there are cell spacers very cheaply on various sales platforms. they better than gluing batteries together and safer too. also grade your cells, don't mix a 1.5AH and say a 1.2AH cell if you using reclaimed batteries
I made an ups with 3s 25a BMS and 6cells of 18650. My router supports 12v 1.5amp. Can I use a 12v 5amp adapter to charge the ups alongside to power the router. 5a-1.5a=3.5amp for my 3s battery pack (6*18650 batteries total (🔋🔋+🔋🔋+🔋🔋)) Is it alright to use 12v 5a charger? Is it going to quickly reduce the battery lifespan?
Do I need to connect (weld, solder) batteries to the BMS board in sequence (from plus to minus or vice versa) how is it in the laptop battery so that the board does not go into protection?
Your video title has a critical error. the 12.6v is correct but you used a comma instead of a period leading me to believe you somehow had a pack that could output both 12 volts and 6 volts. I figured that out after watching your video.
Does the final outlet (black and yellow wires) account for charging and discharging? I see other BMS systems have a separate charge and discharge ports. I plan to use a 6s BMS to do a blue tooth speaker build with a 24 volt power supply. How many 18650 batteries should I use?
Hi DIY Lady, you are great, can you tell me which adapter you use to load the 6 pack?. And for a 3-pack which adapter do you need? Thank you from Italy
@@diylady Now I see, there is a comma in 12,6 volt whereas it should have been a period as in 12.6 volts. Now I see why this did not show how to build a 6 volt replacement pack.
Everything is fine; I request you to highlight the following: 1. How long the charger has to be connected with the battery pack? 2. Is there any indication about the battery is fully charged?. Please clarify. Video is nice one to be tried.
This might be a silly observation, but can you confirm that what I am seeing is 3S2P configuration - two sets of (18650) in series and in parallel to up the capacity?
Do you make up battery packs to sell? I need a 6v, 15Ah pack for charging with a 10 watt solar panel. I could put a buck converter on the end to get it down to 6v if necessary. Or, can you provide a circuit diagram for such? Thanks Mike
This is for use on a game cameras. Almost all use 6v. I saw some LiFePo4 on eBay, 3.2v, 6500mAH. 6.4v would not hurt any game camera. 3600mAh will last 2 months in most game cameras. I leave mine unattended for like 6 months. I think if one diode protected each bank and regulated the solar panel to 6.4v you could run direct off the solar panel. 0.5 amp is the best a 10 watt panel will do in bright sun. I just subscribed!
Thanks, this video was very helpful as I recently was given 9 18650 battery's. What is the highest charging voltage you would recommend? I have a 12v 2a plug, should that be alright?
If i use 6 batteries i Will have more capacity ? Because i making bluetooth speaker 2*100w and i dont know how many batteries i need to use for 5-6+ hours of play time please help me 🙏
In the video, your spotlight video on batteries is in the foreground rather than the narration... You passed even the plus and minus connections of the batteries quickly.. Oh, you can share the connection photo or the plan.
I made a charger out of 4 18650 batteries. Then used 4s 40A charging board from aliexpress and did the circuit as said. After leaving it to charge overnight i can see the charge has only come 11.1v where as i was expecting it to have 16.4v. Also the charge lasted for 5 mins only any reason why?
Oh. The first : you shoudn’t charge it over night , second : have you test your battery ? It’s new or that you take it from laptop battery ..? And the third : your charging is not work any more , it’s broken ...
Hello love you video do you have any video. Of building a 36 volt 12 amp. if you do please let me know or share this with me or if you have any diagram would help me to Bill mine would greatly appreciate it thank you very much
@@stefanmerk5750 This kind of BMS have included over charge protection, balancer, under voltage protection . Thats why you only need an 12v adapter charger.
Do it yourself with a junk pc power suply (atx power supply), its veri easy, and you can get 3v, 5v, 12v, even 24 v from it. But for charging this bms you need a 12.6 v, so get an extra dc-dc up voltage, to increase the 12v to 12.6 v from your atx pc power supply modificated. Check some videos of how to transform a pc power supply for getting 12v (and others). Hoppe i help you.
