Mistake I made was cross threading one bolt on handlebar mounting bracket, so be very careful to hard start and lightly turn each four bolts - may need help with additional person holding handlebar in place to keep bracket from going crooked and causing a bolt to angle.
After repairing the thread I decided to leave the bracket off the stem and put it around the handlebar directly instead to be safe. There’s enough slack in wiring to just slide the handlebars over the stem with the bracket already cliched onto them. Going for my first ride now!
Turn bike off remove battery and reinstall and turn on bike. If code does not clear disconnect motor wire harness to controller (connector on right side of rear wheel and then reconnect firmly… turn on bike. If error code persists then contact Tamobyke for new motor
We got ours and had to do the same thing, all of the cables came undone when we tried to put the handle bar on, took it all apart and moved the cable, looking at the front WHY did they NOT run it through the hole below the handlebars. Thanks so much for the video, the directions are horrible!
No. Doubt directional can display on screen as the wires do not interact with controller. turn signal switch wired to rear taillight and do not go thru controller
@@BRichSolution and I’ve seen those pronged connector key starters on Amazon but they were 3 prong. Any tips on what I would do to wire a key starter onto the v20 without too much hassle ( adapters, switches and such)
Ridstar is faster and motor is torquer than Tamobyke v20. Make sure to 20ah 1500w version of Ridstar Q20 the 15Ah version is not worth the $100 savings
I'm not sure why, but whenever I attempt to configure P 06, I encounter an E20 error on the screen. Additionally, P03 doesn't seem to save even when I press + and - together. Can you help me? Do you have any advice? 😢
E20 is trotthle error *Drive Mode setting. This setting could come in very handy. This P setting allows you to turn off the throttle completely. 00 = driven by PAS. The throttle is useless at this time. Use this option if you just want pedal assist and NO throttle. 01 = driven by Throttle. PAS is useless at this time. If you do not need PAS, then use this option. 02 = driven by both PAS & Throttle. The throttle is useless at Zero Start status. Both throttle and Pedal Assit are active.*
@@BRichSolution the instruction booklet I received were tiny black & white photos & useless. Not at all the booklet you held in your video, but u were to the point & a quick well instructed video. Thanks it helped a lot!
Thanks for the video, but you go so fast and with your hand in the way couldn't see what you were doing part of the time. Did help some so again thanks.
Thank you so much for this video, you really helped me with putting the bike together!
Congrats on new bike and glad video helped you out
Yes seeing someone explain and perform bike assembly is great compared to the terrible assembly instructions.
My new V20 has a different goose neck. I had to reroute the wires also.
Ok
A good bike, but there are no right and left turn signals on the front of the bike ☹️
You can always add the front turn signals or go wireless
ua-cam.com/video/9cmqX0u-3s4/v-deo.htmlsi=mS-t_4UEkFCdIRrA
So bloody what
Mistake I made was cross threading one bolt on handlebar mounting bracket, so be very careful to hard start and lightly turn each four bolts - may need help with additional person holding handlebar in place to keep bracket from going crooked and causing a bolt to angle.
good feedback
After repairing the thread I decided to leave the bracket off the stem and put it around the handlebar directly instead to be safe. There’s enough slack in wiring to just slide the handlebars over the stem with the bracket already cliched onto them. Going for my first ride now!
Have you ever came across an error code “20” and if so what was your solution to clear it?
Turn bike off remove battery and reinstall and turn on bike. If code does not clear disconnect motor wire harness to controller (connector on right side of rear wheel and then reconnect firmly… turn on bike. If error code persists then contact Tamobyke for new motor
@@BRichSolution thanks so much, it works 👍🏽
Would you think it’s good to get ridstar q20 over this?
Yes, Ridstar Q20 is faster and has better range, buy make sure to buy 20Ah version, the 15Ah version is not worth buying
We got ours and had to do the same thing, all of the cables came undone when we tried to put the handle bar on, took it all apart and moved the cable, looking at the front WHY did they NOT run it through the hole below the handlebars. Thanks so much for the video, the directions are horrible!
I agree and informed them to change
I just got mine and love it. People are alway stopping me to ask about it. For some reason it wont let me turn off cruise control.
Change setting p07 to 1 and cruise control is off
Do you know how to activate all the functions that are shown on the screen when you turn it on, such as the direction lights, etc., thank you
No. Doubt directional can display on screen as the wires do not interact with controller. turn signal switch wired to rear taillight and do not go thru controller
How many miles can it go
25 miles on throttle only top speed. Pedal or lower speed 40 miles. You can add extra battery to go farther ua-cam.com/video/p_Spml-tukk/v-deo.html
Btw what you did with p03 you have to put in a code to unlock that speed stuf but the code is most of the time 1111 so you didnt change the speed
I left mine as default it never had a code or password
@@BRichSolution ooh ok
can the headlight be mounted higher ?
