I really want to thank you. You set me in the right direction with my issue I've been trying to figure out with a brand new trans. Working with a LS swap GBody with a 4l65e , car randomly started having issues shifting so I did the whole multiple solenoid change and still no fix. Thought it might be the brake switch, nope. So now at this point I'm ready to switch to the 4l80 just wasn't ready. Got on the TUBE did a lot of research, cane across this vid and was like it CAN'T be that easy no way so I didn't pull them immediately. Ended up pulling them right before work just for kicks and not one was blown. "I knew it couldn't be that easy" I said to myself, cold stared the beast, warmed her up and proceeded to work. Pulling out of my neighborhood and felt it KICK into 2nd, "WAIT WHAT" get down to the stoplight and felt it downshift "WAIT WHAT". Finally get to the highway and felt the first 3 gears change, thought aw man no lock-up 😔...... get to cruising speed and clunk goes up shift to 4th. Boy was I ecstatic, I mean so much so I had to write this comment. Side note none of my fuses were blown after I pulled them 1 by 1 on my painless performance ls swap fuse box. THANKS AGAIN..... AND REMEMBER CHECK YOUR FUSES.
Man, I want to thank you for posting this video. I just spent over 500$ in parts and labor to change all the solenoids(didn't want the other ones to fail a week later when it's so hard to get to) and nothing happened. This mechanic I had work on it, ase certified mind you (should have his certification pulled) never checked something as simple as the fuses. Just dived elbows deep in the tranny cause he knew that's where the labor cost would come in. I watched this video this morning, and decided to try it. 1 15a fuse, this entire time. So again, thank you.
Oh my gosh!!!! I was ready to do all that work until I ran across your video... I am going to check my fuses 1st for now on when the (cel)check engine light comes on. Thanks so much for the info. 👍Common sense says you always check the fuses first but we always think the worse when things happen. 😁 You're the best, guy!
Gotta love Chevrolet fifdeen hunrentbuk and he got a 2006 4 door 4x4 blacked and chrome pickup truck due to there being a bad fuse. BEST RESALE VALUE ON THE MARKET
People this guy is correct, look for the trans solenoid fuse and replace with the correct number before doing anything else. Even if the fuse is not blown replace with new.
I agree on changing the fuse even if it's not blown. I had a situation where my cigarette/USB connection inside the truck was not working. I tested the fuse several times and it always tested good. I gave up on it for several years. It wasn't until a coworker told me to just swap out the fuse with a brand new one. It finally worked with a brand new fuse.
My 2004 gmc Yukon xl was having hard shifts from 1 to second and the rest would shift smooth. Changed the btsi fuse 10amp and test drove it did a few test and it seems to fixed the problem .
This saved me this weekend on my 08. T-case actuator toasted, but in the process took out the Trans-Ign Fuse with it as collateral damage. Trans went into limp mode and I only had 3rd gear and reverse. New fuse and transfer case actuator ($175) dollars later, everything was back to normal. I initially thought solenoids or worse too.
Did you have 1st 2nd and 3rd gear but no reverse? I have 1st skips 2nd and goes directly to 3rd after a few minutes and no reverse? What could that be?
Have a 2004 Silverado 1500. Would not go into reverse, but all other gears worked. Noticed that the radio was not working either. After taking out the radio fuse and re-seating it, the radio works and reverse works as well. Wouldn't have though that would have fixed it, but it did.
Thank you for saying check your fuses I was just about to pay $3000 and I went outside and I checked my fuses and it was a fuse so I just wanted to say thank you very much for this video
Just bought a 2007 Silverado 3500 with 165k KMs with a 4l80e and it was showing p2761, p0758 and p0753 codes. Had a look at the fuses and the btsi fuse was OK but it turned out the Ign0 fuse was missing. Put the fuse in and cleared the codes and the truck is out of limp mode and shifts perfectly.
I put three injectors from a scrap yard in my 1986 cavalier because it has a blown ecm fuse. Car sat for 18 months. Lesson learned. Fuse panel is my first stop.
BTSI 10 amps. Check connector at the transmission too. 4L80Es are tough, so less likely the 2 solenoids. You may have to wiggle all fuses, unplug and plug all connectors, check the 4 or 5 super important negative grounds, battery to body, battery to frame.
What is the 4 & 5. You said to check the 4 & 5. My son worked 2 jobs, saved up & bought a used 04 Chev Silverado for 7k. (4L80-E) Less than a month later transmission is slipping. P0894 code. Fuse is good.
@@larsclem well that’s just the trans cuz if it’s slipping it means it a bad trans the video was saying if it’s not shifting any gears then check the fuse hope this helps
@@vetcz8825 Thanks. Turns out that the transmission cooling line was leaking fluid into the transmission. What's crazy is the bottom of the transmission looked fine, but the internals were trashed. We had to have the transmission completely rebuilt. Thanks again.
I got my van for 500. no first gear and i dont think it shifts past 3rd. I am going check this right now LOL. you may have saved me a lot of effort. . will update either way.
if pulling all codes 1-2 &2-3&torque solenoid and not fuses try disconnecting battery clamp positive and negative together for 15 minutes with key out of ignition. then reconnect battery, turn key over but not start 3 times Holding for 5 seconds start vehicle let run for 5 minutes so it learns ideal idle, moke sure everything is off before doing, then hold brake move shifter into every gear 5 seconds each then each one again back to park 5 seconds each. drive approximately 4 miles normal and it should shift perfectly. all this works if when you crank it over the check engine light goes off if check engine light is still on then you need to find where a wire isn't ground
I have a 05 chevy suburban was driving had acted like it went into neutral coasted to side of road lost all gears would not pull i checked shift cable good it moves no vlown fuses transmissionjust doesnt engage????
