I had to lengthen the charge lead on 1 bank as my cranking battery is aft and TM batteries are under the bow. NOCO states you must cut and splice after the in line fuse and use the original terminals to the battery.I also used 8 Gauge wire and heat shrink butt connectors for the extension.It is working well and no issues. Liked your layout and install...
If they are run in series you would need a 24v charger to charger them with one charger. The charger would connect at opposite ends of the series. If ran in parallel you can use a 12v charger but may take additional time to charge based on the chargers capacity. I would recommend just getting the dual charger. So you know the condition and charger status of each battery.
I wouldn't know the answer to that question. I've never messed with solar panels before. I'd imagine from what I know of them you'd need a ton of large panels to supply enough power to the battery to actually be beneficial.
My genius gen 2 went out and doesn’t charge two of the the four banks. Only had it a little over a year. I saw reviews and they said that it’s a common problem with that model. Like you said in your video it’s plug and play with no buttons or options. So after watching your video I’m gonna get the GenPro as well to replace that one. How do you like it so far that new charger.
@@InfiniteBassin my tilt trim motor and off and on switch on my foot pedal went out. Now this bank charger. I’m still waiting on the trim motor from mercury through my warranty by BPS. It’s been 7 months without fishing. My boats just sitting doing nothing. Sucks Asss. Mercury said the part is backed ordered. Oh well all I can do is wait since it’s warranty related. I’m like i only had this boat less than a year and the tilt trim went out. 😬
@@chino0119 dang man hopefully it comes in soon. The on/off switch, is it for an ultrex. I know minnkota upgraded those switches a while back so you might be able to get a new one free.
I Have the Gen 5X2 with 2 AGM batteries. Can I connect the negs of each battery together? The charger doesnt seem to connect the negs internally thru the charger is why I am asking. I am using battery isolator where the grounds would be connected together.
What are you using the batteries for trolling motor or electronic? 12v or 24v? That charger on each connection will have a black (negative) and red Positive.
Still a newbie but am deploying for a couple of months and was told to install this to my boat battery so that it wouldn’t lose its charge. Do I just connect this onto the battery? Battery is new. Not sure if I’m supposed to charge this charger first before connecting to battery. Thanks.
These chargers aren't battery packs you charge before use. These are the chargers. All you do is install in boat and connect to batteries. When done connect to an external plug in. The onboard charger will charge your batteries to full, then trickle charge them off and on to maintain a full charge.
@@InfiniteBassin so even if battery is already fully charged, I still need to external plug to an outlet? Or can I just connect charger to boat battery and leave it? Thanks!
@@larrycelzo2028 yes it needs to be plugged in. If you don't plug it in to an external plug the charger won't work and the battery will drain and die over time. Those on-board chargers only work when plugged into an external plug.
The warranty process was super easy. I payed to ship the old one to them if I remember right. That's all I payed for once they got it, I had the new one in less than a week.
I ended up buying another one cause I didn't want to wait. The new one showed up to the house the next day while I waited on the new one back from warranty. All and all it maybe took 2 weeks from the time I sent the old one off until I got the new warranty one home.
The simple answer is yes you can, it will charge your battery almost twice as fast. On the other hand you need to know your batteries charge current rating to make sure you aren't exceeding that. If using it on a lead acid battery check the fluid level frequently because higher charging currents can evaporate fluids faster than lower currents. Also check the battery temp while charging to make sure the battery isn't over heating.
Yes. When the batteries are fully charged the charger will go into a trickle mode. That will maintain the full charge on the battery and not over charge them.
Nice Video. The question, Got the 5x3 on mine. 2 Deep cycles 29's and a 27 crank. When it's plugged at the marina the unit works, then when unplugged from the AC it's off while the boat is out. It works without being on (no lights)? I've noticed one of my batteries isn't holding a charge, while the other ones seem fine. Bought a new one today to replace the one, hopefully, it works. Thanks in advance!
No. They only work when plugged into AC wall power. So when out on the water it's not charging your batteries at all. The only thing that gets charged is the starter battery and thats from the alternator on the engine. The trolling motor batteries only charge when the onboard charger is plugged into an external AC source. The name onboard charger simple mean its a charger thats in your boat.
@@InfiniteBassin Thanks for the quick reply. Isn't it supposed to trickle charge to keep the power circulating to all batteries? I feel like I'm missing the point of this thing. I have 3 in total. one 27 for the crank, 29 for the internals (navs/Bildge, etc) and a 29 for the fun stuff (Leds, water pump, Air Horn, etc).