Yes the headlight can be moved up the fork
@@BRichSolution ty just got one can’t wait for it to be delivered. oh and is it easy to remove the decal/sticker on the battery? any other heads up ?
Does it go faster than the ouxi v8 and is the back suspension worth it and can you do wheelies on it?
About the same. Amyet g60 goes faster than Ouxi v8 amzn.to/3SzU9D7
Ik its been a long time, but can I take out the grips abs swap them up with customs ones? Same with the pedals
Yes you swap grips and pedals are standard sizes
can you put the handlebars higher i have an ouxi v20 pro but im 2 meters tall and i keep accidently hitting the beeper when im biking
Yes change handlebars to taller handlebars or taller stem risers
Almost gonna get mine
Good choice
What kind of pins do the front screen use? I’m trying to wire a key start
5 pin green Juliet connector. Male prong connector from
Screen
@@BRichSolution and I’ve seen those pronged connector key starters on Amazon but they were 3 prong. Any tips on what I would do to wire a key starter onto the v20 without too much hassle ( adapters, switches and such)
Hey friend I got mine but I need new disc brakes do you know the size?
B03 pads work see link amzn.to/4cvenFM
How to fix the back wheel flat tube
Buy a 20x4” tube amzn.to/3Kl8v5r and watch this video on how ua-cam.com/video/FNVKIOSWuAE/v-deo.htmlsi=DUZHkozjmItdiKwQ or ask bike shop to change it
Good vidéo 🎉
Thanks
I have a question my bike is stuck on gear 3 speed and I can’t get to go faster. How can I fix this?
Ask seller how to unlock
Did you ever figure it out?? Sorry I'm having same problem and apparently this "Expert😢 " has no clue
Hey! I love all your videos. If you had to choose, would you go with the Ridstar Q20 ($903) or the Tamobyke V20 ($717). Thanks!
Ridstar is faster and motor is torquer than Tamobyke v20. Make sure to 20ah 1500w version of Ridstar Q20 the 15Ah version is not worth the $100 savings
I'm not sure why, but whenever I attempt to configure P 06, I encounter an E20 error on the screen. Additionally, P03 doesn't seem to save even when I press + and - together. Can you help me? Do you have any advice? 😢
Not sure why those settings are restricted. Ask seller why
Its a code menu the factory code is always 1111 then u get change the settings of P03 00 is MAX 3 modes ansd if u put P03 01 it has 5 modes
it always restricted
@@BRichSolution
E20 is trotthle error *Drive Mode setting. This setting could come in very handy. This P setting allows you to turn off the throttle completely.
00 = driven by PAS. The throttle is useless at this time. Use this option if you just want pedal assist and NO throttle.
01 = driven by Throttle. PAS is useless at this time. If you do not need PAS, then use this option.
02 = driven by both PAS & Throttle. The throttle is useless at Zero Start status. Both throttle and Pedal Assit are active.*
ok
P03 doesn’t save and his on video starts at power mod 5 can someone help me ?
email tamobyke at qingmaifactory@163.com for help and post results
3:00
Thanks
Do I have to take my battery off my bike while charging it ???
No you can charge on the bike
How many amps was that charger, guessing 2 or 3.
It's a 54V 2Amp charger.
3A
Any way to lower the height an inch or so?
Shorter 165mm rear shock. See video and link in video
ua-cam.com/video/PZsDZJlQuGE/v-deo.html
Thank you!! @@BRichSolution
P04 is not working for me, it always get's to 45 km per hour
Yes 45km/h is limit. I am working on solution to go faster will post video in a week
I don't want to go faster, I want to stop my engine at the speed, set in P04. @@BRichSolution
Great well done video!
Thank you very much!
@@BRichSolution the instruction booklet I received were tiny black & white photos & useless. Not at all the booklet you held in your video, but u were to the point & a quick well instructed video. Thanks it helped a lot!
We’re can I order this bike from ??
Amazon amzn.to/3GCRt0K
How to save P03 setting?
Change the setting then hold + and - buttons
@@BRichSolution I've tried but it doesn't work (
@@BRichSolution also P02 doesn't work
@@easy_money_sniper04same have you solved it yet
Same here, did you get it?
Thanks for the video, but you go so fast and with your hand in the way couldn't see what you were doing part of the time. Did help some so again thanks.
Okay will slow down next bike
this help thanks!
Glad it helped!
what does *self starting* do on p05 @@BRichSolution
Not in Australia.
Not on aliexpress?