How to repair a floor jack that leaks fluid
Вставка
- Опубліковано 2 чер 2024
- This video will show you the most common way to repair a floor jack that is leaking fluid and thus won't lift. I am repairing a 3-ton floor jack, but most jacks are built similar. The O-ring location may be on the male or female side of the piston and the bleeding procedure should be in your owner's manual or you can do as shown in the video. Don't forget to put jack oil on the new o-ring and put some jack oil on the piston when you reinstall it.
NEW... on 10/2/2016 I filmed a new filling & bleeding procedure that worked even faster and got the jack back to 100%... • The final bleed - how ...
UPDATED VERSION HERE: • How to repair a floor ...
jack shown in video is Craftsman 875.501152
o-ring here: amzn.to/2iUhZHt
#wjhandydad #myfirstvideo #craftsmanjack
0:00 Sears Craftsman 875.501152 3 ton jack
0:23 leaking fluid
0:59 disassembly
1:43 unbolt handle socket
2:57 already tried the stop leak jack oil
3:23 remove the old o-ring
4:15 replacement o-ring size
4:56 new o-ring install make sure to put some jack oil on it
7:19 handle socket re-assembly - put some jack oil on the piston too
7:42 torsion spring
8:29 finger tighten the bolts
8:35 torque them down
9:19 jack is now working
9:53 THIS IS WRONG - please view this video for proper re-fill • The final bleed - how ...
www.WJHandyDad.com
Disclaimer:
Due to factors beyond the control of WJ Handy Dad, I cannot guarantee against improper use or unauthorized modifications of this information. WJ Handy Dad assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. WJ Handy Dad recommends safe practices when working on vehicles/homes and or with tools seen or implied in this video. Due to factors beyond the control of WJ Handy Dad, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not WJ Handy Dad.
As an Amazon Associate I earn from qualifying purchases - Авто та транспорт
Updated/revised version here: ua-cam.com/video/6M0Joi5CSmw/v-deo.html
I have an American made three ton floor jack that I've bought back in 1974. 4 years ago, my trusty floor jack died on me; there was no hydraulic pressure and it leaking badly. It sat in the garage ever since. I thought about buying a replacement from Harbor Freight Tools. I'm glad I didn't; instead, I bought the rubber o-ring and installed it on my old floor jack. Then I added some fresh jack oil. Bleeded the jack and it was good to go! For less than ten dollars and about two hours; it was well worth the time and effort. And above all, this video gave me the inspiration and motivation in repairing my floor jack. Old floor jacks never die; they will always keep on pumping. My hats off to you--WJ Handy Dad! You rock!!!!
glad you got it fixed... these old jacks are just too awesome to throw away
Here's a tip, when putting the piston back into the pump, don't just hammer or force it in, coat the shaft with oil and gently push down whilst twisting it left and right, this will allow the O-ring to find it's natural position and slide along the piston without shearing a piece out of the O-ring also make sure the groove in the top is pointing in the right direction that it came out. Don't take out the nut like shown here but remove the rubber or screwed plug in the top of the main jack section, this is where you add the oil and burp the jack after pumping it up all the way, lower it and repeat a few times this will remove the air from in front of the piston. When done, push the rubber plug across with a flat screwdriver a bit to let the air out, the oil should come about 10 mm from below the top of the hole when it's correctly filled.
Thanks for the easy fix. FYI, I found a faucet repair o-ring that fit perfectly at my local hardware store. Thanks for posting the dimensions, that was helpful. The one I found was for a water faucet, hope using it in hydraulic fluid won’t be a problem.
Hopefully it will work. I've replaced mine one time since I filmed the video but my jack still works great
I have a 2 ton jack that's 35 years old. O ring finally went out...Its amazing back in the day how well things were built.
Nice Video
Thx
I was getting ready to call a hydraulic repair location to get an estimate to fix mine. I decided to look on UA-cam to see if I could do it myself, I found your video repairing the exact same Jack I have. Easy fix, glad I watched your video, you even told me which O-ring to get. Thanks for doing the research for me.
Nice video. It's always amazing to me that most all products have one weak feature that causes a failure. Switches, access door hings, etc. Always good to know that most failures can be fixed.
Nice! As cheap as most stuff is made now days, I personally think it's always better to keep the old stuff working as long as possible.
ElationProductions I totally agree......and I used to have the same type of jack-i think I paid about 100.00 for mine about 20yrs ago@ Montgomery Wards....on sale@99.99-reg.price 149.98.- what an amazing jack. I used it on my old yachts (i.e. 1973 olds 98 & delta 88 royale convt.) It had the lifting power of three of those little trolly jacks,..!!!!
