I went to school for this stuff 30 yrs ago. Now I guess I am going to have to start using my skills again to fix these machines. Thank you for videos. So much help for me to see the great work you do. Awesome 👍👏❤️👍👏❤️👍👏❤️👍👏❤️👍👏❤️
Thank you very much sir you have told how to insert hall sensor in full detail I have learned a lot from your video but you have not told which number of hall sensor are and unipolar is bi polar
Thank you very much sir for your reply actually I am also an electric bike repairing mechanic so I have a hub motor i scooty for sensor problem so when I put the sensor in it unique polar 44 e now the motor started jerking. No, one of its center sensor was saved, the rest was broken, so when I checked it, what is its function, South Full North. What does rotating the full magnet do? I found out that now the bipolar sensor will be installed in the motor. Then I put 41 F and activated it. Now the story will be long. Thanks for your reply
Hello sir .perfect job I like it but I have one question pls the board it broke so I try to connect all the sensors Sam your way my question it is work 41f sensor if I connect it same this way too ?
Hello sir. Yes can be like this method. But befor you remove the hall sensors check first the color of sensor wire yellow-green-blue or you can take picture so you not mistake.
@@ricodaray I would like to ask u sir Rico I bought new controller but when I connect it with out I use the throttle start run the motor brushless spical when I connect the smart cable
What is the use of sensor there, and which one supplies current to the stator? Kindly make a video that explains the principle of operation of such ebike. Thanks
Good day Sir... ano problem ng battery ebike ko..? ginamit ko ung spare battery ko.. actually na stock sya during pandemic..sinukat ko ang voltage 2.8 ung apat..ginamitan ko sya ng foxsur multifunction charger..bakit nagregister agad full samantalang 5v pa lang..anong status ng battery ko Sir..? Salamat uli sir
At 7:00 Min I question when the stator windings get hot if the electrical tape adhesive will melt and loosen? I might suggest using small heat shrink tubing over each hall sensor lead, and/or potting them in high-temp silicone RTV. Also, once apart, cleaning and painting the insides of the motor housing and painting them with flat black corrosion inhibiting paint is supposed to improve heat transfer, and I might suggest 'first-timers' be carfule not to damage the windings with sandpaper. Some advocate also coating the magnets and and windings with paint like protective electric motor compound to prevent corrosion but non-conductive, non-Lithium base grease might be help to prevent corrosion too. BTW, have you tried using automatic transmission fluid or Ferro-magnetic fluid inside the motor to improve cooling and inhibit corrosion and rust? I see it used in several videos, but question if that could cause shorting issues with the Hall sensors?
Thank you sir. Im not rich and i don't have to all that you named. But i only doing a simple hack that can run yuor motor in a simple way, in a very small coast.
HAELLO ,how did you put these hall sensor all with the inscription up baceuse they say that the middle one should be mounted with the inscription down as you installed.
Hello sir, some of hub motor the middle one of hall sensor is downward and the other also is upward. So before you remove the hall sensor check first and notice the correct placement to avoid errors.
Sir nag auto sensorless ang controller kay na detect na daot ang hall sensor. Dapat ipa repair ang hall sensor kay may tendency na masunog imong motor kay wala nay protection.
Awesome video, My bikes wire got cut where it enters through the axle. What is the name of that wire . I can't find it anywhere online . I know its the hall sensor and phase wires and i can find the part that connects to the controller but i can't find the part that actually goes through the axle..
@@ricodaray I couldn't find just the wire. Seemed like no one is selling it without the motor but, you showed me what I needed..I'll try to repair it with the new wire, Then when I'm done making the bike worse, I'll find out i need a new motor anyway lol..
Tsek ko sya Sir Rico na may voltage 5 volts bawat Isa pero walang reaction pag inikot ang gulong..gaya ng napanood ko sa vlog mo na may reaction pag inikot mo ang motor...ung sa akin steady sya walang reaction.. possible na ba na defective na ung hall sensor.. salamat uli sir Rico sa pagsagot.. magandang araw po
Matamoros ng code para sa ebike sir. Gamit ko po ay hall sensor 413 sa lahat ng motor na ginagawa ko. Pero maraming hall sensor makikita sa shoppe at lazada. Basta ba pang BLDC motor hall sensor pwede po
@@ricodaray yong alternator sir gawing brushless direct current 3 phase motor sya pag maiconvert nagsearch po ako dto sa youtube sa video ko lang nakita yong connection ng hall sensor
At ung nabili namin na hall sensor ay plate po ? Lima lang po ang terminal at di namin ma pa andar ayaw , ano po ang tamang bilhin ung walang plate tulad ng pinakita nyo sa inyong demonstration?
Sir, after change all three sensors, the motor make buzzing sound at starting...when going fast, the buzzing sound become slower. Is that because of new hall sensor didn't match the original one?
