Відео

Great! It has new version V2.0. Do you want to create new video about the new features?

Hi, great video! A question how can i put 8 hours?

Como puedo modificar la velocidad de T1 y T2, no logro que caminen en segundos. Gracias

Hello, can you show where the pulser is connected? Thank you

Excellent video. I am using this to program a door for my chicken house. I used two of them because I didn't want power on my actuator all the time and with two I can use it as a forward and reverse for the motor and still have the power time out and turn off.

👍🙂✅

Yes thank you! Helped a lot =D

Best Vid

I've watched this several times and am still stumped as to how to program a function that starts off, is triggered on once, then can not be triggered again for two minutes. The trigger is a signal from a motion sensor and the output is to a Halloween prop.

Great, thank you!

This video helped me a lot to understand this product. The explanation by the manufacturer is terrible and his way of showing was sensational, congratulations and thanks for the help.

Can someone help me? I need a loop: 4h on, 20off, 4h on,... I can find only english manuals and this is not good to understand for a german.

Thank you very much for the great video clip.

4 years in, and this vid is still helping someone! My man!

Glad to see this video, as was going to buy one and now understand it will not do what i want. if any on can help, here is what i would like to get a device that runs on 12v with 2x 12v output and have a changeable/variable rate adjuster. when a trigger is pressed that it then cycles a rate of on/off while the trigger is pressed and stops asap when not pressed the rate i would like is about 900 to 1000 cycles of ON/OFF per min

Which Function should I use to provide a set number of power cycles? Can the timer be set to 0.1 or 0.01 seconds? I need to energize a fuel injector for testing flow rate. What I'd need is to send power to the Injector for example... 0.01 seconds ( on 0.01 and off 0.01) for 50 cycles, then stop the run automatically, so I can test several Injectors and compare flow rates. Is that possible with this unit?

Hola. En la parte de alimentación del circuito con el botón como lo conectó

Hi Can you help please Ive got a door with a micro switch contact, when the door opens i want a strobe to flash if the door is left open for more the 5 minutes. once the door closes i want the strobe to stop flashing.

Attiny 85 better 📣

very good for developing tool... where i bought tell me..

Very helpful. Using it for air tank condensate drain, 1 hour off, 3 seconds on, repeat.

You are awesome, I only need one function of all, but it has it. Thanks.

Thank You so much as the instructions poor that and I could not get it to work but did what you did I was working in 5 mins later! Again thank you!

Thanks for answering my previous question. Can i also use it with the connection NC in stead of NO. Will it work the other way around then, meaning will it normally keep the power on unless it is triggered and after the desired waiting time punt the power back on again. Will need it to stop my train on the exact point of the station and run again after waiting time. thanks in advance. Paul

Great job. one important question for me is: de startbutton you use is it a puls push button or a contact button i.o.w when you press it does it keeps contact and if so wil it not harm the module when pressed for 2 seconds.

What kind of trigger switch you used in this video? Thankyou for responding😊

How about 24 hours 7 days on and of?

One Question. The connection you use on the movie, is it NO or NC

Sir it is possible every three hours for 3 4 second sir please comment

do any of the modes cause the timer to count 1,2,3...20 etc

Even with the "corrected and rewritten" instructions the thought flow and English is somewhat broken. This helps to give a clearer picture of what each mode offers, thanks!

Well done video, thanks for taking the time to go through all 18 functions. I have taken the Chinese translated instructions and have attempted to re-write them into English. This version of those instructions may help others as well (comments / corrections welcome): drive.google.com/open?id=1jsU_TOydSPMvNCfahJBknnmSBocSFdI91JBhOhBy2hk

Thank you so much!! This helped me great!! Now my fan on my car stays on a lil after each run I do at the drag strip!!! Thanks alot!!!

thank you very much

demo yang sangat bagus, tetapi terlalu cepat untuk seorang yang sedang belajar...

wow nice..same technology i used in my incubator..my hatching results are awesome....watch my videos...

Does CH1 only operate with momentary contact, or can it recieve switched (+)? For my purposes, I need a relay that will be activated from a thermoswitch

Can it be set to lower than 50 m/s ?

Y Gooooooooooooooood T Y

A well Thought out video made the function of this timer simple so even I could understand it Thanks. So much easier than trying to read and understand the instructions with the bad Chinese to English translation.

मूझै लैना हे 9829731148

Hi and thank you very much for your video! It helped me to understand all the features. Without it I would probably find it very hard ... or would not find it ... I THANK YOU

Hey i know this video is old but can this timer go into the milliseconds range? Ex: 11.2 secs? Greatly appreciate if you reply thanks man good work by the way!

Great Video,,,Thanks for taking all that time to better educate us on all the functions. I for one ,,am useless at reading all the instructions, but watching your video makes life so much easier. Keep up the good work.

great job bro

Can it handle 110 Volts?

I'm still trying to figure out how to make it turn ON when triggered (5 sec.) by a motion detector, then stay ON for 30 sec., then Off. (NO REPEAT UNTIL MOTION IS DETECTED AGAIN.) Function 8 is OK because it does Not turn Off the relay when sensing motion again until AFTER T1 time has expired. BUT I MUST plug in a large number for T2 to keep relay Off until next motion is detected... Maybe I'm missing something???

i Need some thing Very Simular , i Need A Relay Switch When I Push the Button it comes On for 10 Sec. Every time you push it (Adjustable Timer) then Shuts Off !

Hi, i want to make a fish feeder.. can this turn on a motor for 1 sec twice a day?

Hello. T1 - 0.75 sec T2 - 0.45 sec Is this possible?