Nice work! As a few others have said, it is clever to use PVC that way - it's cheap and super easy to work with for many projects. Next time I make a kayak or a hot tub, I'll try out the ideas you've shown in your build. Thanks for going the extra mile to make a video. Very inspiring! PS - I think the colors you picked are perfect.
Three thoughts: 1) great work! 2) "plastic" is fine by me... remember that a generation of America's Cup finerglass boats were called "plastic fantastic". 3) I was hoping to see more time shaping the bow and stern... although this is mostly aesthetic, it would have taken the boat to another level. Guessing that sandpaper was out of scope...
Great video and build. Two things I would like to add for the next build: 1) Remove margarine (as I have for more than 20 years) from your kitchen and use it to make canoes. Use butter or any other natural ingredient to fry your food. Not Margarine, which does not have similarities with 'plastic'. 2) 3.57 / 8:04 When working with resin or cutting cured fiberglass, put a mask on. Preferably one with active coal. This shit is toxic in the long run, and you only have two lungs. Fiberglass will not be expunged from your body and remain there.
Saran pakai masker bg, debu resin itu sangat berbahaya dan berat. Sekali masuk paru2, selamanya akan tetap berada di dalam paru2. Yaa emang kalo mati si udah ajal yah, tapi apa ga kesian sama anak istrinya ntar ? blom tua udah sakit2an dan kurang produktif buat nyari nafkah. Perahunya luar biasa, pasti ringan dan awet.
Very nice! It did surprise me that you didn't use a scale to weigh the amount of epoxy and hardener. (The epoxy that is for sale where I live needs to be in the exact amount. Too much hardener and the epoxy becomes too brittle, too little hardener and it will remain sticky.)
2:57 I'm pretty sure that is not epoxy , but polyester, and MEK hardener. For lay-up work like this it's almost as good as epoxy, but epoxy cost double the price. The ratio hardener to resin is more important for the "open time" then for the strength of the finished product. Too much MEK hardener and you have only very short time to lay-up the fiberglass. Specially in the tropics.
That was Polyester Resin, I can smell it from here. I use epoxy for some things, and polyester for others. For a general purpose, knock-around boat, I'd use polyester every time. Far, FAR less expensive, and the weight difference on that project would only be a couple of kilos at most
If you take a piece of thick wire and bend it into a shape like a paint roller the put on the roller part two different size washers go large small large small etc… then bend the end of the roller to stop the washers from falling off but can roll ezy without much wiggle room then use it to roll the glass after wetting it thoroughly with resin the roller is better to get out air pockets and even out the resin saturation
OK, so share a link with all of us showing your canoe built from scratch, done the "right" way - and do it as inexpensively as he did. Oh, and don't forget to weigh it. And until we see a follow up video where his canoe is swamped, cracked, or otherwise made useless, I'd say he did everything sufficiently correctly to meet the basic requirements of form and function.
It is chopped strand mat (CSM), comes in various "weights" from 150-600g/m^2 and polyester resin and catalyst (1-2% depending on ambient temp). Needs to be measured!!! You should also finish with a layer of woven fibreglass roving (fabric). And you should use a hard ridged roller to saturate the fibres, not a soft brush to stipple. That way uses far more resin, and leads to far weaker fibres.
So much wrong with this. Why not make it in one piece for starters? No gel coat, no multiple layers, no measuring out resin and catalyst, no roller to maximize fibre saturation. This is NOT how you build fibreglass boats. I've built dozens of glass fibre kayaks. You fair and polish the plug (here the original boat), take a mold off the wooden plug, then build the final kayak in the mold. The laminate needs to be built up in one continuous process to achieve a chemical bond. Using margarine as a release agent will contaminate the surface and lead to delamination of the subsequent layers. Use wax, and polish it.
very minimalist has glassfiber, rules have how long boat have etc, 4 meter need 4 level glassfiber to boat ewerywere. and this have minimi what need do, normal need 5-7 level glassfiber 4 meter long boat. then have normal strong boat. big boat etc, 30 feet sailboat need 1 inc glassfiber mean 30-40 level glassfiber all boat. or 20 levell under then honeycomp and then 10 level, save little glassfiber about 1/4
I got about half way through this before I felt sorry for people living in 3rd world countries and how they had to build things with inferior materials. Then, I realized, this is posted on UA-cam. This person has access to the entirety of human knowledge. Original boat leaked. Why not use polyester resin and fiberglass to seal the original boat?....No clicks, No views. Instead, lets use the original boat to make a new boat, without watching other videos on boat building. I admit, you got me with the clickbait. Good job. Hope you do well on UA-cam, but I won't be watching any more of your videos. You fooled me once...
