Thank-you for blazing the trail with this phone. There's almost no repair info to be found online, but thanks to your video I was able to successfully replace the charge port on my Moto Hyper One. The original adhesive was enough to get the back plate back on the phone.
I fucked up and broke one of the cables that you remove at 3:46, is there a name for this type of cable/connector and is it possible to replace it? the phone turns on and functions without it, but the bottom right corner of the screen doesn't register touches anymore.
Here is a link, they aren't for your model phone but should still work if the lengths match. Not sure what lengths they are exactly etc. (they are called coaxial antenna cables) www.mobiledefenders.com/catalogsearch/result/?cat=0&q=coax
No you would need to disassemble it so you can disconnect the screen cable and be able to pry the old screen off and run the new screen cable and re attach it to the main board.
could you tell me how to fix the dolby audio issue. My speakers are not working because my phone has disabled the dolby audio because it believes that the headphone jack is connected but it isnt. Is there any way i can get this fixed?
You would have to somehow remove whatever is stuck in the headphone jack making it think something is plugged in, or have a professional place solder off the jack and install a new headphone jack.
@PBKreviews: In your experience, how long after a Motorola phone is released do replacement screens begin to be available for purchase? Motorola wants more than half the cost of the phone to replace it for me...
Once you take the phone apart and disconnect the screen cable etc., all that is left is to heat the front of the phone where the screen is with a hair dryer or heat gun to loosen the adhesive and pry the screen off. Then you apply new adhesive, or if your screen comes with pre installed adhesive you don't need to do that, and run your new screen cable back through the slit in the midframe, re-apply your screen to the frame and re-assemble the phone. I don't have the phone with me anymore.
Most likely no, because very rarely are batteries the same size to fit the space the specific phone has for the battery and also very rarely are the connectors the same or located at the same position so your cable would reach to connect to the board. Even if the space is there, the connector is the same, you also sometimes have software that might not read the battery chip correctly and give you issues like a battery icon with a "!" or not allow to power on etc. Now say in circumstances that a phone is the same exact model just a higher end version say a S10 or a S10+, the battery connector might be the same, the phone software might read the battery chip correctly however the space and position of the battery might be different and make it hard to fit or work with. The only phone to my knowledge that was able to be used with a upgraded battery with no problems was the droid razr and droid razr maxx where the body and build of the phone was exactly the same aside from the slimmer battery and back of the razr compared to the razr maxx. This allowed you to upgrade the razr with the larger razr maxx battery and only need to slightly modify the back plate to seat in place with the larger battery.
@@PBKreviews thanks sir. BUT i am pakistan hear is not popular motorola buy i love motorola .hear is not available this model battery . i dont know who model use battery this motorola
Trying to fix a broken screen - I can get the screen loose easy enough but cant work out the back panel - how do you pry it off - Ive heated the back but cant get the plastic tool into any gap? Anyone help? Thanks!
Hi, you can try using a suction cup to help pull up a bit to give you some leverage or if you don't have one, a thin razor or something (even though that may scrape or scuff your housing)
@@conceptbuildingsolutionsde6707 There is only one seem or line separation between the back panel and the frame, so should be only one place you can pry the back plate off or put your pry tool in between.
lol some like it some don't I guess depends on each persons needs from their devices. It personally would not be my primary choice either but that's just because I usually tend to go for the higher end devices.
Thank god you exist! efing best (only) full tear down video of this phone!
:) Glad it was helpful
Thank-you for blazing the trail with this phone. There's almost no repair info to be found online, but thanks to your video I was able to successfully replace the charge port on my Moto Hyper One. The original adhesive was enough to get the back plate back on the phone.
You're welcome. If you need any new adhesive down the line, you can check mobiledefenders.com usually they carry most parts.
Yeah my vibration motor broke
Parabéns pelo vídeo. Brasil
Thank you!
I fucked up and broke one of the cables that you remove at 3:46, is there a name for this type of cable/connector and is it possible to replace it? the phone turns on and functions without it, but the bottom right corner of the screen doesn't register touches anymore.
Here is a link, they aren't for your model phone but should still work if the lengths match. Not sure what lengths they are exactly etc. (they are called coaxial antenna cables) www.mobiledefenders.com/catalogsearch/result/?cat=0&q=coax
Great presentation skills and professionalism. Thank you for sharing.
Thanks!
Woow nice tear down video 🤩
Thank you
@@PBKreviews wait for next Motorola device teardown video
Do you know where to purchase a replacement screen from?
I have the same question!
Yes, I can't find any stores that sell them!
