FRM01 Cycle Timer Demonstration - All 18 functions
Вставка
- Опубліковано 3 жов 2024
- Showing what FRM01 cycle timer relay can do.
0:05 - Function 1
1:10 - Function 2
2:00 - Function 3
3:05 - Function 4
4:25 - Function 5
5:20 - Function 6
6:25 - Function 7
7:50 - Function 8
9:00 - Function 9
9:35 - Function 10
11:00 - Function 11
11:50 - Function 12
12:30 - Function 13
13:30 - Function 14
14:20 - Function 15
15:25 - Function 16
16:10 - Function 17
17:20 - Function 18
You can find the official manual here: goo.gl/5WU8Lf
Hope this helps you guys, if not, leave comment below. ;) - Навчання та стиль
4 years in, and this vid is still helping someone! My man!
This video helped me a lot to understand this product. The explanation by the manufacturer is terrible and his way of showing was sensational, congratulations and thanks for the help.
Great Video,,,Thanks for taking all that time to better educate us on all the functions. I for one ,,am useless at reading all the instructions, but watching your video makes life so much easier. Keep up the good work.
Great demonstration! This answers so many of my questions that would have been very difficult to get answered via email. Thank you!
A well Thought out video made the function of this timer simple so even I could understand it Thanks.
So much easier than trying to read and understand the instructions with the bad Chinese to English translation.
Hi, great video! A question how can i put 8 hours?
Well done. It was your video that convinced me to use this for my DIY swamp cooler project.
You are awesome, I only need one function of all, but it has it. Thanks.
Hi and thank you very much for your video! It helped me to understand all the features. Without it I would probably find it very hard ... or would not find it ... I THANK YOU
Even with the "corrected and rewritten" instructions the thought flow and English is somewhat broken. This helps to give a clearer picture of what each mode offers, thanks!
Excellent video. I am using this to program a door for my chicken house. I used two of them because I didn't want power on my actuator all the time and with two I can use it as a forward and reverse for the motor and still have the power time out and turn off.
Thank you very much for the great video clip.
Great! It has new version V2.0. Do you want to create new video about the new features?
Thank You so much as the instructions poor that and I could not get it to work but did what you did I was working in 5 mins later! Again thank you!
Glad to see this video, as was going to buy one and now understand it will not do what i want.
if any on can help, here is what i would like to get
a device that runs on 12v with 2x 12v output
and have a changeable/variable rate adjuster.
when a trigger is pressed that it then cycles a rate of on/off while the trigger is pressed and stops asap when not pressed
the rate i would like is about 900 to 1000 cycles of ON/OFF per min
Thank you so much!! This helped me great!! Now my fan on my car stays on a lil after each run I do at the drag strip!!! Thanks alot!!!
How does that help unless you also have an electric water pump? The heat is in the engine block and if it's going to boil over it's not because the water in the radiator is too hot.
@@DiffEQ I have a electric water pump also...
Very helpful. Using it for air tank condensate drain, 1 hour off, 3 seconds on, repeat.
Hello, can you show where the pulser is connected? Thank you
Yes thank you! Helped a lot =D
Great job. one important question for me is: de startbutton you use is it a puls push button or a contact button i.o.w when you press it does it keeps contact and if so wil it not harm the module when pressed for 2 seconds.
Can it be set to lower than 50 m/s ?
can a LDR (light dependent resistor) be used instead of the push button switch. what is the max. time it can be set. say I want to give power for 2 minutes then turn off
Very useful! Thank you a lot!
Great, thank you!
Hi Can you help please
Ive got a door with a micro switch contact, when the door opens i want a strobe to flash if the door is left open for more the 5 minutes. once the door closes i want the strobe to stop flashing.
Best Vid
This is awesome! I am trying to set this up to correct the order of my electrical components coming on for my stereo system in my car. The issue I'm having is when I go from key on to start I get a loud pop because the amp is on and doesn't have time to mute itself. When I go from key off all the way to start I have no pop because everything fires up in the correct order. Which function would I use to wire this as a delay, and also have it reset the delay timer with a power interruption when it goes from key on to start?
Which Function should I use to provide a set number of power cycles? Can
the timer be set to 0.1 or 0.01 seconds? I need to energize a fuel
injector for testing flow rate. What I'd need is to send power to the
Injector for example... 0.01 seconds ( on 0.01 and off 0.01) for 50
cycles, then stop the run automatically, so I can test several
Injectors and compare flow rates. Is that possible with this unit?
Como puedo modificar la velocidad de T1 y T2, no logro que caminen en segundos. Gracias
What kind of trigger switch you used in this video? Thankyou for responding😊
One Question. The connection you use on the movie, is it NO or NC
thank you very much
Hola. En la parte de alimentación del circuito con el botón como lo conectó
very good for developing tool...
where i bought tell me..
très bien fait, c'est top
on the #2 program what is the max time it can be set to stay on. and when the power is disconnected is the program permanently set until changed?
Ok so 1st button (set) press once and select program 1-18 with buttons 3 and 4.
Then 2nd button (swi) for MD. +/- buttons 3 &4 to select start time delay length.
Then 2nd button again (swi) for time run. +/- 3or4 select time run.
Then 2nd button again (swi) for run time pause. +/- 3or4 select time pause.
Then 2nd button again (swi) for # of cycles 1-99 or 00 for cycle unlimited.
Then press set to store?
And the next sequence you press set twice and store a different setup there?
So when you were done you had all 18 sets programed so you could just cycle through the set button and pick your program to run?
Does this thing have a reset to default ?