![[UA] NAVI vs MOUZ | BO5 | IEM Rio 2024](http://i.ytimg.com/vi/CMBYk0cbGoA/mqdefault.jpg)
there are cell spacers very cheaply on various sales platforms. they better than gluing batteries together and safer too. also grade your cells, don't mix a 1.5AH and say a 1.2AH cell if you using reclaimed batteries
this video is best one so far...thanks for your work..
I made an ups with 3s 25a BMS and 6cells of 18650. My router supports 12v 1.5amp. Can I use a 12v 5amp adapter to charge the ups alongside to power the router.
5a-1.5a=3.5amp for my 3s battery pack (6*18650 batteries total (🔋🔋+🔋🔋+🔋🔋))
Is it alright to use 12v 5a charger? Is it going to quickly reduce the battery lifespan?
c'est magnifique merci beaucoup pour le conseil de branchement 👍👍✌👐
Do I need to connect (weld, solder) batteries to the BMS board in sequence (from plus to minus or vice versa) how is it in the laptop battery so that the board does not go into protection?
I'd like to see how you made your spot welder, but I have yet to look at what other videos you have, so I hope to be pleasantly surprised.
Where to buy this kind of bms?
This dc jack should not be connected directly to the bms because it will give reverse charging you should connect with a diode 👍
the battery pack voltage is 12.6v if u set the charger voltage to the same voltage there will be no reverse charge
I want to ask you something. Is it normal for the resistor on the BMS to heat up when the battery is being soldered to it?
Nice 👍🏻👍🏻 🇮🇳 Kuki 03|06|2022.
Your video title has a critical error. the 12.6v is correct but you used a comma instead of a period leading me to believe you somehow had a pack that could output both 12 volts and 6 volts. I figured that out after watching your video.
Does the final outlet (black and yellow wires) account for charging and discharging? I see other BMS systems have a separate charge and discharge ports. I plan to use a 6s BMS to do a blue tooth speaker build with a 24 volt power supply. How many 18650 batteries should I use?
On 6S BMS will have an port for charging and one for discharge. You can use 6 or 12 batteries for this…
Hi DIY Lady, you are great, can you tell me which adapter you use to load the 6 pack?. And for a 3-pack which adapter do you need? Thank you from Italy
You need 25.2 vol adapter for 6S batterry pack , and 12,6vol adapter for 3S battery pack
@@diylady Thanks for the information! You are fantastic, continue making videos, I will always follow you. Cheers!
@@diylady Now I see, there is a comma in 12,6 volt whereas it should have been a period as in 12.6 volts. Now I see why this did not show how to build a 6 volt replacement pack.
Hi Lady, I have an old drill that worked with 14.4volts ni-cd pack.
You think this pack is powerful enough to make it work with my drill?
You should make 4S pack for 14,4 volt.
Can you make a video how to put battery indicator meter for level of charge and discharge? Thnk you✌️🙂
Everything is fine; I request you to highlight the following:
1. How long the charger has to be connected with the battery pack?
2. Is there any indication about the battery is fully charged?.
Please clarify. Video is nice one to be tried.
Why do all the DIY channels feel the need of putting horrible music on their videos? I mean is this mandatory?
This might be a silly observation, but can you confirm that what I am seeing is 3S2P configuration - two sets of (18650) in series and in parallel to up the capacity?
Or good for drone builds
Sir it can be that 12.6v 25a battery pack into 12v DC 150 watts?
Input and ouput same wire? Charge on same wire?
Yas
Do you make up battery packs to sell?
I need a 6v, 15Ah pack for charging with a 10 watt solar panel. I could put a buck converter on the end to get it down to 6v if necessary.
Or, can you provide a circuit diagram for such?
Thanks
Mike
Sorry but i have not do it before , i’ll try it as soon as i can, and i’ll up it on my channel.
This is for use on a game cameras. Almost all use 6v. I saw some LiFePo4 on eBay, 3.2v, 6500mAH. 6.4v would not hurt any game camera. 3600mAh will last 2 months in most game cameras. I leave mine unattended for like 6 months. I think if one diode protected each bank and regulated the solar panel to 6.4v you could run direct off the solar panel. 0.5 amp is the best a 10 watt panel will do in bright sun. I just subscribed!
And can i use a 22 awg wire for wiring in battery and bms?
Thanks, this video was very helpful as I recently was given 9 18650 battery's. What is the highest charging voltage you would recommend? I have a 12v 2a plug, should that be alright?
if you link 3 together in series then 12.5 to 13.6....please using a proper bms and don't just connect 12V to it.
