Peugeot and Citroën BSI - clone, pin code read, virginize/ reset.
Вставка
- Опубліковано 5 жов 2024
- Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
Hi
In this video I demonstrate what to do in order to reutilize a second hand BSI, or how to retrieve the pin code from your actual BSI module.
There is tools out there that can do this through the OBD port, which obviously is more practical.
At the end of the video I decide (that was actually the plan from the beginning...) to program rather than the virginized file, the actual dump from the original faulty BSI.
Reason why just before I press the write button the file changes...
But hopefully I managed to show you all the options.
Here is the link to the video on how to then program/code the blanked/Virginized BSI back to a car.
• Peugeot Citroën blank/...
NOTE THAT THE LINKS BELOW ARE FOR A QUICK REFERENCE ONLY!
FEEL FREE TO DO YOUR OWN RESEARCH PRIOR TO HIT THE "BUY" BUTTON.
Flux used: NC-559-ASM-UV
www.amazon.co....
To clean: Isopropyl Alcohol
www.amazon.co....
Fiber Glass Cleaning Pen:
www.amazon.co....
Soldering Iron: Temperature controlled soldering station.
www.amazon.co....
Hot Air Gun Station:
www.amazon.co....
Desoldering Vaccum Station:
www.amazon.co....
Remote Tester:
www.amazon.co....
www.amazon.co....
Uni-T clamp meter:
www.amazon.co....
EEPROM Adaptor:
www.amazon.co....
X-PROG:
www.amazon.co....
Hope this video contains information that you can take further.
I also hope that you enjoy the video.
Any comments or questions please put them below.
Like always, thank you for watching!
Hi. Is it possibel to send you my bsi for repairing? I have a citroen xsara where the sidelights doesn’t work. Which country are you from?
Hi
I am in the UK.
The problem is that I will not have how to test it, and I don't like to do repairs without be able to test the result...
If something does not goes as planned, I will not have how to tell, and then you will be receiving it back, to find out that is still no working...
Sorry, I can help you through diagnostics, and guide you through (Consider to support my channel and all the hard work put into it at www.patreon.com/LMAutoRepairs
Thank you), but that is about it...
(I will love to help you to the best as I can!
ua-cam.com/video/ka-Yrflcd-o/v-deo.htmlm55s)
Hope you understand!
I understand. You’re right. Your respons just tells me that your take pride in delivering high quality services.
I will look at the channel. Thank you.
Hi mate got a water damaged ECU from a Peugeot 207 unable to read old ECU has its dead and doesn't contain a eeprom chip.
Could I virginise a repalctment ECU then read the pin from the bsi to allow me to programme the new ECU with Peugeot planet ?
Thanks
@@joshbennett6293
Yes... absolutely you can...
👍👍👍
Hello, i can not find the connections for the Citroën c3 Bsi F02-00. Do you have a link or tell me how to do it please. Connections are also possible from the connectors so i can also hook up there if needed.
Po prehozeni chipu do jine bsi bude imobilizer fungovat otestovane ,tak stejne jsem kdysi vymenil je chip na vadne ridici jednotce motoru do nove koupene a taky vse bez programovani klice fungovalo 👌
Привет из Санкт Петербурга, спасибо огромное за видео все сделал как у Вас на видео Вы очень помогли
Thanks for another great video, I learned a lot from your videos and I have been searching for this type of video on how to virginise bsi, you actually make my day.
Sagir ILIYASU ADAMU
Thank you for watching and for your comment!
Glad to know it was helpful...
Pls sir help me with help me with 2003 Peugeot 307 pin out as you do in this video iam clad with this video the order model of this bsi thank sir
hi iam doing thesame work as you are doing i dont know how to get the right mcu you didnt show it on your video
Hello from portugal mate. Can you make a vídeo where we can get the equipment you use. Hardware and software? Also some tips for begginers. I like your vídeos. You are great. It would be nice to have a vídeo of telling how you start learning all this stuff .
