Easy Box Joint Jig | How To Make Box Joints
Вставка
- Опубліковано 10 чер 2024
- Easy Box Joint Jig | How to Make Box Joints
In this video I show you how to make and quick and easy Box Joint Jig that you can use over and over again to cut perfect Box Joints
Merchandise & Plans: www.bourbonmoth.com
Patreon Page: / bourbonmothwoodworking
Cameo: www.cameo.com/bourbonmoth
Instagram: / bourbonmoth
Links below to tools and supplies:
3M Cubitron Sandpaper: lddy.no/1hset
16 G Nailer: amzn.to/2KnhyUB
Clamps: amzn.to/2OjyYUh
Square: amzn.to/2tiTPQr
Tape Measure: amzn.to/3b2rnDq
Safety Glasses: amzn.to/2RMLoGv
Festool (or similar) Chop Saw: amzn.to/3zLXNia
Flip Stops: amzn.to/31MpydR
Table Saw Blade: amzn.to/2RJUCmI
Dado Stack: amzn.to/2KbRr2Q
Forstner Bit Set: amzn.to/2vQCUWw
Glue & accelerator: amzn.to/34LhtDw
Rubber Mallet: amzn.to/3elioPc
ISOtunes Bluetooth Hearing Protection (10% off code- BOURBONMOTH10) bit.ly/BourbonMoth10
Bits & Bits Precision Cutting Tools (10% off code- BOURBONBITS)
bitsbits.com/ref/6220/
RZ Mask (15% off code: BOURBONMOTH15)
www.awin1.com/cread.php?awinmi...
Total Boat Epoxy: (10% coupon code TOTALMOTH) www.totalboat.com
Nicks Handmade Boots: bit.ly/3vZ8uMR
Firm Grip Work Gloves: thd.co/3LEO5TE
PowerPro Fasteners: amzn.to/3u3Mgtj
Pony Jorgensen Clamps: bit.ly/3knr9fZ
Spec Ops Hammer: amzn.to/3fMjAOd
Spec Ops Tape Measure: amzn.to/3w1M788
Spec Ops Pry Bar: amzn.to/2Ro3iC2
Spec Ops Chisels: amzn.to/3ga8kKv
Spec Ops Screw Drivers: amzn.to/3ciV8ls
Spec ops utility Knife: amzn.to/3g5ysWZ
Grizzly Tools:
Table Saw: amzn.to/3q8Wbu6
Jointer: amzn.to/3gFHE6a
Planer: amzn.to/3xCzH7r
Dust Collector: amzn.to/35AFEWw
Air Filtration: amzn.to/3zyXXsK
Band Saw: amzn.to/3gEtCAm
Drill Press: amzn.to/3xvhxEh
Lathe: amzn.to/3vChWUb - Навчання та стиль
I want to express my appreciation for all your videos. Thru your work I was inspired to take up woodworking in June 2020. In 6 months I’ve gone from not knowing much and the art of woodworking to being able to build an entire kitchen of new custom cabinets. Now I’m starting to tackle taking on jobs from customers and building custom furniture. Thanks for helping me discover something that has forever transformed my life. God bless.
That’s awesome 🙌🏻🙌🏻
Damn my guy, great work! That’s my dream too. Inspired me to get going! Finishing up my workbench, then it’s go time.
@@Bourbonmoth I bought a dovetail rig and whilst I can join boards edge to edge, I cant make right angle joints, it can clamp both boards at right angles, but the top board stencil is 1.5"' away from the board and no way to rotate it (Like you need a route bit with a very long shaft), any ideas what this type of jig is and what its use is? It looks to be quite old and made in England.
@@Bourbonmoth couldn't you flip this jig around and use it in the opposite direction for a different size cut say 3/4" ? so this jig cuts 2 different size box joints
@@DeepSnowRider if he made one that cuts 3/8 box joints made the fence 3x3 glulam, made the base 3" wider than the fence, and eliminated the sides and back he could then use the jig to cut door stile tenon's without changing any settings. UA-cam Woodsmith finger joints, their jig makes quick work of variable pins with minimal chance of error, and the jig if planned right can come from a single 2'x2'x1/2" plywood.
This is without a doubt the best video on box joint jigs I’ve watched
Absolutely love your videos. I went out and bought a dovetail jig prior to watching this very simple build. I wish I'd seen this first.
I think I'll actually do this. Thanks.
That is the most user friendly box joint video I've ever watched. Everyone else makes it so complicated. Good job. Love your sense of humor also.
Go see William Ng, his box joint is a lot simpler and more accurate as well
I might never even use this, but the how-to is amazing. Perfectly understandable, even for a complete beginner. Explanations were super clear. Awesome work, and thank you for taking the time to create!!
I watched lots of videos of how to do the joints and I always felt that something was missing! Here you are explaining it! Thanks alot!