When the old stuff becomes totally dead, we might be better building from scratch rather than soft as butter steel that your can buy these days.
I have a jack identical to yours, pulled the seal, same thing as yours. called sterling and ordered my seal. The man on the phone said he has had a small run on these and customers said they got their info from a video on youtube. No doubt Your video. Thanks so much you are helping many people.
as many others have commented, make sure you put some jack oil on the o-ring before you install it
Thanks for the great video. I have the exact same jack. Couple of months ago it started leaking oil. Followed your video and it no longer leaks. I did have to use an O ring one size smaller. You just saved me about $60.
Well done Gary. I appreciate these videos you do and you have a way of making so many of these repairs easy looking. -Chris
I have this same jack. Purchased it 20 years ago at NAPA. Now I know what to do when mine breaks! Great video!
What brand of jack is that
I have an old Craftsman jack that looks just like this one. It's over 30 yrs. old and still going strong. Thanks for the video on repairing these, if mine dies, I will try and fix it like this first.
Don't get rid of it. If you can't fix it find someone who can. The new QUALITY jacks are expensive. Well woth it to get her fixed.
We collect the old Craftsman green 1 1/2 tons. (Collect may be the wrong word...Five jacks. Because we are lazy as the day is long so when jacking up a car ...well you see).
I have the same jack as the one you have, mine also has the casters all busted. Reading from some of you viewer's comments people have fixed them by purchasing a seal kit designed for these jacks; however, IMO spending $60+ for them is not worth it. I ended up buying a Daytona from my nearby Harbor Freight. I'm not a mechanic, I primarily would use it at home to do simple maintenance or repairs I can do with my limited skills. At the rate that I would be using it, odds are It will be the last jack I ever buy. I haven't gotten rid of it, I think I might give it a shot at repairing it by replacing the O-Ring you have listed, if it works great; otherwise I'll put behind the house for someone to sell it as a recycling material. Thank you for sharing the video.
I have a 3 ton Harbor Freight rapid pump jack at my shop and I keep this 3 ton Craftsman classic at my house. The HF stuff is definitely not as heavy duty but it gets the job done.
Definitely worth doing. I picked up a pair of matching heavy duty garage jacks from the sixties that were not working and in terrible condition. I was going to build one from the two,possibly the sellers idea too,but was not feasible. In the end they were stripped,blasted and painted and treated to new seals and bearings. For less than the cost of a crappy import piece of junk I have a pair of quality jacks that are great to use and look cool in my workshop. Now thinking about repeating exercise with an engine hoist and engine stand? Will look so good and be of top quality construction from a time when this mattered more than saving a few bucks on cheap shit!
I want to thank you so much for the O ring info. My Jack has been down for a few years and now thanks to you I can get it up and jacking again. Keep up the GREAT work. Mr Bobbo. B and B Auto Repair
Mr. Bobbo B. Really?? I will have to avoid your "Auto Repair" shop!!
@@clarencealexander1908 FYI That was 1 of 4 Jacks I own. It was more of a DYI project. And that's REALLY REAL!
Nice video. You did a great job explaining things in detail. Thanks.
I have a 2 tonne trolley jack sitting in the shed that stopped working years ago, yesterday I did what you did in the video and now it works like new , thanks 👍, I will show your video 📹 to all my friends 👍
Glad it worked well for you!
Thats a 3 ton Craftsman , I use mine as a professional . Never a problem in 26 years . Very very Heavy Jack as I pick it up daily . I am mobile so I strap it down just in case sudden stop ! Thank you for this post ..
I got mine in the mid 90's... admittedly it got some abuse as it was stored outside for a while and not used. Despite that just failed o-ring. These jacks are made like a tank!
thanks. mine is aluminum and I can no longer afford a new aluminum one. Had it at least 20 years. I'll remember this video to keep it in good working order.
Great video. Same thing was going on with my craftsman. Found a o ring at a local store that fit for 25cents!!! Good walkthrough and explanation. Saved me from spending a lot more $$$
un video de como harreglar u gato hidragulico de 3 toneladas en españal no levanta
Thank you sir. My jack had the exact same issue. Followed your lesson on both repair and oil service/bleed and she works like a good thing. Thanks again.
Glad it worked for you as well as it worked for me. Mine is still working like a brand new jack and it's been almost a year since I filmed that.
Thanks man for the very fast reply.
