Quick DIY fix for my broken metal vise
Вставка
- Опубліковано 1 кві 2020
- My cast iron metal vise broke up. Due to corona virus lockdown I couldn't just go out to buy a new one. So I tried to temporarily fix it with the tools I already had in my shop. Basically a stick welder and an angle grinder. Hopefully it will last for a while if I treat it gently!
Tools and materials:
Stick welder: amzn.to/2JdljLs
Air Pneumatic rotary tool: amzn.to/2R4r6HB
Double Cut Carbide Rotary Burr Set: amzn.to/2UWYukV
Angle grinder: amzn.to/2E6uLAx
Flap Sanding Disc: amzn.to/3dLDWV6
Air compressor, nail and staple gun kit: amzn.to/2NMPCIH
Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.
You can also support my channel by getting a T-shirt: tinyurl.com/y87hcuuj
For more information about this project, go here:
tinyurl.com/rbokkyn
----------------------------------------------------------------------------
You can support my channel through Patreon:
/ scrapwoodcity
----------------------------------------------------------------------------
For more scrap wood projects, please visit my blog:
scrapwoodcity.blogspot.gr/
My social media channels:
Facebook
/ scrapwoodcity
Pinterest
/ scrapwoodcity
Instagram
/ scrapwoodcity
twitter
/ scrap_wood_city
#DIY #metalworking
![ЛЕБЕДЕВ у ДУДЯ: муху не обманешь 😁 [Пародия]](http://i.ytimg.com/vi/E74h5fvVrqs/mqdefault.jpg)
At first I thought you said 'my vice broke due to the coronavirus'! I thought only people could catch it!
lol
It's a new mutation, thought to have originated in a Wuhan metallurgical shop.
Hi SWC, 'Not to lecture here', but a little knowledge shared from my UA-cam learnings:- Cast iron /steel must be pre heated prior to welding, - then controlled (slowed) cooling immediately following to ensure success. I imagine that Pre heating of both components (at the site of the break) may be achieved with a blowtorch and then cooling given nicely a preheated forge (Switched off, then sealed off with the repaired component inside). I claim to be no scientist here, but I have a 'Thing' for Vices.
Like they say, "a grinder and paint make a welder what he ain't"
Good job and keep up the great work!
lol. Good point.
Try to preheat the part. And after welding, hitting it carefully with da hammer, to remove tension in the weld.
Thanks, I will try it out next time. :)
@@ScrapwoodCity Yes, that's good advice. Cast metal is notoriously difficult to weld and your first attempt was actually a very good effort. Pre-heating for annealing may give you a better result. I think the Post Apocalyptic Inventor has a vid doing just this. I'll look for it.
I was going to comment the same, preheat the piece
That weld was just like my junior prom night, NO PENETRATION! Cast metals are very hard to weld.
Lol
If you've got access to some metal plate and drilling and threading capabilities you could put a plate on each side across the weld. It appears you have room.
Yes, I think that's an option as well!
You have upgraded your channel from Scrap Wood City to scrap metal too!
I have a couple of metal working videos because they include interesting techniques. And also, you have to be able to make metal tools in order to manipulate wood. But my main thing still is woodworking! :)
Pas facile !!!! Joli travail bravo à bientôt salut Jeannot 🛠😉
thank you
The main thing is that you fixed it 💪
Indeed
Well done
Good job. Stay healthy!
Thank you
Some Grade 8 case-hardened bolts and two square chunks of steel plate, holes drilled through one plate, through the vise and through the other plate, on each side of the break, could work as a somewhat ugly 'splint'. Kind of like 'sistering' a weak or cracked floor joist by nailing another board alongside it.
Well it seems your second attempt proved to do the job. 👌🏽
Good work, mate.👍🏽
Take care, stay safe and be well.
Thanks. I hope so.
