How I Fixed A Broken FLEX CABLE INSTANTLY! | Mr Biomedical

Поділитися
Вставка
  • Опубліковано 23 гру 2024

КОМЕНТАРІ • 70

  • @BetterBiomedChannel
    @BetterBiomedChannel 2 роки тому +21

    I place clear plastic heavy duty tape over the repaired cable to also limit flex and support the cable

  • @dagvidarsigvartson6291
    @dagvidarsigvartson6291 Рік тому +12

    How many degrees you use on your soldering iron.I am afraid to burn the ribbon cable with to high heat?

    • @MrBiomedical
      @MrBiomedical  Рік тому +5

      It wont burn, just apply by heated lead

  • @lisay5047
    @lisay5047 Місяць тому +1

    How are you able to keep the solder from overflowing and jumping between lines? It looks like you are somehow able to wipe between the lines at 4:00. Thanks!

    • @MrBiomedical
      @MrBiomedical  Місяць тому +1

      Simple.. you should use proper solder flux. It will do a magic

  • @DavidBlakemore-kn1ov
    @DavidBlakemore-kn1ov Рік тому +5

    looks good, the flux was important?? 5 ribbon circuits???

  • @naomfaigel
    @naomfaigel 2 місяці тому +1

    Hi, Thanks for the video. What do you use to peel the cable? I can't find the right tool. Thanks

    • @MrBiomedical
      @MrBiomedical  2 місяці тому +2

      I am using sharp surgical blade

  • @jasminerogers9971
    @jasminerogers9971 7 місяців тому +1

    So did you scape the coating off with heat ? Or just used the tool alone ?

  • @cslee6353
    @cslee6353 9 місяців тому +2

    when can I find replacement flex cable?

  • @brahmanroadjorhaturban1498
    @brahmanroadjorhaturban1498 2 роки тому +3

    What fluid you applied after cleaning the flex

    • @bassfear_9952
      @bassfear_9952 2 роки тому

      special uv light glue specially for this aplication
      dont know what its called exactly

    • @brahmanroadjorhaturban1498
      @brahmanroadjorhaturban1498 2 роки тому

      @@bassfear_9952 so can I use tape in place of this glue

    • @olehcelsior1005
      @olehcelsior1005 Рік тому

      ​@@brahmanroadjorhaturban1498yes, preferably thermal resistant capton tape

    • @MrBiomedical
      @MrBiomedical  Рік тому +1

      UV mask

    • @MrBiomedical
      @MrBiomedical  Рік тому +2

      It is called UV mask

  • @CamronLumm
    @CamronLumm Рік тому +2

    what do you scratch the ribbon with?

  • @brahmanroadjorhaturban1498
    @brahmanroadjorhaturban1498 2 роки тому +1

    And can I use regular tape in place of gum you added at last?

    • @MrBiomedical
      @MrBiomedical  2 роки тому +1

      Depends on how hard it will hold

    • @brahmanroadjorhaturban1498
      @brahmanroadjorhaturban1498 2 роки тому

      @@MrBiomedical what fluid u used after cleaning the flex and is it compulsory?

    • @MrBiomedical
      @MrBiomedical  2 роки тому +1

      It is UV mask. It is necessary to bond the connection

  • @NikhilGarlapati
    @NikhilGarlapati 3 місяці тому

    is kapton tape enough or is uv soldermask needed?

    • @MrBiomedical
      @MrBiomedical  3 місяці тому

      UV solder mask is better than that

  • @mohamadfahmibinmatrohim3683
    @mohamadfahmibinmatrohim3683 Рік тому +3

    Can u name 2 type paste that u use? The brand

  • @lexanausa
    @lexanausa 4 місяці тому

    Do you offer repairing items like this? We have one that needs to be soldered to a board.

    • @MrBiomedical
      @MrBiomedical  4 місяці тому

      Can you send me the picture of that item? 9790567867

  • @krystala.miranda6785
    @krystala.miranda6785 11 місяців тому

    what did u use to clean it up?

  • @maurasanthony4566
    @maurasanthony4566 10 місяців тому +3

    Though the job is done, after the work that part becomes stiff and no longer flexible.Linking the tracks with thin insulated wire would give more flexibility.

    • @MrBiomedical
      @MrBiomedical  10 місяців тому +2

      Yes true. But for my application it was enough. That is what

    • @brisketea2438
      @brisketea2438 20 днів тому

      This is necessary if you ever run into a situation where you can not get replacement parts and this is the only option

  • @HoustonTexas-m4r
    @HoustonTexas-m4r 6 місяців тому +3

    This is an old type of the ribbon cable. Most of modern ribbons cannot be soldered.

  • @ztipster
    @ztipster 11 місяців тому

    Is it a problem if one path connected to the one beside it ?

    • @MrBiomedical
      @MrBiomedical  11 місяців тому +1

      Not a problem until you connected it correctly

    • @ztipster
      @ztipster 11 місяців тому

      ​@@MrBiomedicalso if a solder connected two paths wont be a problem? Because it is spaces between paths are so narrow

    • @MrBiomedical
      @MrBiomedical  11 місяців тому

      @ztipster in that case u should need to use number wire

    • @ztipster
      @ztipster 11 місяців тому

      @@MrBiomedical what is number wire ?

    • @MrBiomedical
      @MrBiomedical  11 місяців тому

      Sorry, jumper wire I meant

  • @RynaxAlien
    @RynaxAlien 11 місяців тому

    Can broken tiny leads be detected visualy in flex cables?

  • @العلممسائلودلائل

    So why do we apply uv light?

  • @UhOhStevie
    @UhOhStevie 2 роки тому

    What’s the name of the song?

  • @PerfsThePiper
    @PerfsThePiper Рік тому +1

    Hi bro, that's amazing recovery. I have a flex ribbon which requires some workm any chance I can ship it over to you for you to have a look? Let me know bro. Thanks

    • @MrBiomedical
      @MrBiomedical  Рік тому +1

      Yes, you can send me. More details please WhatsApp 9790567867

  • @RetroRepair
    @RetroRepair 16 днів тому

    It's a shame that this doesn't apply to most repairs that have to flex on exactly that point. Good job though

  • @fraoltamiru5079
    @fraoltamiru5079 2 роки тому

    What is the name of that fluid??

  • @loryjeannemalate2949
    @loryjeannemalate2949 3 місяці тому

    can I use this method on an iphone flex cable? the repair shop accidentally ripped them 😭😭

  • @danikoo582
    @danikoo582 8 місяців тому +1

    I have to do that on a flat cable about 5 times smaller than that 😅

    • @MrBiomedical
      @MrBiomedical  8 місяців тому +2

      Then u should need that level microscope

  • @franciscovillalon
    @franciscovillalon Рік тому +1

    Good video

  • @speakersteve9586
    @speakersteve9586 5 місяців тому

    Can I send you a flex cable for repair?

  • @irshathsd
    @irshathsd 2 роки тому +2

    Perfect

  • @abdullaha2002
    @abdullaha2002 2 роки тому +3

    Minute soldering..lvlu😎😎

  • @sureykam8213
    @sureykam8213 2 роки тому +1

    👍