You forgot to mention that the LEDs inside the lamp is at HIGH mains voltage (depending on lamp design) since there uis no galvanic isolation and pose a SERIOUS risk should you inadvertantly touch any of the components on the PCB. Do not try this at home!
The voltage and current at the LED terminals won't possibly harm you as they are downsized by the circuitry. Of course, any electric work is inherently dangerous and a warning was appropriate.
@@gopalakrishnanmsYou willing to bet your life on that? First, they're wired in series.10 LEDs equals about 35V. The current is enough to kill you... takes hardly any. More to the point, we don't know why the unit failed. Maybe the voltage is too high. Lastly, as I said, they're wired in series. The foil bridge has little resistance, which means the voltage for 10 is now divided between 9 LEDs. They'll run hotter. If they cause a fire and that modification is discovered, your insurance claim will be refused. You could kill yourself or worse, someone else.
Soldering a decent sized wire in place of the dead LED would make a much better contact than gluing aluminum foil across the contacts. You might get an intermittent connection and arcing. Replacing the LED would be the best. Keep a donor bulb to fix others that fail.
Do not solely rely on the switch before starting to remove the LED. Most of the switches cut the current on one line, therefore if you connect the switched line to Neutral (you have 50% of chance) then the live line will not be interrupted and you may get a shock when you touch the burned LED (depending on the position of the LED on the LED string, especially if it's close to the high voltage side) with a conductive tool. Totally unplugging the system from the mains is the best choice.
Better way to do #2, just fill the existing hole with superglue, let it sit overnight & screw the hinge back in place. The fiberboard will absorb some of the superglue, the rest will harden in place, and you'll have a small dimple in the center where the screw goes. For hardwood doors, use superglue or wood glue and a toothpick or small diameter dowel.
"use superglue or wood glue and a toothpick or small diameter dowel" .....and go the added effort of centering the holes. That hinge isn't going to re-install properly.
سلام از ایدههای شما استفاده میکنم و بسیار علاقهمندم من این روش را تجربه کردم و عمر لامپ بعد از تعمیر کمتر از ۷ روز مجدد میسوزه،ولی این روش برای لامپهای بالاتر از ۲۰ وات بسیار مفید و عمر لامپ طولانیتر است. موفق باشید💐
On #2, you could have just stuck toothpicks in the original holes and screwed everything back in place. The screws create new threads in the toothpick as you screw it down. Much easier than what was shown here.
I clean my aluminum foil with aluminum foil so I can reuse it. When the aluminum foil i use to clean the other aluminum foil gets dirty i take another piece of aluminum foil & use it to clean the aluminum foil that i use to clean the aluminum foil so i can use it again.😊
That loose illumination LED didn't necessarily need to be removed. A quick dab on either side with a drop of new solder would have gave it new life, if it was loose due to insufficient solder.
That sounds interesting! What's the purpose of pouring glue on aluminum foil? Is it to create a new super adhesive or just to test the glue's features?
@@maricarmenjordantorrent7575I'll bet they haven't caused a fire either... yet. LEDs are meant to last a very long time, so there's a good chance there's a fault in the circuitry, then you add 10% more voltage to each led. If they cause a fire and the modification is discovered, your insurance claim will be refused.
Some interesting ideas. I’m not sure I’d take the time to deal with an LED bulb like that though. It was still a “shaky” lightbulb. That would drive me crazy.
If you wish to clean Silver Jewlery or Silver plated utensils, put Aluminium foil in a basin, pour in hot water that has Sodium Bicarbonate dissolved in it & then put the Silver objects in so they touch the Aluminium. Wow! they clean immediately as they touch the foil.
Since you had a soldering iron as in #6, why didn't you just use that to fix that LED bulb? A single drop of solder bridging the pads for that bad LED is all it would need. However gluing a piece of foil over them will result in a poor mechanical connection when the board heats up, and possibly even a high-resistance connection that will heat up and possibly start a fire. Use the right tools and methods for the job.
Do NOT use salt to clean your sterling silver! Salt might work on steel but it will darken your silver and you might not be able to fix it without a jeweler doing it for you. Cleaning silver is putting crumpled aluminium foil in a dish, add the sterling (.925 stamp) silver you wish to clean, then baking soda then hot water. I don't think the order matters, this is how I do it. It doesn't take an hour and you can watch the tarnish diminish within a minute. Contact with the foil is important so you might want to use fresh foil, fresh hot water and baking soda, turning the silver over so all of it contacts teh foil with the baking soda. Then rinse in clear water and dry. This also cleans the crevices of intricate designs. I've used it for years.
