Wood lathe restoration
Вставка
- Опубліковано 29 вер 2024
- In this video I am restoring and later renovating an old lathe for wood which I found on the internet.
This lathe was produced by Soviet Union in 1980 and was intended for the school (model STD-120M).
The internet seller assured me that it was in good working condition, but unfortunately it was defective. There were serious electrical issues with it, and a number of mechanical faults.
I spend a lot of time on this project. But in the end the effort has
paid off and I am very happy with the outcome and can now try wood turning.
Узнаю школьный токарный станок по дереву, классные были станки, на них мы учились что-то делать своими руками. Огромное спасибо советским школам, мы многому там научились, а главное быть людьми
A great rebuild. Any way of making it a variable speed? I took note of your electrical skills. That would be the icing on the cake. My first lathe was a Jet midi. You could change speeds with it by changing belt placement. Not great but better than nothing. I’m up to a great old Oliver now. It was made before me and will outlast me and my heirs. It was made in 1943. I was made a couple years later😁😁
СТД 120м узнаю из тысячи!!!!! Красава автор
👍 Это русский станок стд 120 школьник👍👍👍👍👍
The bug is inspecting your work. Well! Very good restoration on that lathe my friend. I,m a carpenter joiner and I do some restoration from time to time. Especially, when I buy a second hand woodworking machines. I,m very fussy on my machines. I love to see them nice and well maintained. Vincent la Valletta malta.
Красиво. Но функционал что до, что после.
Can you tell us some details about the Lathe? Like the swing and bed dimension. Is the motor single or three phase, what HP the motor is? Also can you tell us something about the the pulleys and motor/pulley shaft diameter? I am restoring an older unknown model small wood lathe that was given to me for free. It has no motor needs new bearings in the pulley shaft and the tubular bed rod assembly is missing. Most of the lathe is aluminum except for parts like the tool rest etc. Thanks! Great resto-job BTW.
Это станок из России, производился для учебных завидений, школ в СССР. СТД120.
Я свой тоже восстанавливал! Но выкинул всё лишнее, эл щит, кожух, т к от их вибрации лишний шум. Эл двигателя не было, установил от советской ст машины Эврика-3 на 650ватт. Работает отлично! Переднюю бабку, естественно обильно смазал а на заднюю приспособил враща,ющиеся центр! А теперь служит верой и правдой!
an absolutely superb restoration of an abused and no doubt badly used wood lathe,will give you year's of good useful return,well worth my thumbs up
Отличная работа)))
You are a talented man with many skills and I'm certainly impressed. I look forward to seeing your future projects.
Thank you! Cheers!
عالی درست کردی . آفرین ...
Я, тоже, таким маслом пользуюсь. Нет конкурентов у него))
Very nice! Great job on the lathe and this video. More of the same, please.
Very good restoration, but still it made in Russia, the bench is home made, you should not have put the white lettering on the lathe. Seems to be noisy, Russian....ha ha... Regards and best wishes.
Very nice. I think I would have shimmed the head-stock rather than mill the tail-stock -- but then I don't have a mill or know what all you checked before milling.
Круто! Став як новий! Молодець👍
The beetle approves!
Amazing performance, i loved the military color, thanks.
Nice lathe,,someone loved it to put a vfd on it,,,I love to buy and restore vintage tools,,,have bought 3 wood lathes and 4 metal lathes in the past 4 months,, sold 3 I restored and it payed for all 7..
И станок такой делаю, только ТСД-120. А у Вас СТД-120М
шкільний токарник із трудового навчання, а підшипники ніби гудуть, або сухі, а можливо і замінити потрібно
*What you build always ends up well built and beautiful* which only proves you don't need the best of everything [like this old lathe] *to make an excellent product.*
Buen trabajo y buen equipo de herramientas. Saludos.
I'm restoring an old Delta wood lathe. the motor mounts below on a hinge. Do you think the weight of the motor is enough to make the belts work or does the motor need to be locked in position?
СТД120М центра не сошлись потому что задняя бабка не родная
клас клас классссс
Sir, great work and thank you for sharing 🇵🇷👍👍👍👍👍🇵🇷
Fantastic Job hope it does some great turning for you, have a nice day, Brian UK !!!
Muito bom 👍, forte abraço de nós do CANAL FERREIRA MOTOS
Até o besouro foi conferir se o Serviço ficou ótimo. Parabéns pelo belo trabalho quê fez e ficou Nota 10.
Aku bikin rangka mesin bubut sendiri dari kayu
Sir ye मशीन कितने की बनेगी mujhe bhi banbana h me mp se hu
Від усіх Ваших відео йде масса позитиву. Дякую , і щоб вистачало оптимізму і бажання.
Дуже дякую, за цей коментар! )
How is it that the tail stock was hitting high in relation to the head stock? I would think that wear would cause the tail stock to register low, and not high.
Headstock from a different lathe is my guess.
Если судить по пускателю, то станок из СССР. Удачи!!!
Спасибо, так и есть, ето школьний станок.
Одни словом "красавчик"!!!
Simonov Artem Russia Спасибо!)
