2009 Ford F 150 Repair - Part 3 - Installing the New Rack and Pinion
Вставка
- Опубліковано 5 вер 2024
- This video is for educational purposes only but is pretty much a step by step of all the tasks we did to install the Rack and Pinion.
1. Bungee the steering wheel down so it can't spin.
2. Take the tires off
3. Remove the hydraulic hoses to the rack and pinion
4. Disconnect the tie rods
5. Disconnect the Intermediate Steering Shaft
6. Remove the bolts for the Rack and Pinion
7. remove rack and pinion
Check and make sure that your tie rods are in good shape as well as the Intermediate Steering Shaft.
We bought the rack and pinion from Napa Auto Parts along with the steering fluid.
Tools used were:
Milwaukee M18 FUEL 18V Lithium-Ion Brushless Cordless 1/2-inch Impact Wrench with Friction Ring (Tool Only) model 2767-20
Milwaukee XC 5Ah battery
Milwaukee M18 Fuel 18V Surge 1/4 inch Hex Hydraulic Driver (Tool Only)
Milwaukee M12 and M18 12V/18V Lithium-Ion MultiVage Rapid Battery Charger
8" extension bar (1/2" drive)
10mm socket (3/8" drive)
3" and 6" extension bar (3/8" drive)
13mm impact socket (1/2" drive)
19mm impact socket (1/2" drive)
2 adjustable wrenches
Seafoam Deep Creep penetrating spray
flat screw driver
18oz Estwing hammer
8lbs sledge hammer
Thank you once again to all our new Subscribers!!!
Until the next one, keep Living the Northern Life!
You can help support the channel if you Subscribe and hit the Bell notification for All updates so that you are notified when I post a new video.
You can also help support the channel by clicking on the links to any of the items below.
Even if you choose not to purchase any of these items we would receive a commission if you purchase any item from Amazon within 24 hours of clicking on any link below.
9 inch Chainsaw Tooth Brush Blade
Canada: amzn.to/2CQJPm7
USA: amzn.to/2ECFlQB
Sharpening Stones
DMT WM8CX-WB 8-Inch Duo Sharp Plus Bench Stone - Coarse/Extra Coarse with Base
Canada - amzn.to/2Yogfey
USA - amzn.to/2QxPII5
DMT WM8EF-WB 8-Inch DuoSharp Plus Bench Stone - Extra Fine/Fine With Base
Canada - amzn.to/2UwsSTu
USA - amzn.to/3lljtKx
Microphone
Neewer CM14 Mic Phone Mic on-Camera Video Microphone with Shock Mount
Canada: amzn.to/37RKTRF
USA: amzn.to/3b1CcpG
I normally do all my recording with my iPhone but my tripod doesn't have a way to mount a cold shoe so I found the Ulanzi ST-02S and it just mounts to my current tripod
Ulanzi ST-02S Newest Aluminum Phone Tripod Mount w Cold Shoe Mount
Canada: amzn.to/37VZqvJ
USA: amzn.to/3b1QI0G
JOBY GorillaPod 3K Kit. Compact Tripod 3K Stand and Ballhead 3K for Compact Mirrorless Cameras or Devices up to 3K (6.6lbs). Black/Charcoal
Canada - amzn.to/2zr7zvu
USA - amzn.to/2YI1ILQ
AmazonBasics Chest Mount Harness for GoPro Camera - Black
Canada - amzn.to/2UyHyBU
USA - amzn.to/2ExwrEc
Amazon Prime
Canada: www.amazon.ca/...
USA: www.amazon.com...
