I'm 70+ years old and had not done a break pad repair in 40 years. This video helped me do it on the rear (pads only) in less than 1 1/2 hours. 2015 Honda civic. Thanks so much for doing this and to others I watched. This had the piston turn tip that I needed to use.
Great video! Quick add on: Using silicon paste will prevent the sliding pins from getting gunky. Grease dries up over time while silicon paste does not. Just a tip for anyone who has gone through this too many times.
Loosen the cap on your brake fluid reservoir under the hood. This makes it easier to compress the calipers. The brake fluid inside the calipers will travel back up the brake line without any resistance and makes compressing the caliper a lot easier.
I like it. Had been a long time since I did my own brakes. Times are tight so with some gloves, live resin, and my phone magnetically attached just above my wheel well. I proceeded to replace rear brakes without not even 1 minut issue. Thx! Good video. Oh.....don't hate on us "disruptive" truck drivers. If I was trying to make youtube vids I probably wouldn't do it next to a truck stop. 🙃
Thanks for the video!! Started trying to squeeze the piston in like the fronts, wasn't budging, then I remembered OH THAT VIDEO! My rear break pads were down to metal so I used the pad to put in the notch and turn. Problem solved. Saved that pad in the tool box for future uses.
Thanks my dude. First time replacing my brakes and now that I've done it, it's rather insulting that Goodyear wanted to charge me around $200 to do this (that's including parts but still).
At 3:05, the reason why the inside pad wore unevenly is because the pad did not slide on the upper and lower stainless steel shims. As you indicated, both sliding pins were free to move, so that is not the issue. The trouble is, nobody cleans the rust built-up under the stainless steel shims, so the pad does not slide easily. You yourself mentioned the pad was hard to remove.
At 8:20, the rotor retaining screw/bolts are what you use to thread into those holes to remove the rotor whilst gently tapping the edge of the rotor with a hammer.
You are doing good job seems you are saying not to use the two screw to hold the rotor back. Finally you did use it, thank you. If you do it in class you failed.
No, he is correct in his terminology. Silicon Grease is what is used in the factory as well as by Honda technitions for the caliper pins though I would have used M77 for the pad backing and "ears" but what he used is just fine.
@@aaronneason2531 premature on the lube comment but definitely think i few key steps were skipped. But like I said, one of the best videos I found for 2012 Honda civic brakes.
For the retaining screws, you can run them in with an everyday Phillips screwdriver because it air gotta be tight. Also, a small pry bar works well to roll the caliper piston back in.
i bought one at lowes, as i was in the middle of the job before i realized a phillips screw driver wasn't going to work. couldn't wait on amazon. the Kobalt impact driver worked but the bit was ruined after 4 screws. kobalt doesn't sell the bits separately that i know of.
Just a tip. The rear arm has a bolt on it to hold the hand brake line in place. That bolt is the correct thread to remove the disc.. same on the front aswell ( bralineline clamp on the strut). I've used the bolt to remove the discs without belting them.
Just a suggestion for removing the rotor screws. Do yourself a big favor, go to the auto store and buy a tube of valve grinding compound. Put that on the #3 philips impact bit. That will put more "bite" into turning the screw with the impact driver. Of course if you have a js3 bit, all the better, but I got mine out just fine with a ph3 bit. I put them back in with some antiseize, so it should be easier next time. The other thing is to put some antiseize around the rim where the rotor contacts the bearing hub. The last comment would be to head to the hardware store with a new rotor. Find the metric bolts that fit into the extractor holes. Buy 4 (2 for each side). Those extractor bolts make removing a rusty rotor so much easier. When done, I put the bolts into a pill bottle and labeled it rotor extractor bolts, ready for the next time now.
Well made video! Mine had more rust, so sprayed WD-40 on it to help get it apart. wonder why they dont paint these parts ? Seams like Rust-belt owner are going to have a issue here even after a few years. my 1996 Nissan Maxima had similar screw in caliper piston
GM uses screws on the rotors on a lot of their post 2006 vehicles. However they use various sizes of torx bits, not Phillips. Torx are much easier in my opinion. No impact needed. Even in the rust area of Minnesota where I used to live. You could probably just change them to a torx head screw of same size if you prefer to keep them.