I'm going to give your advice a try and check into the fuses I have a 05 yukon and the Trans was rebuilt at amco before I bought the truck Trans doesn't have 100000 on it yet I was driving the other day and noticed I didn't have 4th gear 123 and reverse work great smooth as can be no cel codes or Trans codes I did put a engine in that I put a stage 2 cam on but it's tuned at 276hp so it dosent damage the transmission
Great, doing troubleshooting/testing on the fuses first, but you have to look deeper...what is the actual 'cause' of a fuse blowing? My blown fuses always had an overload somewhere, so fix that too, or you'll be replacing fuses by the dozen. Thank you
Omg!! I spent all day changing the cylonids on my s10. Still no third or forth gear. I will check the dudes first thing in the morning!! Fingers crossed
OMG I Have a 1995 Sonoma we rebuilt it started up-cherry sounded better than before went a few miles then we couldn't shift to any gear. I really like this truck but aaaarg! It's driving me crazy
If anyone can help I have a 2004 z71 Silverado after someone installed my stereo drive goes into limp mode but reverse works great and the transmission was perfect before radio install
The owner that I had the truck before me the transmission went out on him had no reverse at all. So I bought the truck for $300 and spent $400 on a 4L60e with 200k miles drove it around town and when I took it 50 miles from my home town it said trans hot. Idle eng. Let it cool down and drove it back home. Truck only got 1st and 3rd gear no 2nd or reverse. Could it be the fuse?
Hello, my old automatic transmission moved on only one gear (like a reverse gear). I changed it, but the new one is same thing. I've tried new brain box, I've scanned the car, it shows no problem. I've had an electrician check the car and he said the fuse is good. Is it possible that the fuses are good but not receiving enough current or have some other issue?
You not a Dumb ass. YOUR A SAINT!!! Bruther bye posting this video you will have saved many hard working people THOUSANDS OF DOLLARS !!! GOOD KARMA IS COMING YOUR WAY ! Hundreds of rip off artists are now screwed because of this video. UA-cam has been a God send to the average working person that can't afford to get screwed over. Thank you from the bottom of my heart ! Bless You 🙏
Mine died on me while driving down the highway and wouldn't start and the shifter got stuck in second gear it would start out in drive but some down to second, what would cause that ?
I have a 99 tahoe seemed to work fine except it didnt feel like I ever had a passing gear in it put the gas all the way to the floor and it never kicked down . Also had a code for the A solinoid replaced It and the code stayed . Now the only way to get it to move is to run high fluid level and let it warm up. Any ideas? Aside from redoing the solinoid again will check fuses bit now that the fluid level is where it's supposed to be it wont move at all .
I'm having the same problem with my 2003 Yukon Denali shifts perfectly 1-2 then when I'm driving 30mph doesn't shift to the 3rd one 🤔 I shall try the fuses Nd I'll will update so hopefully that's the problem
if no third it's probably the clutch patch burned out. If you have ONLY third then the transmission is in standby safe mode or whatever limp mode - and so probably electrical.
Damn my engine light just came on with the code p0740 . But my truck runs really good and shifts pretty smooth no problems whatsoever. Why would that light come on?
i have a '03 Chevy Z-71 4x4 extended cab i just replaced the 4L60E tranny with a rebuilt . i put on 825 miles on it since , running fine up until now. i was cruising down the freeway just fine and all of a sudden it just went out. pulled off the freeway and checked the fluid and it was fine. started to take off again and it was slipping real bad ... any ideas ?
Mi 2000 chevy 4 wheel drive won't go an any gears. before I buy a new automatic transmission, is there any easy fixes like a bad furs or disconnected wires
I am having problems with Our 2007 chevy suburban. We had a chevy place hook it up and said 02 sensors bad on drivers side changed both and sparp plug wires, engine idles, but when put in gear it stalls, wont shift and speedo not working.
Could be your throttle positioning sensor. There are two sensor/valve on the drivers side of the throttle body they are cheap and easy to change EGR valve and TPS sensor. Also clean your throttle body the 07 has electronic throttle so don't get your fingers cut off. Is the motor stalling or the transmission or both could be the brain or bad/burned wiring. I had an 03 that would idle faster and faster got dangerous, changed TPS/EGR next to it nothing helped. We plugged it to a computer and didn't read a problem. It ended up needing a new brain. I sold it as is and i still see it running around it had 265,000 when i sold it 3 years ago.
I need to give this a try i changed everything i possibly could in the pan and the speed sensor mine shifts perfectly but then not 3 or overdrive usually not that lucky but I'll give it a try thanks
I am having a similar problem I have a 99 Oldsmobile Alero 2.4 I changed all my solenoids and tfp switch and still my car won't go into gear I checked the transmission fuse it seemed to be fine I am at a lost can you possibly help me
Check if the VSS Vehicle Speed Sensor is bad, its a sensor on the outside of the tranny that registers speed & the engine computer knows when to shift gears. If its bad the speedometer will be erratic or does not work and the odometer may or may not work plus a bad vss will cause erratic shifts and it won;t shift into higher gears or overdrive. If the vss is good then you may need a partial or full rebuild, depends on all symptoms. Use google to find images of the vss location if you don't have a shop manual. Or search online forums for pictures. Good luck!
