MAX 232 DATA SHEETS
Вставка
- Опубліковано 9 гру 2022
- The MAX232 is an integrated circuit that converts the signals from a RS-232 protocol serial port to signals compatible with TTL or Cmos levels and vice versa, this for use in logic control circuits, which has a very special utility since it In control electronics, it is often necessary to exchange data between logic systems and power control systems, which are often far apart, so that communication is severely affected the more extensive the communication. distance between the control system and the power system and due to factors such as signal loss in the communication cables, inductance, interference etc, so to avoid all this it is necessary to convert the low voltage ttl or CMOS logic signals to standard rs232, and which work with voltage parameters of +/- 25v, thus reducing the signal/noise ratio, for this reason the max232 is useful as an interface for To transfer all the information between the two systems, but it is also useful to extract the data from the system LOG on television boards of certain generations that work with the rs232 protocol or even to program microcontrollers without the use of programming stations. So the MAX232 serves as a very convenient data transmit and receive interface for RX (receive data), TX (transmit data), and even CTS (clear to send) and RTS (request to send) signals. Therefore, the chip has two sets of independent data transmission and reception drivers.
PSALM 5:
• SALMO 5
Help us to continue uploading material of your interest. Thank you
www.paypal.me/oscarmillanzapata
Impresionante!!!
Hola Carlos muchas gracias por comentar, un abrazo y exitos
ua-cam.com/video/gFPMH-j4GZ8/v-deo.html
Hola maestro por aquí reportandome y como siempre un gran agradecimiento por su gran información sobre los componente que funcionan dentro d los aparatos electrónicos que la siga pasando muy bien
Hola Juan muchas gracias por tu comentario, un abrazo y muchos exitos!
ua-cam.com/video/Tf60RA-CBCU/v-deo.html
Muy interesante como siempre, saludos estimado amigo, abrazos!
Hola Gabriel muchas gracias por comentar, un abrazo y muchos exitos!
ua-cam.com/video/Tf60RA-CBCU/v-deo.html
Saludos. Me gusto mucho encontrar su video ya que estoy tratando de entender porque se daño mi shield RS232-TTL que usaba con Arduino. Estoy tratando de hacer un circuito y en una de las pruebas , coloque un puente del lado RS232: ósea el pin14 con el pin 13. Mi idea era ver si lo que entraba por el pin Tx TTL , salía por el pin Rx TTL. Observe que el integrado se calentó mucho, mientras ingresaban los datos y creo se daño la interface. Usted me puede ayudar con esa duda por favor.
Hola muchas gracias por comentar, creo que has planteado mal la pregunta puesto que Rx es recepción, no salida, al igual que Tx es salida y no enterada, quizá en eso consistió tu error, en un enlace de datos la conexión debe ser cruzada, es decir que la fuente de los datos (Tx) debe conectarse con Rx de la interfase y viceversa. Igual a mi nunca me gusta hacer puentes directos, yo siempre utilizo resistencias limitadoras. Un abrazo
Hola me ayudas ayer mi tele tubo se veia bien le puso undeco movistar hoy la prendi se escucha la voz pero la imagen no se ve y cuando la apago se ve la señal o sea se ve el canal que podra wer
Hola Isabela debes prueba reconfigurando el deco o reasignando la entrada de video. un abrazo
ua-cam.com/video/T437-o0YPNE/v-deo.html