I'm researching using peltier devices for cooling a water reservoir of about 16 gallons. I doubt I'll use water as a heat sink but, who knows? It's still a great idea. Just wanted you to know that I appreciated the video and the parts list. You've given me inspiration and you've motivated me to try something similar.
tks my hat is off to you Sir great work was working on a similar project with four modules! now I've seen you showing the project made me feel great with similar idea tks again
@@kalaiselvan3956 at least he tried and built it smarten us up.... your contribution to his effort should have been a plain "thanks for the idea buddy" and not a comment about excrement...
Nice video, IMO this is better than the heatsink fan version with all the fan noise. Need to check if the water cooling for the hot side is sufficient though, otherwise it wont last. Thanks for sharing practical sample u had done. I will try this myself with some adjustment. Cheers.
Yes Thank you very much If the hot face is well radiated, the cold side will be very cold The highest temperature of hot water I measured reached 45 degrees Thank you very much Wish you a happy day my friend
Forget about these, I spent some time researching and finally I found out the pipes in most of these are made of copper. U don't want your tank water to be running through copper or aluminium if u want your water creatures to survive, I dropped this as a solution
Thanks for the video. Perfect! Have you tried to use the blue radiator with, instead of a water-pump ... an air-pump to get cold air ? I am curious to see if I can get the cold air from the Peltier module using a radiator with air-pump to build a small fridge. Do you think it might works ? Thanks!
Идея хороша, но для аквариума нужно переделывать. Ведь аквариумная вода содержит бактерии и дейтрит. Со временем водоблок забьется и обростет бактериями. Упадёт эффективность. Холодный контур должен быть изолирован от аквариума. Рекомендую использовать бронзовую трубку как радиатор в аквариуме.
Yes Thank you very much for sharing your thoughts with me and everyone In this clip I just want to test the performance of this product for everyone to know To use the fact we will have to do better Thank you very much Wish you a happy day my friend Please share with me your good ideas
Бронзу нельза как и латунь. Они содержат медь, а это яд для аквариума и тем более если это креветочник. Так еще они могут содержать свинец, нужно искать пищевую. Нержавека пищевая может быть. Но опять же для человека может и не смертельно, а вот для маленького замкнутого водного объема это вопрос.
You shouldn't mix raw aluminum with aquatic life. Similiar effect can be achieve by applying thermoelectric cold side to side of sump filter tanks except thermo exchange will be much slower.
Отлично! Как вариант можно для холодной части использовать фильтр, а контроллер использовать для элементов Пельтье и помпы на горячей части. Great! As an option is possible for cold part to use the filter, and the controller to use for elements, Pelt`e and pump on hot part.
i think if you connect the cold water pipe to the canister near to the aquarium inbound. Then for the hot water add a aluminium radiator or even a water cooling radiator just one like PC liquid cooling and then connect this pipe to external water source as you did may increase efficiency a lot.
It works but not efficient and things become clumsy and it partially reduces appeal of the fish tank. More over this can be used in either a single medium tank or two small tanks. I used ups to power these thermo electric coolers incase Power cuts happen. Hiding everything in a separate box is the key to make it look better. Go for it only if you really need this like shrimps and sensitive fishes.
That's an amazing & interesting project. Simply brilliant. I am staying in Bangladesh where I don't think I can get all the tools required here. Can you please help whether those would be available in Amazon or eBay from where I could bring them?