Omg I have a 1996 Chevy 1500 and it won’t shift into 3rd and this guy tells me I have no fluid in it .. he doesn’t know where it’s going .. so I need a new transmission more than likely $2000 bucks ., Ok so it’s been sitting since December 2018. Then my friend Phil has the same kind of truck. But I have a computer for my transmission.?????Something his doesn’t have. And things are disconnected.. hum wonder how that happened, and I have plenty of fluid.. so it could be a fuse?? I love it.. thank you so much...
I have a 2000 gmc 3500 and trans is stuck in 2nd gear and converter is locked worked fine till had to replace ignition ass. In steering column now starts and runs great no shift any ideas
Is linkage cable all properly reconnected and not broken I.E. will the shifter move but the truck just stays in 2nd or will the shifter not move and is stuck in second. Really sounds like something didn't get put back together right if it was working fine before. You may have unhooked your shifting cable on accident.
was the ignition switch you put in it new, and non chinese made. I know in the 96, 97 era trucks would get stuck in a gear when it needed a new ignition switch. It may be a bad ignition switch not sending power back down to the transmission. I would bet that is your trouble.
Rob Netherland mine does the same thing. its so frustrating. operates fine when its cold but when it warms up after a few miles it has no 3rd gear and up. stays in 2nd. feels like limp mode but the display isnt reading any code.
I have a 2003 Chevy Trailblazer, I have to shift it into reverse 2 or 3 times for my truck to actually move in reverse. Could this be a fuse issue or does it sound like something else?
I certainly have the fuses checked 1st, thank you 😊 yeah I read it could be a solenoid issue as well so I’m glad you second that suggestion that for me, thanks again
My 2001 suburban started to slip i believe , it shifts good 1st and 2nd then going into 3rd the gear doesnt go in and it idles really high, i have to release the pedal then push it fast so 3rd goes in ? Any ideas
I have a question my truck has the full power but dosen't shift to 3rd when I'm driving 1st and 2nd go in fine then the transmission downshifts to 1st and stays there what could it be if it's the solenoid which one could it be?
Hey guys. 4l60e wont shift out into overdrive. Did shift out before fine. Speed sensor went out replaced it. Now wont shift out into overdrive.???????? Help please
I have a Colorado that transmission work fine for about 1/2 mile then it is like it went to neutral. I can shut it off and restart then does same thing again.
Pump or Sun shell if it goes into reverse then the pump rotor broke, the sun gear runs 2,3,R If the pump rotor is completely bad you will not have reverse or drive. But I have seen them where the rotor is cracked in half so it works at low rpms then when you Rev them up they don't work at all
I have tahoe 2005 i change transmission oil and fillter . suddenly transmission works only in 3 hard and heavy stat drive it our workshops not pro they told me we must replace every thing inside transmission . including clutch i need help for that issue coz very expensive to do what they said to me
Mohamed Fathy Someone fix my car i asked him to chick fuses an selonoid later he call me to take my car after he fix it . but unfurtunitlly he was very busy to let me know what he did to fix ghe problem any way . I'll see what he did then I'll be back to you.
need help please, chekd all fuses nd changed all 4 silinoids and still my truk is not shifting gears and my tac is not working. please any idea what that mayb?
the service engine soon light came on, then the tach and speed ometer quit worrking.it's hard to get the shifter out of parkwe changed all the solenoids filter and fluid the truckwon't shift by itself. manuely no 3rd or overdrive it has reverse. thanks mikie.
Christopher Williams7 months ago the fuse he changed is called the BTSI( Brake Transmission Shift Interlock) fuel it should be next to the ac relay . Its a 10 amp red mini fuse. Reply 9
I changed a bunch out when I was replacing them and I didn't mark them but it was for sure on of those 5 I point at towards the end of the video sorry couldn't be more helpful
Not a bad truck for $1,500 bucks..... When that transmission craps out get a BULLRIPPER transmission. I have one in my 2004 Chevy Trailblazer EXT LS 5.3L it's a beast on the road.....
@@landrun89 hope too good this is my problem! 1st second work when put in 3 or d it revs/misses I drove two hundred miles in second and no issues except for seems a little harder shifting!
My 1999 merc mountaineer tranny was slipping in drive, added some fluid and started to run good and no slipping. Then vehicle made a hard kick bang sound and the vehicle wouldn't go forward anymore. Drove it 3 miles in reverse to house. Any info on what I need to look for. Thanks peeps 🙋
Look underneath by the passenger side front tire for the wire that goes to one of those solenoids make sure it didnt come lose my s10 did the same thing
I have a 93 Chevy 4x4 350 4l60e and it will shift from 1 to 2nd but not into 3rd or 4th it was shifting fine then just felt like it would go into neutral but when slowed down it would grab 2nd again. any ideas? thanks. my buddy says it's the vss? I have already changed the 2 sensors on tcase with no change. thanls
Brian Baker that is what mine did and it was just a fuse, could also be 3-4 solonoid. it was a 10 amp fuse that I point at towards the end of the video.
thanks for the reply when I go to my buddys house this weekend I'll make sure to check fuse and replace the solenoid. really hoping it's not the actual trans. I just bought the truck for 2500.