Tell us your professional story mate
By the way my name is Ricardo Alves 😊
@@grupoportugalgeteasy7975
O meu é Luis Mateus...😉
I learn as I go along really...
I have no background on anything to do with cars...
👍👍👍
You are braver than me good video, question, can you replace central locking relay, as me seems to be faulty, Peugeot 206,2005,1.4 hdi.
Hi
I can't see why not...
Thank you for watching and for your comment!
Hello,very owesome video i am learning new things from your teachings keep up the brilliant work.
tronics digital
Hi
Thank you for watching and for your comment!
Hello, good afternoon and congratulations on your professional and interesting contribution to your videos. I have a question if you would be so kind as to help me. I need to access the board of a control unit, it is an external tuner, of a motorcycle to be able to eliminate or release the Vin since when connecting to the motorcycle it is linked and does not allow me to use it for the other one that my father has. It is the Scream eagle super tuner model in case you know it or you can see the model on the web. I know it's possible but the person I knew because of illness is no longer dedicated to it. I would be very grateful if you could help me with something please
Hi
Unfortunately I have no experience at all with that...
I would guess the vin is stored in a eeprom or mcu on the module...
It might be possible to do it through some sort of interface rather than open the module...
Again, I never worked with anything like that...
👍👍👍
brilliant mate thank you. gonna try the clone method tomorrow. cheers!!!!!
👍👍👍
Loved it brother. God bless you
Great deal of knowledge. Appreciate it
Name some software for us please. With there details.
Where are you from bro??
Sohail Khan
Hi
Most of the softwares come with the tools to be fair...
Thank you for watching and for your comment!
good video,,very well explained,,,ive left a c4 bsi useless after fvdi millage correction,,,any easy ways out ??
Never had that issue...
Can you still communicate through OBD?
I would suggest either reflash with Lexia or Diagbox... that not possible, get a dump from a good one, and do it on the bench... again, providing you can communicate with the MCU...
Thank you for watching!
Tanks agen to thes amazing videos.
From where did you get the pic of Bsi connection to carprog?
Sorry I didnt hear what you said at the start, what is the first software your using? and what is that serial box thing you are using (do you have a video that covers this)?? Realy love your videos.
Carprog?
No, I don't have videos on this tools...
But I have several using them...
Thank you for watching and for your comment!
Was it Carprog???
@@CapuaSon
That's what I said...
very good my brother
Thanks!
👍👍👍
Hi, thanks for the reply, these boards you are working on just split apart but I would be very interested in seeing you do similar work with a new style bsi eg citroen c3 Picasso I had a nightmare with one keep up the good work pal
lkim08
No worries... I do this things as a hobby/part time... and some times I just want to get the job done... and do not have time to record... but will try if one comes around...
good work friend but when you clone the bsa of psa that always usually fail with the time that software you used thanks greetings
I reseted a few... never had an issue...
Thank you for watching!
Hi, You mentioned Carprog was running out of credits, do you have to connect it to the internet to get more credits unlocked on the device, and I think you mentioned you have a way around this, how does that work?
Thanks
Hi
I just program the Atmel processor with a file with 50 credits, before it runs out...
That's the way round it...
Thank you for watching and for your comment!
tanks to you,today i read my first bsi
WoW
Congrats!
Thank you for the feedback!
Hello LM Auto Repairs, How can I find the connection points on a Valeo BSI J02 (FNR: 9651197480 A, FNC: 9651196780 A) and Valeo BSI J04 (FNR: 9651197680 A, FNC: 9651196980 A)? Can these two be reset using the Carprog v8.21?
Good teaching I having watching this video for long time pls sir how do get the software ecu vonix pls give me the link thanks
Please sir i realy need help i have Citroens c2 2006 & c3 2003the c2 I done key went well then car not starting again and the c3 I done mileage on the cluster and bsi but now car not starting start some some time why?
after write the vergen fill in bsi > you need program a new key ?
Yes...