Great....and aluminum tape is my personal god of cheap fix great strength and best if two or three layers are used, small wrinkles are like ribs of strength
I'd use a wooden dowel or wood shavings & wood glue let dry then screw the hinge in for number 2. The led light trembling and flickering like that is not something I care to have in the house, it would make me batty. Cool other wise, thanks
Please don't take this personally, but number 4 is one of the worst ideas I've seen. It is dangerous, for two reasons. First, you never work on anything while it is plugged in. You should edit the video to put a warning message about that, immediately. 4:04 Secondly, if one led can stop the rest of the leds lighting up, that means they are wired in series. This in turn means that each of the ten leds gets the right voltage ONLY when there are ten of them. Leaving only nine means each one is getting about 10% higher voltage. They'll run hotter. They could cause a fire. If they do, and the fire department finds your led bulb, and can see the modification you made, your insurance won't pay out. That's a good outcome... a bad outcome is you kill yourself... a devastating outcome is you kill others. Yep, number 4 is a very, very bad idea.
❤sizin bilgilerden çok yararlanıyorum bazı bilgilerden bende çkk büyük fikirler çoğalıyor umut ediyorumki bu bilgi çeşitliluğinden daha fazla atılımlar göstereceğim başarılarınız daim olsun eğitimsisteminiz güzeliklerle dolsun saygılarımla
Thank you Creativeholic for this handy video. Thank you to the Community Members who also provided useful information as well. Best Wishes to all of you!
Only if trump gets elected and tries to turn America into a fascist country. As a country, our economy is strong, manufacturing is having a boom, workers are forming unions and gaining the higher wages they’ve earned, we’re defending an ally from invasion by a different fascist leader. What they haven’t done is add 8 trillion to our national debt by giving ridiculously high tax breaks to the rich and himself, like trump did. And now, as usual, it’s up to the Democrats to repair the damage. Which we will.
Cleaning iron based tools with Aluminum foil would cause more corrosion due to galvanic corrosion effect on the Residual aluminum. Unless you can ensure it either covers whole surface OR no residue is left. I get that these are quick fixes for when you can't go to the store but having a piece of sand paper at home is a must. If needed use wet sand, but make sure everything is dry and properly lubed. Also make sure the sand is course enough not to get stuck in hinges.
"Wow, this video blew my mind! Using aluminum foil and super glue to fix various items is such a genius idea. I never thought these everyday materials could be so versatile. Can't wait to try out these hacks myself!"
Molto interessanti le idee che ci hai consigliato e possono ottenere!. risparmiando, riuscendo, aggiustando, con il fai da te: con le nostre mani dà molte soddisfazioni gratificazioni!. Io sono dell'Italia centrale🇮🇹 sul Mar Adriatico Buon lavoro idee, ai prossimi video Buone Sante Festività!.
An einer Birne Manipulationen vorzunehmen die noch mit dem Stromnetz in Verbindung steht halte ich für Riskant. Der läppische Zwischenschalter blockiert nur eine zuführende Ader. Liegt hier ein Defekt vor kommt es zu einem eventuellen Stromschlag. Ansonsten sind ihre Reparatur Tricks hervorragend - Danke 😊
I, Was actually Wondering IF the Inner Mechanics of the Light would be a resister? But... If the Thought of Ohms of resistance is there. Maybe Forget that Idea.💡 Does look cool Though.
You did not just risked yourself and taught kids to risk themselves getting electrocuted to smithereens to save $2 bucks ? Dude.
I think it's quite simple
Yeah it's simple... you disconnect the power before doing any work on mains powered equipment.
You forgot to mention that the LEDs inside the lamp is at HIGH mains voltage (depending on lamp design) since there uis no galvanic isolation and pose a SERIOUS risk should you inadvertantly touch any of the components on the PCB. Do not try this at home!
And as the resistance is lower now, all the other led's will went wrong quickly.
Hello! thanks for your comment. Wish you all the best!
I see... the aluminum foil with the super glue helps you put your hinge on crooked. Nice!
Thanks so much for watching our video. Wish you all the best
I got to a minute 28 and saw that too. No idea what the rest shows...
Great hacks except for #4 which is downright dangerous.
Hello! thanks for your comment. Wish you all the best!