Did the same thing to my 7 inch vise . So I wanted to test my AMATEUR skills and did a little research . I ended up buying these expensive rods , and they worked really good . They were almost $50.00 with shipping for only 3 rods . I could have put that to a new vise 🙃, but I wanted to try and fix it myself . Oh , and I didn't have to preheat it either . Here are the Rods I used 99% Nickel Cast Iron Electrode made from the highest quality nickel available. 1/8 in. 3 PK | Job Pack $29.3 1 $29.30 plus $15.95 for shipping Total $45.25 The hardest part was putting that spring and C clip back on .
Nice
It works... As long as you don't put too much force (as you say), it should last. 😎
I hope so
I would have soldered wire cloth between layers of lead or tin after beveling the edges or cleaning around the crack.
Kind of how panel beaters used to restore car bodies before polyester putty came.
Alternatively, you could also epoxy wire cloth over the crack after beveling or boring through it.
Duct tape might be a good option if the weld breaks again.
lol, thanks
@@ScrapwoodCity goose tape is stronger though
Well done bro, no one in here is a pro anyway hahaha Here in Bs As, Arg. we are in same situation by this freakin virus, stay safe my friend! 👊
Thank you my friend
Good job ! You can save money too.
Thanks
LOL, i saw how you were repairing this and i didnt think it would hold. Im not sure if you have the correct welding rod or not but you need rod for cast iron and then you need to preheat the area to be welded. Im sure you know this by now though
I had a cast iron electrode but I couldn't pre-heat it properly ( I just had a torch). After a while I found a better solution, I actually used a copper brazing rod and brazed it. This worked much better!
Hmm, That won t last very long , and will be only suitable for light work like you show us at the video end.
Good job! I have the same problem with my cast iron vise. Cracked in the same location. Did you have to preheat your parts before welding?
Yes you have to heat them up first
if it doesnt have sentimental value, id say just toss it and buy a new one. that one will probably break again when your in the middle of something important, on a Sunday when stores are closed, or in a blizzard and cant go anywhere
Ωραία πρόχειρη λύση !!
Ευχαριστώ
Ωραίος!!!!!
Ευχαριστώ Σάκη
Thanks for this video, I broke my vise today and need to do this…..
I would suggest that you use brazing. Works much better
@@ScrapwoodCity Hi there,I only have a welder so I’ll have to make do, but did yours last a bit???
Yes it did. As long as you pre heat the piece and use special electrodes for cast iron
@@ScrapwoodCity I’ve got the right sticks for the job, and you suggest I heat the broken bits up??, only way to do this is to put them in some fire??? Thanks for the info, I’ve got nothing to lose trying that….cheers
You can use a blow torch
Busy bee is open! Princess auto is open! Yard sales are open even scrapyards are open!!!
I think it will not last long. Cast iron does not weld with the electrode.
I think so too. It can be welded with a special electrode, but still it's not the best thing!
Δεν είμαι ειδικός ούτε εγώ αλλά νομίζω πως δεν κολλάει έτσι το μαντεμι. Μόνιμα τουλάχιστον... Ευχαριστούμε για το βίντεο ωστόσο και καλή συνέχεια με τις υπόλοιπες κατασκευές!
Ευχαριστώ! Ναι νομίζω δεν είναι η σωστότερη διαδικασία. Ελπίζω να με βγάλει μέχρι να ανοίξουν τα μαγαζιά!
electrode type?
GooD)))))))
thanks
Did you heat up the cast iron before welding it?
I did, but not as much needed. You need strong fire like a big torch or oxygen, but I only have my propane torch. You indeed have to heat it well and uniformly at first!
did you weld the inside too?
No, I didn't
@@ScrapwoodCity that would make it even stronger
What type rod did you use?
I heard there's special rods for cast iron, but ppl say stainless rods doin good as well. Pre-heating needed and no warranty of course.
Need to pre heat it
its better to heat metal properly then make welding may avoid crack.good luck.
Damn just use the grinder or dy grinder disk
Braze it
Where in the world do you live that you can't buy a vice ??Home Depot, Lowe's, Ace Hardware, Harbor Freight they're all open so is Amazon
Well I live in Greece, and we are at lock-down at the moment. I could order one online but a vise is something I want to see live before I buy it!
@@ScrapwoodCity well that explains it