Thank you for watching!
👍👍👍
well explained...and another best video as always..thank you bro..
😊
Thank you!
Hi,
Awesome video, very well explained.
Would you mind sending me the Immo killer V1.1 software.?
I'll really appretiate it.
Hello sir. I have peugeot 206 1.6 16v 2003. Speed limit is not working. Code p0501. But the car Don have sonsor Don know how to fix it can u help me please
Hello and thank you very much for all the infos you´re sharing. I have the same BSI. Original + another 2nd hand one.
I`m trying to read it with the same tool "CARPROG" but it doesnt read... I dont know why. CARPROG has been used before and its working... What could I do? Is it absolutelly neccesary to have the PIN when instaling a Virgin BSI with peogeot PLanet?
Yes... you need the pin...
Thank you for watching!
Hi, nice video...
Tell me have you pinout for valeo bsi cn4, xsara 2.
Best regards
Please can you show me how to reset 3008 2019 bsi
thank you ! very good explained !!!! I learned a lot ,all time whit your videos !
which carprog you can recommend me ? or xprog ?
Alexander Krachev
Hi
I would recommend the latest one... on both, carprog and x-prog...
thank you answer
I'm looking to virginise a mk2 berlingo bsi, can you point me in the right direction to get information on this. Also are the amazon listings in your description the right tools for the job?
Great video and maybe even greater comment section!
Hey bro, best channel ever. Thank you a lot for sharing your knowledge with us.
Can you help me with my Citroen Xsara N2.
I want to read out the pin code and virginize the bsi.
It is a Valeo 730 045 12 BSI var C CN2.
Which carprog adapter should I choose and do you know the pinout?
Hi
No need to read the pin if you are going to virginize...
What is the chip inside?
Is that an external eprom, or is a mcu?
Thank you for watching and for your comment!
@@LMAutoRepairs
thanks for answer. I want to virginize the bsi and then install and initialize in my car, because the original one was water damaged.
There are a lot of eproms, which one is the right?
I tried to read out the 95040, but there were only zeros and I don't know for what this eprom is.
Then there are two microcontroller 75076358 & 75076359 with software version V3.231
hi love you videos great job, have a question.. have two bsi boxes veleo GOX-00 ONE IS BAD BUT I HAVE THE PIN... THE OTHER IS GOOD BUT I DONT HAVE THE PIN CODE....... CAN I SWITCH AROUND THE EEPROM CHIP AND I WOULD LIKE TO KNOW THE WHICH CHIP IS THE EEPROM THE CHIP NUMBER
Hi
I believe that on that one is an Motorola MCU... no external eeprom...
So a bit more tricky to swap...
Thank you for watching!
Does the same thing apply if you would like to replace a Peugeot/Citroen Engine ECU ,so that you can keep the same BSI and Key?
Auto Sport
Hi
Pretty much yes....
But depending on the ecu, and providing you have access to the data on the old ecu, it might be easier to just clone it... saves you all the mess about with PP2000...
Thank you for watching!
is this video part 1 then they other part 2 the programme ing side
Hey, i have a question. My BSI is blank. And i want to ask, if i only change my BSI and keys from another car, will it start, or i have to change the ECU also ?
Hi
You will need ecu as well...
Thank you for watching!
Hi! I have BSI from C3 I that wont go to sleep and empties the battery in 3 days. Everything beside this is ok with the car. I think to buy s/h BSI with same number and swap it. Can you simply tell me the steps I need to do to put the s/h BSI in and keep the ECU and keys? Or maybe other suggestion to fix the drain problem? Thanks!
Check the drain by testing independent circuits...
It might be that there is nothing wrong with the BSI, and is something else that is preventing it from going to sleep, and replacing it will not fix the problem...
Thank you for watching!
can you tell me what equipment i need to to read and virginize a c2 bsi and a list of the programs you use please thanks in advance
Depends on the chip...