@@poginani7951 yan pang po nala lagay sa hall sensor na supply namin. Yung sa shoppe at lazada same lang din yun basta hall sensor ng bldc motor. Ibang yung code pero same lang ng trabaho.
@@ricodaray maraming slamat sir nakita ko na din ung link na binigay mo at nakita ko ung diagram at nag tester na ako ng naka lagay na hall sensor ko at base don sa diagram don sa link tlagang may tama ung isang hall sensor ko nag tester ako ng kalas ang hinang ng hall sensor ung ikatlong sensor ko alang palo sa tester
Hello po sir. Question lng po bka my idea kayo ano part number ng hall sensor/transistor ng Fiido D2S? Motor number 36V250W21E0320 (FIIDO F4S 3C) ngtry n dn ako mgpalit take chance ng 49F Bipolar at 49E linear pero d p dn gumana.salamat po sa sagot
Hello po. Naka depende yan sa controller. Pagka bukas mo ng motor tatandaan mo agad yung color code. Pero pag nag palit ng ibang controller need e configure para ma hanap mo tamang connection. Trial and error yung gagawin like balibaliktarin lang yung wire ng hall sensor para ma kuha yung tama
Can you get rid of the hall sensors and bypass the cables on the 48v brushless motor? If yes how can you bypass the wires? Does the yellow and red will be joined together? also the blue and red and the green and red. And all 3 black cables together. Does the motor work without the sensors?
sir, isa rin b ito n rason, kung bakit ung ebike ng asawa ko, bigla bigla n lng nag shut down, tas mag on nmn sya ulit.. pina check n nmin ung battery ok nmn daw lahat.. thank u and God Bless po
Pag namamatay yung ebike walang kinalaman ang hall sensor po. Kung OK naman battery mo, check mo po yung fuse, breaker kung may breaker, mga terminal at socket baka may maluluwag lang kaya namamatay.
Hello sir. Some scooters display M warning, it means motor have problem. Some also display code error. But you can check to your manual to verify what error for M
about to do the same to a almost new ebike , BUT one of my hall sensors are turning - what i think - the wrong way ! the other directions of the 2 others . the one i got in the middle has the ....smallest surface turning against the axl if you know what i mean . have you ever seen that or do you as i - think that has always made the bike run strange !
@@ricodaray IT was sitting right, i could se + and - was right to the sensor ....Strange BUT i dont get the 6volt signal so IT is bad. Thanks to guys like you i dont have to use All my familys money
@@ricodaray hey Rico...can you please give me a link to thoose hall sensors YOU use ...just replaced em, but now it gives me error code 3 " hall sensor " im not sure i got the right ....fuck
Sir I'm working in electric bike company so we have enough supply of parts. But here in Philippines we have LAZADA.com that we can order through online like this s.lazada.com.ph/s.3Nqvj
@@ricodaray thanks...i got the store here in denmark , BUT is there a differnce in the sensors if its a 24 volt or a 36 or even higher ? i can get the hooneywell ss41 24 volt, but my battery is 36 volt, but that shouldnt be a problem you think ?
its ez to replace but have no idea which type of sensor should buy, in my case my middle hall sensor has the different model than left and right sensor ,
@@ricodaray with this link there are many sensors with middle one different from side ones and also has to consider wattage of the motor and does the sensor can survive under high temperature or not,
Question lang po sir nagpalit ako ng hall sensor okay naman voltage reading ng dalawa ( blue and green )5v pero yon isang yellow 3.90v lang okay lang po ba to? Or need ko palitan ulit yong hall sa yellow?
Hello po sir. Dapat same lang yung voltage kasi isa lang source nila galing sa controller. Baka sa wire lang may problima. Pero try mo paandarin kung gagana sir.
Sir my access125 converted electric scooter 67v 800w hub motor But recently hall sensor defective sir N41 909 This hall sensor not available in market so any alternative is suitable Give me replay sir thankq
@@ricodaray Hello sir i have à citycoco bike,my contrôler is ok but my motor doesnt work ,What can i do,in thé first ans second etc thank you very much for your working ,
are hall sensor problems always noisy when it is not working? reason I ask is both motors cut out on my dual hub scooter. It happens when on hot day and full throttle. there is no strange noises or wierd sounds. All power is gone. this just happens when in dual mode, when just in single mode with rear wheel, I have no problem. Please help. thank you.
Hello, if noisy some problem is the controller, but mostly if noisy is because of hall sensors. Check also the hall sensors if install properly. Check also the alignment of magnet and hall sensor. If hall sensors far from the magnet also cause nof noisy.
