Thanks man! Haven't done d13s in a long time and remembered you were responsible for me getting my first one done! I need to start posting my procedures also because they just may benefit someone!
When pulling injectors, loosen either the feed or return line on the head to let fuel drain. When pulling cups, use a 15/16 ratcheting wrench ($20 from Home Depot) on the big nut, stick a rolling head prybar or screwdriver in a rocker shaft hole to keep the 13mm wrench from moving. You’ll have all cups pulled in 3 minutes.
When I start my truck in the morning and sometimes it doesn't start, the noise comes as if the truck starts now, but it doesn't start, it stops by itself, my truck is 2017 and has 8 lac mileage, if anyone can tell me anything.
When is temperature is very down same problem show me , today I am right now Amarillo tx eh is temperature’s after I trun off my truck and maybe 10 min after I staring again same problem, but right now I press the race pandle after that is start my truck ,
@ 9:00 I would recommend using rubber bands to keep the exhaust plungers from falling out of the rockers when removing the rocker shaft, makes re-installation a lot easier.
Great video I've worked at mack dealer couple years back and totally almost forgot the procedure installing the cups. And Chronicle cup thing for injectors tips .great explained
What about the residue or brush bristles that are falling into the cylinder? What if pieces get between a valve and seat? I see videos saying don't get loose EGR soot into the intake tract. Wouldn't this be the same?
I bought the swage tool for installation but welded a tap to a piece of threaded rod and made a bridge to pull old cups and it has been working fine for years now
Thanks a lot for posting this, I'm doing this job tomorrow, I already started this afternoon and removed the valve cover and rocker arm bolts, I'm going to make that angle iron tool first thing in the morning, do you mind telling me the thread size of those 19mm bolts so I could picked them up when I go to buy the angle iron? Thanks again
how much would you charge to come to Arizona and teach our yard mechanic how to perform this job. We would pay your flight and hotel . it be nice to have some overhead adjustment videos. Our mechanics are really good with other engines its just Volvo that they avoid any major repairs. For example they did a head gasket on a 13 and had some problems with it. Volvo dealers are really expensive and always swamped with work. great videos btw Thanks
Great video 👍 I have been going from shop to shop with injector cups problem. Just day ago pulled out of the Volvo dealer drove 550miles and my coolant starts leaking again pushing it through the injectors, pressurizing the system. Had two full engine rebuilds on two separate trucks, basically every year I need an engine rebuild. Do you think that the injector cup leak issue could cause a future engine failure? Because I have to rebuild whole engine after injector cups leak I don’t know if it could be connected in anyway but it seems like coolant washes out cylinder oil and engine running dry long enough and after the leak fix that cylinder locks up and drops rod destroying entire engine. Idk 🙈
Hey brother you said something about reusing the injectors. If i want to reuse mine do i need to do something with them. My injectors seem to work fine but i have bubbles in the fuel tank comming out of return line. Also long starts. And my last trip i had severe vibration under heavy load. Not sure i that was caused by leaking cups or just clogged fuel filter. Was no vibration when drove home empty for over 500mi. Also how much you charge for injector work, do you give waranty for how long. And how much are injectors from the dealer. I have the tool for pulling cups from ebay slightly different than yours but same principal. Have you heard if those work ok. Im thinking how to fix my truck cobsidering all possible options. Have 6 kids bills are coming truck needs work. Thanks дякую
hey i have a 2007 volvo d670 10 speed D13 ENGINE my truck set about 2 years and my truck was running good when i originally park it....and it has about 1/2 tank of fuel in it ..so i got ready to start the truck up after 2 years of sitting and got some new batteries in it and it started right up idling beautiful i go to drive it and its if i dont have no power it takes along time to get to 50mph and i have the gas pedal to the floor ..i changed the two filters and put some additive in it i put howes and lucas injector cleaner and fuel conditioner in i went back out to test drive it .and it seemed to be alittle better i was able to get 60 mph but it still taking along time to get there i drove about 90 miles.but it still doing the same thing it is not smoking it but it is actually running good but i dont have no power...there is no code lights on..do you think i need to put somemore additive in it and drive it more..