GOOD TEACHER YOU FEED ME WITH USEFUL INFO THANKS FOT THAT PLS I NEED PIN OUT PEUGEOT 807 BS WITHI CAR PROG 2.2 LITER PETROL ENGINE PLS FEED BACK
Hi, I have a 2010 Peugeot 308, Johnson’s control BSI that is corrupt/faulty. I want to read the eeprom chip. It has a 95128 chip. Could you help me with where to get the software to Virginise the eeprom dump? Thanks
So, I have broken bsi, I read from memory, and usually need first clear file and program bsi using clear memory file. Then I need read it again, then write using original file?
Luis ... Do you think Ktag could do that kind of job ?? you use carprog and so the wiring pin probably be different ..
Hi
K-tag is not for this type of work...
Thank you for watching!
Hi mate, my ecu data was corrupted, so had to get that data recovered and a new eeprom upload to the Ecu.
Now the bsi eeprom needs to be read and then written to 2nd eeprom.
Any idea what would be the easiest way for this?
Where is located on the car the BSI (that you are resetting) on a Citroen C4 Grand Picasso 1,6 HDI ,year 2010 diesel ?
Usually under/behind the glove box...
Thank you for watching!
Good morning, why don't you activate the caption? I have difficulty following your videos, thanks
GOOD TEACHER AFTER I CHANGE ANOTHER BSI SO I VAGINE THE NEW BSI CAN I USE THE OLD CODE TO PROGRAMM THE KEY PLS FEED ME BACK THANKS
Once the BSI is in a blank state, you can use any valid code..
👍👍👍
Ok.So what did you factory reset, blanked?? Because you stated in the video at 11:00, that ECU. I think you wanted to say the MCU eeprom of the BSi. Correct or I'm wrong. Thanks!
Yes you are correct... at this time sometimes I would refer to modules as ECU (electronic control unit)... 😊
Thank you for watching and for your comment!
@@LMAutoRepairs Keep the good work up! We people have to learn to repair things again not just swap to new parts. Thank you and all the best!
@@leogetz2668
👍
Really glad to see Portuguese doing great, i have a problem with the JC BSI from a 2009 C5, i Run fvdi to learn PIN and kill it. Have a used One Now, the problem os that i need the PIN to Virgínize it. Can i work the pinout with FVDI or what the best program to read BSI on beanch. Sorry for my inglish not as good as yours :) um grande abraço da velha pátria
Nelson Santos
Hi
Obrigado!
That BSI, does have an external eeprom, or is the one in the MCU?
There is other tools capable of reading the pin from through OBD...
Do you have any other programmers etc?
Thank you for watching
Cumprimentos...
LM Auto Repairs good question but i dont know ir it is MCU, is there a way to find out? I only have abrites and lexia3/diagbox
Nelson Santos
Ah... open the old BSI... and see the system... if has an eternal eeprom...
LM Auto Repairs well i manage to plug a new flash to my original BSI and it came to life, problem is the flash isnt the correct One soo the wipers always on and the car os manual and the flash os for automatic
Nelson Santos
Ok... at least you made some progress...👍
You need to get the correct one... was that flash virginized?
If yes, program the BSI to the car... and see if you can then flash it again with pp2000...
Give me the BSI details... and will see if I have a flash on my server... but don't hold too many hopes....lol
GOOD VIDEO I HAVE A QUESTIONS FOR SIR FIRS CAN I USE THIS METOD FOR ALL PEGEOT BSI IF SO PLS FEED ME BACK THANKS
Kind of... different BSI slightly different methods...
👍👍👍
great vid, can you please upload links to softwares and upload to a site for all, just put links in description(megaupload or such) you can also read the code if your good with hex editors right?
Andrew Oconnor
Thank you for watching!
great job like always wide and clear brother
sadik mamoun
Thanks...
Great video, loads of info.
Could you help with wire install for citroen picasso bsi
have carprog maybe clone, where can i find wire colour codes
so i can solder onto 95160 eeprom
paul lee
Hi
If the eeprom is accessible, better to remove it, do the work and put it back on...