My friend These are just tests requested by everyone I have not tried using it for a long time But the water will be better, but the water will evaporate and the radiator fan will be different
dude.... you applying thermal paste like nutella. thick layer of thermal paste make effect of isolating instead of transfering heat.. also your thermal paste is not effective, try using liquid metal or something bettter will improve efficiency
Hello, sir. How it is possible that we all know a peltier has also a warm side yet you attached also same bar on the warm side but stll can produce decent amount of temperature? Does the wirings do the trick? Ty
Hi there, thank you for you effort, what a nice video. Its inspiring for those who wants to use DIY feature on their project. 👍 So the idea on your video is to pump the cool water from your tank through the warm side of the peltier into the water bin, and pump the warm water from the bin into the tank? Is this correct? Can I use DIY external filter (without filter media) for the water bin? I have built a chiller using dc fan, peltier and heatsink, but its so noisy, I can't stand it. And also its not effective since in 12 hrs the temp only drop 4°C from 30° to 26°. I am planning to follow your video. But I still can't understand how it works. If its not to much trouble, could you please explain it for me? Thanks a lot. 🤝
I think it can't burn the sensor It only makes the Chip Chip inadequate I apologize for the late reply Because last time I was in the hospital hAVE a nice day My friend
the second water look, you need to cool that water too. This will not scale well if you are not removing that heat. Would have been better using regular cpu fans for the TECs hot faces or using a radiator with fans in the heat face water loop. You would have gotten better quite better results. Excelent work.
Ok.....so many quesions. Why a waterblock on the cold AND hot side of the peltiers??? Is that why the extra water tank is needed??? Why not a heatsink and a couple if pc fans. Would that not eliminate the need for that water buffer? Maling it all more easy to use?? The controller looks interesting
Thanks for sharing this videos. It's very interesting. In your video Aquarium model 7 you've used air refrigeration for the hot side of chip-peltier. why you don't used in this case. Is less efficienty than flow water?
Hello Piece Of Paper, Such a great idea. Idea from Piece of paper to practical reality 😎 Please let me know- 1) Does this setup can work 24/7 at desired cooling effect without issues? 2) Did you try setting much lower temperature like 5 degree C? 3) Is the hot side portion enough to disipate the heat? Or do I need to attach heatsink and fan, if I want to run it for 24/7? 4) Is 5 litres water enough for cooling the hot side? Thank you
@@suryadipdas984 , I also did it later on. Used 5 peltier cooling modules with 2 heat syncs and a fan for each. A can of water with submersible pump. Also got 33amps power supply. An exaust fan to blow cold air in front. Then dismantled the unit and used it in a thick wall thermocol box and turned it into a fridge. Total waste. These videos are just for fooling viewers to get views.
I wonder where you find the water cooling for the Thermoelectric. With two of TEC1-12730 you can make a chiller almost 0.5 kW the problem is the 12v DC too much Amp
I wonder if the inlet of the heat cooling block can use the water from the water supplied by the chilled water. Meaning, pump water runs in to the inlet of the heat block, outlet of the in block runs to the inlet of the cooling block, then the outlet of the cooling block runs to the tank.
I am sorry but I do not understand what you are trying to say to me I apologize for my poor English skills Please speak more clearly Thank you very much Wish you a happy day my friend
Can you please prolong the yellow read information ormany diagram longer . Few secound is too short . Please make it at least 10...15 sec. Great job. Thanks
Is the water on the other tank not going to boil up? Cuz what I know is, peltier are produce cold on one side and heat on the other side. If its getting to hot, the other side will less to produce cold. Does the other tank do that job?
Nyc work bro.. ur channel name in d video is sometimes hiding d information in video 5:51 temperature is not visible. And temperature in that white colour monitor is dull use any lights 9:51..
@@ramesh10829 the dtmax of the peltier 12706 is 60-70 degrees. So the difference between the cold and hot side needs to be managed to an extent that the target cold water temp is reached. Hence when the relay is cut off, the radiator tank get a chance to naturally cool down a bit. Yet I think it can safely increase till 50 degree c. Basically it seems that it works great for this use case. I want to employ this technique for outdoor hydroponics by using water in an earthen pot as a radiator. Have a hunch that it will work.