Books
Learn to Timber Frame
Canada: amzn.to/2I0Jyhi
USA: amzn.to/2EFSKaz
Build a Classic Timber-Framed House: Planning & Design/Traditional Materials/Affordable Methods
Canada: amzn.to/2Gn15hI
USA: amzn.to/2kbBrEv
Timber Framing for the Rest of Us: A Guide to Contemporary Post and Beam Construction
Canada: amzn.to/3a4orUY
USA: amzn.to/32xNw99
Tools
Swanson Tool SO107 12-Inch Speed Square
Canada: amzn.to/2wzgAkz
USA: amzn.to/2G0MB9v
Big Horn Marking Knife
Canada: amzn.to/2UhoSIF
USA: amzn.to/2YJElkP
STANLEY FatMax Premium Tape, 35-Feet x 1-1/4-Inch
Canada: amzn.to/34zH4yR
USA: amzn.to/2Qzx9U4
Ryoba 9-1/2" Double Edge Razor Saw
Canada: amzn.to/2WNc6OC
USA: amzn.to/31DhZUa
Milwaukee 48-59-1808 M18 & M12 Rapid Charger
Canada: amzn.to/2HekiCq
USA: amzn.to/2Exx6FG
Fiskars 18" Billhook Saw
Canada: amzn.to/2XyRaim
USA: amzn.to/2QxOblo
Fiskars Axe And Knife Sharpener
Canada: amzn.to/3cjdu3z
USA: amzn.to/32vKDpi
Wood is Good 30oz Mallet
Canada: amzn.to/2WVz5dy
USA: amzn.to/2G76GLx
Lee Valley:
Veritas Mk.II Standard Honing Guide - www.leevalley....
Veritas Honing Compound - www.leevalley....
Barr 2" Framing Chisel - barrtools.com/...
Search Terms:
Barr Tools
Barr Chisels
Chisel
DIY
Homestead
Timber frame
Timber Framing
Timber Framing Chisels
Woodworking
Woodworking Chisels
Woodworking Tools
#231
Thanks for this video. Its the only one i could find with this generation of Ford using a hydraulic steering system.👏👍
Thanks!
Father: "how many you at?"
son: "oh i dont know, i lost count a while ago"
classic
hahahaha
it only really matters that the air is totally out of the lines so not terrible. :)
Good video guys!
Thank you!
Wow, those rotors are rustier than most anchor chains on a 1945 liberty ship.
Hahahahaha
Absolutely!!!
It is a rust bucket for sure!
😂😂😂
Did you have really hard steering before you replaced it
We're not professionals but we had a line that popped and was leaking fluid everywhere.
The power steering wouldn't work at all and it felt almost impossible to turn the wheels.
There is a steering shaft in there that can cause it to feel similar as the knuckels seize up but it gets hard to steer and then releases and feels jerky to steer.
Or you could be low on fluid.
Not sure that helps.
Andrew
Necesita todo nuevo
We didn’t have anything used available so we bought a new one.
How long does it take to do a job like that?
That will depend on how rusty the system is.
The short steering shaft can get very rusty and might need replacing like ours did.
Getting into an area to loosen the bolts can be an adventure as there is very little room unless you have a hoist.
I think it took as a few hours to do but we split it up into two days.
Removing was the hard part.
Best of luck!
Andrew
Did you guys flash program it ?
This is not the electronic steering so there was no need to flash it for the rack and pinion.
R U gonna change those rotors look in bad shape
Hey Adam,
Yes we will be doing it this summer.
We will also be doing the callipers and some body work as well now that we have the engine bulletproofed as well.
Thanks for watching and commenting!
Dude your rotors are trashed
Yes they sure are.
This truck is a project and isn't currently on the road. My son has been learning lots on it.
Great project that's for sure.
You should have pressure washed that decrepit ride before starting this nasty job. But then again maybe you were afraid that blowing of 200# of rust off would compromise the structural integrity. I will never go back to the salt belt again.
We're going to take the good parts off of it now and sell the rest for scrap metal... not much else we can do.
We should have been under spraying it all these years.
Jesus Christ. I think it's time to junk that thing. Rusted to hell. Knock in the engine sounds like a phaser or multiple lifters. Frame has deep rust penetration.
Oh and you over torqued the outer tie rods. Your gonna mess up the boot and make it go out faster. Best of luck on this thing. Mine is a 09 5.4 and it looks amazing must be a lot of salt where y'all live.
Yes sir!
It was the phasers and we have replaced them after this.
Truck is still running but agree it has seen better days.
Thanks for watching and commenting.
nah, its great father son teamwork on an old truck, this is something they will look back on with joy.