Nice work! As a few others have said, it is clever to use PVC that way - it's cheap and super easy to work with for many projects. Next time I make a kayak or a hot tub, I'll try out the ideas you've shown in your build.
Thanks for going the extra mile to make a video. Very inspiring!
PS - I think the colors you picked are perfect.
I've made a few surfboards so I understand glasswork. Great idea using pvc to give structure. Awesome job man.
At the end, he paddled it effortlessly, and quickly. Notice the leaves moving toward him. He was paddling against the current. Good job.
Three thoughts:
1) great work!
2) "plastic" is fine by me... remember that a generation of America's Cup finerglass boats were called "plastic fantastic".
3) I was hoping to see more time shaping the bow and stern... although this is mostly aesthetic, it would have taken the boat to another level. Guessing that sandpaper was out of scope...
Great video and build. Two things I would like to add for the next build:
1) Remove margarine (as I have for more than 20 years) from your kitchen and use it to make canoes. Use butter or any other natural ingredient to fry your food. Not Margarine, which does not have similarities with 'plastic'.
2) 3.57 / 8:04 When working with resin or cutting cured fiberglass, put a mask on. Preferably one with active coal. This shit is toxic in the long run, and you only have two lungs. Fiberglass will not be expunged from your body and remain there.
i loved to watch, building your canoe. Great work, thanks for sharing👍🏼👍🏼👍🏼👍🏼
You did a fantastic job. I really like this little boat
Best use for margarine that ive ever seen😅
ha ha ha
Trabalho com fibra de vidro há mais de 50 anos e nunca tinha visto usar margarina como desmoldante. Vou experimentar ainda hoje. Vivendo e aprendendo.
@@fernandooliveira-ex1xs Crisco or pig lard work good too and are cheap. :)
My grandfather told me 'every place you go, you find smart people'. He was right.
Waduhh bang pake masker pas motong fibernya... Bahaya debunya
Please wear a mask to protect your lungs when cutting fiberglass.
Saran pakai masker bg, debu resin itu sangat berbahaya dan berat. Sekali masuk paru2, selamanya akan tetap berada di dalam paru2. Yaa emang kalo mati si udah ajal yah, tapi apa ga kesian sama anak istrinya ntar ? blom tua udah sakit2an dan kurang produktif buat nyari nafkah. Perahunya luar biasa, pasti ringan dan awet.
Great looking boat and it looks like it handles well!
Got that safety squint going when he's grinding on that fiber glass. ☝️
Very nice! It did surprise me that you didn't use a scale to weigh the amount of epoxy and hardener. (The epoxy that is for sale where I live needs to be in the exact amount. Too much hardener and the epoxy becomes too brittle, too little hardener and it will remain sticky.)
It can be measured by volume aswell as weight, depends on the brand.
2:57 I'm pretty sure that is not epoxy , but polyester, and MEK hardener.
For lay-up work like this it's almost as good as epoxy, but epoxy cost double the price.
The ratio hardener to resin is more important for the "open time" then for the strength of the finished product. Too much MEK hardener and you have only very short time to lay-up the fiberglass. Specially in the tropics.
That was Polyester Resin, I can smell it from here.
I use epoxy for some things, and polyester for others. For a general purpose, knock-around boat, I'd use polyester every time. Far, FAR less expensive, and the weight difference on that project would only be a couple of kilos at most
That boat turned GREAT, by the way. 10 out of 10
these guys have so much ingenuity they can build a bass boat out of saran wrap and pool noodles
Use the old boat as a plug & make a mold. Make many canoes to sell. All your friends will want one.
