Hello. I have one of your vfd's. Do you have a link to the manuals? I am trying to get it controlled in mach3 and without full manual it is difficult. Thank you.
ua-cam.com/video/7wcC8db4Amg/v-deo.html Настраиваем частотный преобразователь Huanyang GT серии для работы со шпинделем 2,2 кВт. А так же подключаем данный частотник к Mach3 через аналоговый выход. В конце пример 3D обработки на моем станке.
i have 7.5kw VFD that is for this motor to run air compressor and is still little bit struggling to run that compressor start is good but when it comes towards where the compressor should be stoped by pressure switch it slows and want to stop by it self what can be done to fix this so it can run properly. thanx.
Hi, need some help programing VFD HY01D523B to run air compressor motor 3phase 380v 4kw 2900rpm the manual is bit confusing to understand, in Pn12 Motor rating frequency 010.00Hz-and 400.00Hz Default Value Default(3) Default(6) 400Hz-50Hz if i put it to 50Hz its spinning very slow and if i put it to 400Hz it spins very fast motor needs to spin at 2900rpm how can i fix this? thanx.
HY01D523B is 1.5KW 220V VFD. Your motor is 4.0KW 380V. It is wrong to use a 220V VFD to drive a 380V motor. You must use ≥4.0KW 380V VFD to run your motor.
Hello. I have one of your vfd's. Do you have a link to the manuals? I am trying to get it controlled in mach3 and without full manual it is difficult. Thank you.
need help for setup mach3 control spindles speed with GT 7R5g-4
my email : hewgant86@gmail.com
What is correct wiring of switch 1 for 485 operations
There are 485+ and 485- terminals on the motherboard.
Hello. I am very pleased with the purchase of 2.2 kW. But i need your help. Tell me how to connect the inverter to NVEM v2 NOVUSUN
ua-cam.com/video/7wcC8db4Amg/v-deo.html Настраиваем частотный преобразователь Huanyang GT серии для работы со шпинделем 2,2 кВт. А так же подключаем данный частотник к Mach3 через аналоговый выход. В конце пример 3D обработки на моем станке.
i have 7.5kw VFD that is for this motor to run air compressor and is still little bit struggling to run that compressor start is good but when it comes towards where the compressor should be stoped by pressure switch it slows and want to stop by it self what can be done to fix this so it can run properly. thanx.
I can’t understand your meaning, Can you send me a video?My email: service @hy-electrical.com
@@huanyanginverter6516 which is your email? i cant sent email to you
I bought one of your 2.2 VFD. The potentiometer will not adjust rpm on my spindle .
P0.07 = 2，Wiring AI2 GND
sir I have a model GT-4ROG-2 I need the parameters for remote on, off and speed control. thanks
ua-cam.com/video/KD_NrfL7ZZs/v-deo.html
Hi, need some help programing VFD HY01D523B to run air compressor motor 3phase 380v 4kw 2900rpm the manual is bit confusing to understand, in Pn12 Motor rating frequency 010.00Hz-and 400.00Hz Default Value Default(3) Default(6) 400Hz-50Hz if i put it to 50Hz its spinning very slow and if i put it to 400Hz it spins very fast motor needs to spin at 2900rpm how can i fix this? thanx.
HY01D523B is 1.5KW 220V VFD.
Your motor is 4.0KW 380V.
It is wrong to use a 220V VFD to drive a 380V motor.
You must use ≥4.0KW 380V VFD to run your motor.
motor is rated 50Hz
The motor in the video is 50 Hz