@@ricodaray thank you!!! This is so helpful. but i forgot to say when typing my question that mine is not noisy. So what does no noisy tell you? what could that mean? So logic says its probably not a hall sensor. But I'm confused about the controller. because when i see videos most people talk of controllers burning up and not working at all, all of a sudden and then broken and need to be repaired or replaced. I do not see any videos with my problem happening that i can find where it cuts off with no noise and then works again when i let throttle go back to nothing. I do not need to turn off the power or the key or do anything like that. but my problem is only on a hot day and when Im trying to do full throttle and then the motors cut off, with no noise, and no power. then if I bring the thumb throttle back all the way to 0 the motors work again if i am gentle. I can get 3/4 throttle and go 25mph (38kph) but i cannot make the full speed i otherwise used to make. about 33mph or 53kpph, but i cannot do that when it is hot outside or both motors shut off. If a battery overheated the bms shuts down then I think it would take time to cool off, but my scooter keeps going and take no time to reset by simply letting the throttle return all the way to 0 current. if I take easy on speed or if i only use rear motor on single drive setting there is no shut down and the scooter can get me home on dual drive. BUT if i try to go very fast in dual mode this problem will happen, only on hotter weather days. it is quiet with no strange abnormal noises. How do i know if it is controller or problem with battery or bms? What does no noise mean? THANK YOU THANK YOU THANK YOU!!!!!!!!!!!
boss tanong lng... ok lng bah nah 7k watts yung motor hub tapos 3k watts lng yung controller or need mas malaki yung wattage ng controller kaysa motor hub?
Hello po. Pwede naman po kasi naka depende sa controller yung ikot ng motor, kaso de maka perform ng sagad yung hub kasi hanggang 3kw lang yung bigay ng controller. At ang disadvantage is kung sino yung mababa ang power yun ang maunang masira. Mas maganda talaga pag pantay lang.
Rico Daray okay boss salamat nang marami..... more videos po lalo nat mga installation or upgrading ng ebike lalo nat sa mga tamang specs sa pag upgrade dami nyo pong matulungan po boss... God bless always boss...
So hard to find same number but can replace it any hall sensor as long as for BLDC motor. Now I'm using 413 but i use it to any kind of ebike and strike here in Philippines.
Salamat sa info kabayan. marami akong natutunan sa iyo. more bliessings to you Sir Rico.
Salamat po
Thank you idol gandin din sa hub ko walang board,hinfi ko napictirsn nong a cut na,, buti nlang may tutorial ka nito
Depende po sa hub. Pag ayaw gumana pwede mo pag baliktarin yung yellow green at blue hanggang makuha mo yung Tamang connection sir
I went to school for this stuff 30 yrs ago.
Now I guess I am going to have to start using my skills again to fix these machines.
Thank you for videos.
So much help for me to see the great work you do.
Awesome
👍👏❤️👍👏❤️👍👏❤️👍👏❤️👍👏❤️
Welcome sir. Thank you also for watching my video 😊😊
Nice! Iba tlga kpg si kuya rico ang gumagawa kaya san pa kayo? Kundi pagawa nyo na ebike nyo kay kuya rico astig!
Galing mo Sir, gusto ko sana ma try mo na ibalik sa e bike yung gulong, thank you
Sige po next time pag may aayusin po ako
Wow. Thank you for the knowledge sir!!💪💪💪
Tnx po
Brother, salamat sa mga munting kaalaman na binabahagi mo. Ako na mismo gumagawa ng e bike ko.
Thank you sir
Was looking on how to connect them directly. Love you
Thank you 😊
Nice video sir, please upload more video like this.
Salamat sir
I'm in New Jersey where you can buy the sensors
I have finally found something that impresses me on the net .
That spring as a tool , genius ,
Thank you so much sir, that spring is my buddy, i use it in so many ways and also fix flat tires like this
ua-cam.com/video/y1V5Ls5j-xk/v-deo.html
New Jersey where you buy the sensors where do you buy the sensors
Thank you very much sir you have told how to insert hall sensor in full detail I have learned a lot from your video but you have not told which number of hall sensor are and unipolar is bi polar
Most of ebike i have repair is using a Bipolar hall effect sensor
Thank you very much sir for your reply actually I am also an electric bike repairing mechanic so I have a hub motor i scooty for sensor problem so when I put the sensor in it unique polar 44 e now the motor started jerking. No, one of its center sensor was saved, the rest was broken, so when I checked it, what is its function, South Full North.
What does rotating the full magnet do? I found out that now the bipolar sensor will be installed in the motor. Then I put 41 F and activated it. Now the story will be long. Thanks for your reply
San po shop ninyo. Marami salamat po..
Wala po ako shop. Employee po ako mg Nwow ebike
Thank you sir sa pagshare ng videong eto ingat palagi God bless
wow congrats po sir grabe
Salamat po ma'am Ana😊😊
السلام عليكم الله يعطيك الصحة ويبارك فيك رمضان مبارك كريم slt merci beaucoup pour les informations et bon ramadan
Hello sir. If you have something to tell please it in english so i can help you. Thank you
Hello sir .perfect job I like it but I have one question pls the board it broke so I try to connect all the sensors Sam your way my question it is work 41f sensor if I connect it same this way too ?