I'm also not sure about that I just wanted to do an experiment and share that test with everyone They cannot replace specialized products but can also be replaced when we cannot afford genuine products. Have a nice day My FRIEND
Mình có làm như bạn nhưng ko hạ được nhiệt vì bên tản nhiệt nước bị quá nóng không thể làm lạnh được như bạn. Không hiểu lý do tại sao. Bên bể chứa nước tản nhiệt dung tích bao nhiêu lít vậy bạn? Học cách phát âm
Bạn chỉ nên làm cái này cho hồ nhỏ thôi Hồ to như của mình không được đâu dùng lâu lắm Như trong Clip mình cũng đo bên thùng nước nóng lúc nhiệt độ cao nhất là 45 độ mình phải thay nước trong cái bể nóng vì mặt nóng càng được làm mát thì mặt lạnh càng lạnh Nhưng mình thấy nếu nghịch mà hồ nhỏ thì làm cái thùng xốp bỏ đá + nước như clip sau mình làm ấy lạnh nhanh mà đỡ tốn kém hơn nhiều
Hello! Amazing video and work. I have a 200 liter fish tank. I can use the same elements or I have to boost up them? If yes, what do you suggest me? Thank you so much
You cant use Alu or Copper in a fish tank... The alu will find something to oxidize like steel impellers, and then cause corrosion which will end up killing everything in your tank. Brass is fine if you have no snails / shrimps as it can potentially leech copper. If you can find a titanum or stainless steel waterblock, it will work, otherwise your asking to kill all your fish. Do research on what is considered SAFE metals in a fish tank before you recommend people doing it.
i have smilar idea but without cut off module ( i dont know whats the name of the module ) , i want to make one tank with temp as lower as possible, thank you , your video helping me :D
Cảm ơn bạn nhé Mình cũng không chắc lắm Cái này mình chỉ làm thí nghiệm cho mọi người thôi Nhưng máy lạnh cũng như sưởi Nên dùng thừa công suất một chút thì đỡ tốn điện chứ dùng thiếu công suất thì tốn điện lắm mà cũng không hiệu quả
I am sorry but I tried to cool down my 50ltr tank with 3 peltier 12706 but the temperature is not decreasing after 27degree centigrade... Help me with some information
hello there, I have been follow ur video and did everything same as you but I have been end up the temperature only drop for 0.4C(28 C room temp) for almost 1 hour and the hot water goes up to 40C, I wonder whats the problem actually
Nó là cảm biến đóng cắt nhiệt độ, nó có đóng cắt theo cả nóng và lạnh tùy mình cài đặt, cái mình dùng test thì rẻ thôi trước mình dùng cho lồng ấp gà bạn lên shopee sẽ có còn nếu dùng cho những thiết bị khác và dùng lâu dài thì nên mua cái tốt hơn
Hi.....I'm using 3 tec 12715 modules with 12v 20A power supply......the heating part found to be having too much heat even after using car coolant with water and a small radiator setup for cooling the coolant.....is that ok to run for more than an hour....???
hello friend, excuse me if i got you wrong but i think you have the same missunderstand that i had he uses 2 blue radiator because one side cools the water and the other side warms the water peltier works as one side of it getting cold and the other hot Ive seen many projects where they use an fan or heat dissipator on the hot side but it seems that also using water in the hot side works better thats why he has 2 tanks of water. 1 gets cold and the other gets hot hope i could make it clear
Yes I just want to do a test on the types of radiators I found it better to use water radiators We can do more neatly during use You must have a temperature controller like mine The temperature controller controls the machine when the temperature exceeds the required level
I understand how the system works. I'm just saying that if a radiotor with its both sides have peltiers to cool water and the hot sides of peltier have heatsinks. Then you need only one pump to regulate the water. I have a diagram. Add me as a friend to send it to you!
Great vedeo.Can you share the specs of power supply module.Also if the ciculation tank is placed 2 ft below the fish tank,than would you require a more powerful pump in it?
I'm researching using peltier devices for cooling a water reservoir of about 16 gallons. I doubt I'll use water as a heat sink but, who knows? It's still a great idea. Just wanted you to know that I appreciated the video and the parts list. You've given me inspiration and you've motivated me to try something similar.
It was great DIY I saw . its work perfectly and I will use that in my planted tank . thank you for your best learning
tks my hat is off to you Sir great work was working on a similar project with four modules! now I've seen you showing the project made me feel great with similar idea tks again
Thank you very much
Have a nice day My Friend
GREAT TUTO .... clear and practice
Thank you very much
Have a nice day My Friend
Very good, thanks. I will use is for cooling the water of my 4 Tower hydroponic setup.