Greetings. I changed the injector cups and left the same injectors because they were good. gauge too. and now when i turn this on for more than 2 minutes the accelerator pedal doesn't respond. what could have happened?
wow... great video, thanks for sharing. I got a question if you don't mind? When the hard cranking reason is just injector cups , are you always recommend to change the injectors too even if they are in good shape?? And secondly where is your shop located? Thanks a million if you reply. I assume you're a great mechanic by this video.
If they are in good shape, you don't have to replace them, and you can replace only ones that/if they are bad. Only reason they are recommended to change in a set is Labor Time (Money), since you would have to do everything again to change injectors in case they fail soon after you install new cups.
Hey question, my truck is taking forever to start (d13) and it stays misfiring. I got some bubbles in the tank. But her i open the the priming pump it came lose. Do you think its soaking air ? Or my problem is injectors and cups?
Could be a few things, cups most likely on this engine but will need diagnose by mechanic, could also be filter housing or check valve or hole in fuel line
Have you seen any failures with injectors or any other part in general that damaged the turbine veins on a vg turbo causing the armature to seize up? On a D13 engine. Thanks. Awesome video too.
Tow months ago I replaced the 6 cups and one injector because I was having diasl in the coolent , and now I have misfire cylinder 5 , can I replace the injectors only Without replacing the cops ?
@@cardinaltruckservice3753 thanks for your help , what about the one brand new injector i replaced tow months ago , do I need to replace it also or just buy 5 new injector , it's almost 600$
@@wilfredvictore91 could be condensation but if crank case pressure high, truck running rough and smoke from blow by, either worn rings or cracked piston or liner, may need overhaul.
If it has electrical problem you will get code, it could be leaking fuel into oil so you need visual exam, it could cause engine to misfire underload which may or may not give a code
Cardinal Truck Service sir if you read my comment please like and answer then i ll see earlier I wanna go to your location to check my truck if need to fix there is there your shop name or contact?
Sorry I forgot to ask you another question!! Are injector cups come in 2 different kind of material ?? Like in the past they were made by hard plastic or metal which metals lasted longer ! Is that right? Are metal ones do better than un metal injector cups ? ( quality wise ) Thanks man
Not really necessary unless the injectors were the problem! Volvo doesn't use high pressure rail on d13 that's a good thing so the rail isn't where most problems are! The cup's design and injectors (because of cup design) are the most common problem besides oil leak at the timing gear area at the back of block!
@@cardinaltruckservice3753 They still have it and they ordered a solenoid I don't know who they are planning on paying for it. They took valve cover back off and said everything looked good with new orings put on. Just sucks bill is going to be big anyway
sir i have a problem if i start the engine d13a volvo and i put automatic or manual no accelerator,.after 1 to 2mins.accelerator work..in neutral position its good,.what is the problem?
When I start my truck in the morning and sometimes it doesn't start, the noise comes as if the truck starts now, but it doesn't start, it stops by itself, my truck is 2017 and has 8 lac mileage, if anyone can tell me anything.
the steel sleeves are miles better than the origional copper sleeves. 9/10 times you would either pull the tip out with the old tool that threaded through the tip, or you would pull the sleeve and the tip would stay in the head :D
Cardinal Truck Service Hi brother I live in Reisterstown MD and I have d13 volvo I go to your shop can you check advise what really need to do Problem is hard starts if I use manual pump stats easy I replaced new battery, new starter , new water separetor but still same
Single injector electrical fault is usually bad injector, test it by disconnecting injector and connecting to a spare injector. Just the wire, no need to remove injector. See if you still get code
Interesting. I use to work in a machine shop years ago, making a few different turned parts for these injectors. So if your lorry was build between 2004 and 2011, and the injector failed. Sorry about that.