@@bnyc5985 you're welcome and nope it doesn't. When plugged into an external power source they become fully charged the charger will go into a trickle mode. That prevents then from being over charged when the boat is not in use. It's a convenient way to charge 3 batteries at the same time and have them charged properly with 1 power cord. These charged don't do anything while not plugged in. The powerpole charger is one that is customizable for on the water options but not these.
If you look toward that part of the video is connects to the quick connect that goes through the hull. It allows you to connect your extension cord to the boat externally so you don't have to climb into your rear compartment to find the charge cord.
Sounds like you've got yourself a Lemon that needs to be replaced or you are doing something wrong with it. I've had no issues with this charger since this video. What is the reason you've sent it back 3 times for?
I just bought my first bass boat and got the Noco charger. I appreciate the video! Definitely helpful! Thanks!
I had to lengthen the charge lead on 1 bank as my cranking battery is aft and TM batteries are under the bow. NOCO states you must cut and splice after the in line fuse and use the original terminals to the battery.I also used 8 Gauge wire and heat shrink butt connectors for the extension.It is working well and no issues. Liked your layout and install...
I just ordered one from Amazon, your video was helpful. Thanks !
sweet garage set up , everything is organized and clean. Just got Nolo charger for my boat so this helped, thanks.
Thanks man I try to keep it that way. I don't like for things to be a mess. You'll love the charger I've been happy with it so far.
Good show
where you not supposed to unscrew the lead battery screws at the top to help it breath? just curios
does the charger battery selection mode stay selected after you unplug it then plug it back in?
Yes it stays connected.
If I’ve got two batteries connected together do I still use a novo dual battery charger or will a single unit charge both batteries?
If they are run in series you would need a 24v charger to charger them with one charger. The charger would connect at opposite ends of the series. If ran in parallel you can use a 12v charger but may take additional time to charge based on the chargers capacity. I would recommend just getting the dual charger. So you know the condition and charger status of each battery.
Can you have a solar controller on the batteries simultaneously? Getting charge from your solar panels? Or is it one or the other?
I wouldn't know the answer to that question. I've never messed with solar panels before. I'd imagine from what I know of them you'd need a ton of large panels to supply enough power to the battery to actually be beneficial.
Good video, much appreciated. Curious how long the battery connection cables are? 72" or so?
Thanks and I'm not sure how long they are I didn't measure them before installing.
Yes
My genius gen 2 went out and doesn’t charge two of the the four banks. Only had it a little over a year. I saw reviews and they said that it’s a common problem with that model. Like you said in your video it’s plug and play with no buttons or options. So after watching your video I’m gonna get the GenPro as well to replace that one. How do you like it so far that new charger.
That sucks, it's always something with these boats. So far it's been good I don't have any complaints.
@@InfiniteBassin my tilt trim motor and off and on switch on my foot pedal went out. Now this bank charger. I’m still waiting on the trim motor from mercury through my warranty by BPS. It’s been 7 months without fishing. My boats just sitting doing nothing. Sucks Asss. Mercury said the part is backed ordered. Oh well all I can do is wait since it’s warranty related. I’m like i only had this boat less than a year and the tilt trim went out. 😬
@@chino0119 dang man hopefully it comes in soon. The on/off switch, is it for an ultrex. I know minnkota upgraded those switches a while back so you might be able to get a new one free.
@@InfiniteBassin yes on the ultrex. That their number one issue they have is the switch going out. It’s a cheap fix.
@@chino0119 mine had been the plastic bushings on mine. I've replaced them twice already. Got spare bushings on the wall now.
Great vid probably a senseless question but I’ll be running 2 LiFePO4 12v in series for my Ulterra can I use the Noco 5x2 charger in the set up
I Have the Gen 5X2 with 2 AGM batteries. Can I connect the negs of each battery together? The charger doesnt seem to connect the negs internally thru the charger is why I am asking. I am using battery isolator where the grounds would be connected together.
What are you using the batteries for trolling motor or electronic? 12v or 24v? That charger on each connection will have a black (negative) and red Positive.
Still a newbie but am deploying for a couple of months and was told to install this to my boat battery so that it wouldn’t lose its charge. Do I just connect this onto the battery? Battery is new. Not sure if I’m supposed to charge this charger first before connecting to battery. Thanks.
