What? Have you swapped nozzles on any other printers? This is convoluted to swap a nozzle tip. 6mm wrench and a couple of seconds and most printers are done. No cables, no hex cap screws. You shouldn't have to basically swap an entire hot end to change your nozzle.
All I’m gonna say, I’m new to 3D printing and got a P1S, somehow my hotend got filament harden inside and I could not cleaned so I swapped to the replacement hotend (0.04) and (without) any instructions I swapped. To the point: my printer gave me a error code when I started (0003_0002_0001_0001). Bambu Lab sent me a complete hotend assembly. Before I was going to replace everything I just happen to see your video, followed your directions and my printer works perfectly!, thank you!
2:46 No no no! The clip slides off the end. Notice how there are "tabs" on the metal, that's so they can slide up and over the heater. You remove it the opposite of how you install it at 7:30. Even if you don't re-use it, removing it like you did could damage the thermistor.
I am confused. I received a Bambu X1C a few days ago. and I ordered a few spare nozzles for it but you are not replacing the nozzle, per se, you are replacing almost the entire hot end. Perhaps "nozzle" means something else in Bambu speak.
LOL, I almost feel like could do this (X1 Carbon) but my 80 year old hands say, would be better to just take out one piece and put in a complete new one. Unhooking and hooking wires, we can do.
If you break your thermister when trying to remove its finished and ruined. I believe it needs to be a continuous loop and mine broke. I suppose you could sodder it back together.
Tip: Don't pull out the connectors by the wires, as tempting as that is, you may pull out one or more of the wires from the connector. Don't ask me how I know.
The X1E nozzle is not compatible with the X1C, as it is made of different materials that are designed to go to a hotter temperature. The X1E can only have the complete hot end assembly replaced, not just the nozzle.
You can just buy a new hotend that has all those parts attached already, the fan, thermistor and heater cartridge. Then just unscrew the old and swap in the new, replace screws and plug in the wires. Much easier and faster, and they don't cost much more.
The white part is the heater not heat sink !
i love how much easier it is on Bambu 3d printers its SUCH a hassle on other printers
What? Have you swapped nozzles on any other printers? This is convoluted to swap a nozzle tip. 6mm wrench and a couple of seconds and most printers are done. No cables, no hex cap screws. You shouldn't have to basically swap an entire hot end to change your nozzle.
@@ronaldhiser860 the NOZZLE is easy.
hot end is a mess and a total time waster from how hard it is on my old elegoo nep 3
@@ronaldhiser860 Ironically, on the Bamboo A1 familiy it's even easier than with a standard nozzle on most printers.
A great video. Thank you very much. Not even Bambulab has done so well. I will save it for the future. Good images and shots
All I’m gonna say, I’m new to 3D printing and got a P1S, somehow my hotend got filament harden inside and I could not cleaned so I swapped to the replacement hotend (0.04) and (without) any instructions I swapped. To the point: my printer gave me a error code when I started (0003_0002_0001_0001). Bambu Lab sent me a complete hotend assembly. Before I was going to replace everything I just happen to see your video, followed your directions and my printer works perfectly!, thank you!
Use a 1.5mm alan key heat it with a tourch and stick it into the hotend. Let it cool then pull it out. I had to use a vice mine was really in there.
@@DennisCrawfordJr
You can also heat the Nozzle from the outside with the lighter, that way it is easier to pull out
Whatever Bambu is paying you, they owe you a lot more money! Your videos have been super helpful.
Ha Ha! They don't pay me or anything. I just make them to help everyone. Glad you like them and they helped you!
2:46 No no no! The clip slides off the end. Notice how there are "tabs" on the metal, that's so they can slide up and over the heater. You remove it the opposite of how you install it at 7:30. Even if you don't re-use it, removing it like you did could damage the thermistor.
Thanks for creating the video I was able to successfully switch over the components to the new Hotend and I’m back up and running.