I really want to thank you. You set me in the right direction with my issue I've been trying to figure out with a brand new trans. Working with a LS swap GBody with a 4l65e , car randomly started having issues shifting so I did the whole multiple solenoid change and still no fix. Thought it might be the brake switch, nope. So now at this point I'm ready to switch to the 4l80 just wasn't ready. Got on the TUBE did a lot of research, cane across this vid and was like it CAN'T be that easy no way so I didn't pull them immediately. Ended up pulling them right before work just for kicks and not one was blown. "I knew it couldn't be that easy" I said to myself, cold stared the beast, warmed her up and proceeded to work. Pulling out of my neighborhood and felt it KICK into 2nd, "WAIT WHAT" get down to the stoplight and felt it downshift "WAIT WHAT". Finally get to the highway and felt the first 3 gears change, thought aw man no lock-up 😔...... get to cruising speed and clunk goes up shift to 4th. Boy was I ecstatic, I mean so much so I had to write this comment. Side note none of my fuses were blown after I pulled them 1 by 1 on my painless performance ls swap fuse box. THANKS AGAIN..... AND REMEMBER CHECK YOUR FUSES.
Which fuse is the fuse on relay for trans ? With the standalone ??
Look on the underside of the cover for a fuse diagram, the transmission control module fuse is abbreviated TCMB or TCM-Batt.
Those are not listed in the fuse box. What car are you talking about? Lol
Nnbs
Man, I want to thank you for posting this video. I just spent over 500$ in parts and labor to change all the solenoids(didn't want the other ones to fail a week later when it's so hard to get to) and nothing happened. This mechanic I had work on it, ase certified mind you (should have his certification pulled) never checked something as simple as the fuses. Just dived elbows deep in the tranny cause he knew that's where the labor cost would come in. I watched this video this morning, and decided to try it. 1 15a fuse, this entire time. So again, thank you.
Glad it helped you! Thanks for watching
seriously what fuse are y’all replacing?
@@natesnathan1 I’m wondering the same thing
What fuse did you replace
Which one? All mine looked good.
Oh my gosh!!!! I was ready to do all that work until I ran across your video... I am going to check my fuses 1st for now on when the (cel)check engine light comes on. Thanks so much for the info. 👍Common sense says you always check the fuses first but we always think the worse when things happen. 😁 You're the best, guy!
Gotta love Chevrolet fifdeen hunrentbuk and he got a 2006 4 door 4x4 blacked and chrome pickup truck due to there being a bad fuse.
BEST RESALE VALUE ON THE MARKET
People this guy is correct, look for the trans solenoid fuse and replace with the correct number before doing anything else. Even if the fuse is not blown replace with new.
That makes absolutely no sense lol why replace a fuse that is not causing excessive resistance lol
I agree on changing the fuse even if it's not blown. I had a situation where my cigarette/USB connection inside the truck was not working. I tested the fuse several times and it always tested good. I gave up on it for several years. It wasn't until a coworker told me to just swap out the fuse with a brand new one. It finally worked with a brand new fuse.
There is no fuse that says for transmission. Can you get closer look at fuse box
@@chrisgarcia4653 Another video i just watched said the fuse said TCMB that is for transmission control module don't know about the B
My 2004 gmc Yukon xl was having hard shifts from 1 to second and the rest would shift smooth. Changed the btsi fuse 10amp and test drove it did a few test and it seems to fixed the problem .
Glad you got it fixed!!
landrun89 thank you very much for the help
I have a tahoe 2003 and it doing same problem
This saved me this weekend on my 08. T-case actuator toasted, but in the process took out the Trans-Ign Fuse with it as collateral damage. Trans went into limp mode and I only had 3rd gear and reverse. New fuse and transfer case actuator ($175) dollars later, everything was back to normal. I initially thought solenoids or worse too.
Awesome.. saved me alot of heartache!! Thought my trans was messed up!!
What fuse?
Brake Transmission Shift Interlock love this saved us 1000.
Classic Auto Body what’s that and where is it
Classic Auto Body u
Wow what were your symptoms before
been there, done that.. thanks for the reminder. Glad your truck is fixed!
Did you have 1st 2nd and 3rd gear but no reverse? I have 1st skips 2nd and goes directly to 3rd after a few minutes and no reverse? What could that be?
Djcatfishing same
Have a 2004 Silverado 1500. Would not go into reverse, but all other gears worked. Noticed that the radio was not working either. After taking out the radio fuse and re-seating it, the radio works and reverse works as well. Wouldn't have though that would have fixed it, but it did.
Thank you for saying check your fuses I was just about to pay $3000 and I went outside and I checked my fuses and it was a fuse so I just wanted to say thank you very much for this video
What were your symptoms before
What fuse?
@@airborne_12vdid u ever find out what fuse ?
Just bought a 2007 Silverado 3500 with 165k KMs with a 4l80e and it was
showing p2761, p0758 and p0753 codes. Had a look at the fuses and the btsi fuse was OK but it turned out the Ign0 fuse was missing. Put the fuse in and cleared the
codes and the truck is out of limp mode and shifts perfectly.
