Carbtune Pro Ural Motorcycle accurately synchronized

Поділитися
Вставка
  • Опубліковано 22 гру 2024

КОМЕНТАРІ • 37

  • @Yipcanjo
    @Yipcanjo Рік тому +2

    Thanks for putting this video on UA-cam! I'm hoping to do this myself in a few days 👍

    • @CreakyRider
      @CreakyRider  Рік тому

      No worries , hope it goes well 👍

  • @alexikoerner8527
    @alexikoerner8527 2 роки тому +2

    a tool more than necessary, I have the same as you; very effective and accurate

  • @haitch1980
    @haitch1980 2 роки тому +4

    Hi there Keith. Coincidence would have it, that I too purchased a new calibration kit as I couldn't source one the same as yours. So, bought an electronic one. No rods, just a bar graph and damping system. Plugged it in to Ruby for a quick test and balance was bang on. As you would expect from new. If you are looking at OBD2 for yourself, I got lots of help from Lee for DIY. You only need the right plugs, a device which transmits Bluetooth or wifi, and an App for your phone. Still waiting on the last plug to come from a place which shall remain nameless. Then will try it out. So far it's under $100.

    • @CreakyRider
      @CreakyRider  2 роки тому +2

      Good stuff , let us know how it goes.
      I’ve been looking at some ideas. 👍

    • @anitakeers
      @anitakeers 2 роки тому

      @@CreakyRider I am interested too in a OBD solution that is not so ridiculous expensive as the original sold by Ural..... The software can be downloaded for free.

  • @ferrydewit3416
    @ferrydewit3416 4 місяці тому +1

    You can check the temperature of the cilinders with a laser temperature gun (don’t know how they are called in English). You have to make sure though that you can set it on measuring metal. When you are done with your cilinders you can use it in the kitchen. 🙂

  • @Fudders
    @Fudders 11 місяців тому +2

    Thanks for the video, that looks like an effective and pretty straightforward way to balance the throttle bodies (or carbs) on a bike.
    BTW, do you realise the right cylinder is a couple of inches further back then the left cylinder on a Ural and BMW boxer engine?!
    So unless you have a size 14 left foot and a size 8 right foot, I'm not sure the warming of your feet is a very accurate method to check the balance of the throttle bodies or carbs!
    The smoothness of the engine at idle and at revs (which was noticeable in your video) seems a much better yardstick of how well balanced the TBs are! 😉

  • @Uraljunkie
    @Uraljunkie 2 роки тому +1

    Really nice - well done. I wish my 2018 had vacuum ports on the throttle bodies!

    • @CreakyRider
      @CreakyRider  2 роки тому

      That’s a bummer, how can you balance the throttles ?

    • @Uraljunkie
      @Uraljunkie 2 роки тому +1

      @@CreakyRider I haven’t. Seems to be running fine though. I will need to drill and tap some ports in the throttle bodies to sync. I have adjusted the idle though…

    • @CreakyRider
      @CreakyRider  2 роки тому +1

      @@Uraljunkie that’s a bummer , there must be some other of way of balancing the throttles if you don’t have access?

    • @Uraljunkie
      @Uraljunkie 2 роки тому +1

      @@CreakyRider Maybe you can do it through the OBD port, but not sure - not to mention I don’t have the Ural diag program.
      Maybe a good project for when it warms up. I searched for a tool, but they appear to all use vacuum ports (lots of adapters like yours has).

    • @CreakyRider
      @CreakyRider  2 роки тому

      @@Uraljunkie yeah , cool , a little research project.
      I’m in the process of getting an OBD setup , just ordered some plugs and cables etc , we will see if I can get it to work.

  • @iliasmetalworks
    @iliasmetalworks 2 роки тому +2

    Should you adjust the vacuum at idle or at part throttle also?
    I am asking because valve clearances variations apply on the vacuum also. So if I have adjusted the same vacuum at idle that means that I shouldn't apply any throttle and call it a day? Or same vacuum at idle doesn't mean that I will have same vacuum readings at part throttle?

    • @CreakyRider
      @CreakyRider  2 роки тому +1

      The instructions say to check it at Part throttle on so you get a smooth and accurate reading.
      It bounces around too much at idle.

