Amigão, excelente dica. Salvou meu dia. Muito obrigado. Eu estava quase desistindo mas um dos comentários me animou a insistir. Os caras queriam trocar módulo, botão e até motor.
Hi, I am looking for a similar device. With little difference. It should start a buzzer once water level in the tank comes below a certain level. The changes needed would be as follows: 1> Instead of 1 water tank the system should work with 8 separate tanks 2> For all the tanks, the buzzer should go off when the water level reaches dead level - say 15% 3> Each LED corresponding to that tank should start and buzzer for that should go off 4> After the buzzer goes of there should be manual button which can be used to turn it off/reset Can you design something like this? I guess it might need more buzzers, ine for each tank.
Thank you for this awesome experiment.. now i'm think for more functionality, Ex: Buzzer beep on 100% and 25% level, with only one buzzer.. imagine if High and Low level we got alert, that was greatly feature.
Did you get it to work? I'm using only one buzzer on 25% and 100%. The problem now I have is the buzzer beeps all the time. So I don't know which one cause the buzzer to beep 25% or 100%.
This is a bit different, but for anyone looking for a simple, free off/on switch for water level, try pulling a water level switch from an old washing machine. I used one for controlling a pump on some homebrewing equipment. It works using air pressure. There is usually a 3-level adjustment knob. Just attach the vinyl tubing on the switch to a piece of cpvc. Et voila!
Excellent but just one point someone mentioned Oil tanks in the comments below.... i am familiar with fuel level indicaters and they also use resistance however its an floats height relative to an coil that carries an measurable variable resistance as the floats height changes an resistance is measured this is what is displayed with the level indicator however normally these are double insulated or even totally isolated from the fluid environment...I think the commentator may need to consider this as even the slightest spark or arc could result in fire potential...fuel is highly flammable water is not but regardless this is excellent work thats done here and thanks for sharing i say to the uploader...
For those that wonder about waters conductivity. Most tap water is a fair conductor. Ask anyone that got a shock while standing on a wet floor or soil in their bare feet. The dissolved solids in the water make it more conductive. Distilled water is the least conductive.
@@kamleshpatil-g5t Tale my word for it. DC will shock you and kill you. Not necessarily in that order. I believe the charge coming from an AED heart starter is DC.
One thing I learned from a similar circuit is to use float switches because after a while it’s going to build up resistance and give false positives from the minerals in the water This is a pretty cool circuit though
@@kamleshpatil-g5t actually DC is slightly more dangerous but 3.7 volt isn’t enough to shock you EVs are around 400v and you wouldn’t want to use that high of a voltage around water unprojected that’s why they still have a 12 volt battery and equipment in the electric cars
I've been using a similar circuit since the 1980s to turn the water pump on and off for the house water tank. The water pump automatically turns on when the tank is 30 percent empty and turns off automatically when the tank is full.2-pair telephone wire was used for 12 volt DC current from the tank to the circuit. Now I will try to build this circuit with some modifications. I've been using a similar circuit since the 1980s to turn the water pump on and off for the house water tank. The water pump automatically turns on when the tank is 30 percent empty and turns off automatically when the tank is full. 2 micro switches on tank and nylon cord inside the tank have been used. There is no loss of current. Now I will try to build this circuit with some modifications. گھر کے پانی کے ٹینک کے واٹر پمپ کو آن اور آف کر نے کے لیے میں اس سے ملتا جلتا سرکٹ ۱۹۸۰ سے استمعال کر رہا ہوں۔ ۳۰ پرسنٹ ٹینک خالی ہونے پر واٹر پمپ خودبخود آن ہوتا ہے اور ٹینک فل ہونے پر خود ہی بند ہو جاتا ہے اس میں ٹینک سے سرکٹ تک ۱۲ وولٹ ڈی سی کرنٹ کے لیے ۲ پیئر والا ٹیلیفون وائراستمعال کیا ہے۔ ٹینک کے او پر2 مائیکرو سوئج اور ٹینک کےاندرنائیلون کی ڈور کا استمعال کیا ہے۔ اس سے کرنٹ کا کوئی خظرہ نہیں۔ اب کچھ تبد یلیوں کے ساتھ یہ سرکٹ بنا کراستمعال کروں گا۔
It works. Anyhow, the whole thing will not last long because it keep transmitting data. continuously. And it will also interfering other nearby device and violate the transmission regulations.