Everyones talking about this IGN O fuse, but I can't find one nor a an empty slot for one. Got IGN A, IGN B etc.
@@treslongwell5066same here
Under the hood?
Smartest video I seen in awhile. I forget too often to initially go to the fuse box for answers.
Thanks for the heads up. I hope the guy who sold u this truck doesn't see this vid..lol it was only a fuse..wow
I put three injectors from a scrap yard in my 1986 cavalier because it has a blown ecm fuse. Car sat for 18 months.
Lesson learned. Fuse panel is my first stop.
Fuckin Wat.
media.tenor.com/images/2f9b0e2be3b636771cdc5d0b978d0978/tenor.gif
Start small them always go up... Thanks brother for the video
BTSI 10 amps. Check connector at the transmission too. 4L80Es are tough, so less likely the 2 solenoids. You may have to wiggle all fuses, unplug and plug all connectors, check the 4 or 5 super important negative grounds, battery to body, battery to frame.
What is the 4 & 5. You said to check the 4 & 5. My son worked 2 jobs, saved up & bought a used 04 Chev Silverado for 7k. (4L80-E)
Less than a month later transmission is slipping. P0894 code. Fuse is good.
@@larsclem well that’s just the trans cuz if it’s slipping it means it a bad trans the video was saying if it’s not shifting any gears then check the fuse hope this helps
@@vetcz8825 Thanks. Turns out that the transmission cooling line was leaking fluid into the transmission. What's crazy is the bottom of the transmission looked fine, but the internals were trashed. We had to have the transmission completely rebuilt. Thanks again.
You got a great deal on that truck!
Justin G starter relay
starter relay on a 2003 Silverado
starter relay on a 2002 Silverado
Justin G
I got my van for 500. no first gear and i dont think it shifts past 3rd. I am going check this right now LOL. you may have saved me a lot of effort. . will update either way.
Kip's Journey Did it helps?
3 years later... not 1 update
5 years later still no reply…see what happened was he went to go check on it that very minute & passed away from electrocution DAMN FUSES lol jk.
What kind of problems where you having something específic will help more. Thanks for sharing
if pulling all codes 1-2 &2-3&torque solenoid and not fuses try disconnecting battery clamp positive and negative together for 15 minutes with key out of ignition. then reconnect battery, turn key over but not start 3 times Holding for 5 seconds start vehicle let run for 5 minutes so it learns ideal idle, moke sure everything is off before doing, then hold brake move shifter into every gear 5 seconds each then each one again back to park 5 seconds each. drive approximately 4 miles normal and it should shift perfectly. all this works if when you crank it over the check engine light goes off if check engine light is still on then you need to find where a wire isn't ground
Totally tubular dude,Hope mine is that simple and easy to fix. Thanks man. Also I think Dab Dan knows a thing or 2 about this subject.
a year later and the results are... ... ?
@@automotiveperformancemobil4030 @@
I have a 2000 Astro. Looked under hood and inside cab. Don't see no BTSI, IGN O, or TCM fuses. I did find a TRAN fuse in the cab, but it looks good.
I have a 05 chevy suburban was driving had acted like it went into neutral coasted to side of road lost all gears would not pull i checked shift cable good it moves no vlown fuses transmissionjust doesnt engage????
Mine just did the same thing. Did you figure out what it was?
Bad transmission fluid pump
Its a fuse!!!! Lmfao.
Rick Howard which fuse ?
I'm going to give your advice a try and check into the fuses I have a 05 yukon and the Trans was rebuilt at amco before I bought the truck Trans doesn't have 100000 on it yet I was driving the other day and noticed I didn't have 4th gear 123 and reverse work great smooth as can be no cel codes or Trans codes I did put a engine in that I put a stage 2 cam on but it's tuned at 276hp so it dosent damage the transmission
Great, doing troubleshooting/testing on the fuses first, but you have to look deeper...what is the actual 'cause' of a fuse blowing? My blown fuses always had an overload somewhere, so fix that too, or you'll be replacing fuses by the dozen.
Thank you
What fuses would it be man? would be a big help
Omg!! I spent all day changing the cylonids on my s10. Still no third or forth gear. I will check the dudes first thing in the morning!! Fingers crossed
OMG I Have a 1995 Sonoma we rebuilt it started up-cherry sounded better than before went a few miles then we couldn't shift to any gear. I really like this truck but aaaarg! It's driving me crazy
did that fix the problem?
@@bentsymbal3210 nobody answers
Did that work?
@@christianmotley262 see by them not answering gives us the answer yes it work & they cannot reply because they’re DRIVING lol
👍👍very helpful 09 same issues , check your fuses
If anyone can help I have a 2004 z71 Silverado after someone installed my stereo drive goes into limp mode but reverse works great and the transmission was perfect before radio install
Same thing
Did you ever figure out what It was?
Having a problem where my 2009’gmc Yukon only gose up to 2nd gear
Now you need to pull the wiring diagram and see what controls that circuit and start doing more diagnostics..a fuse doesn’t just blow for nothing
The owner that I had the truck before me the transmission went out on him had no reverse at all. So I bought the truck for $300 and spent $400 on a 4L60e with 200k miles drove it around town and when I took it 50 miles from my home town it said trans hot. Idle eng. Let it cool down and drove it back home. Truck only got 1st and 3rd gear no 2nd or reverse. Could it be the fuse?
