Building an X-Carve Folding Table
Вставка
- Опубліковано 7 тра 2019
- With my X-Carve taking up every square inch of my workbench, I needed to do something and fast. In this video, I do that something and build a foldable table for my X-Carve. I hope to have plans up for this soon, but nothing as of now. Follow along!
Relevant Links:
Inspiration drawn from Targ's build here - discuss.inventables.com/t/tar...
Inventables X-Carve - www.inventables.com/technolog...
Tools used in this video:
Ridgid R4512 Table Saw - amzn.to/2Itoy2b
Dewalt Drill Driver/Impact combo set - amzn.to/2VYGJUV - Навчання та стиль
You can find a cut list for this project in the following link. Note this is not a full set of plans, just the dimensions for each cut in the project. dura.works/plans/xcarve-folding-table-cut-list.pdf
Your cut list is a HUGE help. There is one additional measurement that would be most helpful. Can you share the size of the holes and exact center measurements for the pivot point on the two sides please? It appears that the holes are 12-3/8 back on the torsion top. Would you agree? Thank you!
@@DonG-xn2lu On the torsion box, the holes are drilled 13 5/8" down the back. On the sides they are 1" down from the top, and 2 1/2" in from the back. As for the size of the holes, that depends on the size of the bolts you are using. I used 1/2" bolts, but 5/16" should work too.
Of note, this measurement is on the assembled torsion box.
@@DuraWoodworks Thank you! That information will save me a lot of trial and error.
Are you using 3 sheets of 3/4" and one sheet of 1/2"?
Wow. Crazy impressed with this design, tweaks, and overall video information.
Thank you for taking the time to do this. My 1 car garage is getting very short on space and this will help with space/tool management.
I just stumble upon your channel, I like what you do. Keep up the good work, looking forward to seeing more videos from you. I just bought an X-Carve myself, can't wait to put it to work.
Thank you very much! Best of luck with the new machine, it’s a blast putting it together and using it!
Hey I would just like to say thanks for the design idea. I know you got it from Tara’s design on the forum but your video helped a lot. I also downloaded plans and together mine came out great. I added the flip up side table for my laptop and I added a strap on front of the table to help raise and lower it. I also screwed in a block of would to keep the legs from moving. Anyway thanks again. I watched this video over 20 times. I also wanted to say thanks for the x carve build video. It really helped a lot.
Just bought an X Carve today. Love the idea of this folding table.
I've watched a few folding table solutions for the X Carve... this the best I've seen to date. Many attach the folding shelf directly to a wall... a problem on three counts... vibration transmitted through the building, It is fixed in only one location, no access around all four sides. This is great... will need to construct something 'very similar when my X Carve arrives.
An incredible project, great cutting and building tips. I've never used the wipe-on Poly before, such a finished look. Thanks for your time and detailed instructions. I am going to log into your link for a cut list.
I just ordered my X-carve, can't wait to get started.
Thanks a ton for the kind words Steve!
@@DuraWoodworks I got my X Carve and assembled it. I'm waiting for warmer weather to make your folding table in my workshop. Can't wait.
Steve Davis awesome! Take pictures when you make it. Would love to see how it turns out.
AWESOME thanks for share your project and knowledge, from Venezuela
Nice work. I really want to get my hands on an X-Carve.
Great table for the xcarve. I love the idea. I recently moved into a pretty decent sized shop. So I'm ok with a full sized table for my xcarve. But I like the idea and enjoyed the build. I really like the carve you did for the drawers and door. That looks great. I look forward to watching more videos. I just subscribed.
Thanks Angie! Hope you enjoy the videos!
I built one of these from Matthews plans a few months ago. Awesome design.
very nicely done. Looking forward to watching more of your videos!
Poor Man's DIY Thanks!
Thanks for the build ideas. There are beefier x carve table builds out there, but I think I will do something more like this since it seems to be the better bang for your buck. I like the custom drawer front idea... I'll probably take that note as well!
Cool use of space🌌
Excellent post!
PabloDeuce thanks!
Very nice work. I want to build one
I seriously enjoyed this video. Very calm and easy to follow instructions. Two questions for you. First, did you add knobs to you drawers? If not, how do you open? Second, did you ever get permission to build a set of prints for this project? Thanks in advance, and again, great video!
I am gonna steal that hot glue trick that was genius!
Thanks, but I can’t take all the credit haha. Think I got that idea from a David Picciuto (Make Something) video.
Just completed this build and your video and cut list was extremely helpful. I changed the width of the cabinet to 20" deep and the draw cabinet is 12" wide. You don't need legs with that depth. I just added a sliding bolt either side at the front to hold the table when horizontal. This works really well. One question, did you have to extend your cables for when the table is flipped vertical ? only mine don't seem to be long enough.
Has anyone had any issues over time storing an X Carve vertically. Most dont and since I have not bought one yet, I dont know how much strain that puts on any of the parts. I know the new version has a stiffer extruded rail and the router doesnt weigh too much but that's my concern with a vertical storage solution. LOOKS amazing and efficient. Great job!
What do you think about taking this basic idea and making it a complete flip top? I'm thinking some kind of brackets that fit over the X-axis - one on either side of the router - and attach to the threaded inserts in the wasteboard for support? That, and probably several more of the Inventables brackets/t-nuts at locations under the wasteboard to hold the frame to the top surface?
I was thinking of making this as a cart that could either hold the surface vertically for efficient storage, CNC side up for carving, or the other side up, and equip that with dog holes and t-track to use as an assembly and outfeed table.