So much knowledge that you give me about fish tank and accessories sir.. thank you so much!
Thank you very much
Have a nice day My Friend
Hey man, you could make millions in the hydroponic industry!! Just remember who told you that!👌🏼
Great work
Thank you very much
Have a nice day My Friend
Thanks a lot man.. you saved my money, what are all idea i have in my mind you tried out and gave the results. 🤩
I dont have words, just amazing my friend. Thanks for the idea
Thank you very much
Have a nice day My Friend
Where can i buy this tool...?
Water cooling for hot side is really good idea, better than fans, just space consuming consuming.
Awesome video 🤙
Based on your test I Made cooling system based on platier
For my 220 liter tank
So did it worked?
This method using direct water flow is more efficient and works faster. Good idea
Thank you very much
Have a nice day My Friend
@@pieceofpaper924 it's a piece of shit ...Peltier never works .!!
Piece of Paper como chama esse aparelho, qual a capacidade dele pq queria fazer um nano reef isso seria bom
@@kalaiselvan3956 u need more study
@@kalaiselvan3956 at least he tried and built it smarten us up.... your contribution to his effort should have been a plain "thanks for the idea buddy" and not a comment about excrement...
Крутая идея 👍
Nice video, IMO this is better than the heatsink fan version with all the fan noise. Need to check if the water cooling for the hot side is sufficient though, otherwise it wont last. Thanks for sharing practical sample u had done. I will try this myself with some adjustment. Cheers.
Yes
Thank you very much
If the hot face is well radiated, the cold side will be very cold
The highest temperature of hot water I measured reached 45 degrees
Thank you very much
Wish you a happy day my friend
Forget about these, I spent some time researching and finally I found out the pipes in most of these are made of copper. U don't want your tank water to be running through copper or aluminium if u want your water creatures to survive, I dropped this as a solution
Yes my friend. It was just a little experiment. It was a request from a friend who wanted me to make a video to prove it. It really didn't work.
Thanks for the video. Perfect!
Have you tried to use the blue radiator with, instead of a water-pump ... an air-pump to get cold air ? I am curious to see if I can get the cold air from the Peltier module using a radiator with air-pump to build a small fridge. Do you think it might works ? Thanks!
This is just great !!
My frend your film is very good & your work is carful tank you.
Thank you very much
Have a nice day My Friend
Super video
Thank you very much
Have a nice day My Friend
super dupper ...🔥🔥
simply awesome!
Thank you very much
Have a nice day My Friend
Идея хороша, но для аквариума нужно переделывать. Ведь аквариумная вода содержит бактерии и дейтрит. Со временем водоблок забьется и обростет бактериями. Упадёт эффективность. Холодный контур должен быть изолирован от аквариума. Рекомендую использовать бронзовую трубку как радиатор в аквариуме.
Yes
Thank you very much for sharing your thoughts with me and everyone
In this clip I just want to test the performance of this product for everyone to know
To use the fact we will have to do better
Thank you very much
Wish you a happy day my friend
Please share with me your good ideas
Бронзу нельза как и латунь. Они содержат медь, а это яд для аквариума и тем более если это креветочник. Так еще они могут содержать свинец, нужно искать пищевую. Нержавека пищевая может быть. Но опять же для человека может и не смертельно, а вот для маленького замкнутого водного объема это вопрос.
You shouldn't mix raw aluminum with aquatic life. Similiar effect can be achieve by applying thermoelectric cold side to side of sump filter tanks except thermo exchange will be much slower.
Did not understand the wire management from 4:10 to 4:37 how did you connect the cables with power supply.
Please advice sir... i have the same question ?? And please tell me the spesification power supply ..
He drew the diagram wrong obviously. The thermostat comes in between the power supply and the electricity
If it cools the water too quickly it can stress the fish and even kill them! So it work really good on the big tank of 180 litres!