Use hot water spray (from water heater tank) to quickly remove all margarine before glassing interior.
nice
can you tell us the name of the materials that you are using ?
Fiber cloth
Red resin
Catalist
Talc powder or resin powder
Margarine
Pvc pipe
If you take a piece of thick wire and bend it into a shape like a paint roller the put on the roller part two different size washers go large small large small etc… then bend the end of the roller to stop the washers from falling off but can roll ezy without much wiggle room then use it to roll the glass after wetting it thoroughly with resin the roller is better to get out air pockets and even out the resin saturation
ini mah bukan plastic bang, tapi manteb dah idenya, boleh di tiru👍
Just Incredible! Congrats!
Félicitation superbe réalisation et superbe video
Nice job, well done.
MANTAF BANG. SALAM DARI PANTAI UTARA (SAMBAS)
Very nice work.
Thanks a lot.
At the end of the day for his frame he made a lightweight simple canoe, that works perfectly, despite doing everything wrong!
OK, so share a link with all of us showing your canoe built from scratch, done the "right" way - and do it as inexpensively as he did. Oh, and don't forget to weigh it. And until we see a follow up video where his canoe is swamped, cracked, or otherwise made useless, I'd say he did everything sufficiently correctly to meet the basic requirements of form and function.
salam hadir lagi bosku dari kepulauan aru maluku salam sehat selalu dan salam kreatif
Very very nice
Gotta say it very good job man 👏👏
Thank you sir 😊😄👍
Do margarine goes, if make fibreglass mould from fibregalss kayak or fibreglass canoe?
Yes
Muito bem 👏🏻👏🏻👏🏻
Saudações do Brasil !!!
wear a mask brother. the dust will kill you.
very nice work.
Beautiful!
Very, Very Nice !
Excellent ! Thank You !
😎👍
Mantap bang budi,segedong,👍👍👍.
So, to build a canoe, first get a canoe...
Make a double ended kayak paddle it will be easier to paddle and more stable.
Padu sampan nye trims bg sudah berbagi ilmu
Bahan beli dimane bg ptk
Naga sakti fiberglass, jalan Tanjung pura😊😄👍
@@bkscreative siap bg terimakasih info nya
Too good you are bro....
❤❤❤❤❤❤❤
Necessity is the mother of invention!
.
Flores Timur hadir...slm sukses selalu..👍👍👍
What is used to coat the Fiberglass cloth , epoxy or plastic?
Resin 😊😄👍
What type and brand of resin or to melt polystyrene?
Looks like PVA glue
Red resin
complimenti ... veramente bella 😍
how many kilograms does the kayak / canoe weigh?
20-25 kg😊😄👍
what is the density of glass mat?
300😊😄👍
is this in the Philippines?
Indonesia 😊😄👍🇮🇩
what is the white powder mix with resin and hardener?
talc powder or resin powder, used to thicken resin😊😄👍
Zip ties that's great
Canel ini dari negara mana?
Indonesia 😊😄👍
I'm subscriber from Philippines ilike yung content I request next diy jet ski☺
He really needs to wear a dust mask when cutting that fiber glass why a power tool. That dust is bad for your lungs.
...with a power tool.
برافو برافو عمل رائع
I think that it not plastic as claim at the title... this process is call fiber molding....
The fibre glass boats for the Americas cup were called fantastic plastics
Habis brp kg resin dan mat fibernya
Mat 3kg
Resin 12kg😊😄👍
離型剤のような物はなんですか?バター?
はい、バターまたはマーガリン
Parabéns!!! Muito boa a construção!!! Brasil - RJ - Capital.
what is the name of the freezing liquid? And what is the name of cloth? Please.
Fiber cloth and resin
It is chopped strand mat (CSM), comes in various "weights" from 150-600g/m^2 and polyester resin and catalyst (1-2% depending on ambient temp). Needs to be measured!!! You should also finish with a layer of woven fibreglass roving (fabric). And you should use a hard ridged roller to saturate the fibres, not a soft brush to stipple. That way uses far more resin, and leads to far weaker fibres.