I also just did mine and it’s almost impossible to see if it lines up. I put a thin film of silicone grease on the piston and I think as it starts to screw out with brake pressure, it will fall into proper place. Hopefully
Believe it or not, the reason many have trouble with the rotor mounting screws is that they are in fact not phillips head. They are actually JIS (Japanese Industrial Standard) head. It's only a minor difference in design, but it makes a world of difference. If you are stripping screws on a Japanese-engineered vehicle, this is probably why. I have one of these and it works like a charm. www.amazon.com/Vessel-125943-P3x150-Impacta-Screwdriver/dp/B003BGTTSE?th=1
I recently did the rear brakes on my civic and I knew about lining up the "button" with the caliper piston. But when I put it back together I for the life of me could not tell if it was lined up properly or not. Is there a trick?
My new trick is to tighten 2 lug nut each side of the small screw, so they push the rotor in, and relieve pressure from the screw. But make sure that the lug nuts are deep enough and that you do not damage the part that "seats" into the wheel.
The brake is released the whole time. The piston will slowly press back in so you can put the caliper back on. Once everything is installed then you can press the brake a few times to get the piston back to place
my dumbass friend didn't align the groove with the pimple on the brake pad (35:00) when he did my brake, which caused my brake fluid to leak. That costed me 500 bucks to replace. Also, evetime I press brake, it makes squeaky sound on the rear. Lesson learned. Do it on your own or take your car to a professional.
sir how are you, could you please help me ?, I need to change the rear bearing of a 2015 Honda Civic LX, you could guide me, or at least tell me that I have to loosen, thanks, please please
Every other video on UA-cam the person uses brake cleaner spray to clean the thin layer of oil on the rotors, both sides. I guess you forgot to mention that.
I can't overstate how obnoxious I find it that Honda made that weird "twist" caliper piston. Why can't they just use a regular c-clampable piston like every other manufacturer? Before I watched this video I thought it was just a regular piston, and I c-clamped it as I've done on many other cars. Well, my c-clamp broke and now I know why!
Baby brakes, so tiny. Try some spray brake cleaner and lube (anti seize) the edges that touch the clips for smooth movement of the pads. You can also hammer in a torx head to remove the 2 JIS screws.
This video was nearly a year ago, done in June, so I’d say they probably live somewhere like me, that uses road salt for winter, thus why they are fixing in June. You can’t even hear the warning scrape sometimes, because the windows are up all winter. Salt not only rusts parts, but our cars’ bodies rust out much more quickly than, say, California. There’s a reason why people seek out vehicles that lived in warmer climates.
Never just top off your brake fluid! The only time you should add brake fluid is after a brake pad replacement. Add your new pads and then add brake fluid fresh from a NEW bottle and then bleed your brakes making sure your fluid level is at max when you are finished. As your pads wear the level will lower in accordance with wear on the pads. If you have pristine pads but low fluid level either "A" you have a leak somewhere in your brake line or "B" when the new pads were installed the fluid level was not adjusted properly. Also as another side note if you do not adjust your fluid level eventually you will eventually drop too low and your closed system will pump air into the system leading to spongy ineffective brakes
Most new rotors have a spritzing of oil on the surface from the factory. …. You should spray both sides with brake cleaner and wipe with a clean rag before installing new rotors.
Break compressor tool does not work with Honda's. I tell you from my experience owning two that have the screw system. Just screw the cylinder back in and you are done.
I'm 70+ years old and had not done a break pad repair in 40 years. This video helped me do it on the rear (pads only) in less than 1 1/2 hours. 2015 Honda civic. Thanks so much for doing this and to others I watched. This had the piston turn tip that I needed to use.