How many degrees did you win
Отлично! Как вариант можно для холодной части использовать фильтр, а контроллер использовать для элементов Пельтье и помпы на горячей части.
Great! As an option is possible for cold part to use the filter, and the controller to use for elements, Pelt`e and pump on hot part.
I apologize for my late reply because I have been in the hospital for the past few days
Thank you very much
Have a nice day
i think if you connect the cold water pipe to the canister near to the aquarium inbound. Then for the hot water add a aluminium radiator or even a water cooling radiator just one like PC liquid cooling and then connect this pipe to external water source as you did may increase efficiency a lot.
Do you know if it releases aluminium in the water ?
Yes my friend. It was just a little experiment. It was a request from a friend who wanted me to make a video to prove it. It really didn't work.
nice, thanks for the idea mate)
It works but not efficient and things become clumsy and it partially reduces appeal of the fish tank. More over this can be used in either a single medium tank or two small tanks. I used ups to power these thermo electric coolers incase Power cuts happen.
Hiding everything in a separate box is the key to make it look better. Go for it only if you really need this like shrimps and sensitive fishes.
Is aluminum from cooling blocks toxic to fish?
That's an amazing & interesting project. Simply brilliant. I am staying in Bangladesh where I don't think I can get all the tools required here. Can you please help whether those would be available in Amazon or eBay from where I could bring them?
its working, thanks
Thank you very much
Have a nice day My Friend
so u use one more water block and pump for reduce heat too. does it better than fan
My friend
These are just tests requested by everyone
I have not tried using it for a long time
But the water will be better, but the water will evaporate and the radiator fan will be different
Спасибо за идеи.
I apologize for the late reply
Thank you very much
have a nice day My Friend
Have to agree, a bit heavy on the thermal paste. Interesting idea for a heat sink, a container of water. Might be able to make some cups of tea :-)
Thank you very much
I will try to do better
Have a nice day My Friend
GOOD VIDEO 👍
Thank you very much
Have a nice day My Friend
a great idea and very kreatif..itu long white box what ... provide the name of any material that is in vidio ... I want to try at home ...👌👌👌
Thank you very much
Have a nice day My Friend
dude.... you applying thermal paste like nutella. thick layer of thermal paste make effect of isolating instead of transfering heat.. also your thermal paste is not effective, try using liquid metal or something bettter will improve efficiency
Yes
Thank you very much for sharing your thoughts with me
I will do better in the next test
Thank you very much
Wish you a happy day my friend
Can anyone mention any liquid metal paste brand? Pls
@@royan.jdm2 thermal grizly or cool labotry
Hello, sir. How it is possible that we all know a peltier has also a warm side yet you attached also same bar on the warm side but stll can produce decent amount of temperature? Does the wirings do the trick? Ty
it could also be possible to reverse polarisation so you can heat your tank .......
^^
Maybe I will make a video about your idea in the winter
Now in my country it is summer
Wish you a happy day my friend
Hi there, thank you for you effort, what a nice video. Its inspiring for those who wants to use DIY feature on their project. 👍
So the idea on your video is to pump the cool water from your tank through the warm side of the peltier into the water bin, and pump the warm water from the bin into the tank? Is this correct? Can I use DIY external filter (without filter media) for the water bin? I have built a chiller using dc fan, peltier and heatsink, but its so noisy, I can't stand it. And also its not effective since in 12 hrs the temp only drop 4°C from 30° to 26°. I am planning to follow your video. But I still can't understand how it works. If its not to much trouble, could you please explain it for me? Thanks a lot. 🤝
Did you solve it? It work? I’m trying to do the same thing
El aluminio de los bloques de refrigeración es toxico para los peces?
Can i use 12v 10A power supply for this project
This alluminium water block safe for fish
Nice! Just check out how to apply thermal grease.
XH-W1209 Temp. Sensor Controller max only 20A , 4-peltier is 24A, will it burn the relay sensor?
