Genius tools and ideas for the skilled worker at work
Вставка
- Опубліковано 28 лют 2024
- Teaching metal turning, teaching general metal turning.
Innovative and new daily methods in the field of metal turning, the method of operating the metal lathe, and identifying all its parts and the laws of metal turning.
The tools used in turning metals and the method of preparing them for work.
Daily positions on a metal lathe
Daily innovations on the metal lathe
Components of teaching metal turning, teaching general metal turning.
Innovative and new daily methods in the field of metal turning, the method of operating the metal lathe, and identifying all its parts and the laws of metal turning.
The tools used in turning metals and the method of preparing them for work.
Daily positions on a metal lathe
Daily innovations on the metal lathe
Components of metal turning workshops
The most important daily repetitive tasks in the field of metals
والله ياباشاء انك رجل مبدع ومعلم وكريم الي متبخلتش علينا بعلوماتك القيمة سهلت علينااشياءً كثيرة وربي بيرزقك على وضوحك الله يجزاك خير الحزاء🌹🌹🌹🌹🌹
Sir bahut badiya apane bnaya video se kuch alag sikhne Mila
Very good idea, it much better for multiple start threading
I learned a lot of things from your videos!
🙏🏽🙏🏽❤
if he extended the r/h cutting tool it would cut deeper thus cutting down the process, at the minute what is he achieving
В чем плюс-то? Второй резец не доходит же?!...
Boa noite senhor existe alguma maneira de usinar um diâmetro interno de um rolamento cônico
What advantage does this threading tool with 2 cutting edges have? I don't see anyone. He wants to make a screw with a thread pitch of 2 mm. It shows the distance between the two cutting edges as approx. 10 mm and that is 5 thread turns and therefore a pitch of 2 mm. If you slow down the video speed (0.25x speed) at 9:30 you can see that the feed of the lathe is set to 2mm per revolution. The right of the two cutting edges follows 5 spindle revolutions later, more or less exactly in the same track as the left cutting edge. And therefore it is not a multi-start thread.
Both cutting edges are also set to the same diameter, so there are no differences between roughing and finishing cutting edges. The right cutting edge shouldn't actually make any chips - the fact that it does so is due to the manufacturing tolerance - the exact size of the cutting tips is certainly not 10.0mm apart (that's not how you measure it like in the video) - and if the real distance is, for example, 10.05 mm or 9.95mm, then the second cutting edge makes chips.
And the right cutting edge automatically stops at a distance of 10 mm from the end of the actual thread and does not finish it.
Sorry, I have been designing cutting tools in Germany for over 20 years - I don't find any functional advantage here.
If I'm wrong, I'd be happy to receive a well-founded explanation.
All these people talking multistart threads. It is just a single start firts cutter does the hard work the second cutter follows behind. In theory it should mean fewer passes but if you look at the screw threads he was not going for finish.. even a rub with a wire brush cleans up and removed burs.
hehe
I am missing the point of the tandem tool bits. What is the purpose of the one closest to the tailstock? If is is set to take a deeper cut than the one to the left then it cannot finish out the cut all the way to the thread runout. Or is this a double lead thread? If so, where do you find a double lead nut?
ну и что гениального ? до конца резец второй не доходит .лучше резцы научись точить ! нормального токаря видно по стружке!
Thread kitne ka hai
Thread size
Your technique very good but your technique multiple thread yes ya no
Ý tưởng điên khùng