Nice idea but you will jam up the frequency so car remotes and just about anything that works on 433mhz will now not work. You need to add a small timer to switch on the transmitter on for 2 or 3 seconds every 10minutes to be legal and not jam up the frequency. Also transmitting continuously will flatten the battery in the TX in a day or 2.
Yes just put the alarm resistor on the 25% led and use float switches I’d use float switches with water also because in higher humidity you’ll get false positives especially when it’s in use for a long period of time
Can i use a piece of wire as a antenna i put this tx and rx circuit in different containers plastic one in water tank with peice or wire out of it does it work???
possible with using a pnp transistor. but you also need to stop pump when the tank is full. so you will use a start/stop circuit. you can do it with limit swithches simply or an electronic circuit.
This is intermittent level monitoring like ultrasonic detectors installed for certain level's, or level switches for certain levels. For continuous level monitoring, an ultrasonic detector is installed on the top of a tank, as the level increases, the ultrasonic waves cut results in the change of digital display.
the electrode inside the tank will wear out in a very short amount of time due to electrolysis or simply by corrossion. Think of some non contact process.
@@anmol9803Flot Switch Will Not Gives Three Channel Signal For Water level Signal. For This CCT Only Solution is STAIN LESS STEEL Sensors Can be Used for Long Periods in Water.
nice video. I have 5 diesel generators of 400kva , with 3000 liter diesel tank each. So i need i need fuel level and digital data, but i have no idea what to do. Will you suggest any circuit or any instrument so i can wach fuel data in my office.
Good and affordable circuit, but one disadvantage, the transmitter circuit will be full time on and the battery will drain, if we put a switch than the same lengthy wires from tank to the house is to run where receiver circuit is fitted. Send the solution
@@gjaltdijkstra8264 yeah but there is a better workaround for that and that is nrf wireless modules, if we use these modules we can make it a working wireless water tank monitor in real life, otherwise ur project is for kids only ig.
you can use use buzzer last connection instead of red light. buzzer can create lots of noise. instead of this you can automate the pump connection. so that tank automatically fill when it is going to be empty.
You can make NOT gate using transistor so that lowest level of water touching the sensor keeps the buzzer off while open circuit (meaning empty container) gives out signal to the buzzer.
It's with in a one feet distance therefore it's alarm 🚨 signal incase 3-floor tank and ground floor sump it's given a signals with good way perfectly.....
Hello, Range in open space (Standard Conditions) 500 Meters with Antenna / 100-200 Meters without Antenna....For component prices visit robocomp.in Link is given in the Discription Thank you so much
Try this on ac to dc adapter but don't dip the wire into the water while using adapter. Just connect COM to any of 4 channels. I used 9v battery with 7805 and it didn't work. I thought I had bad soldered connections. It was because of battery.
Amigão, excelente dica. Salvou meu dia. Muito obrigado. Eu estava quase desistindo mas um dos comentários me animou a insistir. Os caras queriam trocar módulo, botão e até motor.
So nice the world's best teacher
Thank you so much.....
Hi, I am looking for a similar device. With little difference. It should start a buzzer once water level in the tank comes below a certain level.
The changes needed would be as follows:
1> Instead of 1 water tank the system should work with 8 separate tanks
2> For all the tanks, the buzzer should go off when the water level reaches dead level - say 15%
3> Each LED corresponding to that tank should start and buzzer for that should go off
4> After the buzzer goes of there should be manual button which can be used to turn it off/reset
Can you design something like this? I guess it might need more buzzers, ine for each tank.
Thank you for this awesome experiment..
now i'm think for more functionality,
Ex: Buzzer beep on 100% and 25% level, with only one buzzer..
imagine if High and Low level we got alert, that was greatly feature.
Did you get it to work? I'm using only one buzzer on 25% and 100%.
The problem now I have is the buzzer beeps all the time. So I don't know which one cause the buzzer to beep 25% or 100%.
You can make 2 circuits with diffrent sound buzzers😂
This is a bit different, but for anyone looking for a simple, free off/on switch for water level, try pulling a water level switch from an old washing machine. I used one for controlling a pump on some homebrewing equipment. It works using air pressure. There is usually a 3-level adjustment knob. Just attach the vinyl tubing on the switch to a piece of cpvc. Et voila!
Excellent but just one point someone mentioned Oil tanks in the comments below.... i am familiar with fuel level indicaters and they also use resistance however its an floats height relative to an coil that carries an measurable variable resistance as the floats height changes an resistance is measured this is what is displayed with the level indicator however normally these are double insulated or even totally isolated from the fluid environment...I think the commentator may need to consider this as even the slightest spark or arc could result in fire potential...fuel is highly flammable water is not but regardless this is excellent work thats done here and thanks for sharing i say to the uploader...