Nice one i bought one one of those jacks when i was 14 when i first started repairing my families cars, I'm now 43 and mine has never developed that fault but what i have developed is a wearing of the teeth on that release valve and they barely mesh together to close the valve so i just removed the valve and welded the teeth up and re-ground them and now works as it should.
that's real safe
Mark Mawson Sounds like you bought three(3) and have only one left.
I love this video content - its so usefull and helpfull.
Thanks for the informative video and explanation. I have exactly the same jack and it has been leaking in exactly the same place for a few years. Will no longer lift high enough to raise the side of my 'burb. I especially appreciate that you provided the exact size of the o-ring required - saved me a lot of trial and error. After your description, I was able to repair mine in about 15 minutes. Now it works perfectly. Apparently mine did not lose much fluid, because I never did see any bubbles during the purging process.
glad it worked well for you!
I love the sound of the rain on the background :D
These old jacks were built to last. I have an old Japanese made jack similar to yours, and it needs to be revived. I will get a repair kit on the internet and fully restore it, good paint etc this summer.
This is a fantastic video, I wish more UA-cam videos were like this. Straight to the point and taught me exactly what I needed. Doesn't hurt I have a very similar jack with the same issues. Still. Thank you.
make sure to put some jack oil on the o-ring before installing... that's missing from the video, and look for my 1 year update version to see the proper fill and bleed procedure to save yourself some time.
@@WJHandyDad thanks! Will do. Is there a quick way to tell if my jack is beyond fixing? My jack goes up but won't lift anything. How can I tell if the cylinder is done for?
@@jacklenton9884 that's beyond my skill level, but it sounds like a fluid issue. do the fill and bleed procedure and see if yours fixes. Mine was like that when I replaced the o-ring - it would go up but not lift anything. Then I did the fill and bleed procedure and to this day mine is still working great and it's a 20-something year old jack
Great video, i have an old fj i bought in 1987 at builders square and thank you for the video, im going to try and repair mine, its leaking bad, great job
Nice work. Thanks for the demo.
I always advocate repairing rather than simply buying a new product but often the weakest link prevents that (parts not available). Society needs to demand that products can be be serviced.
Right. Many of these old jacks require a complete rebuild; not just replacement of an o-ring. Rebuild kits can go way north of $100, and to pay someone to do it can result in costs of $150 or more. Most people will just order a replacement of equivalent or lower cost from Amazon, for example, or just go to Harbor Freight and buy a cheaply-made Chinese (lots of luck finding anything made in USA for less than $200) junk (3 ton jack for $100), not realizing that they're of dubious quality and safety. Virtually everything I've bought with the "Made in China" phrase is garbage; not made to last; enough to speculate that it's not simply the economics of cheap labor, but strategic. It's big-picture-view thinking that renders such an assessment, but makes perfect sense, and I doubt 1% among us has a clue or even a cares that the result isn't just loss of domestic manufacturing jobs; it's global reordering. If anyone reading this isn't aware of what the Chinese Communist Party (CCP) is doing in every continent with the profits made from peddling crap to the rest of the world, nothing I've said will make any sense. The CCP declared war on the U.S. years ago, but most among us have not a clue, given that they get all their "news" from media sources receiving large financial support from, among a long list of globalists, the CCP. Go figure. That said, your point is valid.
@@1973deepee Tried in vain to locate a simple rubber grommet for a bathroom fan. Three stores and an hour wasted. Covid to blame for out of stock stuff. Ridiculous!
Thank you for your video! The perfect fix for exactly my issue on my floor jack that looks exactly like this. $0.59 cent fix!
Thank you, I wasn't sure about the maintenance, or how to do it, but thanks to you're video I've got the knowledge now, have a great day, and God bless you. 👍
Henry👤💐💍🚗👫💄💋🍾💳🐶
このジャッキなおりましたか？
I've got the same jack with the same leak, just not near as bad. I was really hoping it was just an O-ring, so this video comes as a relief. I would, however, recommend using a jack oil that _does_ _not_ _contain_ _STOP LEAK_ ! 'Stop leak' is essentially synonymous with 'seal swelling'. That's possibly worth a try when the O-ring is old, worn out and chewed up from all the dirt and metallic abrasives floating around in the oil.
New O-rings are a different matter though: they don't have anywhere to go when they swell up, so they tend to get extruded out the sides, or they wear out prematurely from getting compressed against the moving component they're trying to seal around. Also, because it's expanding, the Buna is not only becoming less dense, but it's softening, making it easier for those abrasive elements present in the oil to damage it.