So satisfying!!! You should post a video of cutting and fitting together box joints exclusively. It’s so mesmerizing. I could watch it all day. 😊
This is exactly what a UA-cam channel should be. Fun, instructive, and totally useful. Great video. I am building my box joint jig right now!
Okaaay hero
00S0q000000011q
This guy is so freaking smart and funny, one of my favorite in UA-cam of not my favorite. 🤣👍👍👍👍👍
You sir are a great teacher! Thanks for making this so clear.
Wish I've seen this before very clean smart you're a great carpenter best of luck
Great video! I too learned about the simplified method for making repeated box joints and a bonus for the sled build. I have built additional sleds for crosscut and miter joints. I like having a dedicated sled for box joints and now I know how to thanks to your video. Sincere thanks and keep them coming. I'll be watching.
“Or end up in a Goodwill somewhere”😅😅. That’s how I feel about all the gifts I’ve made over the years. 😢. Thoroughly enjoy your videos, thank you
Everyday I get on UA-cam. And everyday I get this video recommended to me. Guess I’m learning how to make a jig
This was awesome! I learned 2 things from this- both how to make a saw sled and how to do the box joints. I haven’t seen a video explaining it so simply and well done! Thanks!
same!
@@jetlaggedchef6806 Just keep in mind that the front fence on a regular sled that's used for making longer cuts, should be more precisely squared than one like this one. On short cuts like this, precise 90º cuts aren't so critical.
Always entertains and always informative. So many videos like this one seem to make the project a little more difficult than it should be. However, Mr. Bourbon Moth talks you through it with good video and to the point verbal directions. I needed someone like him for my college calculus classes - calc is still very Dark Magic to me. Anyway, thank you for your quality presentation and describing the process simply. As always, well done!
So much more honest and transparent than TOH. Thanks!
I've been watching a number of videos on this technique. Yours is the only video I've seen which talks about and shows how the offsetting cuts are made and then fitted. In other videos it's just magic, you define/explain it well.
Thank you so much for posting this video. I have been watching your channel for some time now and made my first jig as a result of your instructions. It was challenging, frustrating, and so rewarding.
Wish I had seen a video like this back when I was running a woodworking hobby business. I did mine using a scroll saw with fine blades which took a long time and did not always fit tight like this one did. Thanks for teaching an old man something new.
Hey with your woodworking hobby business, how did that work? How did you start it? Did it cost you money to start up/run? Did you charge people to come & how much (may I ask)? How did it work, did you have a different topic taught each day? Or was it like a lab with free use of machines?
Great step-by-step! First time attempt was successful. Thank!
I like your sense of humor in your presentation.
Glad you showed how to make a box joint after and explained how it works with the little extra on the end. Made sense now. Great content. Big fan. Keep it coming.
Excellent video tutorial :-) I have just made something inspired by this to use with a router table as I don’t have a dado blade - it works perfectly! Thank you!
Amazing. I’m new so I’m thankful for this perfect explanation that a child could comprehend.
Cool. This is by far the easiest method I've seen to build a jig. I've never done box joints due to the complexity, but even an old Pipefitter can do it with your instruction Thanks, Bud.
I made one but made that tab longer so I can do 8 at a time - works great!
I've seen videos before on how to use a jig with a pin to make joints like this, but this is the first one I've seen that showed how to use the first board to align the mating board. Thank you! That makes it sooo much easier to understand!
A rare UA-cam shop video with actual sawdust in evidence.
Great video. I always learn something new watching your videos
Love the way you added the glides with glue!! Definitely using this method for future jigs!
Doesn't this result in a sled that isn't actually sitting on the table though? would it be better to cut the runners a little shy of the table and then install them with coins in the slots to raise them up while you glue?
Well done, this is a great video! Thank you.
Down at the first hurdle, I don't have a plywood stash. I do enjoy watching your expert supervision and your funny delivery. You are a really humorous man. Greetings from all us lady DIYer's in the UK. 🥰
best demo yet, cowboy thanks, 47 year carpenter
Amazing channel for someone like me just starting out in woodworking, but your humorous nature is what got me to subscribe 🤣
Same. I love these videos and the instructor is fantastic.
Seriously dude, one of the most informative and easy to watch videos ever! Keep up the good work
That's a badass jig.. thx for sharing. Much quicker way than using a dovetail jig.
I think your soft humor is terrific. It makes watching this enjoyable
A very impressive build. I absolutely love this jig, I am adding it to my To-Do list.
I am your new fan.
Thanks for sharing
It's awfully involved. I just screw a scrap of wood to my miter gauge with the pin in it. I also make the pin long enough that it can hold all 4 sides at once. Because pushing stock back and forth gets old real fast. Plus the joints come out more accurately if you cut them stacked all up at once too. I clamp my stacks together before I cut them. You still have to do the reversing deal before you stack all the sides up like is shown here. Then you set your stack up on the pin, clamp it all together and cut away.