That means the cups are bad and leaking coolant into the cylinder! Get it fixed asap or you'll be replacing a egr valve, egr cooler, turbo, doc, dpf, nox sensor, Delta P sensor and your intake valves will be not happy!
Could be a few thing but most likely cups if hard to start/ need to prime fuel before starting, air in return, bubbles if you look in fuel tanks. Injectors need replaced if the have pitting due to bad cups or sometimes they misfire under load
When taking the rockershaft loose you should have pulled the rear 18 mm bolt and all the front 13mm bolts then loosened all the rear 13mm bolts in stages. With the plungers on the exhaust brake rockers before you put the lifting tool on you can use old red or green orings and put them around the plunger and the rocker to hold the plunger so you can keep them in place. And the cup pulling tool can stay together I use the same one and dont take it apart. And your cup swedging tool should be updated to the new style. Just my input from another volvo/mack tech
Thanks for input, I did unscrew in stages in video like you do but I only do middle 3 or 4 front or rear, faster that way. I'll try your other suggestions though
Need to add update to the new installer. the one you are using is pulling the bottom of the cup when it is installed. the new tool pushed down when installing.
First bulletin says to repair them...then the 2nd bulletin says, don't repair them, replace them. All exhaust rockers are on national backorder. So, I being a good tech, use my TIG welder to spot weld the pistons.
@@cardinaltruckservice3753 I need to replace the cups and injectors on my 2010 Volvo d13... but the truck has been deleted.. can you still program the injectors?
Thanks man! Haven't done d13s in a long time and remembered you were responsible for me getting my first one done! I need to start posting my procedures also because they just may benefit someone!
This channel is an absolute goldmine of information. I got lucky when I found this channel!
When pulling injectors, loosen either the feed or return line on the head to let fuel drain. When pulling cups, use a 15/16 ratcheting wrench ($20 from Home Depot) on the big nut, stick a rolling head prybar or screwdriver in a rocker shaft hole to keep the 13mm wrench from moving. You’ll have all cups pulled in 3 minutes.
When I start my truck in the morning and sometimes it doesn't start, the noise comes as if the truck starts now, but it doesn't start, it stops by itself, my truck is 2017 and has 8 lac mileage, if anyone can tell me anything.
When is temperature is very down same problem show me , today I am right now Amarillo tx eh is temperature’s after I trun off my truck and maybe 10 min after I staring again same problem, but right now I press the race pandle after that is start my truck ,
Thanks for the video, did my first six pack w/ cuppers and the client was more than satisfied. Happy holidays !
Ima bout to wish me luck
@@mmmaaannnyyydid you do it ? Lol
@ 9:00 I would recommend using rubber bands to keep the exhaust plungers from falling out of the rockers when removing the rocker shaft, makes re-installation a lot easier.
We use the EGR crossover pipe, green o-rings, to hold the plungers in.
I just welded a tap to some all thread and made a bridge to pull the old cups. I have used it many times for over a decade and still works
Great video I've worked at mack dealer couple years back and totally almost forgot the procedure installing the cups. And Chronicle cup thing for injectors tips .great explained
Feed line is the better option, since it's toward the rear of the head and typically is a little lower than the front
Good to see some Craftsman tools in action at the pro level.
What about the residue or brush bristles that are falling into the cylinder?
What if pieces get between a valve and seat?
I see videos saying don't get loose EGR soot into the intake tract.
Wouldn't this be the same?
thank you, sir. I am very helped. May God bless you
I bought the swage tool for installation but welded a tap to a piece of threaded rod and made a bridge to pull old cups and it has been working fine for years now
Thanks a lot for posting this, I'm doing this job tomorrow, I already started this afternoon and removed the valve cover and rocker arm bolts, I'm going to make that angle iron tool first thing in the morning, do you mind telling me the thread size of those 19mm bolts so I could picked them up when I go to buy the angle iron? Thanks again
My cups won’t come out with the tool. And I’m doing it the way you explained it on the video. Any tips ?