You mean you don't do electrical work on stuff that's plugged into an active source? What could possibly go wrong? 😅
The voltage and current at the LED terminals won't possibly harm you as they are downsized by the circuitry. Of course, any electric work is inherently dangerous and a warning was appropriate.
I like this no. 4th to try
@@gopalakrishnanmsYou willing to bet your life on that?
First, they're wired in series.10 LEDs equals about 35V. The current is enough to kill you... takes hardly any.
More to the point, we don't know why the unit failed. Maybe the voltage is too high.
Lastly, as I said, they're wired in series. The foil bridge has little resistance, which means the voltage for 10 is now divided between 9 LEDs. They'll run hotter. If they cause a fire and that modification is discovered, your insurance claim will be refused. You could kill yourself or worse, someone else.
That LED isn't going to last without the proper ohms
Hello! thanks for your comment. Wish you all the best!
Soldering a decent sized wire in place of the dead LED would make a much better contact than gluing aluminum foil across the contacts. You might get an intermittent connection and arcing. Replacing the LED would be the best. Keep a donor bulb to fix others that fail.
@@beku2283 ohms is most important...a decent size wire is too arbitrary and will burn out faster.
Just buy a new one. I hate when people do this
@@anthonybasile5035 🤣🤣🤣
For number 2 use a few toothpicks and a bit of wood glue or even simple white glue.
I agree...toothpicks are a zillion time faster n easier than all those steps!
Hello! thanks for your recommendation. Wish you all the best!
Saw-dust mixed with woodglue using a dowel or toothpick. Keep your saw dust and wood-chips for these repairs.
*I use UV cure glue and clear food wrap and stuff it in the hole. Light it up with UV flashlight for 5 seconds and its ready for screws.*
Do not solely rely on the switch before starting to remove the LED. Most of the switches cut the current on one line, therefore if you connect the switched line to Neutral (you have 50% of chance) then the live line will not be interrupted and you may get a shock when you touch the burned LED (depending on the position of the LED on the LED string, especially if it's close to the high voltage side) with a conductive tool. Totally unplugging the system from the mains is the best choice.
Hello! thanks for your comment. Wish you all the best!
Better way to do #2, just fill the existing hole with superglue, let it sit overnight & screw the hinge back in place. The fiberboard will absorb some of the superglue, the rest will harden in place, and you'll have a small dimple in the center where the screw goes. For hardwood doors, use superglue or wood glue and a toothpick or small diameter dowel.
Hello! thanks for your comment. Wish you all the best!
wood glue + sawdust 👍 = best
"use superglue or wood glue and a toothpick or small diameter dowel" .....and go the added effort of centering the holes. That hinge isn't going to re-install properly.
Thanks you😊
#2 was crooked due to poor alignment. I would rather follow your advise, than videos as holes are not enlarged and easier to aim at
I roll up aluminum foil into a ball to clean the grates in my charcoal grill. Works great.
Great tip!
سلام از ایدههای شما استفاده میکنم و بسیار علاقهمندم
من این روش را تجربه کردم و عمر لامپ بعد از تعمیر کمتر از ۷ روز مجدد میسوزه،ولی این روش برای لامپهای بالاتر از ۲۰ وات بسیار مفید و عمر لامپ طولانیتر است.
موفق باشید💐
Thank you for sharing your feedback. You can weld it for longer life
On #2, you could have just stuck toothpicks in the original holes and screwed everything back in place. The screws create new threads in the toothpick as you screw it down. Much easier than what was shown here.
Hello! thanks for your recommendation. Wish you all the best!
Thank you, very useful tips with things at home. Great when you're in a hurry or for an even elderly woman on their own .
Hello! I am very happy to read your comment. Have a good day!
いいもの観ちゃった！
ありがとう！
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
I clean my aluminum foil with aluminum foil so I can reuse it. When the aluminum foil i use to clean the other aluminum foil gets dirty i take another piece of aluminum foil & use it to clean the aluminum foil that i use to clean the aluminum foil so i can use it again.😊
That's such a great idea
That loose illumination LED didn't necessarily need to be removed. A quick dab on either side with a drop of new solder would have gave it new life, if it was loose due to insufficient solder.
Thank you! Cheers!
That sounds interesting! What's the purpose of pouring glue on aluminum foil? Is it to create a new super adhesive or just to test the glue's features?
Pour glue on the aluminum foil to create a bond and make it more sturdy
Un led menos recarga los otros. Pronto se quemara la bombilla.
