels also