Buys stainless exhaust, gets welded with carbon 70s2 wire. Gets mufflers installed, too quite, so cuts holes in exhaust in front of mufflers. I’m scratching my head....
Dood the battery isn’t dying & it didn’t sit too long in your shop it sounds like the guy has an aftermarket cam but didn’t want to spend the money for a tune brah ☹️
The second Vette...the guy wanted more sound...simple take off the damn mufflers. Long tube headers and high flows cats with straights should sound damn good.
Idk if this is why they put the cutouts but the benefit of not doing a muffler delete and just doing those cut outs on the magnaflow is less drone. If you look at a Borla ATAK for the hellcat it is literally a dual straight pipe but mufflers are attached on the side of the straight pipe - most of the exhaust exits straight out not entering through the muffler but some of the gases travel through the side into the muffler and this creates less drone.
I’m normally a flowmaster guy however, that was the worst sounding exhaust possible. That poor guy spent all that money only to have his corvette sound stock. Totally wrong muffler for the application.
On that Magnaflow car, you could've bought the Borla S-type exhaust for far less money and it's louder, wouldn't need the turndowns. Since the Magnaflow was already bought and you wanted it louder, the proper way to do it is to bridge the inlet and outlet pipes, bypassing the muffler. Some of the exhaust bypasses it but some goes through it, and all of the exhaust exits the tips, not under the car. Look up the Z06 stock exhaust mod, lots of guys do that to get more sound and power but retain the factory titanium exhaust.
Buys stainless exhaust, gets welded with carbon 70s2 wire. Gets mufflers installed, too quite, so cuts holes in exhaust in front of mufflers. I’m scratching my head....
right?? just delete the damn mufflers altogether lol
Second that, a grand for a magnaflow exhaust not including installation, ouch!!
The weld also looked terrible…
The 2nd one, no contest.
Dood the battery isn’t dying & it didn’t sit too long in your shop it sounds like the guy has an aftermarket cam but didn’t want to spend the money for a tune brah ☹️
I’d have to say man, you’re a genius for starting this channel..
The second Vette...the guy wanted more sound...simple take off the damn mufflers. Long tube headers and high flows cats with straights should sound damn good.
I have an LS6 with a cam and headers and no cats and 3.5” pipes is sounds absurd
Man you guys do all the cool custom stuff! makes me want to move there and work for you guys! lol
Come on down we’d love to have an eager helper around here.
Nasty, lumpy welds, courtesy of Exhaust Addicts.
Not a fair comparison. Flowmasters in the kit are force II A SOFTER muffler. If he would have put super 10 or outlaw flowmaster would have won.
Should of done the bypass mod instead of the cut outs.
the guy that wanted it louder should just cam it/LT headers /straight pipe it (nocats/nomufflers),if that isn't enough sound for him IDK 😆
Someone give me a link to the manga flow exhaust
Keep practicing your welding.
Looks like someone sneezed on your exhaust. Ohhh wait, it was just your welds......
Both sound good though i think the Magnaflow had a better note to it.
Idk if this is why they put the cutouts but the benefit of not doing a muffler delete and just doing those cut outs on the magnaflow is less drone. If you look at a Borla ATAK for the hellcat it is literally a dual straight pipe but mufflers are attached on the side of the straight pipe - most of the exhaust exits straight out not entering through the muffler but some of the gases travel through the side into the muffler and this creates less drone.
I’m normally a flowmaster guy however, that was the worst sounding exhaust possible. That poor guy spent all that money only to have his corvette sound stock. Totally wrong muffler for the application.
Y'all got any videos with C6 corvette
Basically owner with money vs owner with very little money lol
The flowmaster on the 1st vette sounded soft to me, but the magnaflows sounded better, and I am a flowmaster fan....
SHO/N/OFF / the other one had long tube headers and holes in the Magna flow mufflers which is why it was way louder
Thank you for clearing that up for me, it did make a big difference in the sound...
SHO/N/OFF / I’m a flow master fan as well I prefer them over Magna flow
Corsa extreme for corvettes there is no other option in my book
On that Magnaflow car, you could've bought the Borla S-type exhaust for far less money and it's louder, wouldn't need the turndowns.
Since the Magnaflow was already bought and you wanted it louder, the proper way to do it is to bridge the inlet and outlet pipes, bypassing the muffler. Some of the exhaust bypasses it but some goes through it, and all of the exhaust exits the tips, not under the car. Look up the Z06 stock exhaust mod, lots of guys do that to get more sound and power but retain the factory titanium exhaust.
Flowmaster would’ve sounded a little louder if it also had long tubes on it. Imo. I’m a flowmaster guy
Wait 300 mph on the 2nd vet huh
Thought it was just me 🤣🤣🤣 Tf is wit that
Kph gauge set in mph, must be a Canadian corvette.
all the other gauges are set in metrics. definitely not a us spec
Where you guys located
3560 Dickerson Rd Nashville TN 37207
Yup as expected magniflow yeah buddy
How can you tell with the cutouts? He should have road tested it before/after the cutout mod.
Anybody know the wheels at 4:15
Magnaflow for the win
Shoulda just put fake cut outs on the stock muffler lol, is this a joke?
UA-cam: 1 view, 3 likes
Me: seems right
and im first
Sure not apples to apples !! One with cut outs one without.
You can’t exactly compare two cars with two completely different exhausts 😐
what? thats the point of a comparison...
@@yungtooli No, he was saying the different mufflers not entire exhaust
@@MrFreakyman28 true true
Come on now, they all need more sound
lmao imagine being the first guy. spending all that money just to sound like its stock
omg those welds are atrocious.
Magnaflow is the most overrated exhaust on earth. I’ve never heard one that has any balls.
Putting an x-pipe to replace an h-pipe... 😂 🤮
those welds are horrible… i wouldn’t pay over $20 for those welds