Thank God I found this because our belt is about shot and needs to be replaced. And I would have been the next guy to break the tensioner. God bless you for caring about others, I really appreciate it.
Thanks so much- You kept your word! Such a great tip Phil! I did notice the smooth pulley below when I changed alternator for nothing as the scraping noise hasn’t stopped. Noticed more pulleys grinding after turning by hand and not only belt tensioner pulley but also A/C pulley. A/C pulley seems complicated for the DIY’er- so that’s gonna cost quite a bit I imagine!
Yes you'll have to go ahead And replace The belt tensioner pulley And might want to go ahead and replace the belt too while you're at it, depending on how many miles it has. There are a couple of pretty good UA-cam videos on how to replace The bell tensioner
Yea, I stripped the bolt, however I couldn't get this method to work. Am I missing something? I'm trying to get it back on, and I stripped that bolt. Any help would be appreciated. Thank you.
Are we referring to the same bolt head that releases the tension off the belt? So if you stripped that you apparently were just pulling too hard on it or didn't have a proper fit for the bolt head(or both). If You haven't fixed it yet, try a 6 sided socket that fits it tighter. You don't need to pull on it that hard to slide the belt on. Note: There is a place when you're pulling on the bolt head that you hit a wall of greater resistance. This is the point where you do not want to pull harder, And shouldn't have to.
I removed it from the water pump area. It still broke. I was looking for a video to confirm I was removing the tension off the belt properly. It still broke. Now I'm out another 150$
sorry, but there should have been absolutely no reason to have needed to pull on it hard enough to break it, unless it was already cracked to start with
@@philhall7570 thanks for responding I got it replaced and wow not very fun! Now the check engine light is on and the car has a really low idle. Tomorrow I’ll pull the codes and go from there. Thanks my friend!
Thank God I found this because our belt is about shot and needs to be replaced. And I would have been the next guy to break the tensioner. God bless you for caring about others, I really appreciate it.
Hey man, I believe you! Never seen a belt so hard to put on👍 had to get my neighbor to come over n help!
And may you be blessed too, sir! Thank you for your generosity.
Thanks so much-
You kept your word! Such a great tip Phil! I did notice the smooth pulley below when I changed alternator for nothing as the scraping noise hasn’t stopped. Noticed more pulleys grinding after turning by hand and not only belt tensioner pulley but also A/C pulley. A/C pulley seems complicated for the DIY’er- so that’s gonna cost quite a bit I imagine!
Thanks for the heads up Phil! I'm replacing the alternator in my Camry and this tip really helped. Appreciate you man.
You men, you rock!!! 1 hour trying to put that thing in place until I watched this video and boom 2 minutes later job done
Oh man I wish i would’ve watched this video sooner because it was such a pain taking that belt off, thank you sir and god bless you
Great info…I learned the hard way…2 broke…you are absolutely correct!!!!
i feel your pain!
Thank you. I snapped that bolt BUT now i know how to install the new one easier and also NOT snap that bolt in the future.
thank you very much for that tip.I'm gonna do it tomorrow because the belt is ready to snaps!
I discovered this trick today and it is a life saver because it is much easier that trying to get inside those valley edges on the alternator
Great tip!!! Made the job a snap for me
Really appreciate this. God Bless
Thank you for the tip ..I am about to get busy on that....blessing brother...and amen Jesus is coming
Follow the good shepherd!!! Great way to end!!!
YOU ARE SPOT ON MY MAN !!!!!
Thanks make sense about to try it out
Thank you, just about ready to do mine and you are spot on!
thank you so much, this video made everything much easier ❤❤❤
If you have any questions on Rain Gutters(Eavestrough)or Glass/Windows I have experience with that if you need tips?
Thank you sir for those words of wisdom 😊😊😊😊
Thanks, I appreciate it!
I tend to agree. 👍
found my engine w/ this pulley bracket already broken, what is the solution now. Toyota Bracket Part Only ??
Yes you'll have to go ahead And replace The belt tensioner pulley And might want to go ahead and replace the belt too while you're at it, depending on how many miles it has. There are a couple of pretty good UA-cam videos on how to replace The bell tensioner
i like your style
going to try this tomorrow. gave up trying to get it back on the alternator pully
Amen Brother
Amen brother!!
Shout out to you sir
Thank you!
Thank you
Yea, I stripped the bolt, however I couldn't get this method to work. Am I missing something? I'm trying to get it back on, and I stripped that bolt. Any help would be appreciated. Thank you.
Are we referring to the same bolt head that releases the tension off the belt? So if you stripped that you apparently were just pulling too hard on it or didn't have a proper fit for the bolt head(or both). If You haven't fixed it yet, try a 6 sided socket that fits it tighter. You don't need to pull on it that hard to slide the belt on. Note: There is a place when you're pulling on the bolt head that you hit a wall of greater resistance. This is the point where you do not want to pull harder, And shouldn't have to.
This was a bitch to do. I would have been lost without the diagram.
Thank you sir
Thanks sir!
any chance you could share the torque settings for the two screws on the alternator?
I don't know that I've ever gone by torque settings when doing an alternator, But I did pull up 18' pounds on my phone
I removed it from the water pump area. It still broke. I was looking for a video to confirm I was removing the tension off the belt properly. It still broke. Now I'm out another 150$
sorry, but there should have been absolutely no reason to have needed to pull on it hard enough to break it, unless it was already cracked to start with
@@philhall7570 That piston that kept the tension was locked up. It's all good now. The new tensioner works perfectly. My problem has been solved.
What order pully when put the new belt?
doesn't matter as long as you put belt on water pump pulley last
What size motor?
4 cyl
Ok I am changing my belt and that bolt is snapped what do I have to do to get a new belt back on?
You have to replace the belt tensioner. I watched a couple videos online in Kind of combined Some steps
There might be a trick I don't know about To release the tension
@@philhall7570 thanks for responding I got it replaced and wow not very fun! Now the check engine light is on and the car has a really low idle. Tomorrow I’ll pull the codes and go from there. Thanks my friend!
@@katphishricky1832 the idle will reset after you drive it a few minutes