Great video! Quick add on: Using silicon paste will prevent the sliding pins from getting gunky. Grease dries up over time while silicon paste does not. Just a tip for anyone who has gone through this too many times.
Also, clean the pins and bores! Use brake parts cleaner! Use fresh silicone paste.
Loosen the cap on your brake fluid reservoir under the hood. This makes it easier to compress the calipers. The brake fluid inside the calipers will travel back up the brake line without any resistance and makes compressing the caliper a lot easier.
Thanks for that tip. I haven't done this yet but that's good to know
*Only do this after the brakes are cool! You can get severe burns if you do this before they are cool!
Make a video on it and tagg me
I like it. Had been a long time since I did my own brakes. Times are tight so with some gloves, live resin, and my phone magnetically attached just above my wheel well. I proceeded to replace rear brakes without not even 1 minut issue. Thx! Good video. Oh.....don't hate on us "disruptive" truck drivers. If I was trying to make youtube vids I probably wouldn't do it next to a truck stop. 🙃
Thanks Man your video help me a lot. I Finally changed my 2013 civic si brakes for the first time...had 74k miles.
Thanks for the video!! Started trying to squeeze the piston in like the fronts, wasn't budging, then I remembered OH THAT VIDEO! My rear break pads were down to metal so I used the pad to put in the notch and turn. Problem solved. Saved that pad in the tool box for future uses.
Thanks my dude. First time replacing my brakes and now that I've done it, it's rather insulting that Goodyear wanted to charge me around $200 to do this (that's including parts but still).
At 3:05, the reason why the inside pad wore unevenly is because the pad did not slide on the upper and lower stainless steel shims. As you indicated, both sliding pins were free to move, so that is not the issue. The trouble is, nobody cleans the rust built-up under the stainless steel shims, so the pad does not slide easily. You yourself mentioned the pad was hard to remove.
At 8:20, the rotor retaining screw/bolts are what you use to thread into those holes to remove the rotor whilst gently tapping the edge of the rotor with a hammer.
I have this exact problem on my rear left going to fix it myself after I watch your video
Thanxalot! Great job im catching and showing the trouble spots. You helped immensely.
In
Excellent explanation of the step by step process. Doing my daughter's civic brakes this weekend. Thank you so much for the vid!
Thank you for the video, you did me a service, I used a chisel but you gave me the idea, guy at Autozone said clamps should work lol
I like your video. Very good for beginners and ones who want to learn.
You are doing good job seems you are saying not to use the two screw to hold the rotor back. Finally you did use it, thank you. If you do it in class you failed.
Lube not grease. No brake cleaner?
Still one of the most well done videos on changing brakes I've seen.
No, he is correct in his terminology. Silicon Grease is what is used in the factory as well as by Honda technitions for the caliper pins though I would have used M77 for the pad backing and "ears" but what he used is just fine.
@@aaronneason2531 premature on the lube comment but definitely think i few key steps were skipped. But like I said, one of the best videos I found for 2012 Honda civic brakes.
Thanks for the video. I didn't know about rotating the piston. I was trying to compress it with a C clamp like the front brakes. Helped me out a lot.
For the retaining screws, you can run them in with an everyday Phillips screwdriver because it air gotta be tight. Also, a small pry bar works well to roll the caliper piston back in.
i bought one at lowes, as i was in the middle of the job before i realized a phillips screw driver wasn't going to work. couldn't wait on amazon. the Kobalt impact driver worked but the bit was ruined after 4 screws. kobalt doesn't sell the bits separately that i know of.
58gennaro: That because it’s not a “Phillips.” It’s actually a “JIS” (Japanese Industrial Standard), similar shape but it is different.
Nice video ! Just be carefull not to damage the seal of the caliper with the metal plate!
The piston needs to be positioned like "+" so that the matching pin on the back of the brake pad lines up
Just a tip. The rear arm has a bolt on it to hold the hand brake line in place. That bolt is the correct thread to remove the disc.. same on the front aswell ( bralineline clamp on the strut). I've used the bolt to remove the discs without belting them.