With car prog, you have some documentation that tells you what wire colour is what... from there you need to know which bsi you are working with...
Can you access the eeprom?
Nice video , I have couple questions about doing bsi and ecu , could you recomend me some diagnostic tool wich i can use i would really apreciate it since i cant make a choice wich one can help me out
Depends what you want to do... you have seen the ones I have used here to do this work...
Thank you for watching and for your comment!
@@LMAutoRepairs well I've wached you used carprog for bsi and xprog for ecu thats the part thats confusing me
@@ervinhodo9908
X-prog should help you...
There is other eeprom/mcu programmers out there, like the Xhorse, orange, etc... depends how much you want to spend...
@@LMAutoRepairs can it be done with obd port without the soldering you mention that in a video
@@ervinhodo9908
This one...
www.obdexpress.co.uk/service/psa-bsi-tool-for-peugeot-citroen-software-and-operation-free-download-136.html
If you find one...
But I never used it... so can't really comment how good it is...
Hi,
How do you know the correct mcu model?
And is it possible to know if it's a eeprom or a mcu?
thank you for all you doing
The model or mask is written on the chip itself...
Thank you for watching!
@@LMAutoRepairs Thank you for your fast answer, you're the best!! I have a 307 (2002) with lock button flashing and the car wouldn't start. I think the problem come from the BSI... I will try to virginize the BSI and program it.
I take it , that's an early version of carprog? having to reset the counters.?
Yes... it is... I need to flash the atmel chip before reaches 0 credits...
Thank you for watching and for your comment!
You are doing copy from knowed bsi key code then all the software it is right? Code is same the programmed all bsi?
No... each BSI or car will have its own code...
laguna 2 2003 otomatik iç sigorta kutusu bsi değişecek programlama gerekiyor mu? Direk alıp takacakmıyım?
Hi, great tutorial. I have a 2002 307 2.0 which had water in the bsi. I have found another bsi but need to clone the eprom from the original. It's a Valeo bsi, I need help on how to connect carprog to it. Cheers and many thanks for the great info.
Hi
I can't post picture here, however, do a quick google search and you will find it in no time...
Hy, thanks for the video. I have a problem with the central locking system and I suspect that the problem is coming from the BSI. I have a C4. The problem is that I can lock the doors with the remote key and it works perfectly, no problem at all. However, when it comes to unlock the doors with the remote key, it doesn't work except the boot. The button on the dash does exactly the same as the remote key. Press it once and all the doors lock. Press again and the repeater lights flash but the locks stay locked - no clunks or other noises. The receiver also clearly works as the side repeater lights flash briefly when both the lock and unlock buttons on the key are pressed. The snag is the unlock process seems to stop there. I have read in some forums that it is a BSI problem, to be more exactly relays faults. So what they do to solve this problem is to remove (unwelding) the relays that control the central locking system and put some other relays or change completely the upper board as it appears to be non-unique, so changeable for any other board. This upper board contains a number of relays which amplify the signals from the computer. The only unique board that contains the VIN and all the programming is the lower board so unchangeable. My question is, do you know what relays control the central locking system? Could you please send me a photo, if you know which the relays I am looking for are? Sorry for my English I am from France, lol.
Thanks.
JJ sam
Hi
That's correct... the mains circuit board can be changed on its own...
Which relay actuates the central locking, depends on the BSI type... there is different makers even on cars of the same year... so it all depends on which one is fitted on you car...
Ok, Thanks.
Sorry to disturb you again. I took a look to my BSI and the reference of the BSI I have the problem with is this one: 9661940480 BSI 2004 H05-0131006. If there is any chance you can help me identifying the relay that controls the central locking system that would be nice of you.
GOOD TEACHER I HAVE DONE THE BSI REST OK I HAVE OLD BSI CODE OK I TRY TO PROGRAMM BUT THE TRANSPONDER IS NOT PROGRAMMING DO I HAVE TO CHANGE THE TRASPODER IF SO PLS FEED ME BACK THANKS
Yes... the transponders will need to be new...