The only change I might make to the front legs might have been a bolts with a rubber pad that screw in and out from the bottoms of the legs just in case the trolley is moved to an uneven section of the floor... very minor point though.
Nice build, my X-Carve arrives tomorrow, this will work great for it. What is the router setup you have on your Ridgid 4512?
It’s a Bosch RA1181 table. Fits nearly perfectly. Check my videos, I’ve got one explaining the install.
Nice way to save some space when not using it!
Good design. Well planned out. I would like to see some eye and ear protection. Also never wear gloves when using a table saw. The blade will drag your hand into the blade.
Keep up the good work. Stay safe.
Yeah, I learned that soon after this and it gave me nightmares thinking about doing it. It’s a learning process for sure! Thanks!
working on this now, any chance you remember the position in from the side for the leg bolts on the front of the torsion box? guessing like 1.5"? LOVE this design, thank you so much for the video!
Check the pinned thread, I believe I have those measurements in a reply there. Lemme know if those don’t work for you and I can go out and measure when I get back home.
@@DuraWoodworks thanks man! i was reading those as for the side of the frame to the box, but could be confusing it :)
@@adamsauls87 oh I hear ya. The ones on the front are 1.5” in from the left right on the front edge, and centered vertically if that makes sense.
@@DuraWoodworks makes perfect sense! Thanks again!
How do you like the Ridgid saw? And where did you get the router attachment?
I love it. For the money, you can't get much better of a saw. You've gotta do a little work to dial everything in right, but once you do it is great. As for the router table, if you check the description of this video ua-cam.com/video/cpIbrwtvAzY/v-deo.html you can find the link to it.
Could you share the hardware (nuts/bolts/hinge) list you used to assemble ?
Wipe on polyurethane finish... that's a new one on me... only ever seen/used brush on finishes... wonder if it is avalailable in the uk.
If not, you can make your own. There’s a link somewhere on UA-cam by one of the popular woodworking UA-cam folks.
What length of socket head screws did you use? 10mm?
Could you mount the controller box on the side of the cabinet so you can set your laptop on that ledge?
Yeah, that's definitely possible.
Josh, I finished my X-Carve table based on your incredible design. I made a few changes, 1. added drawer, 2. added side shelf for computer, 3. added lock mechanism to hold legs in place while storing or opening table. I took some pictures but haven't figured out how to attach them. Any thoughts?
Your best bet would probably be to add them on imgur or something similar and send the link along. Looking forward to seeing it!
Steve Davis that looks awesome! I like the darker stain. Thanks for the pictures!
@@DuraWoodworks Glad you got them, I took your advice and added the extra drawer and side shelf for my computer.
What a space saver when everything is folded up, Thanks for the video and cut list.
Any chance of throwing some dimensions for the plywood etc. cheers
My full time job is starting to die back down now, so I am having a lot more time for woodworking and projects. Should be able to get to this pretty soon. If you want something quicker, you can look up Tarqs design on the Inventables forum. It is heavily based on that and has mostly the same dimensions.
How far are the holes on the side supports to allow for rotation?
12 5/8"
Hey, great video. Do you still have the cut lists? Thanks
Sorry about that, had to reupload the file to a new host. If you check the link in the pinned comment it should be there now.
@@DuraWoodworks
Not yet…..
@@deejayk508 yeah give it a day or two. I had to update the DNS.
Did you ever complete the plans? I'd pay for them!
I have not. Between Tarq’s plans (linked in description) and my video, you should be able to get a good idea of how to do it though. You can open his plans in the free version of Fusion 360.
Have you uploaded design plans anywhere? Would love to make this.
Oops, just found the answer to that. Lol
@@mykeb804 Yeah, nothing yet. But hope to have something up soon.
Can you email the plans at shaunfridley@gmail.com please
shaun fridley Go search for Targ on the inventables forums and you will find them.
Where did you get 4 x 8 sheets of Baltic Birch all I can find is four by fives are five by fives
I bought these from Home Depot. They were the high grade sanded plywood. Still not the same quality as baltic birch, but pretty close.
Where could I find the measurements for the width and length of the base
18" x 60"
Is the insulation on your garage door a kit?
Nah, I just bought a couple 4x8 sheets from Lowe’s and cut them to size and fit them in.
@@DuraWoodworks Do you have plans for this build?
Scotty 2000SS not yet. Working on getting them uploaded.
Hey, is the cutlist still available? The link says it can't be found.
Just updated some settings on the site, it should be available at the same link again.
Any particular type of cloth best for wipe on polyurethane?
Any lint free cloth will do. But be sure not to leave them crumpled up in a pile! They give off heat and can combust.
Targ's email (and whole domain, actually) don't work anymore. Do you have some plans for this cart that you can share?
Unfortunately not, the only thing I have is the cut list I have linked in the description. I would rather not share Tarq’s plans without his approval and now I have no way to contact him.
Hey How do i get the plans?
Any plans available yet?
No plans yet, but the pinned comment has a cut list. This along with the video should give you a good idea.
Matthew Wilson it’s there now. It got unpinned somehow. Or I forgot to pin it when I first commented haha.
Any plans yet?
None yet. Between Tarq’s plans (linked in description) and my video, you should be able to get a good idea of how to do it though. You can open his plans in the free version of Fusion 360.
little advice.. when you make a video first show what you are going to make .. i had to skip to the end to see .. then when your finished show how it folds and stuff and how u use it !