A 3/8ths socket wrench head works to screw the piston back in. Just put it in the center of the cross of the piston and crank the wrench as normal.
I just use a BIG screwdriver to compress the calipers. Works great.
Just a suggestion for removing the rotor screws. Do yourself a big favor, go to the auto store and buy a tube of valve grinding compound. Put that on the #3 philips impact bit. That will put more "bite" into turning the screw with the impact driver. Of course if you have a js3 bit, all the better, but I got mine out just fine with a ph3 bit. I put them back in with some antiseize, so it should be easier next time. The other thing is to put some antiseize around the rim where the rotor contacts the bearing hub. The last comment would be to head to the hardware store with a new rotor. Find the metric bolts that fit into the extractor holes. Buy 4 (2 for each side). Those extractor bolts make removing a rusty rotor so much easier. When done, I put the bolts into a pill bottle and labeled it rotor extractor bolts, ready for the next time now.
Awesome video. Very detailed. 👍👍
Are the rotors & pads you had used the same for 2012 civic also ? Appreciate the great video & links for purchases.
Mike
Your video was very informative. Thank you.
Well made video! Mine had more rust, so sprayed WD-40 on it to help get it apart. wonder why they dont paint these parts ? Seams like Rust-belt owner are going to have a issue here even after a few years. my 1996 Nissan Maxima had similar screw in caliper piston
Hi what is a purpose of the pin on back of pad which goes in caliper screw?
Thanks for the video. How do you look to make sure one of the nubs is in the cross part of the piston?
GM uses screws on the rotors on a lot of their post 2006 vehicles. However they use various sizes of torx bits, not Phillips. Torx are much easier in my opinion. No impact needed. Even in the rust area of Minnesota where I used to live. You could probably just change them to a torx head screw of same size if you prefer to keep them.
LOL that truck at 12:40 needs brake work done bad! 😂
If you don't line the cross up on the piston with the nub on the pad do you know of hat can happen? I just did mine and I'm not sure it lined up
I also just did mine and it’s almost impossible to see if it lines up. I put a thin film of silicone grease on the piston and I think as it starts to screw out with brake pressure, it will fall into proper place. Hopefully
Thanks! Good video, trying this today!
Use a 3/4 socket wrench tip to turn the bit back in super easy and a impact drill makes life way easier then the screw driver.
Believe it or not, the reason many have trouble with the rotor mounting screws is that they are in fact not phillips head. They are actually JIS (Japanese Industrial Standard) head. It's only a minor difference in design, but it makes a world of difference. If you are stripping screws on a Japanese-engineered vehicle, this is probably why. I have one of these and it works like a charm.
www.amazon.com/Vessel-125943-P3x150-Impacta-Screwdriver/dp/B003BGTTSE?th=1
Very true, they are JIS, but they can still get rusted into place and still be a pain
@@JRobling Yes. I use an impact screwdriver. Having a heavy hammer is key.
Fun fact: you can use the squealer on the old pads for the notch tool.
Great video. What is the torque tightness of the 12mm bolt that holds the caliper? Thank you
I have 2015 Civic can you recommend rear rotors for it? Link in description says it won't fit for 2015.
Thanks, I used the video today
I recently did the rear brakes on my civic and I knew about lining up the "button" with the caliper piston. But when I put it back together I for the life of me could not tell if it was lined up properly or not. Is there a trick?
I just left the rotor screws off. Wasn't as easy as yours, so had to drill them out.
My new trick is to tighten 2 lug nut each side of the small screw, so they push the rotor in, and relieve pressure from the screw. But make sure that the lug nuts are deep enough and that you do not damage the part that "seats" into the wheel.
great video! I have a question if you release the brake before you turned the piston?
The brake is released the whole time. The piston will slowly press back in so you can put the caliper back on. Once everything is installed then you can press the brake a few times to get the piston back to place
This helped me. Thank you.
Pad Slider grease?