Hello sir. Yes can be like this method. But befor you remove the hall sensors check first the color of sensor wire yellow-green-blue or you can take picture so you not mistake.
@@ricodaray I will just remove the board and I will contact the cable same your way
That's good, Make sure you will not mistake to yellow green and blue wire sir
@@ricodaray I would like to ask u sir Rico I bought new controller but when I connect it with out I use the throttle start run the motor brushless spical when I connect the smart cable
which sensor is going to work ? n need different sensors for different motors?
Thank you so much for your teaching..
Also thank you for watching my video
HI ,i 'm from México , Thanks for share !!!
Thank you sir
sir thank you sa video
Welcome po🙂
What is the use of sensor there, and which one supplies current to the stator? Kindly make a video that explains the principle of operation of such ebike. Thanks
The 3 phase wire is for high current. And the hall sensor is to controll the rotation of the motor
Sir Nice Vidio Tansistor noumber plase seand
Sorry late reply, I'm using hall sensor 413 sir
Good day Sir..ask ko lang po ano po ang value ng 3 transistor hall sensor sa ebike..? Wait ko po ang reply... salamat po Sir... merry Christmas 🎄🎄🎄🎄
Hello po. 413 po yung gamit ko. Pero kahit ano basta pang ebike hall sensor for bldc motorr pwede po.
s.lazada.com.ph/s.gOn1U
Maraming salamat po Sir... God bless merry Christmas 🎄🎄🎄🎄
@@ernestotamondong9283 salamat po sir
Good day Sir... ano problem ng battery ebike ko..? ginamit ko ung spare battery ko.. actually na stock sya during pandemic..sinukat ko ang voltage 2.8 ung apat..ginamitan ko sya ng foxsur multifunction charger..bakit nagregister agad full samantalang 5v pa lang..anong status ng battery ko Sir..? Salamat uli sir
At 7:00 Min I question when the stator windings get hot if the electrical tape adhesive will melt and loosen? I might suggest using small heat shrink tubing over each hall sensor lead, and/or potting them in high-temp silicone RTV. Also, once apart, cleaning and painting the insides of the motor housing and painting them with flat black corrosion inhibiting paint is supposed to improve heat transfer, and I might suggest 'first-timers' be carfule not to damage the windings with sandpaper.
Some advocate also coating the magnets and and windings with paint like protective electric motor compound to prevent corrosion but non-conductive, non-Lithium base grease might be help to prevent corrosion too.
BTW, have you tried using automatic transmission fluid or Ferro-magnetic fluid inside the motor to improve cooling and inhibit corrosion and rust? I see it used in several videos, but question if that could cause shorting issues with the Hall sensors?
Thank you sir. Im not rich and i don't have to all that you named. But i only doing a simple hack that can run yuor motor in a simple way, in a very small coast.
In this method, i already proven and tested for all most 10yrs in service of this electric bike.
Here we see those that talk. And those that do.
Where do you buy sensors for ebike hub
@@barryalexander6087 amazon, CA has them. Very cheap
Great video.
Question…does it matter if the hall sensor replacement is unipolar or bipolar?
Can’t find any information online or on UA-cam.
/Bklyn👑
I'm sorry i don't know also if unipolar or bipolar as long as the description is hall effect sensore for BLDC motor. Try this s.lazada.com.ph/s.UpVzK
I think it is a Hall Effect Device can not be replaced with ujt or bjt
Love from india🇮🇳 🙏💪
Thank you so much sir
ang pogi ng mechanic =)
Salamat🤣🤣🤣
HAELLO ,how did you put these hall sensor all with the inscription up baceuse they say that the middle one should be mounted with the inscription down as you installed.
Hello sir, some of hub motor the middle one of hall sensor is downward and the other also is upward. So before you remove the hall sensor check first and notice the correct placement to avoid errors.
sir ok ra na dli na itaod ang hall sensor socket.. goods man iyang andar.. bag o na iya controller guba na ang stock controller niya
Sir nag auto sensorless ang controller kay na detect na daot ang hall sensor. Dapat ipa repair ang hall sensor kay may tendency na masunog imong motor kay wala nay protection.
It’s a tough work if you don’t have any patience you can’t be in this kind of work or job! Keep it up.done full support with ads
Super explain thank you sir ❤
Thank you for watching sir
Salamat idol
Salamat din po sa panunood sir
ang liliit pla ng transistor nya dpat nilagay mo name ng bwat wire ksi minsan ang transistor may npn pnp pero mostly g- ground pg dc current.
Hall effect sensor po yan na kabilang din ng transistor na pang BLDC motor at ang connection ay (positive-negative-signal)
Bon travail merci beaucoup
You are welcome sir😊 thank you also for watching 😊😊
Nice tutorial video
Thank you
Very useful video👍
Awesome video, My bikes wire got cut where it enters through the axle. What is the name of that wire . I can't find it anywhere online . I know its the hall sensor and phase wires and i can find the part that connects to the controller but i can't find the part that actually goes through the axle..