@@1pcfred exactly what I did. Just made basically his back panel, a few in the common sizes I make. I do 2 sides at once.. I can't visualize how you're doing all 4 sides together and get them to line up right?
@@Turk380 You do the alternating face cuts first of course then stack them all on the pin and clamp them up together. I wrote an article about how I do it here www.instructables.com/How-to-Make-a-Box-Joint-Box/ I think they come out better stacked. It is certainly less back and forth.
This is wonderful. I built a sled similar to your other one (sans the front piece of aluminum...) and now I will be building a box joint jig too. Thank you as always for the awesome information.
Awesome. Crushed it again. Great education and entertainment.
That's actually very useful, and will save some money. Thanks!
Oh the back of Baltic birch plywood ALWAYS chipped off; even with tape! You guys deserve thumbs up just for making everything look easy. It’s like baking never looks as good as the pics when it’s done 🍺
Of course functionally it doesn't *really* matter for a shop jig, but there's nothing wrong with wanting your gear to look nice.
If the chip-out is going to bug you, just clamp a sacrificial piece of scrap to the back face of each chippable surface before you cut
(In this case, the inside face of the front fence and the outside face of the fence+base at the back of the sled).
It works way better than tape, especially if you can clamp close to the cutline (obvious disclaimer: NOT so close that you risk clamp/blade contact)
this is one of the sturdiest and simplest I've seen. I have found that moving the register peg a few thousandths closer to the blade before fixing the rear fence to the base reduces the peg width just enough to allow for the tightening of the joint caused by the glue. But I am generally making small boxes and using the kerf of my FTG blade instead of a dado stack, might not be an issue with such large fingers. Thanks for sharing, have some drawer boxes to make for the shop, will make myself one of these for sure.
Hi.. new subscriber here.. I'm from the philippines.. i love your videos! I'm a complete beginner, and learning a lot. I just wanna say thank you and keep on making videos.. good bless!
You just earned yourself a subscriber
I went by your instructions on the jig assembly and I will was amazed. I think I spent more time playing with my datto stack than building the sled. You definitely need to get the stack to match your tooth. My first scrap 4” joint came out perfect and tight. Now it’s time to build some drawers. Thank you for the great video. Wish I could post a picture of my joint.
Great video, liked the sled and your design ( very simple) and comfortable to use. And it's good to have good humor!!! it's a woodworking show not a grammar lesson
Loves these videos and the dry humour! Keep up the good work 💪👍
I'm amazed. Thanks for such a great video.
That is an awesome project. It turned out amazingly smooth and did a great job. Thanks for sharing your knowledge and wisdom.
Hey, I wanted to start off by saying that I LOVE your videos. I am brand new to wood working and so far I have learned tons of diffrent things from you. Keep up the amazing videos and keep inspiring thousands like me! Cheers!!
Hello i'm Martin from Bavaria, i see allways your videos. Your explanations work well for me, thanks for this. You've done a very great job. I've already learned a lot about it.
Best wishes from Bavaria, for you and the family all the best.
RESPECT from Martin. 🍀🍀🍀🍀👍👍👍👍💪💪💪💪🤜🤛🤜🤛
Good work man from the UK 🇬🇧
I did it, and it didn’t even hurt! Thanks for the great tutorial!
Bro you just made me a believer. I like the energy. New woodworker and this video gave me a feeling of triumph. Good shit💪🏿💪🏿
I was always curious how this was done, but I appreciate you taking the time to really do a thorough explanation.
Your way of describing the work makes it easy to understand, and you make the videos a bit of fun to watch... Can't wait to try these box joints!!!
You are one of the best teachers on the internet, your builds are always so easy to replicate
Love your videos, man. I know you asked what we'd like to see from you a while back, here's mine :) Would love to see a video of how you start a project from request through measurements, to sketch and how you figure out how much lumber you need to the start of the build.
You, of all people, could make that interesting and engaging 😄
Love it! Most simplistic jig yet! Awesome many thanks!
Smart method and funny presentation most appreciated. Thanks!
I have the same jig! It's amazing! Thank-you for the great video!
Great! Something else added to my list of things I need to do!! 👍🏼
Great Video! You make the difficult look EZ! Thanks.
Just superb, and brilliantly presented. Gawd bless ya!
I never realized how much jig making goes into woodworking.
I have a few fixtures to help, I was a machinist and then an Aircraft Jig / toolmaker. So I am always thinking from the tooling perspective. If your going to perform repeatable operations it’s the only way to go. Box joints, dovetails, splines, and evening holding fixtures are great ideas.