What is the default setup if there is one?
thank you very much
do any of the modes cause the timer to count 1,2,3...20 etc
Hello. Can I replace push-Button with a switch? Thanks for answer.
i have similar circuit but with voltage sense option. 12V DC 3 Digits Self-lock Relay PLC Cycle Timer Module Delay Time Switch D6W1
Can you help me to put it to use? i need voltage sense 15V relay switch, 13v relay swith back.
Does CH1 only operate with momentary contact, or can it recieve switched (+)? For my purposes, I need a relay that will be activated from a thermoswitch
Thanks for answering my previous question. Can i also use it with the connection NC in stead of NO. Will it work the other way around then, meaning will it normally keep the power on unless it is triggered and after the desired waiting time punt the power back on again. Will need it to stop my train on the exact point of the station and run again after waiting time.
thanks in advance.
Paul
@@cheapo7279 Thanks a lot. Now together with the Digitale display 30A DC 6 v ~ 60 v PWM Motor Speed Controller from Ali express I have a full automated line with programmable slow start, stop, installed stoptime and start again. Over and over again.All this with preprogrammed adjustable speed, slow start and stop. I could not have done it without your help. Thanks again.
Paul
i Need some thing Very Simular ,
i Need A Relay Switch When I Push the Button it comes On for 10 Sec. Every time you push it (Adjustable Timer) then Shuts Off !
I set #13 up the same as your card. I would like it to display seconds with a tenth (3.5 seconds). Changed NX many times and land up with the display much faster than a second or slower. Please does anyone have the correct setting to display a second with a tenth or hundred.
Hi, i want to make a fish feeder.. can this turn on a motor for 1 sec twice a day?
great job bro
I like to activate the relay every 24hrs. Can it be done and how?
I've watched this several times and am still stumped as to how to program a function that starts off, is triggered on once, then can not be triggered again for two minutes. The trigger is a signal from a motion sensor and the output is to a Halloween prop.
Hello.
T1 - 0.75 sec
T2 - 0.45 sec
Is this possible?
How can i set up this to turn on a circuit for 5 seconds when 12 volts is applied by car ignition switch then turn off till the next time the 12 volts is back on? We have a car computer that is not allowing us to complete a ground circuit to the starter relay. The ground is not at the lower side(coil) of the relay. We need circuit to helps us pass a ground signal to the starter relay for only 5 seconds then have to go off. would this work?
I'm still trying to figure out how to make it turn ON when triggered (5 sec.) by a motion detector, then stay ON for 30 sec., then Off. (NO REPEAT UNTIL MOTION IS DETECTED AGAIN.)
Function 8 is OK because it does Not turn Off the relay when sensing motion again until AFTER T1 time has expired.
BUT I MUST plug in a large number for T2 to keep relay Off until next motion is detected...
Maybe I'm missing something???
Does the timer start when the activation button is pressed or released? During mode ten you pressed and maybe held the button then released and it appeared to start when you released. Did I see that right? If I saw that right this thing is gonna be so good for my application
blowne85s10 Yes when button is depressed the countdown starts.
Just depends on whether you use a N.O. or N.C. switch. The actual trigger is a low to high transition, up to Vcc, but it does not have to be Vcc.
Please I need a setup like this with IR But when the IR detects something I need it to pulse vibrate like a cellphone ringing but every 2 seconds like a text message coming though
But when the IR detection is gone I need it to stop
I'm willing to pay for this by PayPal please let me know
How about 24 hours 7 days on and of?
I had a question regarding the sensitivity to magnetism - my relays are not keeping time correctly - deploying early (function 5 setting) but they are mounted very near a magnetic board. In your experience - would this be affecting the timer relay? Thanks
Mount the relay away from the magnetic board and see if the problem persists
Can it handle 110 Volts?
Can someone help me? I need a loop: 4h on, 20off, 4h on,...
I can find only english manuals and this is not good to understand for a german.
Select function 5, set the first time to 4hrs(on), set the second time to 20hrs(off), once powered on it with cycle these times indefinitely. If you needed it the opposite you could either select function 6 or just switch the NO/NC contacts. This would be 4hrs off, 20hrs on. You could also use the function where the high level CH1 would turn on the loop if you needed a trigger to set it off initially.
Hey i know this video is old but can this timer go into the milliseconds range? Ex: 11.2 secs? Greatly appreciate if you reply thanks man good work by the way!
Sir it is possible every three hours for 3 4 second sir please comment
Using any of the infinite cycle functions, yes.
How do you adjust the power save feature?
My display goes blank after a few seconds.
Thanks.
Thanks - just found a pretty good copy of the manual at www.easydiag.cz/fotky29604/fotov/_ps_202Timer-Relay-Module--FRM01--User-Manual.pdf
Long press [NUM+]. It will blink 3x when power save turns OFF
@@raygraham8972 Thanks a lot. Now I can understand it better
I need: after you press the button to: some time to turn in one direction, then some time in the other direction reverse. Then stop. Is that possible? Reverse provided? HEEELP !!!!!
Not directly.
Well done video, thanks for taking the time to go through all 18 functions. I have taken the Chinese translated instructions and have attempted to re-write them into English. This version of those instructions may help others as well (comments / corrections welcome):
drive.google.com/open?id=1jsU_TOydSPMvNCfahJBknnmSBocSFdI91JBhOhBy2hk
Good job. Some errors and omissions:
3. T1, displays T2 timing value (0-9999 seconds). .. should say T2.
You don't explain how to use NX to change from seconds to minutes to hours
You don't show how to use' long press NUM+ button' to enter power save mode (i.e. extinguish the LEDs)
demo yang sangat bagus, tetapi terlalu cepat untuk seorang yang sedang belajar...
👍🙂✅
Attiny 85 better 📣
wow nice..same technology i used in my incubator..my hatching results are awesome....watch my videos...
Y Gooooooooooooooood T Y