Here in Philippines we that motor hub wire. Try to look this one if this is the one you finding
s.lazada.com.ph/s.fA5RX
@@ricodaray Dude, Thank you soo much.. I can find every other cable but I can't find the wire in the axle without the Motor. Thank You
@@Keeganismyfirstname the link i send to you is only the wire for hub motor sir . you don't need to buy the motor 😊
@@ricodaray I couldn't find just the wire. Seemed like no one is selling it without the motor but, you showed me what I needed..I'll try to repair it with the new wire, Then when I'm done making the bike worse, I'll find out i need a new motor anyway lol..
ua-cam.com/play/PLKYJDVsQrRCqnO1GW1YCPp3lVjX3L3HGK.html
Good am sir,rico ask ko lng po yun hall sensor kinabit mo sa dynamo sa slot nya baliktaran yan sir harap man o likod ng hall sensor.thanks
Hindi po sir may petern naman po. Di mo masalpak pag baliktad. Yung likod naka kanto at yung harap may tapyas at dun naka lagay yung number
@@ricodaray thanks po at pagtama Ang kabit sa slot tapatan Ang Hinang sa board pag individual lng kabit Ng sensor
Sir can u plz make another video of this motor diagram and winding.
I'm sorry i don't know how to rewinding this motor sir.
Top seu trabalho !!! Abraço amigo SC - Brasil mais um inscrito
English please🙂
(top) = very good your work a hug from one more subscriber. Santa Catarina Brazil
Thank you sir❤️❤️
Idol ano bagay na number sa hall sensor na 2 wheels ang dapat ipalit ?
Marami sa shopee at Lazada basta hall sensor pang ebike or etrike pareho lang po
Good day Sir Rico..ask ko lang wat value ng 3 hall transistor..? same po ba ang value or number ng 3 transistor..?salamat sir sa pagsagot..
If walang reading sir, sira na po yun
Tsek ko sya Sir Rico na may voltage 5 volts bawat Isa pero walang reaction pag inikot ang gulong..gaya ng napanood ko sa vlog mo na may reaction pag inikot mo ang motor...ung sa akin steady sya walang reaction.. possible na ba na defective na ung hall sensor.. salamat uli sir Rico sa pagsagot.. magandang araw po
sir yung nwows ars po ba pwede siyang idifferential motor mas maganda po ba siya sa akytan kasi naka kadena?
Di po sya naka design ng differential sir
Hello po, baka may idea po kau kung anong code usually ang magnetic hall sensor ng V8 Mitsushi ebike?
Matamoros ng code para sa ebike sir. Gamit ko po ay hall sensor 413 sa lahat ng motor na ginagawa ko. Pero maraming hall sensor makikita sa shoppe at lazada. Basta ba pang BLDC motor hall sensor pwede po
Sensar kanha milega okinawa praise model ka please batade
English please
sana sir my nilagay mo sa video ung value ng transistor...
Hall sensor #413 gamit ko sir.
Dun sa Isang video ko naka lagay na kasi sa thumbnail sir
Sir parehas lng b na transistor ginagamit sa hub motor tsaka sa differential?
Hello po. Yes po same lang po sila sir
sir, pare-pareho lang po ba ang transistor nang ebike??
Same lang sir basta pang hall sensor ng ebike
@@ricodaray yung nakaboard na nabibili nya n sir?
hi.can i use 3144 unipoler hall sensor for this?
As long as hall sensor for bldc motor can be
I have more tutorial sir
ua-cam.com/play/PLKYJDVsQrRCqnO1GW1YCPp3lVjX3L3HGK.html
Sir,anu po ang pwede na transistor sa QS hub na 3000w?
Sir maraming code ang mga transistor. Kahit di same ng code sa original basta hall sensor for bldc motor pwede po sir.
s.lazada.com.ph/s.ffM3r
Upload k nga sir ng bldc alternator n lagyan ng hall sensor ty.
sensya na lods, ano po yung bldc? de mo ma gets
@@ricodaray yong alternator sir gawing brushless direct current 3 phase motor sya pag maiconvert nagsearch po ako dto sa youtube sa video ko lang nakita yong connection ng hall sensor
@@junifferjardinez4851 ah ok po. De pa na try sir. Salamat sa suggestion
subbed! sang unit po yang bldc hub na ni repair nyo boss? thanks!
Sorry late reply, sa nwow EP electric pedicab yan sir
Anong transistor ginamit mo pampalit jan sir
Hall sensor 413 gamit ko sir
@@ricodaray pede po ba yang sa e scooter na same value at same na paa doon sa binanggit mo sa isang video mo sir
@@ricodaray pamilyar po ba kayo sa 942 transistor
@@johncarlobernardo866 di po sir. Di pa ako naka gamit nyan
Pwde po ba ito pamalit 413 sa sensor na nasira ko 2wheels ebike jx213-60°?