And while I'm ranting, the same goes for cars! If you're car isn't consuming oil, doesn't smoke or smell like burning oil, then don't use 'high mileage' motor oils. This term also indicates the presence of seal-swelling agents. If it ain't broke, don't 'fix' it! And have a great day!
Nice fix of your Craftsman jack. I would agree with screaming eagle not to use stop leak once you've changed the seal. I say this because I used stop leak in my power steering and while it did stop the leaking for a bit the seal eventually went and I had to put in a new ps rack and pinion. I did a video on replacing the rack and after I replace the rack I put in new fluid without the stop leak. Just an FYI.
Again nice job extending the life of your jack. Why buy new if fixing is cheaper.
BTW I came here from seeing you on WallysPlace66.
Welcome!
On my jack (same o ring seal set up) there is a thin plastic washer that sits underneath the o ring seal . It's hard to see when the o ring has been removed, but it's there. When fitting the fresh o ring, it's important that it's locates on top of the plastic washer . I put my old leaking o ring on the ram and held it up to the sky, I could see daylight through the damaged part of the o ring . . After I installed a fresh o ring seal (with a little grease) my oil leak was cured ! I also checked the ram for any sharp marks and cleaned it with very fine sandpaper (1000 grit) . This was a very easy repair . Note -: the first seal that is removed is only a dust seal and is not the o ring seal . The o ring seal and plastic washer sits aprox 20mm down the ram bore.
Hmm...when I took mine apart the o-ring was under the plastic washer.
This exact thing happened to me two days ago! Fluid right at that spot. This video came up by chance -what a coincidence. I won't have to "hope" topping it off with fluid will work anymore as I have already got a kit (Lazaar), have never installed it (because it is a SUPER b- job) and those aren't the problem seals anyway. Thanks for the video.
Yep. It works well now. It pumps up and holds. The new seal isn't even very tight, but the old one was very loose.
Just got a second hand floor jack for free. O ring has completely disintergrated. Now begins swing and miss. Wish me luck thanks for the video.
good luck but I bet you'll be fine
Great video,,,I have this same jack I bought used on Craig's List a few years ago, Didn't have any owners manuel so this helped me a lot...Thanks
make sure to watch "the final bleed" video too so you can get it working "like new"
Excellent Demo. Thanks
Hey that fixed my jack. Thanks!!
Good video. Sure helped educate me.
Ha. Thanks. I will make it if I have to. Thanks for doing the hard part. The o ring sizing is the hardest part. I ordered it already. Thanks again
This was great help, I was also able to repair my 30 year old jack that had sentimental value to me.
Thanks for the video......seems I have the same model jack with an identical leak........I just ordered the O-ring from Amazon..........thanks to you for posting the size........this will be my weekend project...........
oil up the o-ring when you install it and watch my updated version of this video for the proper fill and bleed procedure
I've already replaced my three ton jack that when I pumped it up it would work its way down . I topped it off and purged the bubbles out . Didn't help it any , I may later resort back to this video and replace the the o- rings if I can find the right size at that time . This jack of yours looks a lot like mine too - may be the brother too mine .Thanks for the video , I'm sure it will help a lot of people out there !
Make sure to watch "the Final Bleed" video too... it has some things that I learned after filming this video about filling and bleeding.
after its bled and it still does not lift you are most likely bypassing fluid through the main piston seal.if itstill doesn't lift after you replace the piston seal its in the safety.
Yup just did this to mine the backing plate is on top of the O ring. Definitely very tricky getting the new one back while making sure you keep the backing plate up also it seemed like the plunger went in pretty easily with not much resistance. What I did notice while taking it apart that I lost a lot of jack fluid when I pulled the plunger out and I had it in the release position as well like the videos I’ve watched. So I filled it back up got all the air out which was not much any how goes up and down nicely about 1 inch or more each pump so I guess I’m good there I think. Waiting to see how it does next time I use it. Thanks for the 2 videos. 👍👍👍
it amazes me how popular this video is and it must be that so many people have leaking/failing jacks
I have the same jack and problem right now..thanks. for the help....
Good video thanks for sharing .
Great info. Tried fixing my jack exactly like yours several years ago to no avail. I did notice though that I could have bled it alot better. Thanks.
check out the "final bleed" video to see how I refilled it and got it working like brand new
WJ Handy Dad
mmm.mm moo l
WJ Handy Dad 90000
Thanks for the video. For anybody who hasn't worked on these use common sense. Always use jack stands never use the jack by itself to hold the car up. After repairing lift a axel up. Put a jack stand in case it fails, but let the jack hold the weight for a reasonable amount of time. If it creeps down, back to the drawing board.