I replaced the fuse and still don't have reverse.
Solenoid next??
sunshell broke?@@DGOUTDOORS01
Hello, my old automatic transmission moved on only one gear (like a reverse gear). I changed it, but the new one is same thing. I've tried new brain box, I've scanned the car, it shows no problem. I've had an electrician check the car and he said the fuse is good. Is it possible that the fuses are good but not receiving enough current or have some other issue?
You not a Dumb ass. YOUR A SAINT!!! Bruther bye posting this video you will have saved many hard working people THOUSANDS OF DOLLARS !!! GOOD KARMA IS COMING YOUR WAY ! Hundreds of rip off artists are now screwed because of this video. UA-cam has been a God send to the average working person that can't afford to get screwed over. Thank you from the bottom of my heart ! Bless You 🙏
Did you ever hook up to a scanner ? What did it say ? Mine said transmission component slipping ?
I have a 04 blazer. All gears work and are smooth but overdrive seems to stop working once warmed up. What do I need to check
Mine died on me while driving down the highway and wouldn't start and the shifter got stuck in second gear it would start out in drive but some down to second, what would cause that ?
It would slide down to second gear
You work on a 1997 2500 350 engine Chevy? I have one and I am not able to put any more money in mind.
I have a 99 tahoe seemed to work fine except it didnt feel like I ever had a passing gear in it put the gas all the way to the floor and it never kicked down . Also had a code for the A solinoid replaced It and the code stayed . Now the only way to get it to move is to run high fluid level and let it warm up. Any ideas? Aside from redoing the solinoid again will check fuses bit now that the fluid level is where it's supposed to be it wont move at all .
1500 bucks???? That s awesome! You can't buy a 4wd like that! In that condition here in Australia! Great vid btw! Cheers from Australia 🙂
I'm having the same problem with my 2003 Yukon Denali shifts perfectly 1-2 then when I'm driving 30mph doesn't shift to the 3rd one 🤔
I shall try the fuses Nd I'll will update so hopefully that's the problem
Ever figure out what was causing it? Mine is doing the same thing.
Did it work
Same here but it should be the 3 and 4 clutch that may burnt out
Having same issue did anyone ever figure this out
if no third it's probably the clutch patch burned out. If you have ONLY third then the transmission is in standby safe mode or whatever limp mode - and so probably electrical.
My transmission run but quits sometimes and I have to turn it off and turn it back on and it drives
Same! You ever fix that?
Yea , i removed the trans pan , changed my transmission filter and filled it back up
Was the "TCC" fuse on my 97 Cutlass surpreme
Damn my engine light just came on with the code p0740 . But my truck runs really good and shifts pretty smooth no problems whatsoever. Why would that light come on?
I have a 2004 chevy express 4.3 vortec the trans wont shift out of 1st how can i fix this ??? It just shifts real high still drives great tho
Mine does the same
What was it?
Great video like you said it was the fuse problem. Any chance you can tell us which fuse it was the problem?🙏
My 1995 6.5 diesel will go in park neutral reverse and 1st but won’t shift to 2/3/ overdrive
Whoever sold u the truck is definitely mad if they see this video and find out its a fuse! Haha
If your 2007 tahoe not going over 30mph is it your speed sensor
I’m having the same problem did you fixed your truck?
i have a '03 Chevy Z-71 4x4 extended cab i just replaced the 4L60E tranny with a rebuilt . i put on 825 miles on it since , running fine up until now. i was cruising down the freeway just fine and all of a sudden it just went out. pulled off the freeway and checked the fluid and it was fine. started to take off again and it was slipping real bad ... any ideas ?
Same here. Did you figure out the case?
What fuse was it do we know ?
Just replaced my gmc Sonoma tranny I paid to rebuilt it.. it's doing the same thing. Does this fuse come here too?
Mi 2000 chevy 4 wheel drive won't go an any gears. before I buy a new automatic transmission, is there any easy fixes like a bad furs or disconnected wires
You ever find out what's the problem? I'm having similar problems.
I am having problems with Our 2007 chevy suburban. We had a chevy place hook it up and said 02 sensors bad on drivers side changed both and sparp plug wires, engine idles, but when put in gear it stalls, wont shift and speedo not working.
Could be your throttle positioning sensor. There are two sensor/valve on the drivers side of the throttle body they are cheap and easy to change EGR valve and TPS sensor. Also clean your throttle body the 07 has electronic throttle so don't get your fingers cut off. Is the motor stalling or the transmission or both could be the brain or bad/burned wiring. I had an 03 that would idle faster and faster got dangerous, changed TPS/EGR next to it nothing helped. We plugged it to a computer and didn't read a problem. It ended up needing a new brain. I sold it as is and i still see it running around it had 265,000 when i sold it 3 years ago.
Definitely check the TPS
Also, VSS
this may be different then a fuse there is a sensor above your transfer case that may be bad check that
I need to give this a try i changed everything i possibly could in the pan and the speed sensor mine shifts perfectly but then not 3 or overdrive usually not that lucky but I'll give it a try thanks
did this work?