And the remotes...
👍👍👍
You do fantastic work lad you are the man for C4 picasso I have a question you may be able to help me,2015 c4 1.6 hdi, warning came up for low additive (Pat)fluid fluid was topped up but code won't clear so went and bought new tank and pump programmed them in fault still there,the fault of is cleared out of all systems except the BSI it won't clear from it comes right back every time,any ideas lad
Hi
Difficult to tell...
What fault is coming up now exactly?
Does live data shows anything out of the ordinary?
👍👍👍
@@LMAutoRepairs engine repair and service light,multiplex pump fault is in BSI and won't clear comes back every time,a new pump and additive tank have been fitted and programmed in no codes anywhere except pump one that won't clear
Can you communicate with the additive pump?
@@LMAutoRepairs yes it knows new parts are fitted but been french as you know you have to clear from all ecu's before fault will clear but comes right back it's put the car in semi limp mode won't drive in auto only paddle shift but also under powered I'm told this is a protection thing,anyone I have asked in Ireland about Lexi software they say no don't have ,wiring checked yellow wire is live not sure witch is data wire Back to bci green or green with yellow strip,all working in back of car have been checked would it be bc is itself lad do you think,and thank you so much for taking the time to reply to me
have cardprog to clone bsi body computer, and I ask you about you can tell me about eeprom 95128, its only this I need to copy over too my new bsi body computer? The car is peugeot 3008 1,6 hdi models 2010
Hi, Very good Video! I have a few questions for you : Can I read the eeprom with an universal programmer?for example I have a Mini Pro TL866A.Can I read it with this programmer?Can I connect the wires like your connections?Will it work?
Hi
It all depends on the bsi... some have an eprom, and some other ones have an MCU...
They are read differently...
Thank you for watching and for your comment!
@@LMAutoRepairs Hi, If I take the eeprom or mcu out from the board and I read it with my programmer,the resulting bin file is good? Or it must be readed with special tools?thank you!
@@fychy
You can do that...
👍
If you can read the old Bsi file if faulty. Can you then just write that file to the burnished bsi as long a they have the same EPROMs. Can launch xprog 3 be used
Yes... those tools will work, as long as they support the chip in question...
👍👍👍
Hi Mister
You say on your comments : "There is tools out there that can do this through the OBD port, which obviously is more practical. " How to extract the PIN code from ODB2 port. I have Lexia3 cables and Diagbox program, can i do with them or is needed any other app ?
Lexia is the OEM tool... Will not do it..
Look for PSA tool... rare to find though...
Abrites is another option... but horror stories out there...
Thank you for watching and for your comment.
@@LMAutoRepairs were you able to find and test someone of this apps ? The dealer extract the PIN code from VIN number ?
@@MrLeofezollari
I believe they have them on a database...
Вы не могли бы скинуть программу pego calculuatore code , которая у Вас на видео.
Hi is the cluster with in the bsi unit or is it a separate unit? unfortunately I did what you said an put a bsi unit in and the milage has gone up I've taken it back and put my original one back in it drives but just the locking system is broken not sure what to do next the place I went to said it's a 50 50 chance if I could ever get my milage back any help would be greatly appreciated
Have you reset the BSI before you put it in?
Looks like you haven't...
The mileage is stored in the BSI and cluster...
The way you drop is down to the real mileage, is by virginize the BSI, and change the mileage on the cluster to the correct one...
Once you plug the blank BSI, the mileage from the cluster is transferred... so you ended up with the correct mileage on both...
Obviously the blank BSI will then needs to be programmed... you will also need new transponders and remotes...
👍👍👍
Hi which tools do you refer to when you say it can be done through obd port ? and which tool do you recomend for this xprog or carprog ? By the way good video like it :)
Kosa Arpad Szilard
Hi
You have for example, a tool called "PSA BSI Tool" that reads the pin through OBD on certain models... there is other similar..