Outstanding video and presentation.
often people like to spay WD-40 on the moving parts, but it may be bad for the seals. I usually just put a very small dab of wheel bearing grease on the gear/sprocket. also a good idea to give it a few pumps before storage keeps a lil pressure on the seals they last longer. thumbs up the vid
Thank you for the help.
Have a 1 1/2 ton sears jack bout 35 years old and it's doing the same thing as your. pump about 20 times and it gets half way up but you can push it back down with your hand and fluid is coming out of the pump piston. Went to Amazon site for the "O" rings, thank for the link, just don't know what I am going to do with the other 24 rings. The jack was bought by my late father for me so I really hate the thought of giving it up. Thanks again.
remember to oil the o-ring before installing - that's missing from the video
@@WJHandyDad unless you need all of those "O" rings would you consider selling two of them plus postage for a couple of dollars.
email me dad@wjhandydad.com
I have the same model jack, just a different color (red). Bought it from Costco about 25 years ago, had the same leaking seal problem. Luckily had a seal in storage that fit, but I do remember the jack coming with an extra seal and plastic ring in the box the jack came in. I lost track of how many cars the jack picked up over the years, but these are good. They don't get the car up fast like the new ones, and they're not low-profile for dropped cars. But I'd like to see some of the new-fangled jacks go 25 years, change a seal, and go another 25 years....and maybe more.
I'm hoping mine will last the rest of my life and maybe even be able to pass it on to W or J when I die. They definitely don't "make 'em like they used to"
Thanks for your help brother very good video
Thanks for the great video. I found it by coincidence. I have the same model (may be a copied Chinese one) which leaks exactly on the same position. Now I know what I need to fix.
Thank you!
Glad it was helpful. Make sure you follow the "final bleed" video instructions for refilling. If I had this to do over again, I'd make one video... but I didn't know about the "filler plug" until later. Now my jack works as good as the day I bought it.
WJ Handy Dad brand name of jack is atlas?
mine is a Craftsman but who knows if it was made by someone else and branded as "Craftsman"
Dope this is a craftsman sold jack ? And to think I was going to throw it away 😅 thanks for the video. I have the same brand jack but in the 2-3/4 ton model. I’ll have to get my calipers out to measure the shaft diameter but as far as I can tell from eye balling my jack and your video the plunger looks to be the same thickness! I’m sure my dad will be real happy to know I fixed it and didn’t put it out on the street lol thanks for the repair tutorial brotha!!! 👊🏼 hopefully I get another 30 years of service out of this bad boy 😁
Btw: this is an awesome jack that has served my family for over 30 years and now that I found the parts to fix it I will be keeping it forever. but before I bothered with rebuilding mine I needed a replacement in the meantime and I purchased a new harbor freight Pittsburg brand 2 ton low profile jack. For the longest time I was having issues with the old jack and I’m really glad about the new purchase. I don’t like wAsting money and I’m also a firm believer in,”if it ain’t broke don’t fix it” however I must say I’m extremely happy I had a reason to go out and purchase an additional floor jack to now have two in the garage because of the facts, the new jack is much more easier to carry and transport since it’s half the weight! And it lifts a car up in half the time and also allows for much lowered cars to be lifted. So in a way I’m very happy the old jack gave me a reason to purchase a new much lighter much faster operating jack and I’m also stoked that I can keep the old girl still in service after a quick oring change 😁 if you got the money I wouldn’t even bother with the hassle lol these old ones are in no means a transportable friendly jack, it breaks your back literally going to try and pick this thing up…….just my $0.02
I plan on keeping my Craftsman "forever" but I also have a much lighter Harbor Freight jack too
Oh and thanks for putting it online for the rest of us.
this was my first video I ever made. Filmed with a Flip camera in one hand while we had a rare summer rainy day. And somehow it's my most popular video. LOL
great tutorial thank you very much
McMaster-Carr has the 208 O-ring , 100 pack $5.00
Good job, very patient, i would be cursing while i wrestle that o-ring 😂😅😅
one thing I love about YT is the comments - several folks have given helpful suggestions, including that I forgot to put jack oil on the o-ring and that I could have put the o-ring on the piston and let it seat itself. So if I ever have to do it again (so far it's still working great) I'll do a better job.
Thanks for showing it, to do for me.