Hello sir thanks for the video and what is the sign of bad injectors or cap ? Thanks 🙏
Hello, excellent video, thank you very much
How many millimeters are those two screws to lift all the rocker arms?
how much would you charge to come to Arizona and teach our yard mechanic how to perform this job. We would pay your flight and hotel . it be nice to have some overhead adjustment videos. Our mechanics are really good with other engines its just Volvo that they avoid any major repairs. For example they did a head gasket on a 13 and had some problems with it. Volvo dealers are really expensive and always swamped with work. great videos btw Thanks
Great video. Thanks
Please which injector is Fuel 1 cylinder 3 for Volvo d13?
Great video 👍
I have been going from shop to shop with injector cups problem. Just day ago pulled out of the Volvo dealer drove 550miles and my coolant starts leaking again pushing it through the injectors, pressurizing the system. Had two full engine rebuilds on two separate trucks, basically every year I need an engine rebuild. Do you think that the injector cup leak issue could cause a future engine failure? Because I have to rebuild whole engine after injector cups leak I don’t know if it could be connected in anyway but it seems like coolant washes out cylinder oil and engine running dry long enough and after the leak fix that cylinder locks up and drops rod destroying entire engine. Idk 🙈
Hellos sir,
How far apart is the center of the holes for the tool to lift the rocker arm shaft . Trying to make my own
You looks professional mechanic for me beo thak you about this vedio, can i know where is your shop location please?
Hey brother you said something about reusing the injectors. If i want to reuse mine do i need to do something with them. My injectors seem to work fine but i have bubbles in the fuel tank comming out of return line. Also long starts. And my last trip i had severe vibration under heavy load. Not sure i that was caused by leaking cups or just clogged fuel filter. Was no vibration when drove home empty for over 500mi. Also how much you charge for injector work, do you give waranty for how long. And how much are injectors from the dealer. I have the tool for pulling cups from ebay slightly different than yours but same principal. Have you heard if those work ok. Im thinking how to fix my truck cobsidering all possible options. Have 6 kids bills are coming truck needs work. Thanks дякую
Best video so far thanks brother 🙏 😊
Thank you for making this saved me from big mistakes
What size are the bolts used through the angle iron into the rocker arm?
Hello sir ,
When you said you vacuumed the cylinder to prevent hydro lock what did you use for that .
You can get a vacuum brake bleeder with 1/4 air hose into the cylinder
What are some of the symptoms to tell you it’s a bad injector? I have an active p020413 code saying open circuit cylinder 4
hey i have a 2007 volvo d670 10 speed D13 ENGINE my truck set about 2 years and my truck was running good when i originally park it....and it has about 1/2 tank of fuel in it ..so i got ready to start the truck up after 2 years of sitting and got some new batteries in it and it started right up idling beautiful i go to drive it and its if i dont have no power it takes along time to get to 50mph and i have the gas pedal to the floor ..i changed the two filters and put some additive in it i put howes and lucas injector cleaner and fuel conditioner in i went back out to test drive it .and it seemed to be alittle better i was able to get 60 mph but it still taking along time to get there i drove about 90 miles.but it still doing the same thing it is not smoking it but it is actually running good but i dont have no power...there is no code lights on..do you think i need to put somemore additive in it and drive it more..
What’s the Torque on the racker Arm and all other
Thank you
Greetings. I changed the injector cups and left the same injectors because they were good. gauge too. and now when i turn this on for more than 2 minutes the accelerator pedal doesn't respond. what could have happened?
wow... great video, thanks for sharing. I got a question if you don't mind? When the hard cranking reason is just injector cups , are you always recommend to change the injectors too even if they are in good shape?? And secondly where is your shop located? Thanks a million if you reply. I assume you're a great mechanic by this video.
If they are in good shape, you don't have to replace them, and you can replace only ones that/if they are bad. Only reason they are recommended to change in a set is Labor Time (Money), since you would have to do everything again to change injectors in case they fail soon after you install new cups.