Pwede po sir
Yan po ba ang tinatawag na boardless?
Pare pare po ba ang hall sensor ng two wheels pero 48 volts at ung three wheels ay 48 volts din?
At ung nabili namin na hall sensor ay plate po ? Lima lang po ang terminal at di namin ma pa andar ayaw , ano po ang tamang bilhin ung walang plate tulad ng pinakita nyo sa inyong demonstration?
Yes po same lang yung hall sensor. Pero maka iba yung porma ng board.
pare pareho po ba ng terminal configuration yung transistor nito hindi nag babago bago kulay ng wiring? thanks
Hello po, di po pare pariho naka dependi po sa controller. Kaya pag nag palit ka ng controller need mo pag palit palitin yung color code ng motor wire
@@ricodaray salamat sir sana magka tutorial din kung paano malaman yung kulay
Can use this method for all kind of BLDC motor sir?
Hello. Yes can be. But the yellow blue green wire are not same. You need trial and error testing to find out the correct combination.
@@ricodaray owhhh...ok2...
Tqvm sir🙏
Sir, after change all three sensors, the motor make buzzing sound at starting...when going fast, the buzzing sound become slower. Is that because of new hall sensor didn't match the original one?
Curious lng ako sir pwede rn ba ciang idiretso sa board…. Ano po bng value ung ginamit diode sir…." Slamat po
Yes po pwede naman gumamit ng board. De po yan diod sir. Tawag po nyan ay hall effect sensor 413.
@@ricodaray 413 lang ba talaga sir nakalagay sa hall sensor nya parang alang lagay sa shoppe at lazada
@@poginani7951 yan pang po nala lagay sa hall sensor na supply namin. Yung sa shoppe at lazada same lang din yun basta hall sensor ng bldc motor. Ibang yung code pero same lang ng trabaho.
@@ricodaray maraming slamat sir nakita ko na din ung link na binigay mo at nakita ko ung diagram at nag tester na ako ng naka lagay na hall sensor ko at base don sa diagram don sa link tlagang may tama ung isang hall sensor ko nag tester ako ng kalas ang hinang ng hall sensor ung ikatlong sensor ko alang palo sa tester
@@poginani7951 salamat din po sir
Hello po sir. Question lng po bka my idea kayo ano part number ng hall sensor/transistor ng Fiido D2S? Motor number 36V250W21E0320 (FIIDO F4S 3C) ngtry n dn ako mgpalit take chance ng 49F Bipolar at 49E linear pero d p dn gumana.salamat po sa sagot
Hello sir. Wala po ako idea kasi dipa pa ako naka gawa ng ganyan sir
lighter fluid sir ok lang ba na panlinis sa hub?
Di ko pa na try, pero i think pwede sir.
I'm in New Jersey where do you buy the sensors
Hello sir, here in Philippines we can buy in lazada s.lazada.com.ph/s.3nZ7j but maybe you can buy this in Amazon but i don't have link🙂.
@@ricodaray don't have it in Amazon
Sir need po bah talaga na yellow green blue.. dipo bah sia iikot pag nagkabaligtad un.? Salamat sir..
Hello po. Naka depende yan sa controller. Pagka bukas mo ng motor tatandaan mo agad yung color code. Pero pag nag palit ng ibang controller need e configure para ma hanap mo tamang connection. Trial and error yung gagawin like balibaliktarin lang yung wire ng hall sensor para ma kuha yung tama
Can you get rid of the hall sensors and bypass the cables on the 48v brushless motor? If yes how can you bypass the wires? Does the yellow and red will be joined together? also the blue and red and the green and red. And all 3 black cables together. Does the motor work without the sensors?
You cannot join together the cable sir
@@ricodaray Thanks for your reply
sir, isa rin b ito n rason, kung bakit ung ebike ng asawa ko, bigla bigla n lng nag shut down, tas mag on nmn sya ulit.. pina check n nmin ung battery ok nmn daw lahat..
thank u and God Bless po
Pag namamatay yung ebike walang kinalaman ang hall sensor po. Kung OK naman battery mo, check mo po yung fuse, breaker kung may breaker, mga terminal at socket baka may maluluwag lang kaya namamatay.
slmt po
Sir anung type po ng hall sensor ang ginamit nyu, unipolar or bipolar ? Salamat po sa reply
Gamit k ay hall sensor 413 Bipolar po yan sir
@@ricodaray may dis advantages po ba kung unipolar ang gagamitin?
sir i have one question every bldc motor have different hall effects sensor?
Bldc motors are different number but all are same
@@ricodaray thanks a lots sir , so i can able to any number of sensor which made for bldc motors ryt ?
And what u think about 60/120 this both going to work?
