I've been watching 'infeed support' videos all morning and I've got to say that I think that your video is the best. I love your design and your 'teaching instructions' have made it simple to construct. Thanks for the video.
Thanks! Here is my video about how I updated and added a new out-feed and side wing platform to my table saw cart. It may be helpful to you. ua-cam.com/video/uB6g0BmMJB0/v-deo.html
I enjoyed your presentation - very well done. I believe you would have made a great teacher as well. I made one of the UHMW boards to my existing table saw fence (Laguna fusion) a year or so ago but I forgot to change the measuring tape to accommodate the added width to my fence. Thanks for bringing that up in your video.
Great idea Ray! I just added (last week) the UHMW polypropylene board (24 in) to my fence. Great upgrade. I am going to upgrade my router table fence in the future and will use the existing fence material and upgrade to your design. Thanks.
Thanks for putting this video out on YT. This is a great idea and I think very helpful for longer narrow boards. Another challenge with the Dewalt saw is when using a cross cut sled. The in feed area is still too short. Have you any solutions for that? I have a similar cart to yours and am trying to figure out a way to install an in feed support behind the runner grove on the left of the blade to thus better support my cross cut sled. Thanks!
@@Ray_Here thanks for reply. Yea the square & flatness of plywood may be a issue. I was just trying not to spend $60 if I could do it with what I already have. Thanks again
I’m attaching two videos. One is a general upgrade to my stand. The other is an infeed support for the crosscut sled. Hopefully one will help you. ua-cam.com/video/uB6g0BmMJB0/v-deo.html ua-cam.com/video/8q0v23lGY0s/v-deo.html
I can’t argue your point. I’ve really not had it be an issue though. You just have to be mindful that if you push too hard against it, deflection is a possibility. Thanks for your opinion!
I've been watching 'infeed support' videos all morning and I've got to say that I think that your video is the best. I love your design and your 'teaching instructions' have made it simple to construct. Thanks for the video.
Thank you! You made my day!
Ray, thanks for the great idea! I have the same saw and also need to add an outfeed table like yours.
Thanks! Here is my video about how I updated and added a new out-feed and side wing platform to my table saw cart. It may be helpful to you. ua-cam.com/video/uB6g0BmMJB0/v-deo.html
Great video. Thanks for doing the research for the rest of us!
Thanks for the comment!!
Great job. If I hadn't had so many small hoarded MDF scraps, I'd have used sheet plastic too!
Thanks! I’m glad you liked the video.
I enjoyed your presentation - very well done. I believe you would have made a great teacher as well. I made one of the UHMW boards to my existing table saw fence (Laguna fusion) a year or so ago but I forgot to change the measuring tape to accommodate the added width to my fence. Thanks for bringing that up in your video.
Thanks you for your very kind words. I appreciate them!
Great idea Ray! I just added (last week) the UHMW polypropylene board (24 in) to my fence. Great upgrade. I am going to upgrade my router table fence in the future and will use the existing fence material and upgrade to your design. Thanks.
Thank you Brian! I appreciate you taking time to comment.
great idea, thanks for the tip 👍
Thanks. Glad it was helpful.
Interesting ideas !
Thank you!!
Great idea! I think I'll do the same for mine :)
Thanks for letting me know! I hope it works out for you.
Thanks for putting this video out on YT. This is a great idea and I think very helpful for longer narrow boards. Another challenge with the Dewalt saw is when using a cross cut sled. The in feed area is still too short. Have you any solutions for that? I have a similar cart to yours and am trying to figure out a way to install an in feed support behind the runner grove on the left of the blade to thus better support my cross cut sled. Thanks!
Try this. ua-cam.com/video/8q0v23lGY0s/v-deo.html
Great idea. I think a company copied your idea very recently; seriously, but I can’t recall the name.
@@acrocha1222 Well, if they did, I’m flattered! Thanks for the comment!
Nice project, good video! Which dowel jig do you have? Do you like it?
Thanks. The centering jig is by O’Skool. Here’s the link. a.co/d/dDyrfPt
Good video. I've been trying to figure out something exactly like you show. Do you think this can be done with some 3/4" birch plywood?
Thanks. That would probably work. Just make sure it’s flat. Good luck!
@@Ray_Here thanks for reply. Yea the square & flatness of plywood may be a issue. I was just trying not to spend $60 if I could do it with what I already have. Thanks again
Hi Izzy
I would like to order one if it’s available
I have Dwe 7491RS
Hi! I think you meant to leave your comment on Izzy Swans channel.
I’m attaching two videos. One is a general upgrade to my stand. The other is an infeed support for the crosscut sled. Hopefully one will help you. ua-cam.com/video/uB6g0BmMJB0/v-deo.html ua-cam.com/video/8q0v23lGY0s/v-deo.html
"Deflection" is the very reason to not make this with "Nylon"
I can’t argue your point. I’ve really not had it be an issue though. You just have to be mindful that if you push too hard against it, deflection is a possibility. Thanks for your opinion!