Nice work! Next version to give a low-level alarm intermittently, say few beeps every 1 minute.
Muy buen proyecto. Te quedo invertido los cables el buffer debe pitar cuando queda vacío, solo es de invertir los cables
Well and Nice circuit
Please update it with auto switch off motor...
For those that wonder about waters conductivity. Most tap water is a fair conductor.
Ask anyone that got a shock while standing on a wet floor or soil in their bare feet. The dissolved solids in the water make it more conductive. Distilled water is the least conductive.
That is true. But, you should be aware that electricity used in this project is DC. I guess DC voltage doesn't give you shock...
@@kamleshpatil-g5t Tale my word for it. DC will shock you and kill you. Not necessarily in that order. I believe the charge coming from an AED heart starter is DC.
@@kamleshpatil-g5t DC can injure or kill you as well as AC, the major factor is the voltage.
One thing I learned from a similar circuit is to use float switches because after a while it’s going to build up resistance and give false positives from the minerals in the water
This is a pretty cool circuit though
@@kamleshpatil-g5t actually DC is slightly more dangerous but 3.7 volt isn’t enough to shock you
EVs are around 400v and you wouldn’t want to use that high of a voltage around water unprojected that’s why they still have a 12 volt battery and equipment in the electric cars
Wonderfully done. Such a useful idea for many. Thank you for sharing and a great video.
Good project, please link for buy 434MHz Tx & Rx RF Module? Datasheet or name components? Thank you
nice point to point soldering. I would've reversed the colors of the leds so red shows when it's nearing capacity or use bar graph led
I would have used a clean soldering iron.
15:00 - The alarm should sound only when the water level reaches the lowest point in a water tank.
Yes it's possible
What is the maximum distance between transmitter and receiver?
I've been using a similar circuit since the 1980s to turn the water pump on and off for the house water tank. The water pump automatically turns on when the tank is 30 percent empty and turns off automatically when the tank is full.2-pair telephone wire was used for 12 volt DC current from the tank to the circuit. Now I will try to build this circuit with some modifications.
I've been using a similar circuit since the 1980s to turn the water pump on and off for the house water tank. The water pump automatically turns on when the tank is 30 percent empty and turns off automatically when the tank is full. 2 micro switches on tank and nylon cord inside the tank have been used. There is no loss of current. Now I will try to build this circuit with some modifications.
گھر کے پانی کے ٹینک کے واٹر پمپ کو آن اور آف کر نے کے لیے میں اس سے ملتا جلتا سرکٹ ۱۹۸۰ سے استمعال کر رہا ہوں۔ ۳۰ پرسنٹ ٹینک خالی ہونے پر واٹر پمپ خودبخود آن ہوتا ہے اور ٹینک فل ہونے پر خود ہی بند ہو جاتا ہے اس میں ٹینک سے سرکٹ تک ۱۲ وولٹ ڈی سی کرنٹ کے لیے ۲ پیئر والا ٹیلیفون وائراستمعال کیا ہے۔ ٹینک کے او پر2 مائیکرو سوئج اور ٹینک کےاندرنائیلون کی ڈور کا استمعال کیا ہے۔ اس سے کرنٹ کا کوئی خظرہ نہیں۔ اب کچھ تبد یلیوں کے ساتھ یہ سرکٹ بنا کراستمعال کروں گا۔
It's about 5-6 meeters
5, 6 m is poor range
I made this one and its range is 30meters
@@ishtiakME
20 to 30 meters inside the building,or 70 to 100 meters open air
It works. Anyhow, the whole thing will not last long because it keep transmitting data. continuously. And it will also interfering other nearby device and violate the transmission regulations.
Nice idea but you will jam up the frequency so car remotes and just about anything that works on 433mhz will now not work. You need to add a small timer to switch on the transmitter on for 2 or 3 seconds every 10minutes to be legal and not jam up the frequency. Also transmitting continuously will flatten the battery in the TX in a day or 2.
another work of art not just a piece of electronics!
It's garbage and a waste of time
@@gregl7597 i never build any so if it work or not is not my point i consider it a work of art visually.
@@ponetwozerodrone3707 you're still wasting your time.
Use your knowledge to build PRACTICAL things.