Sir baket may ganun sa throttle baliktadfrom 3.7 to 0.8ang bigay
Baka na baklas yung throttle tas mali yung pag balik
Very useful God bless
Thank you sir 😊😊
New friend PO.stay safe and God bless
salamat po
Thanku sir more videos
Thank you for watching sir🥰
Parepareho png b value ñg transistor po?anu pó value ng transistor nyan
Basta hall effect sensor same lang yan sila kahit magka iba number, gamit ko ngayun #413
@@ricodaray ty po
ano klase transistor yong sensor sir?
Hall effect sensor for BLDC motor po sir
ano pong hall sensor gamit nyo jan sir? ung 3144 po kahit anong ebike hub motor pwede un?
413 po gamit ko sa lahat ng ebike at etrike na ginagawa ko sir
sir bakit po wala na sa shooppe ng 413 hall sensor. ano po ang ang other name nyan sir or other code name? @@ricodaray
Hi sir...
What number of sensor can use for bldc motor hub 1000w 60v?
Mine is like citycoco chopper...
Help please...tq
Hello sir. I'm using hall sensor 413, and i use it to any kind of bldc motor for ebike
@@ricodaray owhhh...i will try...tqvm sir🙏
Boss meron b training center for ebike tech?
Di ko alam dyan sa manila kung meron na sir. Dati wala po
Ser nag rerewind po b kayo ng hub
Hindi po sir
Hello Sir . What's M warning light on e bike? Please tell me.
Hello sir. Some scooters display M warning, it means motor have problem. Some also display code error. But you can check to your manual to verify what error for M
about to do the same to a almost new ebike , BUT one of my hall sensors are turning - what i think - the wrong way ! the other directions of the 2 others . the one i got in the middle has the ....smallest surface turning against the axl if you know what i mean . have you ever seen that or do you as i - think that has always made the bike run strange !
You mean your motor only shaking, much better change a new hall sensor sir.
@@ricodaray IT was sitting right, i could se + and - was right to the sensor ....Strange BUT i dont get the 6volt signal so IT is bad. Thanks to guys like you i dont have to use All my familys money
@@ricodaray hey Rico...can you please give me a link to thoose hall sensors YOU use ...just replaced em, but now it gives me error code 3 " hall sensor " im not sure i got the right ....fuck
Sir I'm working in electric bike company so we have enough supply of parts. But here in Philippines we have LAZADA.com that we can order through online like this
s.lazada.com.ph/s.3Nqvj
@@ricodaray thanks...i got the store here in denmark , BUT is there a differnce in the sensors if its a 24 volt or a 36 or even higher ? i can get the hooneywell ss41 24 volt, but my battery is 36 volt, but that shouldnt be a problem you think ?
its ez to replace but have no idea which type of sensor should buy, in my case my middle hall sensor has the different model than left and right sensor ,
This my first time heard of different type of hall sensor inside the motor
Try this hall sensor link
s.lazada.com.ph/s.UoJ0M
@@ricodaray with this link there are many sensors with middle one different from side ones and also has to consider wattage of the motor and does the sensor can survive under high temperature or not,
Sir saan ang Shop mo ng EBIKE KZ KUNG PWEDE PO NA MAGPATURO SAYU NG ACTUAL MAGDALA AKO NG GAMIT
Di po ako nagtuturo sir
Anung klaseng transistor yan sir,?
Applicable po b yan sa lahat ng e bike.
Gamit ko hall sensor 413 sa lahat ng ebike. Pero kahit anong code basta hall effect sensor for bldc motor pwede kahit di pariho yung number
Thank sir
Question lang po sir nagpalit ako ng hall sensor okay naman voltage reading ng dalawa ( blue and green )5v pero yon isang yellow 3.90v lang okay lang po ba to? Or need ko palitan ulit yong hall sa yellow?
Hello po sir. Dapat same lang yung voltage kasi isa lang source nila galing sa controller. Baka sa wire lang may problima. Pero try mo paandarin kung gagana sir.
@@ricodaray gumagana naman sir ang problema lang mahina hatak nya. Palitan ko nalang siguro lahat ng hall sensor. Thank you po sa reply.
Hanep si kuya nagmemekaniko di man lang nagtanggal ng mga singsing- rich !!!!
Sir my access125 converted electric scooter 67v 800w hub motor
But recently hall sensor defective sir
N41 909 This hall sensor not available in market so any alternative is suitable
Give me replay sir thankq
Hello sir. I am using hall sensor 413 in all types of ebike i fix.
You can use any code as long as it is hall effect sensor for bldc motor.
@@ricodaray
Hello sir i have à citycoco bike,my contrôler is ok but my motor doesnt work ,What can i do,in thé first ans second etc thank you very much for your working ,
Dami binubutingting Ni daddy. 😁
Sir rico may size po ba yang hall sensor? Wala po kasing available sa store kung saan ko na purchase ang ebike. God bless po
Hello po, pag hall sensor po isang size lang yan pero magka iba ang number, pero same function lang sila
Try mo dito sa lazada sir
s.lazada.com.ph/s.dWabT
Meron din FB group maraming tech na ma kuha dun search mo lang Ebike Builders Philippines
Ask lang po ano po no ng transistor ng nwow ars po ty sa pag sagot po
Gamit ko po hall sensor 413
Hi. I see u have removed the little board and wired to transister. My question is do i need the little board to get power?