@isaiahsriojas2834 sadly it didn't
My truck does the same thing which fuse is it I have 2002 Chevy tahoe
I am having a similar problem I have a 99 Oldsmobile Alero 2.4 I changed all my solenoids and tfp switch and still my car won't go into gear I checked the transmission fuse it seemed to be fine I am at a lost can you possibly help me
Check if the VSS Vehicle Speed Sensor is bad, its a sensor on the outside of the tranny that registers speed & the engine computer knows when to shift gears. If its bad the speedometer will be erratic or does not work and the odometer may or may not work plus a bad vss will cause erratic shifts and it won;t shift into higher gears or overdrive. If the vss is good then you may need a partial or full rebuild, depends on all symptoms. Use google to find images of the vss location if you don't have a shop manual. Or search online forums for pictures. Good luck!
Omg I have a 1996 Chevy 1500 and it won’t shift into 3rd and this guy tells me I have no fluid in it .. he doesn’t know where it’s going .. so I need a new transmission more than likely $2000 bucks .,
Ok so it’s been sitting since December 2018.
Then my friend Phil has the same kind of truck. But I have a computer for my transmission.?????Something his doesn’t have. And things are disconnected.. hum wonder how that happened, and I have plenty of fluid..
so it could be a fuse?? I love it.. thank you so much...
It could be the 3-4 piston is shot, and need to replace 3-4 clutch pack with new piston, very common problem.
I’m gonna go try that right now God I hope it works
Did it work ?
Which fuse did you replace?
What exactly does that fuse abbreviation read. I don't have the book
BTSI fuse is what he changed
What does this fuse control
Christopher Williams I don’t see dat btsi fuse
Thanks
Thanks for the video which fuses were they
I have a 2000 gmc 3500 and trans is stuck in 2nd gear and converter is locked worked fine till had to replace ignition ass. In steering column now starts and runs great no shift any ideas
Is linkage cable all properly reconnected and not broken I.E. will the shifter move but the truck just stays in 2nd or will the shifter not move and is stuck in second. Really sounds like something didn't get put back together right if it was working fine before. You may have unhooked your shifting cable on accident.
was the ignition switch you put in it new, and non chinese made. I know in the 96, 97 era trucks would get stuck in a gear when it needed a new ignition switch. It may be a bad ignition switch not sending power back down to the transmission. I would bet that is your trouble.
ua-cam.com/video/sNaehHJl89E/v-deo.html hope this helps
I changed my fuse like u sead and it helped it went back to normal for a couple of days and now it's starting up again what should I do next??
Go to Walmart & buy a for sale sign 😂
did it shift fine when cold . I have one does same after warm . while cold does OK or it seems too
Rob Netherland mine does the same thing. its so frustrating. operates fine when its cold but when it warms up after a few miles it has no 3rd gear and up. stays in 2nd. feels like limp mode but the display isnt reading any code.
no mine was always doing it hot or cold.
@@Richard-md3gi my does tha same you fixed? Am still looking for some response.
@@Richard-md3giclogged converter?
I have a 2003 Chevy Trailblazer, I have to shift it into reverse 2 or 3 times for my truck to actually move in reverse. Could this be a fuse issue or does it sound like something else?
I would say a linkage issue or maybe solenoid problem. But for sure check fuses first.
I certainly have the fuses checked 1st, thank you 😊 yeah I read it could be a solenoid issue as well so I’m glad you second that suggestion that for me, thanks again
I hope it is nothing major be safe and thanks for watching
Tamekia Hall fuse r reverse solenoid
Nice job and Thankyou for the tip.
I have made the fuse mistake also and I know better.. keep truck'n
Damn hope the guy you bought it ftom don't see this lol
what would cause the fuse to go out?
They can wear out over time or ground out and pop
My 2001 suburban started to slip i believe , it shifts good 1st and 2nd then going into 3rd the gear doesnt go in and it idles really high, i have to release the pedal then push it fast so 3rd goes in ? Any ideas
Manuel Mejia im having that problem, did you ever get it fixed?
@@tonyloza4002 any update?
My 02 Escalade ext does the exact same thing...let off gas to get into 3rd will not go into 4th...1st n 2nd beautiful
I have a question my truck has the full power but dosen't shift to 3rd when I'm driving 1st and 2nd go in fine then the transmission downshifts to 1st and stays there what could it be if it's the solenoid which one could it be?
@Jason Carpenter no I cant find the problem I'm just going to replace it with a new transmission from the junkyard
@Jason Carpenter did you figure it out bro
3 and 4 clutch got burnt
@@fredrickmarrufo8074how’d it go?
@@KollynJ got rid of the truck a month after couldn’t find the problem and had to travel for work
Hey guys.
4l60e wont shift out into overdrive. Did shift out before fine.
Speed sensor went out replaced it. Now wont shift out into overdrive.????????
Help please
Did you solve your overdrive issue?
I got a 06 Envoy stuck in Dr will not go in reverse. At first it wouldn't go into 3rd or 4th gear what is causing all this
Sherman Golden did you fix it?
Thanks that really help!
Big help thanks
I have a Colorado that transmission work fine for about 1/2 mile then it is like it went to neutral. I can shut it off and restart then does same thing again.
I wouldn't know but maybe someone here will know and help you out. Sounds like it could be electrical by the way it resets back after restarting?
Pump or Sun shell if it goes into reverse then the pump rotor broke, the sun gear runs 2,3,R If the pump rotor is completely bad you will not have reverse or drive. But I have seen them where the rotor is cracked in half so it works at low rpms then when you Rev them up they don't work at all
My astro van wont reverse but drives foward i will check thank s
What was your problem?
