PAS 1 is what i would like PAS 2 or 3 to be like. Is there a way to get it to give less power in PAS 1? I tried adjusting 11 PAS sensitivity with no noticeable effect. Also tried adjusting 12 PAS strength with no noticeable effect. I want the option to get a better workout and extend the battery at the same time. If i try to pedal harder to get a workout the bike just gives more power. Great for off-roading and trails, but not so great when cruising on flat pavement. In P-setting 11 is 01-or 24 more sensitive? In P-setting #12 is 00 or 5 more assist from the motor?
Hi, Unlock the speed limiter! 1, Turn on the display. 2, Press and hold the "+-" buttons simultaneously for 3 seconds to access the configuration interface. 3, Release the "+-" buttons and then press and hold the "+" button for 15 seconds to remove the 6 km/h acceleration limit and the 25 km/h speed limit. Since the screen is the latest version, the method for releasing the speed limit is different from previous versions.
I Can't get throttle only is P-setting 10. 00,01,02 all give pedal assist. Also can't figure out how to get cruise control to work, if it actually has it?
Hello, please reply. I only use it on the pedal. The throttle button does not work. I turned it on from the settings and it did not work. I looked at the electrical tape file at the battery. Everything is fine. What is the solution? I ask for your help. The dealer from whom I bought it did not respond to me.😢😢
@@plantedit Thank you for your response, but I did not understand how it works. Could you please explain to me how to operate the throttle button? 😪😪😓😤
I had to enable it on mine by holding down the throttle and right brake lever then turning on the bike. I kept them held down for 10+ seconds then released and turned the bike off and on.
Q: When unlocked, what is the top speed available using *throttle only* (i.e. no-pedal)?
Some reviews say *20mph* others *28mph* ??
I cannot get my throttle to work at all please help
Thanks for the run-down - been looking for these for a couple of weeks!
More confused!🤣 Thought I knew by watching EBike Review Adventures, which goes through entire e-bikes. Started out pretty good. 🚴
Sir my cycle battery is full but display showing always charge battery same like this cycle
Settings are pretty lacking compared to older models
Первое такое видео на новинку. Очень ждал вас. Уже 300 км на нем накатал и теперь я властелин свободы благодаря вам. Спасибо.
Hi , is there an option to change the amount of assistance at different PAS levels ?
There dosent seem to be as far as I can tell. Unlike the ep2 pro.
PAS 1 is what i would like PAS 2 or 3 to be like. Is there a way to get it to give less power in PAS 1? I tried adjusting 11 PAS sensitivity with no noticeable effect. Also tried adjusting 12 PAS strength with no noticeable effect. I want the option to get a better workout and extend the battery at the same time. If i try to pedal harder to get a workout the bike just gives more power. Great for off-roading and trails, but not so great when cruising on flat pavement. In P-setting 11 is 01-or 24 more sensitive? In P-setting #12 is 00 or 5 more assist from the motor?
Hi, Unlock the speed limiter!
1, Turn on the display.
2, Press and hold the "+-" buttons simultaneously for 3 seconds to access the configuration interface.
3, Release the "+-" buttons and then press and hold the "+" button for 15 seconds to remove the 6 km/h acceleration limit and the 25 km/h speed limit.
Since the screen is the latest version, the method for releasing the speed limit is different from previous versions.
very confusing - not really helping
or you're just slow
that might be right - so it’s confusing in my slowness
I Can't get throttle only is P-setting 10. 00,01,02 all give pedal assist. Also can't figure out how to get cruise control to work, if it actually has it?
Not tested this yet but after setting 17p to 01 you apparently hold down - for a few seconds while riding for cruise control
My fully electric doesn’t work, how can I change it?
Plz help me for cycle battery display fault if any buddy know plz tell me
Buschada r5 pro same menu and the same code error
Come va? Ho acquistato e aspetto la consegna
Hello, please reply. I only use it on the pedal. The throttle button does not work. I turned it on from the settings and it did not work. I looked at the electrical tape file at the battery. Everything is fine. What is the solution? I ask for your help. The dealer from whom I bought it did not respond to me.😢😢
Is it possible the display setting didn't record the choice? It's only one of three settings then power off. Good luck to you.
@@plantedit Thank you for your response, but I did not understand how it works. Could you please explain to me how to operate the throttle button? 😪😪😓😤
set 010 from 0 to 2
I had to enable it on mine by holding down the throttle and right brake lever then turning on the bike. I kept them held down for 10+ seconds then released and turned the bike off and on.
You said save it. How??
press and hold info button...
P 15 P16 this is?
how to make the settings default
set to the values from manual
hold the + button and light button down, then use the + to change no to yes then hold the switch button down and it will reset to defualt.
Can you unlock full throttle to 28mph
No max 20mph
Yes first check if it says -6 on back of display, then go into settings and hold + for 15 seconds
@@onaroad2riches736Does this unlock throttle-only to 28mp/h?
@@cortex2476 yes
unlock speed is p08... can be set to anything you like