Clay Mango all aspects of woodworking inc whittling
You'll make more jigs than projects. If you're serious, find a local source of Baltic birch plywood.
"ooooh box joints" lol so snarky love it. now if only i had a table saw....
and a dado blade. (note to self; buy that dado blade set you always wanted.)
Always nice to watch you work
Love this video. Thank you for this great jig.
Needed this! I’m getting things together so I can make my own bee hives. Thanks a bunch!
hey man, ive found that a simple rabbet joint is way strong enough for hives (mine are still going strong after 10+ years). No need to put the extra work in, just use high quality wood, not anything with glue and multiple layers! Also waterproof wood glue helps a lot lol, believe me the normal wood glue isnt waterproof (bad mistake). Cheers and happy beekeeping!
That's nice!! It takes me forever to make something like this since I have to do cuts like this with a dremel tool due to my lack of functioning arm/leg.
You make it look so easy! That's the sign of a good craftsman! I'm a Master Electrician but I'm a newbie to woodworking. I'm disabled due to illness (Cancer, etc...) so I needed something to make me feel productive and woodworking was the answer! Your videos are awesome! BE SAFE,GOD BLESS!🇺🇸🙏❤
Excellent video. Very helpful. Thank you.
This is a great!! A very well demonstrated video. You did a wonderful job. Your instructions were clear. Your arm being in the way is not an issue. I also like you art and the name of your company is very creative. I have subscribed and look forward to you helping me with my next project. (I have to finish my chicken coop first - Cackleberry Castle)
I like the super glue and activator trick. Pretty slick there bradda!
Very nice - good clear video and description. Thank you.
Absolutely SICK! thanks man for the video!
A longer peg would allow you to cut multiple boards at the same time. You could even have the peg going all the way to the other end of the box. Great video, thanks for sharing.
Because he didn't square the back fence, any error will be multiplied the more boards are stacked in front of the first.
@@veritasestveritas8646 Still a good idea/ iterative step though. Soon we'll all be making our own furniture again. lol!
VeritasEstVeritas I agree, for 1* error is .017 of an inch degree difference. That adds up quickly especially if you multiple the degree error.
Great idea
@@texasfossilguy All should be well as long as that long peg/batten runs parallel with the rip blade slot and rip fence. But the effort needed to set all the additional work pieces probably wont save much time. And we can be sure that one(?) will shift while cutting slots.
Thanks for this! A slightly different take on others I've seen before. That's quite alright though and like how you did this. Will have to build me one!
You videos are incredible source of knowledge making me love woodworking even more...Thank you!
The bomb bro! I’m on it. I’ll be a pattern when I get back out to my garage…
That intro!
That voice.
Instantly subbed.
It really brings it "together"!
Your good and funny 👏,👍
Thank you, I’ve now dare to buy and use a date stack. You are the coolest. Thank you for taking the time to explain, record and entertain. You are my favorite home on UA-cam.
Nothing short of genius; perfection in least number of parts and operations. I'm going to steal your ideas. Many thanks.
Great video! Now do one for people with a saw that doesn’t accept dado stacks 🙂
Yes please!
Just get a real saw.
@@Rowgue51 dados not allowed in Germany, unfortunatelly ;)
@@fraensemeier-fotografie
Just order a real saw from somewhere not Germany. It's not like the cops are going to be going door to door busting people with illegal saw blades.
@@fraensemeier-fotografie Wait, seriously?
You make my day and I finally decided to make my first cabinet, I am extremely intimidated but you make wood working seem so easy, I just got to try it. Heck, I got most of the tools just too afraid. Thanks for inspiring me.
AMEN!
Stop being scared and get on with it. Safety first of course.
Awesome thanks. building box joint sled tomorrow
So simple yet elegant! You Rock!
All I need now is a decent table saw.😂😂
For real .
I'm sure you can do this on a cheap saw with a decent base. The major difference between an cabinet saw and a portable contractor saw is the weight. The weight helps keep the vibrations down.
I used a 1½hp saw for YEARS in my business and got awesome results
Or a Festool gliding miter saw and a Festool shopvac. LOL
Same
Dammm true
Great video and tutorial. Just wonder, however, why make it into a box as opposed to a 'standard' table saw sled with a modified front fence? Is it to help keep the fence perfectly vertical?
Best box joint jig i have ever seen. Simply brilliant.
Thank you. Definitely an inspiration.
Great video! Wondering if you can make a future video of cabinet carcasses and face frames? Thanks
Yes indeed
@@Bourbonmoth This I very much want to see. I really want to build my own kitchen cabinets.
They came out absolutely nice wow!must try some of these when i get chance on hand,thank you sire😉🤞
Thank you for the explanation. Concise and no fluff! Appreciate the sharing of your knowledge.
Well done. Well done. Great attitude = great work.
Dude.. man crush happening right now.. that was brilliant bro!!