I think it can't burn the sensor
It only makes the Chip Chip inadequate
I apologize for the late reply
Because last time I was in the hospital
hAVE a nice day My friend
Nice
Can I run this 24/7 ? Does it consume lot of power
Actually, I just did a test for everyone about its effectiveness
If you actually use it, you should use professional equipment like that to save a lot
What's name of black paste you apply to water block
the second water look, you need to cool that water too. This will not scale well if you are not removing that heat. Would have been better using regular cpu fans for the TECs hot faces or using a radiator with fans in the heat face water loop. You would have gotten better quite better results.
Excelent work.
Thank you very much
I just want to do experiments to share with people about them
Have a nice day, my friend
but a good silent fan is expensive, why don't you make couple of stages basin with a very thin layer of water. theoritacally it will cool much faster
Water cooling is better than just a cooling fan.. Like a car radiator.
hello sir
5000 L how much use Thermoelectric cooler TEC1-12706
plz reply
Ok.....so many quesions.
Why a waterblock on the cold AND hot side of the peltiers??? Is that why the extra water tank is needed???
Why not a heatsink and a couple if pc fans.
Would that not eliminate the need for that water buffer? Maling it all more easy to use??
The controller looks interesting
Hello, I want to ask, which one will be more effective when using 1 100w chip versus using 2 50w chips?
Thanks for sharing this videos. It's very interesting. In your video Aquarium model 7 you've used air refrigeration for the hot side of chip-peltier. why you don't used in this case. Is less efficienty than flow water?
Thank you very much
I just want to do the experiment and share my test with everyone
Have a nice day, my friend
One water block will work? one peltier how litters water will cool?
Hello Piece Of Paper, Such a great idea. Idea from Piece of paper to practical reality 😎
Please let me know-
1) Does this setup can work 24/7 at desired cooling effect without issues?
2) Did you try setting much lower temperature like 5 degree C?
3) Is the hot side portion enough to disipate the heat? Or do I need to attach heatsink and fan, if I want to run it for 24/7?
4) Is 5 litres water enough for cooling the hot side?
Thank you
Hello Ketansa, I also have similar setup.. if you use 5ltr water for the hot side, after some time the water will boil.. that I can assure you 🤣
@@suryadipdas984 , I also did it later on. Used 5 peltier cooling modules with 2 heat syncs and a fan for each. A can of water with submersible pump. Also got 33amps power supply. An exaust fan to blow cold air in front.
Then dismantled the unit and used it in a thick wall thermocol box and turned it into a fridge.
Total waste.
These videos are just for fooling viewers to get views.
I wonder where you find the water cooling for the Thermoelectric. With two of TEC1-12730 you can make a chiller almost 0.5 kW the problem is the 12v DC too much Amp
It's a perfect substitute for chillers if you have a 10 gallon tank or 5 gallon tank. Using a chiller on such a small tank is overkill.
Is that titanium make? Can we use it for saltwater aquarium?
Did you find how to make salt water aquarium work?
@@diegochinchilla3209 no not yet.
Shyam sundar after several
Days trying to solve this problem, I came up with the idea of making my own cooler
Shyam sundar I’m gonna make it out of thin layer of glass. Doing it like that, is gonna make me let use the same design of the video
@@diegochinchilla3209 ua-cam.com/video/N9p0Pm1Okh4/v-deo.html
This link may help you.
But we can't find the titanium coil which he used.
I wonder if the inlet of the heat cooling block can use the water from the water supplied by the chilled water.
Meaning, pump water runs in to the inlet of the heat block, outlet of the in block runs to the inlet of the cooling block, then the outlet of the cooling block runs to the tank.
I am sorry but I do not understand what you are trying to say to me
I apologize for my poor English skills
Please speak more clearly
Thank you very much
Wish you a happy day my friend
That would mean the heat taken would back to the water cooled with the peltier.
Thanks
Thank you very much
Have a nice day My Friend
mantap sungguh ribet mau nyari dingin 😂😂😂. di tempat ku suhu 24 derajat cukup pake kipas fan aja
great video! like following the channel
But for this we need to have another tank with water .. is there any idea without using extra tank with water .. ?