Hey question, my truck is taking forever to start (d13) and it stays misfiring. I got some bubbles in the tank. But her i open the the priming pump it came lose. Do you think its soaking air ? Or my problem is injectors and cups?
Could be a few things, cups most likely on this engine but will need diagnose by mechanic, could also be filter housing or check valve or hole in fuel line
Just wondering, why did you remove the coolant?
if you don't drain coolant it's going to leak in your engine(oil pan)
Hi bro i have volvo genset TAD 734 GE, i would like the references of the tools to desassemble and reassemble of the injectror sleeves.
Or tools of injector cup
Good video. Does the same process apply to a Volvo d12 engine ? Thanks in advance.
No it doesn't. In fact this process is not used by Volvo anymore. They have new tools
YOU CAN USE A SCREW INTO THE BOTTOM OF THE CUP AND PULL IT OUT WITH SLIDE HAMMER DONT NEED TO BUY EXPENSIVE TOOLS
I got the cups out and the head is pitted, do I need a new one or just leav it as it is. Please help
What happens to any brush material and debris that falls onto the piston?
+Tucker The Trucker it's vacuumed out, plastic bristles are probably safer for use where tip of cup goes
Where can I get the inyector cup removal and installer tool ?
Dealer should have it. Otherwise you can get aftermarket for much cheaper but maybe won't last long
H0i. Is possible to measure Cyl Temperature with an infrared termometer and get real values? Where the dot must be put?
Do I need to change 6 or just 1 mine 4 one is bad please advise
hello, what's was the symptoms of bed injector cups?
Hard to start condition, over pressurized coolant reservior, coolant pushing out of reservoir. Low power, over temperature in aftertreatment
Have you seen any failures with injectors or any other part in general that damaged the turbine veins on a vg turbo causing the armature to seize up? On a D13 engine. Thanks. Awesome video too.
Something from engine would probably be piece of broken valve. It could get stuck from build up of soot or uneven wear also
@@cardinaltruckservice3753Ok, thank you.
I have a 2013 volvo vnl needed to replace injector cups as well, Kalinchuk where your shop located?
Email us semitrucksdiy@gmail.com for appointment and more info, thanks. We are near harrisonburg, va
Kalinchuk DIY how much do you charge to do cups and injectors and how long would it take to do it?
If I need to replace the injector harness on a d12 motor , do I need to take any of that stuff like rocker arms and jakes
Haven't done it on a d12 but I don't think you would have to remove any of that
Very informative video. Where can i purchase his injectore sleew remova/installer?
TAP THE BOTTOM OF THE CUP AND TREAD A SliDE HAMMER INTO IT AND PULL OUT THE CUP EASY AND CHEAP DONT NEED EXPENSIVE TOLLS TO DO THIS JOB.
anywhere online, amazon
Injector cup tip broken and stuck on cylinder head. Any suggestions how to remove it?
Need a special tap and bolt. Not sure where you can get one
@@cardinaltruckservice3753 thanks!
Do I have to chance the injectors everytime I change a cup ? Or could I just change the cups only.
Cups need to be changed any time injectors are removed. Injectors need to be replaced only if its worn or pitted on mating surface to cup
I need to know how to refill the coolant system using vacunm
Tow months ago I replaced the 6 cups and one injector because I was having diasl in the coolent , and now I have misfire cylinder 5 , can I replace the injectors only Without replacing the cops ?
You can try but you might have to do it again, it's cheaper to do it right once. It doesnt add much time to change one cup when your already there
@@cardinaltruckservice3753 thanks for your help , what about the one brand new injector i replaced tow months ago , do I need to replace it also or just buy 5 new injector , it's almost 600$
@@mahmoudlover1 yes you can put 5 as long as the new one is not the problem
@@cardinaltruckservice3753yes the new one cylinder#2 and the problem cylinder#5 misfire ,
sir I will ask something..if the crankcase pressure too high,if you are running the engine its automatically shotdown,what is the cause?