@@vide0fiend You can find replacement screens on Amazon and AliExpress (limited availability) now
Is there any video of it's front camera repairs? Camera came out sometimes, sometimes doesn't. Awaiting your reply. Thanks
Well this video shows how to take it apart to replace it. Might be a bad motor on the unit and might need to be replaced.
Do you know if the power/volume switch circuit is glued in place, seems to me like I need to apply heat to remove it.
Yes there is some adhesive holding the flex cable in place.
Do I have to do all this to just replace a cracked screen or can I pop the screen off from the front somehow?
No you would need to disassemble it so you can disconnect the screen cable and be able to pry the old screen off and run the new screen cable and re attach it to the main board.
could you tell me how to fix the dolby audio issue. My speakers are not working because my phone has disabled the dolby audio because it believes that the headphone jack is connected but it isnt. Is there any way i can get this fixed?
You would have to somehow remove whatever is stuck in the headphone jack making it think something is plugged in, or have a professional place solder off the jack and install a new headphone jack.
Thank you so much bro!
No problem!
Does anyone know were to get a replacement screen for this model?
Looks like there arn't replacement screens for this available yet, your best bet might be to contact motorola for their repair service.
@@PBKreviews ty good sir
@PBKreviews: In your experience, how long after a Motorola phone is released do replacement screens begin to be available for purchase? Motorola wants more than half the cost of the phone to replace it for me...
Would it be possible to replace the headphone jack?
It's possible but requires solder work since its soldered onto the main board
how is he ever going to put that phone back together?
Donde compraste la pantalla ?
amzn.to/3g0tKZj here is the link for one on amazon
Can you do a video of how to change the screen that would be great thanks
Once you take the phone apart and disconnect the screen cable etc., all that is left is to heat the front of the phone where the screen is with a hair dryer or heat gun to loosen the adhesive and pry the screen off. Then you apply new adhesive, or if your screen comes with pre installed adhesive you don't need to do that, and run your new screen cable back through the slit in the midframe, re-apply your screen to the frame and re-assemble the phone. I don't have the phone with me anymore.
Sir lhave motorola droid maxx xt1080 can i use other motorola madel battery because xt 1080 battery not available
Most likely no, because very rarely are batteries the same size to fit the space the specific phone has for the battery and also very rarely are the connectors the same or located at the same position so your cable would reach to connect to the board. Even if the space is there, the connector is the same, you also sometimes have software that might not read the battery chip correctly and give you issues like a battery icon with a "!" or not allow to power on etc. Now say in circumstances that a phone is the same exact model just a higher end version say a S10 or a S10+, the battery connector might be the same, the phone software might read the battery chip correctly however the space and position of the battery might be different and make it hard to fit or work with. The only phone to my knowledge that was able to be used with a upgraded battery with no problems was the droid razr and droid razr maxx where the body and build of the phone was exactly the same aside from the slimmer battery and back of the razr compared to the razr maxx. This allowed you to upgrade the razr with the larger razr maxx battery and only need to slightly modify the back plate to seat in place with the larger battery.
@@PBKreviews thanks sir. BUT i am pakistan hear is not popular motorola buy i love motorola .hear is not available this model battery . i dont know who model use battery this motorola
@@PBKreviews thanks sir
@@zeehot1598 your welcome. You can always try searching online to purchase the battery you need
Trying to fix a broken screen - I can get the screen loose easy enough but cant work out the back panel - how do you pry it off - Ive heated the back but cant get the plastic tool into any gap? Anyone help? Thanks!
Hi, you can try using a suction cup to help pull up a bit to give you some leverage or if you don't have one, a thin razor or something (even though that may scrape or scuff your housing)
@@PBKreviews Thank you for your reply - Ill try that - I presume Im working on the join between the black plastic edging and the coloured base.
@@conceptbuildingsolutionsde6707 There is only one seem or line separation between the back panel and the frame, so should be only one place you can pry the back plate off or put your pry tool in between.
I am so happy Motorolla does not make cars
how to replace / unmount battery missing ;-)
Mine says it's charging but the battery isn't increasing. It's dead now and I can't figure out how to fix it. It won't charge.
It might be a bad battery or bad charger port. You would need to replace one or the other and see which is the issue.
Cool
Motorola one action pls 🇨🇴 saludos desde Colombia
Hi, already done the One Action, check my videos you will see it :)
I have this cell phone: it sucks.
lol some like it some don't I guess depends on each persons needs from their devices. It personally would not be my primary choice either but that's just because I usually tend to go for the higher end devices.