Do I have to bleed the brakes after I'm done replacing them?
You only need to bleed the brakes if you replace the brake lines or calipers
Car needs to be in neutral when replacing rear brakes? Is it the same for front brakes?
The car needs to have the ebrake off when replacing the rear brakes, not in neutral, it would roll away. Front brakes doesn't matter
Note from factory* if the replacement brakes have the shim already attached they say no brake quite or any other products on the pads.
My brake fluid bolt won’t come off …
Thanks for the video!
Nice job. Thanks!
Use a pry bar to turn in the caliper piston
Great video, thanks for sharing.
I seen on another UA-cam channel someone used a flat head screwdriver on an angle to turn the cylinder.
my dumbass friend didn't align the groove with the pimple on the brake pad (35:00) when he did my brake, which caused my brake fluid to leak. That costed me 500 bucks to replace. Also, evetime I press brake, it makes squeaky sound on the rear. Lesson learned. Do it on your own or take your car to a professional.
sir how are you, could you please help me ?, I need to change the rear bearing of a 2015 Honda Civic LX, you could guide me, or at least tell me that I have to loosen, thanks, please please
Has anyone driven a 9th gen civic without the rear discs and with rear discs. Lx vs ex. - just curious if there’s a noticeable difference
Thanks man good video
Every other video on UA-cam the person uses brake cleaner spray to clean the thin layer of oil on the rotors, both sides. I guess you forgot to mention that.
I just used a putty knife to turn my rotor back in.
I can't overstate how obnoxious I find it that Honda made that weird "twist" caliper piston. Why can't they just use a regular c-clampable piston like every other manufacturer? Before I watched this video I thought it was just a regular piston, and I c-clamped it as I've done on many other cars. Well, my c-clamp broke and now I know why!
Ur the man
I didn't realize my tool not only uses screw driver bits but also sockets. Shityou do learn something new sometimes. Lol
#1 flat head screwdriver for turning in the caliper back in. Lol
Very helpful thank you
Baby brakes, so tiny.
Try some spray brake cleaner and lube (anti seize) the edges that touch the clips for smooth movement of the pads.
You can also hammer in a torx head to remove the 2 JIS screws.
thats a lot of rust for only 5 years, where do you live ??
This video was nearly a year ago, done in June, so I’d say they probably live somewhere like me, that uses road salt for winter, thus why they are fixing in June. You can’t even hear the warning scrape sometimes, because the windows are up all winter. Salt not only rusts parts, but our cars’ bodies rust out much more quickly than, say, California. There’s a reason why people seek out vehicles that lived in warmer climates.
GM has a screw in the rotor too.
I have a 2012 civic ex and the back bolt not a 12mm.
Thank you!!
💪
You should never have to top off your brake fluid
Unless brake fluid is lost when a new caliper is installed. That's not the case in this video though.
You don't take the top off just unscrew the top to relieve pressure to get the caliper piston back in
Never just top off your brake fluid! The only time you should add brake fluid is after a brake pad replacement. Add your new pads and then add brake fluid fresh from a NEW bottle and then bleed your brakes making sure your fluid level is at max when you are finished. As your pads wear the level will lower in accordance with wear on the pads. If you have pristine pads but low fluid level either "A" you have a leak somewhere in your brake line or "B" when the new pads were installed the fluid level was not adjusted properly. Also as another side note if you do not adjust your fluid level eventually you will eventually drop too low and your closed system will pump air into the system leading to spongy ineffective brakes
Most new rotors have a spritzing of oil on the surface from the factory. …. You should spray both sides with brake cleaner and wipe with a clean rag before installing new rotors.
nice car
You can rent a brake compressor tool for free from auto zone
Break compressor tool does not work with Honda's. I tell you from my experience owning two that have the screw system. Just screw the cylinder back in and you are done.
silicone on pins no grease very important grease hardins up like glue
That a boy try and try
👍🇸🇪
Thank you for your tutorial. It was helpful.
great DIY vid!! TY!
Great video thanks