Melhor vídeo do dia do UA-cam
Ganhou um inscrito do
BRASIL
Faz um video montado uma mesa com sensores de pra ascende led agora
Very nice project good 👍 keep it up
Thank you so much sir
ट्रांसमीटर और रिसीवर के मैक्सिमम डिस्टेंस को भी कितना रखा जा सकता है ⁉️ बताना आवश्यक होता है जो यहाँ नहीं बताया ❓
100 meters
Good.
E Polytechnic. A technical channel.
Thanks...
Nice one! Can this be used for Home Heating Oil Tank levels with the alarm going off when the tank is down to 1/4 full?
Yes just put the alarm resistor on the 25% led and use float switches
I’d use float switches with water also because in higher humidity you’ll get false positives especially when it’s in use for a long period of time
This is the best circuit I have ever seen...!!
Awesome videos hn sb, kindly spot welding k lye koi project bnain jo easy ho or acha ho jo 12Volt se chale
Sure sir, Thanks for watching 😊
Exellent bro....!🔥🔥🔥
Thank you very much 😊
Thanks for the useful project
You are welcome
Excellent video.
Thank you very much!
Which resistor is the one soldered righ after the leads , no specs in the video or diagram
Hello, There is a piece of blue color pvc wire insulator which use for insulation in cross connection. Thanks for Watching my videos 😊
At 10:00 in your video you are soldering one blue color component across all the LEDs ..what is it? Please mention it..
There are wire crossings, so a piece of wire has been installed for insulation. Thanks for Watching.
I noticed that as well and knew what was that
I can use another transmitter/receiver? Thanks
Yes, of course
Can i use a piece of wire as a antenna i put this tx and rx circuit in different containers plastic one in water tank with peice or wire out of it does it work???
Very educative & simple process BUT will you guide me from where I can get Complete fully automatic system
This bulb like a guaranteed never explode or ruined, if like this make for room type like nightlight, the size?
Thanks! Perfect idea..
Thanks and most welcome
Thanks my friend, is it possible to add a relay for the pump and it works when the level reaches 25%
possible with using a pnp transistor. but you also need to stop pump when the tank is full. so you will use a start/stop circuit. you can do it with limit swithches simply or an electronic circuit.
This is intermittent level monitoring like ultrasonic detectors installed for certain level's, or level switches for certain levels.
For continuous level monitoring, an ultrasonic detector is installed on the top of a tank, as the level increases, the ultrasonic waves cut results in the change of digital display.
What is the component you are soldering at 9:53 minute? That component does not appear in the diagrams or component list. Is it necessary?
not component its a Gnd pin insulate
Eline emeğine sağlık TEŞEKÜRLER.
Most Welcome bro.... And thanks for watching my videos 😊
Thank you 👏👏👏👏👏👏
the electrode inside the tank will wear out in a very short amount of time due to electrolysis or simply by corrossion. Think of some non contact process.
Then, you've to use float switch.
@@anmol9803 float switch will not give you real time data on the height of water.
@@apurbadas5810 it will if you thi k a little bit about how to do it rather than being negative about it.
USE SS Material For Sensors
@@anmol9803Flot Switch Will Not Gives Three Channel Signal For Water level Signal.
For This CCT Only Solution is STAIN LESS STEEL Sensors Can be Used for Long Periods in Water.
उन लोगों के लिए जो पानी की चालकता के बारे में आश्चर्य करते हैं, उनसे पूछिए जिन्हें पानी पर पैर रखने के बाद बिजली का झटका लगा
It hcjfjf
Exhalent 👌👍👏
Very nice and information technology
Thanks
nice video.
I have 5 diesel generators of 400kva , with 3000 liter diesel tank each. So i need i need fuel level and digital data, but i have no idea what to do. Will you suggest any circuit or any instrument so i can wach fuel data in my office.
Nice sir. Could it be used safely for gasoline?
yes ! dont worry
It may or may not work as it requires the liquid to be at least slightly electro-conductive. Not sure gasoline is. But it is safe enough to try.
Can it be used in a metal tank?
Yes
Good and affordable circuit, but one disadvantage, the transmitter circuit will be full time on and the battery will drain, if we put a switch than the same lengthy wires from tank to the house is to run where receiver circuit is fitted. Send the solution
Nice one...very helpful demonstration..
Thank you so much....
good indea but can we add more leds to show more accurate level?
Yes but that means also more wires in the tank. And more wiring.
@@gjaltdijkstra8264 yeah but there is a better workaround for that and that is nrf wireless modules, if we use these modules we can make it a working wireless water tank monitor in real life, otherwise ur project is for kids only ig.
@@joshitoshi9835 what is the name of your channel, illustrate us
Very good Technology.