Pues yo he arreglado varias hace meses y siguen funcionando.
@@maricarmenjordantorrent7575I'll bet they haven't caused a fire either... yet.
LEDs are meant to last a very long time, so there's a good chance there's a fault in the circuitry, then you add 10% more voltage to each led.
If they cause a fire and the modification is discovered, your insurance claim will be refused.
Most of them get refused anyways
these days the thieving tapeworm
son's of bitches!
Thanks, thats 6 mins I'll never get back.
Thank you! Cheers!
super glue costs more than the led bulb
In my country it costs 0.5$, make sure it is "cyanoacrylate adhesive glue"
@@creationholic101thanks
If the switch at 3:00 min is SPST, you should be at danger... It should be DPST switch. Or you have to disconnect the plug from the main socket.
Hello! thanks for your comment. Wish you all the best!
شكرا لك على هذا الفيديو المفيد انا من الجزائر
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Thank you for all these exemples. With these knowledge i can make a lot of repairing
Glad it was helpful!
To the first “tip” - steel wool would do the same job cheaper…😉
Hello! thanks for your recommendation. Wish you all the best!
Some interesting ideas. I’m not sure I’d take the time to deal with an LED bulb like that though. It was still a “shaky” lightbulb. That would drive me crazy.
I understand your concern! Make sure you have safety equipment in place before doing so
@@creationholic101😊😊😊😊😊 il 😂😅 mi
7😊😅 hu 😅 hu tu 😊
.y numuku Lloyd's KK o se la ok look 9!😊😊😊
Ma oggi nn
😅🎉😅😅😅u. G
Y😅😅 MM😢o II.
@@creationholic101😅😅😅😅😅😅😮 fammi II pollo pollo solo se nn
Buon
😮
Lo lum in😊😊un u in
Its only by camera rekord, not visible blinking for eye
If you wish to clean Silver Jewlery or Silver plated utensils, put Aluminium foil in a basin, pour in hot water that has Sodium Bicarbonate dissolved in it & then put the Silver objects in so they touch the Aluminium.
Wow! they clean immediately as they touch the foil.
Cleaning silver, gold, with Toothbrush and toothpaste. Top 👍👍
Hola. Saludos desde Medellín-colombia.
Muy interesante los videos. Se aprenden muchos trucos.
Glad it helped!
Since you had a soldering iron as in #6, why didn't you just use that to fix that LED bulb? A single drop of solder bridging the pads for that bad LED is all it would need. However gluing a piece of foil over them will result in a poor mechanical connection when the board heats up, and possibly even a high-resistance connection that will heat up and possibly start a fire. Use the right tools and methods for the job.
I want to give more measures to people who don't have a soldering iron
This is someone who loves AU foil!
I think anyone would love gold foil. Alum8nium is Al.
AU is the atomic symbol for gold. AL is the atomic symbol for aluminum.
De Valladolid, España Adelante. Os vemos con gusto.
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Using staples is a great idea!
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
3:14 the failed LED already had a dot on it. 😁
Please try and feel
잘 봤습니다 😊👍
Glad you like them!
素晴らしいアイデアです👏👏👏👏👏
Thank you! Cheers!
I use aluminium foil to clean the aluminium engine casings with aluminium cleaner
That's a good idea!
بنده از ایران بیننده برنامههای آموزنده شما هستم
بسیار عالی و آموزنده
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
WTH am I doing with my life??? 🤔🤔🤬🤬🤬
Thank you for watching
Do NOT use salt to clean your sterling silver! Salt might work on steel but it will darken your silver and you might not be able to fix it without a jeweler doing it for you. Cleaning silver is putting crumpled aluminium foil in a dish, add the sterling (.925 stamp) silver you wish to clean, then baking soda then hot water. I don't think the order matters, this is how I do it. It doesn't take an hour and you can watch the tarnish diminish within a minute. Contact with the foil is important so you might want to use fresh foil, fresh hot water and baking soda, turning the silver over so all of it contacts teh foil with the baking soda. Then rinse in clear water and dry. This also cleans the crevices of intricate designs. I've used it for years.
Hello! thanks for your comment. Wish you all the best!
Also great for cleaning bbq grill, reflecting/directing wifi signal, and emergency auto fuses (good excuse to always have gum in your car.
That's a great idea!
Muy buen vídeo repleto de excelentes ideas, gracias por compartir.