Can you please prolong the yellow read information ormany diagram longer . Few secound is too short . Please make it at least 10...15 sec.
Great job. Thanks
Is the water on the other tank not going to boil up? Cuz what I know is, peltier are produce cold on one side and heat on the other side. If its getting to hot, the other side will less to produce cold. Does the other tank do that job?
Nyc work bro.. ur channel name in d video is sometimes hiding d information in video 5:51 temperature is not visible. And temperature in that white colour monitor is dull use any lights 9:51..
Where did u order the peltier from?
isn't one side of the peltier hot and the other side cold? you got one plate to the cold side and another plate to the hot side?
Thank's Bro.
Awesome
I apologize for my late reply because I have been in the hospital for the past few days
THANK You very much
Have a nice day
how much capacity power supply used dude?
hi do u think I can replace the heating dissipating side with a fan coil rather than water tubing instead?
Can i use jerry can as reservoir for the cooling water (hot side) or it has to be open reservoir?
I only know if the hotter side of CHIPTEC is cooler, the cooler side of CHIPTEC will be colder
Thank you very much
Have a nice day My Friend
The other tray contains heated water, so is it not bad for the peltier if it's not cooled. Heated water will be circulating in the other heat sink
Thank you very much
Have a nice day @Ramesh Balakrishnan
I apologize for my late reply because I have been in the hospital for the past few days
@@pieceofpaper924 you have not answered my question
I'm sorry but I don't understand what you want to ask me
I apologize because my English is not good
You can speak more clearly
Thank you very much
The peltier gets could but needs heat to work
@@ramesh10829 the dtmax of the peltier 12706 is 60-70 degrees. So the difference between the cold and hot side needs to be managed to an extent that the target cold water temp is reached. Hence when the relay is cut off, the radiator tank get a chance to naturally cool down a bit. Yet I think it can safely increase till 50 degree c. Basically it seems that it works great for this use case. I want to employ this technique for outdoor hydroponics by using water in an earthen pot as a radiator. Have a hunch that it will work.
Hello my Brother, I hope all is well with you!
Can you tell me if this project serves to heat the water in the aquarium as well?
You use power supply 12v5a ?
That’s a wonderful project bro! Where did you buy all the components for this project? Thanks
Awesome device. Can that be made on a bigger scale or?
I'm also not sure about that
I just wanted to do an experiment and share that test with everyone
They cannot replace specialized products but can also be replaced when we cannot afford genuine products.
Have a nice day My FRIEND
Piece of Paper awesome job either way chief. Was thinking about doing this for a nano tank I setup for the wifey. Lol
^^ My Friend
Can we connect the pump also to the thermostat so that it will auto cutoff it?
this 100liter or below60 liter?
Mình có làm như bạn nhưng ko hạ được nhiệt vì bên tản nhiệt nước bị quá nóng không thể làm lạnh được như bạn. Không hiểu lý do tại sao. Bên bể chứa nước tản nhiệt dung tích bao nhiêu lít vậy bạn?
Học cách phát âm
Bạn chỉ nên làm cái này cho hồ nhỏ thôi
Hồ to như của mình không được đâu dùng lâu lắm
Như trong Clip mình cũng đo bên thùng nước nóng lúc nhiệt độ cao nhất là 45 độ mình phải thay nước trong cái bể nóng vì mặt nóng càng được làm mát thì mặt lạnh càng lạnh
Nhưng mình thấy nếu nghịch mà hồ nhỏ thì làm cái thùng xốp bỏ đá + nước như clip sau mình làm ấy lạnh nhanh mà đỡ tốn kém hơn nhiều
How big of a converter would I need for 5 peltier 5amps?
Hi..
Do you use heatsink ?
Thank you
Hello! Amazing video and work. I have a 200 liter fish tank. I can use the same elements or I have to boost up them? If yes, what do you suggest me? Thank you so much
Im curious too
Chờ clip làm chiller cho hồ trên 80L mà mãi chưa thấy a ơi, mong có clip chỉ đường
You cant use Alu or Copper in a fish tank... The alu will find something to oxidize like steel impellers, and then cause corrosion which will end up killing everything in your tank.