    • @iliasmetalworks
      @iliasmetalworks 2 роки тому +2

      @@CreakyRider Thanks for your reply!

  • @anitakeers
    @anitakeers 2 роки тому +2

    I'm gonna get me one too to use it for all my bikes. All 4 are 2 cylinder bikes :)

    • @CreakyRider
      @CreakyRider  2 роки тому

      This is my first twin cylinder bike , so it’s new to me 👍

  • @MollysPa
    @MollysPa 7 місяців тому +1

    Save yourself $400. Spend $25 on 16' of 3/16" (0.187") ID clear plastic tubing and some red transmission fluid (Marvel Mystery oil works too). Zip-tie a 2.5' loop to a yard stick and inject 20ml of red fluid into the loop. Warm the engine to operating temperature. You'll have two 5.5' lengths of plastic tubing to take vacuum from the 3/16" ports on each throttle body; they're the ones with the small plastic caps. If necessary, balance and set the TB's at idle with no throttle applied using the 3/32" hexhead screws & 5/15" locking nuts on each TB, matching the fluid levels on each side of the loop as you adjust to the desired idle speed. I set the idle just high enough to extinguish the alternator light. Then balance the TBs at the cable adjusters holding the throttle off-idle to around 1000 to 1200 RPM. This procedure applies to Urals 2019 and newer.

  • @deney54
    @deney54 2 роки тому +1

    Hi Creaky.... So what do you think about if we will be able to get parts for our Urals... Some parts places here in the U.S. think they will be able to get parts from other countries... or filter parts out of Ukraine or Russia to other countries so we can get parts, what do you think are parts we should get now ? I sent for Oil filters and should get them next week.

    • @CreakyRider
      @CreakyRider  2 роки тому

      There are alternative oil filters , Ryco make a compatible one , there are people making gaskets etc.
      I don’t see general maintenance as a problem.
      A major rebuild or something might be a problem in the future , we don’t know , let’s hope for peace , not just for our bikes but for the people.

  • @razem1
    @razem1 2 роки тому +1

    Hi
    Is it balancing just about adjustment of throttle cables? Is that the way to tune/ballance carbs?
    Thanks

    • @CreakyRider
      @CreakyRider  2 роки тому +1

      Yeah , pretty much , the cables need to pull the throttle on each carbie equally.
      The carbtune let’s you balance them
      accurately .

  • @annafraley5388
    @annafraley5388 2 роки тому +1

    Do you have to cut or trim anything.??
    I have read where the stainless steel rods have to be cut certain lengths depending on the type of motorcycle. Did this have to be setup FOR the Ural.?.

    • @CreakyRider
      @CreakyRider  2 роки тому +1

      No it's all ready to go. It comes with a piece of clear tubing to use for restriction (damping) you just cut a couple of pieces with scissors and add them to the tubing , very easy , and it all work perfectly. It has very good instructions and also more stuff on their website.

    • @annafraley5388
      @annafraley5388 2 роки тому +1

      @@CreakyRider .. thanks, we have two other devices but that seems way easier... IF you have nipple ports taped into the throttle bodies.

    • @coleacanth8944
      @coleacanth8944 10 місяців тому

      it measures vacuum as a fixed unit, you adjust the bike not the gauge

  • @jtp480
    @jtp480 6 місяців тому +1

    Nice bike.

  • @ratdog7050
    @ratdog7050 Рік тому +1

    What year is your Ural? My new to me 2023 has Electronic Idle Control. So go are the days of sync the idle then at higher RPM, now it is just higher RPM.

    • @CreakyRider
      @CreakyRider  Рік тому

      Yeah mine is a 2020 model , I think it’s just to make sure the cables are pulling evenly on the throttles. Mine was a little bit out , I need to check it again next time I do a big service.

  • @joaquinbermudez5807
    @joaquinbermudez5807 Рік тому +1

    Do restrictors come with it ?

    • @CreakyRider
      @CreakyRider  Рік тому

      yeah , it has all the bits you need.

  • @richardstephens9647
    @richardstephens9647 2 роки тому +1

    are your heads above water????? Stay safe