Hello! I am glad you like this ideas. Wishing you all good things!
A simple blob of solder across the LED terminals is so much easier and permanent.
Hello! thanks for your comment. Wish you all the best!
You are amazing man!
We look forward to teaching you new tricks.
Sincerely yours
from Iran
Thank you! Cheers!
Great....and aluminum tape is my personal god of cheap fix great strength and best if two or three layers are used, small wrinkles are like ribs of strength
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Good time, teacher, your works are really beautiful 💖🤌👍🌹 and unique 💖💖
Thank you! Cheers!
Desde España. Muy buenos trucos. Muy útiles. 😊
Glad you like them!
Thank you, my friend, and I wish you good luck and success
Thank you too
Thanks for your ideas. It is very useful for me. I'm from Ukraine.
Glad it was helpful!
Those ideas with aluminum are not bad
Thank you! Cheers!
Your ingenuity is purposeful and boundless!!! Keep it up!!! Genius and waste not want not are always appreciated!!! Robert W Goodwin MD aka Db
Thanks so much for watching our video. Wish you all the best
This guy can fix any thing, wow🎉
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
MacGyver
It was very informative and useful, thank you dear ❤
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
I'd use a wooden dowel or wood shavings & wood glue let dry then screw the hinge in for number 2.
The led light trembling and flickering like that is not something I care to have in the house, it would make me batty. Cool other wise, thanks
Thank you for sharing your feedback. Have a good day!
Ciao, ho guardato il tuo video dalla Romagna Italia, grazie per avere mostrato come risolvere alcuni problemi.
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Please don't take this personally, but number 4 is one of the worst ideas I've seen.
It is dangerous, for two reasons. First, you never work on anything while it is plugged in. You should edit the video to put a warning message about that, immediately. 4:04
Secondly, if one led can stop the rest of the leds lighting up, that means they are wired in series. This in turn means that each of the ten leds gets the right voltage ONLY when there are ten of them. Leaving only nine means each one is getting about 10% higher voltage. They'll run hotter. They could cause a fire. If they do, and the fire department finds your led bulb, and can see the modification you made, your insurance won't pay out. That's a good outcome... a bad outcome is you kill yourself... a devastating outcome is you kill others.
Yep, number 4 is a very, very bad idea.
Hello! thanks for your comment. Wish you all the best!
Excelente canal me encantan los trucos caseros
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Excellent examples and demonstrations. Very usefull thank you
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
❤sizin bilgilerden çok yararlanıyorum bazı bilgilerden bende çkk büyük fikirler çoğalıyor umut ediyorumki bu bilgi çeşitliluğinden daha fazla atılımlar göstereceğim başarılarınız daim olsun eğitimsisteminiz güzeliklerle dolsun saygılarımla
Glad it helped!
"May your education system be filled with beauties" I hope that's Google's misinterpretation and not what you actually said?
I have benefited a lot from these videos, thank you
Glad it helped!
Bonjour de France, et merci!
Welcome to Creation Holic channel! Hope you have a good time while watching the video
I'm from Iran❤❤❤❤❤❤❤❤❤❤❤❤❤
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Thank you much solutions
Happy to help
I like that LED light cheat❤❤
Thanks so much for watching our video. Wish you all the best
Thank you Creativeholic for this handy video. Thank you to the Community Members who also provided useful information as well. Best Wishes to all of you!
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
Being raised in a poor family, I can dig this. Hell, the way the political future looks, ALL OF US are going to need survival tactics. 😢😢😢
O
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Only if trump gets elected and tries to turn America into a fascist country.
As a country, our economy is strong, manufacturing is having a boom, workers are forming unions and gaining the higher wages they’ve earned, we’re defending an ally from invasion by a different fascist leader.
What they haven’t done is add 8 trillion to our national debt by giving ridiculously high tax breaks to the rich and himself, like trump did. And now, as usual, it’s up to the Democrats to repair the damage. Which we will.
No, my friend, all of YOU, Not US.
UNFORTUNATELY, you're right! 😢😢😢
çok güzel videoların var. Teşekkür ederim.
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Thanks! Brazil!
Thank you! Cheers!
Thank you very much
Hi. Thanks for visiting my channel. What idea would you like me to do in the next video?
@@creationholic101 anything thank very much
These diys are what keep me up late at night. I also 'travel' a lot, lol
Glad you like them!