Great video, I especially like the sticker on the socket for the size.. I've had sockets that the size is super hard to read ( Blackhawk)... Definitely need to put some on my own
I went from the first 47 years not needing glasses at all to needing readers once in a while to now needing readers for all close up work, and if it has to be really close I need a strong magnification. It's so weird because I used to have cyborg like vision, able to focus and read things far away or close up
Excelente
Nice job!!
Cool video 📹 bro 👍
man i got mine in the 80's so im hoping i can fix mine,ive seen on other videos if that metal piece is pitted it will still leak,but im going to try today.and give it a good clean,its filthy and then repaint it,hell it deserves it,ive used this thing on every vehicle ive owned haha its the huge orange one with a white bar,well whats left of it,mostly rusty now and spraying brake cleaner on it to clean it has stripped the paint,oh well better to try then spend close to 300.00 even though i do need one that can adapt a transmission holder thing haha,but ive made it this far with out one.thanks for your time
Got that same jack. Was my father in law’s and it didn’t work. Put some fluid in it, bled it out, and it’s working again. But it has the same leak at the pump shaft as this one, so I need to replace that O-ring too. Best tool for getting those things out of that groove is a pick with an angled tip....
good vid. mate cheers
Thank you for that, very helpful.
Very welcome, glad it helped. Make sure to watch The Final Bleed video for the proper fill and bleed technique
great video!
thank you. Make sure you watch "The Final Bleed" to see how I got it completely filled and bled.
Thanks for the video. I have an old Sears Craftsman model almost identical to yours that has the same problem. I think mine is about a 1984 model.
You may have the same jack as me. it's green in color model # 328.12002. Amazon has a complete rebuild kit for about $52.
I working on a neighbor Floor Jack that is similar to yours..painted up.
Do you have the model for that jack? I have the same jack but I do not know the model so I can order parts
I just subscribed to your channel and hello from New Hampshire usa.
Welcome to the channel.
Nice one
A lot of the older type jacks Sears sold were made by Norco a quality Japanese manufacturer. Norco has seal kits for EVERY jack they have ever made. Do a google search, you will find places to purchase a seal kit, parts for your jack.
Great video! is this a Lincoln jack? I have one exactly like it, and I'm trying to buy a repair kit but doesn't have any sticker on to know the model, thanks!
mine was a Craftsman from Sears but so many of them are apparently "clones"
This looks like one of the units I have to rebuild and I’ve decided to go at it the same way,,,I have plenty of stuff on hand and will go one at a time & should be able to come up with the parts I need from my own inventory.if not I’ll buy more but they’re only parts,I just need the right ones.
Great Video, the same thing that's leaking on my Jack too, Thanks for the Easy fix video.
I've replaced the o-ring one more time since this video was filmed. Other than that, jack still works flawlessly
@@WJHandyDad I went to Home Depot for an O ring, it wasn't exactly what the original one looked like but I put it in, and seems to be working now. It was: 1 in. X 3/4 in X 1/8 in thk. The plunger on my Jack measured a little less than 3/4 in in dia, but I gave it a try, and so far it's working. The old seal was more like a seal than an O ring, but I'll Google and see if I can find something close, just in case this O ring doesn't work. I don't know the make of my Jack, so it makes it a bit difficult in finding a replacement seal. Your video made the job Simple, and worked just like you said. Thanks again.
@@tipsclubs01 sometimes you have to fall back on "if it works, it works"
@@WJHandyDad You got that right.
I swear I had that same model.
I bought mine in 1996.
It came with two gray 3-ton Jack stands too.
I'm starting to wonder if that is what I got too because I have 2 gray 3-ton jack stands and probably got my jack between 1995 & 1996
I have the same setup as well. 3 ton jack & 2 stands purchased at Sears in 2002.
Very helpful
Seems like one of the contributing factors the the degradation of that top o-ring is the grime and pitting on the upper part of the plunger shaft. Might want to try to leave it stored in the downward position so the full length of the piston is immersed in the jack fluid.
Speaking of jack fluid. It might not be a good idea to have filled your jack with that stop leak oil. In most cases leaks occur when the seals get dried out, shrink and get brittle. The stop leak has seal softeners in it to soften and swell those hard seals. The problem is it also works to soften new seals as well.
By putting that much stop leak oil in your running the risk of softening the new seals to the point where they may break down.
Just something to consider.
Thank you... those are great tips. So far the jack has been working perfectly since the "final bleed" video was shot. Hopefully I won't have any problems down the road due to "too much" stop leak.