Yeah I’m curious to know as well? My Chevy trailblazer is having that issue.
I have tahoe 2005
i change transmission oil and fillter . suddenly transmission works only in 3
hard and heavy stat drive it
our workshops not pro
they told me we must replace every thing inside transmission . including clutch
i need help for that issue
coz very expensive to do what they said to me
Abdulrahman Sulaiman I have the same problem
If you find a solution please guide me
Mohamed Fathy Someone fix my car
i asked him to chick fuses an selonoid
later he call me to take my car after he fix it . but unfurtunitlly he was very busy to let me know what he did to fix ghe problem
any way . I'll see what he did then I'll be back to you.
Abdulrahman Sulaiman your muslim. no help for you.
Abe T. المسلم كالشجرة المثمرة
أصلها ثابت وفرعها في السماء
لست بقلق من هذا الأمر
وقد جائتني المساعدة من الله عز وجل
صارت المشكلة في حساسات القير
my car problem was silenoed
need help please, chekd all fuses nd changed all 4 silinoids and still my truk is not shifting gears and my tac is not working. please any idea what that mayb?
What exactly is it doing, like no reverse or 1st and 2nd only or no transmission at all.
the service engine soon light came on, then the tach and speed ometer quit worrking.it's hard to get the shifter out of parkwe changed all the solenoids filter and fluid the truckwon't shift by itself. manuely no 3rd or overdrive it has reverse. thanks mikie.
tack is not working then its ur input/output transmission sensor .
bado2 sensor will tell computer to go into limp mode
easyrider1lv bartoli replace your VSS. That causes no tach issues
Thanks this really helped!
Hope this is what’s wrong with mines🙏🙏🙏Thanks in advance
Which fuse did you change, not this that an other, be specific
excuse me can u tell which fuse ?
I have yukon 2008 slt 4wd
transmission doesn't move to 2 ,3, 4 only on 1!!!!!
Christopher Williams7 months ago
the fuse he changed is called the BTSI( Brake Transmission Shift Interlock) fuel it should be next to the ac relay . Its a 10 amp red mini fuse.
Reply 9
Did it ever throw any check engine light? P0785 or P0753?
Which red 10 amp fuse did you replace
I changed a bunch out when I was replacing them and I didn't mark them but it was for sure on of those 5 I point at towards the end of the video sorry couldn't be more helpful
Not a bad truck for $1,500 bucks..... When that transmission craps out get a BULLRIPPER transmission. I have one in my 2004 Chevy Trailblazer EXT LS 5.3L it's a beast on the road.....
I will check them out, I hope this tranny lasts a little longer. Thanks for watching and the tip
we checked all the fuses under hood and on side of dashboard there ok
the fuse he changed is called the BTSI( Brake Transmission Shift Interlock) fuel it should be next to the ac relay . Its a 10 amp red mini fuse.
Which fuse was it
4th gear is overdrive.
Does anyone here know which fuses to check
01 silverado have to go low gear 1 or 2 then to drive to go..may it be fuses
sorry it took so long to reply I did not see until this morning! I would bet it is your fuses
@@landrun89 hope too good this is my problem! 1st second work when put in 3 or d it revs/misses I drove two hundred miles in second and no issues except for seems a little harder shifting!
Thanks bro
Was your abs and brake light on also did your speedometer work
Airsofters18 brake light was on but I had brake problems as well. the speedometer still worked
Airsofters18 both of mine are on. How does it play into this
Mine too.
Which fuse?? Haha im having the no reverse problem on 98 gmc jimmy
My 1999 merc mountaineer tranny was slipping in drive, added some fluid and started to run good and no slipping. Then vehicle made a hard kick bang sound and the vehicle wouldn't go forward anymore. Drove it 3 miles in reverse to house. Any info on what I need to look for. Thanks peeps 🙋
Manuel Ortiz i had that bang clunk when my 96 blazer tried to shift to 2nd gear one day. Will only go in 1st gear or reverse.
I have a 99 Escalade and I have to drive it at 24 mph before just switched to second gear could it be the fuse??
Did you ever find out what it was my 04 yukon is doing the same thing
Did some one fix that problem??
Look underneath by the passenger side front tire for the wire that goes to one of those solenoids make sure it didnt come lose my s10 did the same thing
I have a 93 Chevy 4x4 350 4l60e and it will shift from 1 to 2nd but not into 3rd or 4th it was shifting fine then just felt like it would go into neutral but when slowed down it would grab 2nd again. any ideas? thanks. my buddy says it's the vss? I have already changed the 2 sensors on tcase with no change. thanls
Brian Baker that is what mine did and it was just a fuse, could also be 3-4 solonoid. it was a 10 amp fuse that I point at towards the end of the video.
thanks for the reply when I go to my buddys house this weekend I'll make sure to check fuse and replace the solenoid. really hoping it's not the actual trans. I just bought the truck for 2500.
Did you figure it out just bought a 93 and wondering if that was youre issue mine is doing exactly the same
Mine is doing same thing, and I just replaced fluid, filter, and all the solenoids.. after second gear it’s like it’s in neutral ..
Mine is doing same thing, and I just replaced fluid, filter, and all the solenoids.. after second gear it’s like it’s in neutral ..
Did it say transmission hot when that happen?
no it didn't