Hmm, I know what you mean man
Cleaning iron based tools with Aluminum foil would cause more corrosion due to galvanic corrosion effect on the Residual aluminum. Unless you can ensure it either covers whole surface OR no residue is left. I get that these are quick fixes for when you can't go to the store but having a piece of sand paper at home is a must. If needed use wet sand, but make sure everything is dry and properly lubed. Also make sure the sand is course enough not to get stuck in hinges.
Thank you for sharing your feedback. Have a good day!
Shortening the broken LED is dangerous, because drop of voltage is decreased.
Please wear safety equipment when repairing
I'm from Vietnam 😊
Welcome to Creation Holic channel! Hope you have a good time while watching the video
"Wow, this video blew my mind! Using aluminum foil and super glue to fix various items is such a genius idea. I never thought these everyday materials could be so versatile. Can't wait to try out these hacks myself!"
Thank you! Cheers!
These are good ideas,
Glad you like them!
Molto interessanti le idee che ci hai consigliato e possono ottenere!. risparmiando, riuscendo, aggiustando, con il fai da te: con le nostre mani dà molte soddisfazioni gratificazioni!. Io sono dell'Italia centrale🇮🇹 sul Mar Adriatico Buon lavoro idee, ai prossimi video Buone Sante Festività!.
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
No 3, use washing soda not salt and the tarnish on silver will disappear instantly.
Thanks for sharing!
Thanks for the tip
Thank you! Cheers!
Thanx for your great tips.
Glad you like them!
Muy buenos tips
Glad you like them!
USA ,Michigan
Thank you for watching
An einer Birne Manipulationen vorzunehmen die noch mit dem Stromnetz in Verbindung steht halte ich für Riskant. Der läppische Zwischenschalter blockiert nur eine zuführende Ader. Liegt hier ein Defekt vor kommt es zu einem eventuellen Stromschlag. Ansonsten sind ihre Reparatur Tricks hervorragend - Danke 😊
Hello! thanks for your comment. Wish you all the best!
Ik kom uit Nederland en kijk graag je filmpjes.
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
It deems like a lot of extra work.
Thanks so much for watching our video. Wish you all the best
From Greece
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Hello!! thanks!! From Seville, Spain
Welcome to Creation Holic channel! Hope you have a good time while watching the video
Xalapa Ver. México, tu canal es muy bueno. Gracias por compartir tantos tips. Feliz año nuevo.
Thank you, wish you a happy and joyful new year
Good video prayers for you and yours
Thank you so much 🤗
What superglue do you use ?
cyanoacrylate adhesive glue
شكرا هذه الافكار.
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
Im afgan its very good
"Hello! Welcome to Creation Holic channel! I am glad you like this ideas. Wishing you all good things!
"
Step 4: How to burn your house down while you're asleep.
it's pretty safe in case you haven't bought that new device yet
Ide yang keren
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
@@creationholic101 ☕️
Super glue....4.59
Foil paper......4.29
Fine sand paper... 0.99
You pick!
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
I'm from Brazil and thank you for creating this public service channel, it's a 10....👏🏻👏🏻👏🏻👏🏻👏🏻
Hello! Welcome to Creation Holic channel. I am very happy to read your comment. Have a good day!
你好我來自台灣，請問陽台的遮雨棚，有破洞要用什麼來修？謝謝你
you can refer to this video
ua-cam.com/video/q8JBsNyIgUE/v-deo.html
Bombaaaa very good man Thank You Very Much🙂
Thank you so much for your positive feedback! I'm glad you enjoyed the video and found it helpful
Lamp can not light because some of them defect and led connect in series togeter. so bypass with conductor metal
Please try and feel
Fantástico, muito bom.
Thank you! Cheers!
Gary from Oklahoma USA Thumbs Up!
Welcome to Creation Holic channel! Thanks so much for watching our video. Wish you all the best
Sei un genio ora so qualcosa che prima non sapevo👍💯🤗
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!
Nice hacks; hopefully no one electrocutes themselves fixing a light bulb.
Thank you so much for your comment! have a nice day!
Safety 1st, wear a crash-helmet incase you get a jolt by touching a capacitor, it will send you flying...or worse.
Good idea
Many many thanks
I, Was actually Wondering IF the Inner Mechanics of the Light would be a resister? But... If the Thought of Ohms of resistance is there. Maybe Forget that Idea.💡 Does look cool Though.
Welcome to Creation Holic channel! Thank you so much for your comment! have a nice day!