Screamin Eagle Subject: Asparagus DO NOT FAIL TO READ THIS AND SEND TO YOUR FAMILY &FRIENDS When I was in the USN, I was stationed in Key West, FL. I worked at the clinic at Naval Air Station on Big Coppitt Key just a few miles north of Key West. The hospital at Key West was for out- patients only, for retired armed forces personnel that lived in the area. If you needed to be hospitalized you were sent to Homestead AFB Florida. I had the day off and just went inside the hospital (Corpman barracks were next to hospital). There was a retired Navy man that worked in the lab and he was very interesting gentleman to talk with. He was a retired biochemist from the USN. He asked me what was going on that day, and I said I had the day off. I wish I was working, as the crew on, today was taking a sailor to Homestead as he had a very bad kidney infection. Now this elderly gent told me the man should have eaten more asparagus, and he wouldn't have that problem. I asked why? I'll never forget him saying, do you eat asparagus? and I said yes, I love them. He replied you notice how your urine stinks after eating asparagus? I said well I never thought it was what I ate but yes it does have a pungent odor. He said, It is because it is detoxifying your body of harmful chemicals!!! This was back in 1986 when I was stationed there and to read this email again I had to share this story...Eat more asparagus, my friends.
Asparagus -- Who knew?
My Mom had been taking the full-stalk canned style asparagus, pureed it and took 4 tablespoons in the morning and 4 tablespoons later in the day. She did this for over a month. She is on chemo pills for Stage 3 lung cancer in the pleural area and her cancer cell count went from 386 down to 125 as of this past week. Her oncologist said she will not need to see him for 3 months.
THE ARTICLE:
Several years ago I met a man seeking asparagus for a friend who had cancer. He gave me a copy of an article, entitled "Asparagus For Cancer" printed in the Cancer News Journal, December 1979. I will share it here, just as it was shared with me: I am a biochemist, and have specialized in the relation of diet to health for over 50 years. Several years ago, I learned of the discovery of Richard R. Vensal, D.D.S. that asparagus might cure cancer. Since then, I have worked with him on his project. We have accumulated a number of favorable case histories. Here are a few examples:
Case No. 1, A man with an almost hopeless case of Hodgkin's disease (cancer of the lymph glands) who was completely incapacitated. Within 1 year of starting the asparagus therapy, his doctors were unable to detect any signs of cancer, and he was back on a schedule of strenuous exercise
Case No. 2, A successful businessman, 68 years old, suffered from cancer of the bladder for 16 years. After years of medical treatments, including radiation without improvement, he began taking asparagus. Within 3 months, examinations revealed that his bladder tumor had disappeared and that his kidneys were normal.
Case No. 3, On March 5th 1971, a man who had lung cancer was put on the operating table where they found lung cancer so widely spread that it was inoperable. The surgeon sewed him up and declared his case hopeless. On April 5th he heard about the Asparagus therapy and immediately started taking it. By August, x-ray pictures revealed that all signs of the cancer had disappeared. He is now back at his regular business routine.
Case No. 4, A woman had been troubled for a number of years with skin cancer. She developed different skin cancers which were diagnosed by the acting specialist as advanced. Within 3 months after beginning asparagus therapy, the skin specialist said her skin looked fine with no more skin lesions. This woman reported that the asparagus therapy also cured her kidney disease, which had started in 1949. She had over 10 operations for kidney stones, and was receiving government disability payments for an inoperable, terminal, kidney condition. She attributes the cure of this kidney trouble entirely to the asparagus treatment.
I was not surprised at this result as `The elements of materia medica', edited in 1854 by a Professor at the University of Pennsylvania, stated that asparagus was used as a popular remedy for kidney stones. He even referred to experiments, in 1739, on the power of asparagus in dissolving stones. Note the dates! ---We would have other case histories but the medical establishment has interfered with our obtaining some of the records. I am therefore appealing to readers to spread this good news and help us to gather a large number of case histories that will overwhelm the medical skeptics about this unbelievably simple and natural remedy.
For the treatment, asparagus should be cooked before using. Fresh or canned asparagus can be used. I have corresponded with the two leading canners of asparagus, Giant and Stokely, and I am satisfied that these brands contain no pesticides or preservatives. Place the cooked asparagus in a blender and liquefy to make a puree. Store in the refrigerator. Give the patient 4 full tablespoons twice daily, morning and evening. Patients usually show some improvement in 2-4 weeks. It can be diluted with water and used as a cold or hot drink. This suggested dosage is based on present experience, but certainly larger amounts can do no harm and may be needed in some cases.