If i use 6 batteries i Will have more capacity ? Because i making bluetooth speaker 2*100w and i dont know how many batteries i need to use for 5-6+ hours of play time please help me 🙏
You must use at least 9-12 batteries to pair 1 pack of 3S batteries
@@diylady and if i buy 6 batteries for 6s bms Board ?
You cannot use BMS as a cell charger, you need a charging module.
How many hours charging battery ms lady
Kenapa kepala charger saya panas banget? Kalo batre nya hanya hangat biasa
DIY lady how much mah in your 3S 2pack battery?
You're awesome lady .Where are you from? Perhaps we can make a joint venture to develop a product for the US market.
In the video, your spotlight video on batteries is in the foreground rather than the narration... You passed even the plus and minus connections of the batteries quickly.. Oh, you can share the connection photo or the plan.
Tốt lắm cô gái!
thanks bạn đã động viên. hi
How to charging voltage your battery
Şiir gibi montaj olmuş helal olsun
what model of battery is this?
Beautiful 👏👏👏👏
Wait a minute this board is named 3s so you must use only 3 batteries ? Or ? If i do this like you i Will have better capacity ?
i use 3S with 2 pack battery ..
@@diylady if i do same like you i Will have better capacity ?
pin nay chạy dc moto k bác để e thay vào moto quạt ạ
What's bms battery charging the 5v micro USB charger?
Mai is bms battery ko 5v micro USB charger se charge kar sakta hu kya?
Thought this was going to be how to build a 6vdc battery pack however it looks to be a 12 volt pack.
12.6 volts dc not 6 volts dc
How many amps are there?
12v motor how many hours it will run bro...
Can I use 40 amps bms on my 20 amps battery pack?
Suryakantaraychoudhury Choudhury yês ofcourse you can
No
Please list of materials and where did you buy greetings from Mexico
i'm sorry but can you buy it from aliexpress ?
I made a charger out of 4 18650 batteries. Then used 4s 40A charging board from aliexpress and did the circuit as said. After leaving it to charge overnight i can see the charge has only come 11.1v where as i was expecting it to have 16.4v. Also the charge lasted for 5 mins only any reason why?
Oh. The first : you shoudn’t charge it over night , second : have you test your battery ? It’s new or that you take it from laptop battery ..? And the third : your charging is not work any more , it’s broken ...
DIY Lady how do you know that the bettry is full or it needs charging ???
Hello love you video do you have any video. Of building a 36 volt 12 amp. if you do please let me know or share this with me or if you have any diagram would help me to Bill mine would greatly appreciate it thank you very much
Como eu ligo 6 celulas sem a placa BMS?
How many A you battery?
I need a 9s bms can I make it by making 3*3s bms in series?
Que cargador usas?
How to know if the battery is fully charge
Thank you
how do you charge this typ of BMS 3S2P?
By using adaptor
@@madinnovationandcreation5650 please show me an example
@@stefanmerk5750 This kind of BMS have included over charge protection, balancer, under voltage protection . Thats why you only need an 12v adapter charger.
Give the details and required iteme
Why are you using a 12v - 25A BMS for this pack? It's way too overkill for such a small pack.
Why do'nt you tell us what the amprage is that this BMS (BS) can handle ?
It's write on the BMS pcb - 25A!!!
Cut that bloody music 🎧😫 nice job though
Cho giá bao nhieu 1cuc bin bạn làm đó bạn ơi
Mình chỉ làm dùng chứ k bán bạn ơi
Sona
👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼
Where can I find the thing can charge the battery???
Link please 😢😢😢
Do it yourself with a junk pc power suply (atx power supply), its veri easy, and you can get 3v, 5v, 12v, even 24 v from it. But for charging this bms you need a 12.6 v, so get an extra dc-dc up voltage, to increase the 12v to 12.6 v from your atx pc power supply modificated.
Check some videos of how to transform a pc power supply for getting 12v (and others).
Hoppe i help you.
Buenas tardes, ayudaría mucho el diagrama del batería pack.
Charging power ratting share
like
😚👍😚👍
Oke
please link pcb,tanks bye bye italy
Ji back up
Sis. i am not seen any nail polish 😀😜