+Wilfred Victore check blow by if nothing there probably bad sensor
from the breter there is a white smoke coming out there.
@@wilfredvictore91 could be condensation but if crank case pressure high, truck running rough and smoke from blow by, either worn rings or cracked piston or liner, may need overhaul.
Good morning I have a question what tools exactly do I need to remove an alternator from a 2006 Volvo vnl with the engine D12 thank you in advance
Basic hand tools. 1/2 ratchet and some sockets dont know exact size, it right on top so should be pretty easy
@@cardinaltruckservice3753 ok thank you
Good Job 👍 Very Helpful ...Thank you
Hello there, how many hours are given by the book for this job?
+Eddy sky 10h
Nr on the special tools from Volvo?
How do you diagnose a bad injector is there any tools or procedures for diagnosing?
If it has electrical problem you will get code, it could be leaking fuel into oil so you need visual exam, it could cause engine to misfire underload which may or may not give a code
My truck idles very rough and it cracks long before starting are those also related to a bad injector?
Not sure without seeing the truck but could be a injector leaking into cylinder or maybe injector cups
Cardinal Truck Service sir if you read my comment please like and answer then i ll see earlier I wanna go to your location to check my truck if need to fix there is there your shop name or contact?
Sorry I forgot to ask you another question!! Are injector cups come in 2 different kind of material ?? Like in the past they were made by hard plastic or metal which metals lasted longer ! Is that right? Are metal ones do better than un metal injector cups ? ( quality wise )
Thanks man
Used to be copper, now they are steel
What happens if you switch the order of the cylinders on the rockers
Is it same thing for D12
Should the fuel rail be replaced while replacing the injectors?
Not really necessary unless the injectors were the problem! Volvo doesn't use high pressure rail on d13 that's a good thing so the rail isn't where most problems are! The cup's design and injectors (because of cup design) are the most common problem besides oil leak at the timing gear area at the back of block!
sir no need to timing if you change bad injector?
How much would this job be on a 2013 Volvo d 13
About $4200-$4400
Should I adjust my values while replacing injectors
Yes if take rocker shaft of good idea to adjust. You will need to adjust injector anyway
I had injectors put in and my jake quit working. Any relationship?
Yes, take it back to the shop
@@cardinaltruckservice3753 They still have it and they ordered a solenoid I don't know who they are planning on paying for it. They took valve cover back off and said everything looked good with new orings put on. Just sucks bill is going to be big anyway
Do you overhaul D12 ? And how much it cost?
sir i have a problem if i start the engine d13a volvo and i put automatic or manual no accelerator,.after 1 to 2mins.accelerator work..in neutral position its good,.what is the problem?
throttle pedal may be the cause, had the same problem with a FM9 / ishift gearbox
Tps or throttle position sensor!
Where can I get that tools?
Does anyone know if this repair is typically covered by extended warranty?
When I start my truck in the morning and sometimes it doesn't start, the noise comes as if the truck starts now, but it doesn't start, it stops by itself, my truck is 2017 and has 8 lac mileage, if anyone can tell me anything.
Maybe air getting in system ie injector cups, filter housing, davco or pressure relief valve sticking if you still have it
@@cardinaltruckservice3753 thanks sir
the steel sleeves are miles better than the origional copper sleeves. 9/10 times you would either pull the tip out with the old tool that threaded through the tip, or you would pull the sleeve and the tip would stay in the head :D
Has anyone tried that aftermarket injector tools for sale everywhere
What state you’re located? If I need to bring my truck?
Virginia
Cardinal Truck Service Hi brother I live in Reisterstown MD and I have d13 volvo I go to your shop can you check advise what really need to do Problem is hard starts if I use manual pump stats easy I replaced new battery, new starter , new water separetor but still same
@@baltimoremd5415 www.cardinaltruckservice.com for more info, thank you.
What happens if you forget to number the injectors and forget which one went where? What could be the affects or outcome?