Hello sir. If the original has a board then you can use it again, but you can do also without board to run your hub motor
are hall sensor problems always noisy when it is not working? reason I ask is both motors cut out on my dual hub scooter. It happens when on hot day and full throttle. there is no strange noises or wierd sounds. All power is gone. this just happens when in dual mode, when just in single mode with rear wheel, I have no problem. Please help. thank you.
Hello, if noisy some problem is the controller, but mostly if noisy is because of hall sensors. Check also the hall sensors if install properly. Check also the alignment of magnet and hall sensor. If hall sensors far from the magnet also cause nof noisy.
@@ricodaray thank you!!! This is so helpful. but i forgot to say when typing my question that mine is not noisy. So what does no noisy tell you? what could that mean?
So logic says its probably not a hall sensor. But I'm confused about the controller. because when i see videos most people talk of controllers burning up and not working at all, all of a sudden and then broken and need to be repaired or replaced. I do not see any videos with my problem happening that i can find where it cuts off with no noise and then works again when i let throttle go back to nothing. I do not need to turn off the power or the key or do anything like that. but my problem is only on a hot day and when Im trying to do full throttle and then the motors cut off, with no noise, and no power. then if I bring the thumb throttle back all the way to 0 the motors work again if i am gentle. I can get 3/4 throttle and go 25mph (38kph) but i cannot make the full speed i otherwise used to make. about 33mph or 53kpph, but i cannot do that when it is hot outside or both motors shut off. If a battery overheated the bms shuts down then I think it would take time to cool off, but my scooter keeps going and take no time to reset by simply letting the throttle return all the way to 0 current. if I take easy on speed or if i only use rear motor on single drive setting there is no shut down and the scooter can get me home on dual drive. BUT if i try to go very fast in dual mode this problem will happen, only on hotter weather days. it is quiet with no strange abnormal noises.
How do i know if it is controller or problem with battery or bms? What does no noise mean? THANK YOU THANK YOU THANK YOU!!!!!!!!!!!
@@jesp999 im not sure but i think it is about battery, because if the battery power is not enough the bms will automatically cut off,
Rico may gb2 ako tailg un speed 2 n 3 same lang buo naman ang switch ko san kaya problem nito?salamat
Pag 1&2 gumagana peronpay 3 ayaw pumasok parang naka 2 lang, check mo yung speed selector switch baka sira na walang contact yung 3
Boss po sayo magpa wiring sa motor ng Foldy E-bike ko
Layo ka sir dito ako sa Davao
Hindi ba pasukan nang tobig yang motor sa haha?
Mas maganda kung may sealant ka lagyan mo nalang
Kahit nga yung dipa nabubuksan pinapasok parin ng tubig sir
boss tanong lng... ok lng bah nah 7k watts yung motor hub tapos 3k watts lng yung controller or need mas malaki yung wattage ng controller kaysa motor hub?
Hello po. Pwede naman po kasi naka depende sa controller yung ikot ng motor, kaso de maka perform ng sagad yung hub kasi hanggang 3kw lang yung bigay ng controller. At ang disadvantage is kung sino yung mababa ang power yun ang maunang masira. Mas maganda talaga pag pantay lang.
Rico Daray okay boss salamat nang marami..... more videos po lalo nat mga installation or upgrading ng ebike lalo nat sa mga tamang specs sa pag upgrade dami nyo pong matulungan po boss... God bless always boss...
6:15 hall sensor wiring configuration - thankyou
Orginal hall sensor -502f ?
I forgot the code
Boss san location mo..pagawa ko kc ebiko ko salamat
Hello sir. Dito ako now sa Davao😊
If needs mo ng tech ng ebike, mag join ka sa fb group Ebike builders Philippines , maka hanap ka ng malapit sa area mo sir
Mag kano po presyohan pag paayos master ng ganyan po? Pag Home service po
Hello po. 500 to 1k singil nila depende sa tech. Libre lang kasi pagawa nyan sa NWOW.
Sir Anong type Ng transistor sa hall sensor? Slmt po
Hello sir. 413 po yung hall sensor na gamit ko
saan po location p repair po ako ng ganyan
Davao city po ako sir
I have a 2800 watts hub motor and hall sensor name is 43f 026.....
But I cannot find it.......
Alternative sensor name please......
So hard to find same number but can replace it any hall sensor as long as for BLDC motor. Now I'm using 413 but i use it to any kind of ebike and strike here in Philippines.
Only 49e hall sensor available here........
Can i use this....?
@@muhammadishfaq5408 maybe can, but you can try if it will works