Супер , осталось потренироваться в использовании резцов )
Отлично получилось! Имею такого же школьника, ждёт своего часа на восстановление, а тут такое отличное видео выложили. Обязательно учту при восстановлении своего
Спасибо!)
Very nice up grade on the wiring. That is an unusual drive center, for my part of the world. I'm offering this as help, not criticism! All the dowels you put in, did provide alignment but did not add strength. So you could have used a lot fewer. A proper glue joint is stronger than the wood. The mitered frame around a solid wood center will likely fail in the corners if the moisture content changes. The batten on the bottom side would have been better had you provided slots & washers to allow for the inevitable wood movement. I hope they don't split the nicely done wood. The reason is that wood moves very little in length but quite a lot in width, with changes in moisture. Winter to summer conditions will cause the changes in moisture, even if you put finish on the wood. Happy turning.
Fine work not just in restoration but as well in beauty. This video would be very useful as a teaching aid. You are to be praised for your talent, patience, and eye for the intrinsic as well as the functional value of this tool.....excellent effort! Greetings from Kauai.
Great work, bravo. The bug was helping you this whole time? :)
Thank you. I had couple of them, I like these bugs, these weeks they are everywere and they bring me nice mood! :)
For ''hobbyist'' you have an amazingly well equipped workshop.!
Вы и это можете делать!!!
Разобрать пожалуй любой может. Но вот как всё на место поставить, да ещё и правильно!
ТАЛАНТИЩЕ! 👍💝👏💮
I put treadmill motors on all my lathes,,unbelievable power and so smooth and quiet, and the soft start is so much easier on the lathe
Очень круто. Золотые руки
beautiful machine, bud! very nicely done.
найс джоб
Отличная работа, вторая жизнь
Спасибо! )
Beautiful job. Looks like brand new. Wish I had it myself.
В ел.шкафу коли купував станок таки була пуста чекушка чи ні?)))
Лайк за відео, ще один апарат став у стрій, респект!!!
центр в передней бабке болгаркой на максимальных оборотах станка выправить можно, заготовку бить перестанет.
Very good.
Nice work. With all that power that machine will never bog down.
КЛАСС! Станок,наверное и с новья таким не был крассивым!
Nice
Станочок вийшов добрий,як для себе... а жук першим прилетів обісрати(жарт) :)
and the video comes to a full circle..great editing......and really liked the electrical sorting...
very good but your motor driver must be...for motor velocity.
Beautiful! How do you pay your Q.A. inspector?
On the 17th minute where you take all the old contactors and terminals out, there was what I believe a rectifier on the bottom right corner. Which is a diode, so the power can't travel back when shutting off the lathe. Or if it is more than one of these - it could be used to convert AC to DC or act as a soft start of sorts. You did not put it back. Do you think it is not needed or maybe you had a schematics to see what circuit was it in?
Anyway, beautiful work. Privet iz Litvi.
На старых контакторах была реализована схема электродинамического тормоза. Это быстрый останов двигателя после отключения.
Awesome job...! I will like to know where can I get the stamp than you are using to put you brand ? Thank you
Thank you. This hot stamp was made for me at one of the factories in my city.
color shit!!!!
That was great! It reminded me of Hand Tool Rescue! (Nice beetle, too.) Question: were you worried at all about lead in the paint you were stripping? Thanks very much for sharing this.
Thank you sir, I didn't know about lead in the paint.I wore a mask. Next time I'll better think about safety.
superb dude it would be a shame to get it dirty brilliant
Great job, and the video was excellent also...
Great job keep those videos coming love learning new things
How many prices for lath machine
Well done ,Greetings from Hong Kong
Thank you from Ukraine! :)
O
@@homemadeinlviv8041s
A nice Job !!!!!
Very nice
Great restoration of that old lathe (and good turning demonstration). Does the lathe have a noisy bearing, or is the sound from the belt drive? I like the insect at the end!
Stanley Thigpen. I agree. Sumpin ain’t right. That lathe is way too noisy. He never showed taking the headstock apart, so we don’t know if it has ball bearings or plain bushings. If ball bearings, they are really worn or need lube.
If bushings they need replacing. Maybe it’s the motor bearings? Also, all of that sheet metal around the pulley assembly amplifies any noise. Remember this is a low end Russian lathe.
how you change the motor of 3kw to 1 kW ?
Beautiful work!!! Greetings from Italy 👍 👍 👍
Thanks from Ukraine! :)
Классный станочек если можно скажите марку станка
Awesome job !!! Great videos.
Mantep pak de
THE BEST!
а почему базу не удлинил ? 50 см маловато
Beautiful work and tool.
Brilliant work mate, well done.
What kind of bug is that?
Double Dare Fan May-bug
fijn job,grtn uit schoten
ДИЗ.
В конец появился майский жук, принять работу.
Artur Ciubotaru да проверил все размеры
so much satisfied to watch this
Show! :) \o/
Great restoration - as always 👍👍👍
Love ot doing a good job mate.
Outstanding restoration.
Very good keep it up man :)
Wow a lot of pieces.
super
very nice. does it only run at 1 speed?
Thanks, there are two speeds
У нас в школе такие были
Very nice job!
Muy buen trabajo
very nice video
Awesome👋👋👋💪💪💪
Хороша робота .