What is its coverage range between transmitter and receiver, plz explain
500 meter
@@azamkhan-km2fjare you sure?
Hello Bro, Range in open space (Standard Conditions) 500 Meters (with Antenna) / 100-200 Meters (without Antenna). Thank you for watching
Sir please add automatic on,off motor circuit
will this work same in 1100ltr water tank too ? Or any volt difference required
I doubt it will work on real water tank. Probably work only on bucket of water.
Anyway, this is good for learning electronic.
Вместо зуммера можно поставить блок контроля выключения насоса подачи воды. Чтобы не было перелива. И будет замечательно
Very good project sir
Thank you so much
Nice project 👍
Thanks 😊
Important ye he underground se overhead ka distance tak work hona chahiye
How do you make it buzz when it's empty and not filled instead. I could use one of these for my greenhouse
you can use use buzzer last connection instead of red light.
buzzer can create lots of noise. instead of this you can automate the pump connection. so that tank automatically fill when it is going to be empty.
You can make NOT gate using transistor so that lowest level of water touching the sensor keeps the buzzer off while open circuit (meaning empty container) gives out signal to the buzzer.
Just invert the water sensor wire sequence.
Good Project and Good Job.
But I have a question. How many meter distance it will work?
It's with in a one feet distance therefore it's alarm 🚨 signal incase 3-floor tank and ground floor sump it's given a signals with good way perfectly.....
Does the wire corrode with electrolysis or the wire stays protected?
Good project🎉
Thank you
You are brilliant. But who will make all these.
Background Music is good
Thanks
Woah, that's really cool!
Muy bueno, pero me serviría si sonara el buzzer cuando quede 25% de liquido. Muchas Gracias
I have made this video on your request so please watch it soon... Link ua-cam.com/video/idMgV8YTucw/v-deo.html
How to total price?
How many Maximum distance between transmeter and reciver?
Readymade circuit multi he.?
What is the range of it
10 किलोमीटर
Thanks for your replying
Can we get it from Mkt
Ji, how to determine resistor type for led. Say I have 5volt led them what resistor to be selected
Hello!
Do you have any experience of how such a simple cable sensor behaves in the water in the long term? Scale or dirty water in the evening.
Very interesting ICs....
This is great! Would you show us how to make a wireless spanking machine? (The wife wanted me to ask).
Can we tramsmit audio over the transmiter and recive via reciever ❓️
Amazing Thanks !! So Simple if you know how to do ..:-)
You're welcome!
Aap ne jo zener diode led ke positive leg pelagaya uska value kya hai
What equipment a required in design a system
If there are two or three systems nearby, will there be any interference.
How long this battery on tank module will survive
Which technology is used this product?
Could this concept be converted to turn wireless turn signals.
This is really great work! God blessed your hands 🙌 man!
Is that work for liquid chemical tankers? Please let me know.
Thanks 🙏
No it will not. You use plastic floats for chemical.
Good my question Sir, give the number of what you put on the + point of the led,
good project bro and helpful for us what is range of transmitter and receiver and what is cost of this project.
Hello, Range in open space (Standard Conditions) 500 Meters with Antenna / 100-200 Meters without Antenna....For component prices visit robocomp.in Link is given in the Discription Thank you so much
@@anuragprojects thanks bro for your valuable reply
@@anuragprojects on that page they only have 433 MHz
Nice project!!
Thanks!
Very good. Hope you have tried it from a distance of 50 M
For how many distance it's work? and for how many days battery works?
Can we make a transmitter camera and a sender at the door of the house 👍👍
The Buzzer is driving by full Position ?
Can it meetr ? Signal
How long will the transmitter battery last if it is turned on 24/7?
Hello Anurag, the google doc does not open. Can you please take a look?
How many time live the batery? hello, from argentina.
is it possible to switch on and off motor
by altering this circuit
When i connect continuse deep sound blows, singnal light not glows, please sugest solution, i tryed 2 times also
Try this on ac to dc adapter but don't dip the wire into the water while using adapter. Just connect COM to any of 4 channels.
I used 9v battery with 7805 and it didn't work. I thought I had bad soldered connections. It was because of battery.
@@jumbo999614 tq sir
Great, pleases please link for buy 434MHz Tx & Rx RF Module?
is there one that can send an sms to my phone? would be great for my boat.
What is the problem?
When i connect supply, all the level LED are glowing.
Line sgnal is not on.
Continuous beep coming.
Same problem for me, do you find any solution sir