These chargers aren't battery packs you charge before use. These are the chargers. All you do is install in boat and connect to batteries. When done connect to an external plug in. The onboard charger will charge your batteries to full, then trickle charge them off and on to maintain a full charge.
@@InfiniteBassin so even if battery is already fully charged, I still need to external plug to an outlet? Or can I just connect charger to boat battery and leave it? Thanks!
@@larrycelzo2028 yes it needs to be plugged in. If you don't plug it in to an external plug the charger won't work and the battery will drain and die over time. Those on-board chargers only work when plugged into an external plug.
Good luck with the warrant - they make you pay shipping and if it’s 2 years you also pay $133 for a replacement
The warranty process was super easy. I payed to ship the old one to them if I remember right. That's all I payed for once they got it, I had the new one in less than a week.
I ended up buying another one cause I didn't want to wait. The new one showed up to the house the next day while I waited on the new one back from warranty. All and all it maybe took 2 weeks from the time I sent the old one off until I got the new warranty one home.
That battery compartment looks way to clean.
Hahaha. I trying to keep it that way lol
Can I parallel/join 2 of the 3 ports for higher charging current?
The simple answer is yes you can, it will charge your battery almost twice as fast. On the other hand you need to know your batteries charge current rating to make sure you aren't exceeding that. If using it on a lead acid battery check the fluid level frequently because higher charging currents can evaporate fluids faster than lower currents. Also check the battery temp while charging to make sure the battery isn't over heating.
So after a year or so how would you rate it’s performance?
For the time that I used it the charger worked great with no issues. A sponsor upgraded me to the Powerpole Charger so now I'm running that.
Do you leave NOCO plug in even after battery are fully charged?
Yes. When the batteries are fully charged the charger will go into a trickle mode. That will maintain the full charge on the battery and not over charge them.
Thank you !!
@@jkroblox9723 you're welcome
Nice Video. The question, Got the 5x3 on mine. 2 Deep cycles 29's and a 27 crank. When it's plugged at the marina the unit works, then when unplugged from the AC it's off while the boat is out. It works without being on (no lights)?
I've noticed one of my batteries isn't holding a charge, while the other ones seem fine. Bought a new one today to replace the one, hopefully, it works.
Thanks in advance!
No. They only work when plugged into AC wall power. So when out on the water it's not charging your batteries at all. The only thing that gets charged is the starter battery and thats from the alternator on the engine. The trolling motor batteries only charge when the onboard charger is plugged into an external AC source. The name onboard charger simple mean its a charger thats in your boat.
@@InfiniteBassin Thanks for the quick reply. Isn't it supposed to trickle charge to keep the power circulating to all batteries? I feel like I'm missing the point of this thing. I have 3 in total. one 27 for the crank, 29 for the internals (navs/Bildge, etc) and a 29 for the fun stuff (Leds, water pump, Air Horn, etc).
@@bnyc5985 you're welcome and nope it doesn't. When plugged into an external power source they become fully charged the charger will go into a trickle mode. That prevents then from being over charged when the boat is not in use. It's a convenient way to charge 3 batteries at the same time and have them charged properly with 1 power cord. These charged don't do anything while not plugged in. The powerpole charger is one that is customizable for on the water options but not these.
@@InfiniteBassin Great to know. Thank You again!
@@bnyc5985 you're welcome glad I could help
Does this charger need to be vented
No it doesn't.
What does the 3 prong plug connection do? AKA the ac connection
If you look toward that part of the video is connects to the quick connect that goes through the hull. It allows you to connect your extension cord to the boat externally so you don't have to climb into your rear compartment to find the charge cord.
@@InfiniteBassin Oh i see i just gotta boat with an ac cord out by the charger figured out its just for plugging in from the wall
@@Brobro449 what boat did you get? Yep thats all it's for.
@@InfiniteBassin 2002 lund all sport adventure 1675. Its the white with red decal
@@Brobro449 niiice that should be a really good boat for you.
I run a three channel Noco genius
Nice is that the only brand you've used?
@@InfiniteBassin yes sir, zero problem so far. It's been in the boat for two years now.
@@richarddedmon4651 nice thats how long mine lasted before it started having issues.
Does the alternator affect the charger at all?
@@timmoore6656 no it doesn't.
I have a genius pro 4 bank,I have sent it back for replacement 3 times.i don't recommend this.go with a minn kota
Sounds like you've got yourself a Lemon that needs to be replaced or you are doing something wrong with it. I've had no issues with this charger since this video. What is the reason you've sent it back 3 times for?