Brass is fine if you have no snails / shrimps as it can potentially leech copper.
If you can find a titanum or stainless steel waterblock, it will work, otherwise your asking to kill all your fish.
Do research on what is considered SAFE metals in a fish tank before you recommend people doing it.
Did you were able to get a titanium cooling block ??
i have smilar idea but without cut off module ( i dont know whats the name of the module ) , i want to make one tank with temp as lower as possible, thank you , your video helping me :D
Bạn ơi bể 60 40 40 thì nên dùng mấy con sò 60w hả bạn
Cảm ơn bạn nhé
Mình cũng không chắc lắm
Cái này mình chỉ làm thí nghiệm cho mọi người thôi
Nhưng máy lạnh cũng như sưởi
Nên dùng thừa công suất một chút thì đỡ tốn điện chứ dùng thiếu công suất thì tốn điện lắm mà cũng không hiệu quả
I am sorry but I tried to cool down my 50ltr tank with 3 peltier 12706 but the temperature is not decreasing after 27degree centigrade...
Help me with some information
hello there, I have been follow ur video and did everything same as you but I have been end up the temperature only drop for 0.4C(28 C room temp) for almost 1 hour and the hot water goes up to 40C, I wonder whats the problem actually
if the cooled water is flowed to the canister first, can it or no, sir?
what is the type Switching power supply you use, and what name the blue box ?? Thanks
That's the power supply 12v 20a
And the blue piece is Aluminum CPU Radiator Water Cooling
Piece of Paper Thanks Bro 👍
Sao bạn không làm sản phẩm thương mại và bán nhỉ? Mình sẽ là người mua đầu tiên.
Cảm ơn bạn nhiều nhé, mình làm thử nghiệm cho mọi người xem vậy thôi
Piece of Paper bạn có biết chỗ nào bán board mạch bạn thử nghiệm kg? Mình định làm thử
Nó là cảm biến đóng cắt nhiệt độ, nó có đóng cắt theo cả nóng và lạnh tùy mình cài đặt, cái mình dùng test thì rẻ thôi trước mình dùng cho lồng ấp gà bạn lên shopee sẽ có còn nếu dùng cho những thiết bị khác và dùng lâu dài thì nên mua cái tốt hơn
Hi.....I'm using 3 tec 12715 modules with 12v 20A power supply......the heating part found to be having too much heat even after using car coolant with water and a small radiator setup for cooling the coolant.....is that ok to run for more than an hour....???
You should use a larger cooling water tank to keep the temperature stable
The maximum temperature I measured was 45 degrees
@@pieceofpaper924 I'm now getting the max of 49degs.. Is that ok.... I'm using 1litre of water n car coolant mixture
@@pieceofpaper924 and may I know the size and volume of your scaped tank??
Approximately how long will it serve me ??
With only one of this blue radiator with three peltier and one pump to regulate the water won't work? i don't know if you understand me.
hello friend, excuse me if i got you wrong
but i think you have the same missunderstand that i had
he uses 2 blue radiator because one side cools the water and the other side warms the water
peltier works as one side of it getting cold and the other hot
Ive seen many projects where they use an fan or heat dissipator on the hot side
but it seems that also using water in the hot side works better
thats why he has 2 tanks of water. 1 gets cold and the other gets hot
hope i could make it clear
Yes
I just want to do a test on the types of radiators
I found it better to use water radiators
We can do more neatly during use
You must have a temperature controller like mine
The temperature controller controls the machine when the temperature exceeds the required level
I understand how the system works. I'm just saying that if a radiotor with its both sides have peltiers to cool water and the hot sides of peltier have heatsinks. Then you need only one pump to regulate the water. I have a diagram. Add me as a friend to send it to you!
What is the max temperature of the hot water produced ??will using automobile coolant cause a better radiation??
Great vedeo.Can you share the specs of power supply module.Also if the ciculation tank is placed 2 ft below the fish tank,than would you require a more powerful pump in it?