As a biochemist I am convinced of the old saying that `what cures can prevent.' Based on this theory, my wife and I have been using asparagus puree as a beverage with our meals. We take 2 tablespoons diluted in water to suit our taste with breakfast and with dinner. I take mine hot and my wife prefers hers cold. For years we have made it a practice to have blood surveys taken as part of our regular checkups. The last blood survey, taken by a medical doctor who specializes in the nutritional approach to health, showed substantial improvements in all categories over the last one, and we can attribute these improvements to nothing but the asparagus drink. As a biochemist, I have made an extensive study of all aspects of cancer, and all of the proposed cures. As a result, I am convinced that asparagus fits in better with the latest theories about cancer. I was given these facts by a good friend but as with anything do your own research and make your own judgements thank you Dave Wright. Here are my thoughts on the material. Asparagus contains a good supply of protein called histones, which are believed to be active in controlling cell growth. For that reason, I believe asparagus can be said to contain a substance that I call cell growth normalizer. That accounts for its action on cancer and in acting as a general body tonic. In any event, regardless of theory, asparagus used as we suggest, is a harmless substance. The FDA cannot prevent you from using it and it may do you much good. It has been reported by the US National Cancer Institute, that asparagus is the highest tested food containing glutathione, which is considered one of the body's most potent anticarcinogens and antioxidants.
Just a side note... In case you are wondering why this has not been made public, there is no profit in curing cancer.
Please send this article to everyone in your Address Book. The most unselfish act one can ever do is paying forward all the kindness one has received.
Great video. I have the same Craftsman jack, and I was wondering if you know what the maximum lift height is. My jack is working but the max lift height seems way too low (although I forgot to measure just how low). If a jack doesn't lift to it design height, does that most likely mean that it's leaked out some quantity of hydraulic fluid? Thanks for sharing your fix.
Fix it?
Use jack oil to lubricate the o-ring before assembly. It will go together easier
Great video! I see these o-rings come in a few different hardness types 70,75 & 90 durometer. Would the 70 work being softer in my jack?
honestly I don't know, I guess you could try them and see and let us know.
Well I ended up using the 70 durometer o-ring and all is good so far. My jack is back in working order and I thank you for your video 😉
glad it worked out for you!
Hola saludos desde México
Had a large old Sears Craftsman floor jack not holding pressure. Used to be able to get seal kits very easy, copper washers, check ball and spring, o-rings. but many years ago they were discontinued and seals no longer available. So much for good old quality tools can't get parts for.
O rings conform to a standard, as with bearing balls, you virtually never need to go to the original supplier (they always charge a lot more)
Instead, go to a seal supplier who stocks a complete range, and get them to supply seals which fit.
Any neighbourhood machine shop can make up copper washers from an offcut of copper bar.
Nice detailed video.How did you choose the o ring hence not knowing the jack manufacturer
Nice video
Thank you
Just to let everyone know. If you use hyd oil in your jack you have to be carfull what type of o ring you use. If you use trans oil it doesn't matter the materials the o ring is made of. We have tried an experiment and put hyd fluid in a car break system to show the differences in rubber for a class. It works for a bit but the hyd oil swells the rubber (orings) I believe viton is the right type for hyd oil system. We did this for a class to show the difference in typs of rubber and the uses. The wrong material o ring will work but not for very long though.
Thanks, this helped me with my Harbor Freight 3 ton piston seals. I ordered a kit from Lazarr's, it comes with a flat rubber "back up" ring that replaces the plastic retainer.
I still have the manual to that 3 ton jack. And I am gonna try and uoload the pages in a jpeg and link it here if Googles/UA-cam will let me.
Find out how?
Thanks for the video 👏👍💪👉
I am a hydraulic jack technician.
It is only due to insufficient oil, suction valve defect is occurring.
Add a specified amount of oil and remove the air, it will fix it.
Unnecessary things, do not disassemble.
Chevy trailblazer power brake
I want to know how to remove air
Thank you so much.
You're welcome. Make sure you watch the final bleed video to get it properly refilled and bled.
Great job in Shed due to covid always said must fix that start tomorrow..wellsine from Ireland
hope you get well soon (or stay safe, couldn't tell if you were saying you have it or not). Either way, hope you get your jack fixed.
How has this o-ring repair holding out in the long term? I replaced the piston seal once in a smaller jack and I noticed that the original seal was more like a D-ring and I inserted the same size O-ring. It performed for a while then started leaking again. What happened was that the the replacement O-ring tended to roll-over on itself inside the channel and therefore wore out prematurely.
I replaced it one time since. But the jack is still working great.