Nothing just have injector codes reprogrammed
Cool thanks
can you help me to solve the problem on the volvo d13 engine error and injector #5 electrical fault..thank you
Single injector electrical fault is usually bad injector, test it by disconnecting injector and connecting to a spare injector. Just the wire, no need to remove injector. See if you still get code
i check on the monitor and the warning is engine error and i check the faults is injector #5 electrical fault..whats is the cause sir?
@@wilfredvictore2886 bad injector
thank you for the reply
sir how about if the injector ask a code,.what is the code to be use?thank you
Interesting. I use to work in a machine shop years ago, making a few different turned parts for these injectors. So if your lorry was build between 2004 and 2011, and the injector failed. Sorry about that.
sir what is the problem if the smoke is white,.volvo d13a fmx
That means the cups are bad and leaking coolant into the cylinder! Get it fixed asap or you'll be replacing a egr valve, egr cooler, turbo, doc, dpf, nox sensor, Delta P sensor and your intake valves will be not happy!
what would be the signs of me needing to replace my injectors and cups
Could be a few thing but most likely cups if hard to start/ need to prime fuel before starting, air in return, bubbles if you look in fuel tanks. Injectors need replaced if the have pitting due to bad cups or sometimes they misfire under load
How many hours does this job take?
10h
Very good video.
How can I get these injector/eui?
Thank you sir for your video I appreciate it
Greetings from Dubai
When taking the rockershaft loose you should have pulled the rear 18 mm bolt and all the front 13mm bolts then loosened all the rear 13mm bolts in stages. With the plungers on the exhaust brake rockers before you put the lifting tool on you can use old red or green orings and put them around the plunger and the rocker to hold the plunger so you can keep them in place. And the cup pulling tool can stay together I use the same one and dont take it apart. And your cup swedging tool should be updated to the new style. Just my input from another volvo/mack tech
Thanks for input, I did unscrew in stages in video like you do but I only do middle 3 or 4 front or rear, faster that way. I'll try your other suggestions though
@@cardinaltruckservice3753 p
بارك الله بكم
Really good video.
Will that tool work on D12 engine?
No. There's a completely different set of tools for the D12.
Need to add update to the new installer. the one you are using is pulling the bottom of the cup when it is installed. the new tool pushed down when installing.
also you don;t have to take the puller apart like that each time. it can stay as a whole unit
this tool pushes down and runs a pin through it to spread out the bottom, can't get the cup on without taking it apart
@@cardinaltruckservice3753 im talking about the cup puller you dont have to take it apart.
@@nickpurcella6590 yea this video needs a few updates but no time now
Where your shop at
Shop in Virginia, Visit cardinaltruckservice.com for more info
What is the measurement in mm of entry and exit
Valve lash? Intake 0.203mm exhaust 1mm
you forgot to mention that you need to repair the exhust plungers if thay back out
First bulletin says to repair them...then the 2nd bulletin says, don't repair them, replace them. All exhaust rockers are on national backorder. So, I being a good tech, use my TIG welder to spot weld the pistons.
@@BurninBogey7 that’s good. We’ve just been red lock tightening them😅
Where are you located and can you please provide contact info. I need my injectors done.
+singto syvoravong sure, email me at semitrucksdiy@gmail.com thanks
@@cardinaltruckservice3753 I need to replace the cups and injectors on my 2010 Volvo d13... but the truck has been deleted.. can you still program the injectors?
Why don’t you upload anymore bro ?
Any mechanic in the Texas area to do this on D13 Volvo ???
Просто SUPER,нам бы такой специальный инструмент в сервис!!!
I've had mine done 3 times. They are failing again. Why?
Did you replace injectors also? The seat can get worn, or bad install
@@cardinaltruckservice3753 yes. Volvo has replaced the injectors and cups 3 times. They are failing again.
Serviço de qualidade 👏👏
Luciano Coelho has
@@ninderkhella650? has
@@ninderkhella650 qual seu país?
Nicely done
Thank u bro
Thank you
Excellent explanation.
and I get impatient changing guitar strings