Thanks perkonsian nya bro
I now know a new use for butter. Lol
😂
Don’t cut fiberglass without protection.
orang pontianak kreatip 👍👍👍
Excellent!
Safety first ! 😎
very very COOOOL
မြန်မာလိုဘာသာပြန်ပေးပါလားလို့
NICE !!!
The traffic sounds like the Philippines.
Indonesia 😊😄👍🇮🇩
@@bkscreative The traffic sounds the same because similar loud motorcycles are used.
I started itching the moment that angle grinder began trimming the fiberglass.
First I have to get your experience then I will make it at home 😂😂
So much wrong with this. Why not make it in one piece for starters? No gel coat, no multiple layers, no measuring out resin and catalyst, no roller to maximize fibre saturation. This is NOT how you build fibreglass boats. I've built dozens of glass fibre kayaks. You fair and polish the plug (here the original boat), take a mold off the wooden plug, then build the final kayak in the mold.
The laminate needs to be built up in one continuous process to achieve a chemical bond.
Using margarine as a release agent will contaminate the surface and lead to delamination of the subsequent layers. Use wax, and polish it.
Yes, you're right, but for some people who don't have enough budget and long hours, maybe this video is the solution😊😄👍
@@bkscreative you are absolut right! Improvisation is the Art to survive
@@hans-dieterjung4026... Improvising when you have access to the entirety of humankind's body of knowledge... That is not at all a good survival rule
Sorry buddy but he seems to be far too busy enjoying what he made to listen to your opinion about what he did wrong.😂
Why don’t you show us how you made it, many people find this video very informative at a low cost.
Hi. Please betyer add a loat of polyuretane spray foam. My very best regards and respects.
Ok, so to make a boat at home, you go out and find yourself a boat......
Nanya bang berapa harga 1 sampan nya
Asal mana bang?
berape panjang nye, lebar nye dan tinggi nye ni bg
Panjang 4 meter
Lebar 65 cm
Tinggi 25 cm😊😄👍
@@bkscreative how many kg does the boat weigh?
@albumkoretsky about 20kg 😊😄👍
very minimalist has glassfiber, rules have how long boat have etc, 4 meter need 4 level glassfiber to boat ewerywere. and this have minimi what need do, normal need 5-7 level glassfiber 4 meter long boat. then have normal strong boat. big boat etc, 30 feet sailboat need 1 inc glassfiber mean 30-40 level glassfiber all boat. or 20 levell under then honeycomp and then 10 level, save little glassfiber about 1/4
For this kayak, I only use 3 levels of fiberglass 😊😄👍
@@bkscreative its ok, have small one men boat
😲👍👏👏👏👏👏👏👏👏👏👏👏
parabens
PS. Alot of polyuretane sprayable foam!
Tanks
🎉
Bisa berapa orang naik nya
Max 2 orang 😊😄👍
Uggg... I hate the smell of polyester....
Berape lapis tu?
3 lapisan 😊😄👍
It carbon fibre
👍👍👍🛶👍✌️👍🇺🇦🔱🤠
I got about half way through this before I felt sorry for people living in 3rd world countries and how they had to build things with inferior materials.
Then, I realized, this is posted on UA-cam. This person has access to the entirety of human knowledge.
Original boat leaked. Why not use polyester resin and fiberglass to seal the original boat?....No clicks, No views.
Instead, lets use the original boat to make a new boat, without watching other videos on boat building.
I admit, you got me with the clickbait. Good job. Hope you do well on UA-cam, but I won't be watching any more of your videos.
You fooled me once...
Maybe he needs a lighter weight boat.
Well done 👍
Creative idea everybody can using this method
Homemade fibreglass boat with plastic reinforcement🤣🤣. Two ply in calm waterway with one....doubt it will hold in rough water🙊
I doubt you will hold in rough water ….
👍👍👍👍😉👋🇺🇦 привіт з України!
😊😄👍🇮🇩
When I saw the colors, I was also thinking: Viva Ukraine!!! 💙💛