Just basic wrenches, sockets, and ratchets. I don't recall all the sizes off the top of my head. You can buy a cheap set of mechanics tools from Walmart for under $100. I bought my set of cheap Stanley crap for $87 seventeen years ago and I am still using it.
I'm curious if you're going to replace the hinges. Considering the impact on that door it's very plausible the hinges got tweaked. Though it's opening and shutting well with the damaged door the new one might not.
On the window issue. Hold the button down all the way. Wait for a click. Then hold the button down in the up position. Wait for the clock. That should reset your window for the smart motor system
This is a hydraulic version, they don't seem to have the yellow one that is impact operated: CCIYU Heavy Duty Car Door Installer and Remover Jack Lift Hoist Red a.co/d/7wFfdoo
Yes, I fixed the window. There is no module programming that I could locate. I removed the entire wiring harness, the motor/regulator and the actual window from the old door and installed in the new one. Everything works now.
Goodfellas Garage installed the door did not have to reinstall all my old Internals , I’ll find the link but there is a step procedure ghat you do thru the driver side by picking the window up and down in a sequence
@@LimitedEditionMotorcars I found your thread online, I think the 2018 has a different type of connectors, Ford makes it impossible to even run wires through there without drilling holes
@@arturorojas983 2018 has the same door, door panel, window, etc. You need to peel the rubber seal at the A-pillar and then you will see the harness plug.
@@arturorojas983 Use your fingers to press on the clip. There are also 2 tabs on each side of the hard frame that is attached to the A-pillar. You can use a small flat head to press them to pull the harness out which will give you some wiggle room.
This same EXACT thing happened. But they hit mine in a parking lot and did a hell of alot more damage. The window didnt shatter and the back wheel panel needs to be replaced as well unfortunately..... Deductible for the insurance company is wanting 2000 but the door was hit so hard that the window doesnt shut properly.
its basically wrong harness for your mustang ,you bought a door from a 2018+ which doors and windows controlled by door module ,as you see on your video there is no module on your old door because older mustangs door and windows controlled by bcm-b module which located at the right side of the trunk :) solution : remove door module and relocate pins according to your old harness ,vice versa !!
Tryna figure out if a 2021 GT door will fit on a 2017 GT
Did you ever figured it out? I have the same question
Wonderful video. I have the same issue except my mustang was hit hard on the left door and it won’t open at all. It’s a 2014. Any tips to get it open?
I am sorry, I have no idea how to open a stuck door after collision. You may want to consult with a professional. I have no idea what I am doing 😂
Great job! What were all the hand tools, and sizes you used to remove the door?
Just basic wrenches, sockets, and ratchets. I don't recall all the sizes off the top of my head. You can buy a cheap set of mechanics tools from Walmart for under $100. I bought my set of cheap Stanley crap for $87 seventeen years ago and I am still using it.
I'm curious if you're going to replace the hinges. Considering the impact on that door it's very plausible the hinges got tweaked. Though it's opening and shutting well with the damaged door the new one might not.
That's got to be the easiest door swap I've ever seen if you didn't have to do any adjusting and got the lines that tight
On the window issue. Hold the button down all the way. Wait for a click. Then hold the button down in the up position. Wait for the clock. That should reset your window for the smart motor system
What is the name of the yellow door tool thingy?
This is a hydraulic version, they don't seem to have the yellow one that is impact operated:
CCIYU Heavy Duty Car Door Installer and Remover Jack Lift Hoist Red a.co/d/7wFfdoo
Where you able to fix the window swing exact same install rn but haven’t gotten to the install yet didn’t think about reprogramming the door
Yes, I fixed the window. There is no module programming that I could locate. I removed the entire wiring harness, the motor/regulator and the actual window from the old door and installed in the new one. Everything works now.
Goodfellas Garage installed the door did not have to reinstall all my old Internals , I’ll find the link but there is a step procedure ghat you do thru the driver side by picking the window up and down in a sequence
@@JohnnAlaniz My door came off from a convertible I think so harness had extra modules and wiring. It took me 15 to swap it all over, no big deal.
will a 2018 door be compatible with my 2017 mustang?
where did you order the door handle? Thanks!
www.amazon.com/dp/B000KKJ40M/ref=cm_sw_r_apan_i_18B0C5A4KP6K87MWP96D?_encoding=UTF8&psc=1
Thank u so much
How did you take off the door wire hardness?
It unplugs right at the A pillar.
@@LimitedEditionMotorcars I found your thread online, I think the 2018 has a different type of connectors, Ford makes it impossible to even run wires through there without drilling holes
@@arturorojas983 2018 has the same door, door panel, window, etc. You need to peel the rubber seal at the A-pillar and then you will see the harness plug.
@@LimitedEditionMotorcars gotcha’ I see it! Thanks! What did you use to disconnect that harness plug?
@@arturorojas983 Use your fingers to press on the clip. There are also 2 tabs on each side of the hard frame that is attached to the A-pillar. You can use a small flat head to press them to pull the harness out which will give you some wiggle room.
What was the cost ?
The cost of what?
This same EXACT thing happened. But they hit mine in a parking lot and did a hell of alot more damage. The window didnt shatter and the back wheel panel needs to be replaced as well unfortunately..... Deductible for the insurance company is wanting 2000 but the door was hit so hard that the window doesnt shut properly.
its basically wrong harness for your mustang ,you bought a door from a 2018+ which doors and windows controlled by door module ,as you see on your video there is no module on your old door because older mustangs door and windows controlled by bcm-b module which located at the right side of the trunk :) solution : remove door module and relocate pins according to your old harness ,vice versa !!
Michael Jackson used the glove to keep finger print off of his crotch. Possibly others as well. Rip Michael.
Did you figure out the window?
Yes, I just transferred over the entire wiring harness and regulator/motor from the old door. Everything works now.
Do a video on that please
You need to repait it
What about the key lock
There is no key lock on the passenger door.