Thanks to you I changed my bambu ps1 nozzle and I’m back in business thanks so much awesome and very helpful video 😊
Very nicely done video step by step 👍🏼
Great video as always 👍
Does the slicer automatically change speed / flow (optimize) settings once you select the 0.2 nozzle? Im on X1C
it seems a bit cramped on mine, with the build plat up. Is there any way to drop the build plate down?
Do this! I just did and it was way easier than in this video.
can we use cpu Grease from a pc?
Chris do these come pre assembled? Ty for the video man 😎👍
Yah they do. You can buy them preassembled on bambus store for a significant upcharge
Also, I can't see how you got filament plastic up there? The nozzle part is covered with insulating rubber
What should I do if I accidentally pull one of the wires off
Only buy the complete hotends, got it
I replaced the nozzle which fixed my z axis homing problem but now im getting a temperature problem error.
Great Video thanks!
What would change I would remove. The connections 1st.
Can we get an update on the Bulbasaur project, I’m very interested in what it looks like now
This really helped thanks alot 🙂
I am confused. I received a Bambu X1C a few days ago. and I ordered a few spare nozzles for it but you are not replacing the nozzle, per se, you are replacing almost the entire hot end. Perhaps "nozzle" means something else in Bambu speak.
Coming from enders replacing whole hotend seems illigal to me
*IMPORTANT* hey, what if the model is hollow from the beginning only? Can we still change the thickness of the wall later on slicer still??
just what i needed to know thank you
LOL, I almost feel like could do this (X1 Carbon) but my 80 year old hands say, would be better to just take out one piece and put in a complete new one. Unhooking and hooking wires, we can do.
Clip was in different position at start, and at end of video. I am guessing it doesn't really matter all too much.
If you break your thermister when trying to remove its finished and ruined. I believe it needs to be a continuous loop and mine broke. I suppose you could sodder it back together.
Wait, are you from Pittsburgh??
Why are you all complaining about how complicated this is? It takes a couple of minutes and saves you 20 euro.
Yea good video but I suggest a pair of long nose to remove the cables and for the love of God clean the excess thermal paste.
Great Video! Add chapters so we can jump to the section(s) we need. Thanks!
Would just recommend buy the full assembly.
man after watching this video i'm firmly convinced spending the extra money is worth it 🤣🤣
Hands down this
Yeah, I bought nozzles because somehow I just thought the nozzles clipped in. I wonder where I got that idea.
What’s the point of replacing the fan and thermister if they haven’t failed?
This was my thought as soon as I saw all the extra steps.
Tip: Don't pull out the connectors by the wires, as tempting as that is, you may pull out one or more of the wires from the connector. Don't ask me how I know.
How do you know?
The X1E nozzle is not compatible with the X1C, as it is made of different materials that are designed to go to a hotter temperature. The X1E can only have the complete hot end assembly replaced, not just the nozzle.
Um, how about how to change it WITHOUT destroying the clip, for those of use who got their X1C's with nothing but the new nozzle, not even a new sock?
i personally would of changed the heating element and thermistor. and u didnt put any thermal paste on thermistor
What about unloading the fillament first?
lol I forgot that step and had to put it back together =P
@@cyka_delik9537 LOL me too. rookie mistake
Ur voice sounds like a young Cole sprouse kinda
Just get the complete nozzle with fan already installed and save yourself a headache.
Just buy the whole kit. This is just asking for issues.
cheezus, in the whole entire video you couldnt wipe that excessive greese off the nozzle and you put a sock over it, gosh you're messy =D
isn't this the whole hotend? the nozzle is just the tip
It sickens me how many times you said "actually" in this video. We're going to ACTUALLY blah blah blah,,, really?? actually??
no god👎
THANK GOD I PURCHASED THE FULL ASSEMBLY FUCK ALL THAT
I would buy an extra printer with a different nozzle size. too much work imo
You can just buy a new hotend that has all those parts attached already, the fan, thermistor and heater cartridge. Then just unscrew the old and swap in the new, replace screws and plug in the wires. Much easier and faster, and they don't cost much more.