Hope that helps...
Thank you for watching!
Hi thanks for your answer. Thats what i thought :) no go for my model 2002 peugeot 307. I just changed the bsi and ecu +key to get it started . Everything works now on car well almost :) . But i noticed that the bsi was not the original type which was in car before. So im assuming that (after doing some reading with pp2000 where everything looks fine.) no communication with instrument panel cluster, and not recognizing the door modules is because of this . So next step is trying to virginize the old bsi . For this i need carprog as you showed in video. So i plan to buy one can you reffer someone who sells and can be trusted?
hi brilliant video, could i ask some advice. I have a 2001 406 hdi 2.0 estate and the bsi has burnt out on a couple of tracks i repaired them but i still have lost dash service indicator and mfd, the wipers and central locking. Car did start and run with these faults but it now only turns over cranking. Would i be best off trying to find a 2nd hand bsi and virginizing it, then inputting using planet2000 the vin and pin that i got from peugeot?
davedree
Hi
You can do that... should work.
You can try to take the pin from your actual BSI... providing you have the tools...
Good luck...
hi imswavr a bsi is fitted and the ecu is a sagem s2000 thanks to advised tino
hi imswavr yes we removed the immobilizer using immo killer s/ware
+tino Choolun
OK
Does the car have climatronic?
Without checking diagrams I am not sure, where the signal to engage the AC pump comes from... if from the engine ecu, climatronic module, if fitted, or bsi....
What version your carprog?
Is it online version?
Hi
No... my one is an older one... not the online one...
Thank you for watching!
Hi
Interesting video.
I have 307hdi that had the neg battery terminal corrode away.
I replaced battery and terminal..reset everything now all works but front wipers and resetting day/date on facia.
Is this a bsi fault? The wipers certainly seem to be??
Hi
Check basics first...
Fuses etc...
You can gave a better idea if you check it with the scanner connected... so you can look at some live data etc...
Thank you for watching and for your comment!
@@LMAutoRepairs
Hi
Replaced com switch and checked wiper operating.. All OK. Replaced underbonnet fuse box and check operation.. All good there. Just seems odd that the bsi spiked on the wiper control?
@@harwoods11
Ok...
It might be the BSI...
One thing, have you applied 12v directly to the wiper motor?
Does it runs?
Hi
Thanks for reply. Yes.. The wiper motor works when connected from an outside power supply.
Is it poss to fit a second hand bsi?
@@harwoods11
Hi
Yes... but needs to be virginized first...
Olá Hello I'm thinking about buyin a programmer what do you think is the best Orange 5, xprog or tl866 ?? I have carprgo 8.21 and the cheap ch431a ... thinking about be able to read and write eeproms remap edc15 with the big sop44 flash and plcc32 and also be prepared to do some immos and BSI(like that).... thanks in advance
Hi
I am a bit biased, and to be fair, I only ever used X-prog, from list you gave...
X-prog is quite complete... can't really go wrong with it...
👍👍👍
hi and thank you for your awesome videos.
Could you please suggest some good softwares for deleting DPF/EGR from ECU file?
Software on which you can load the file which was extracted from ECU, and delete DPF or EGR.
Thanks.
diesel parts
To read the ECU there is loads, but all depends on the ECU it self...
From KESS to K-Tag, Galetto, piasini etc...
To delete the DPF from the map, that's a bit more tricky... you can easily get hold of the ECU safe and volta... but they are limited and not always work... there is more out there just Google it... The best way to delete the dpf though, is manually with winols for example... but that requires experience and know about maps etc... hope that answers your question...
hello my friend, did u tested the bsi after virginize it? and how can we put the new pincode or it just take it from ecu? or must virgin ecu too? regards
Hi
Read the description of this video...
Hope that helps...
Thank you for watching!
Hi, could you share me the software that you are using to read data and calc. the Peugeot pincode? I need to add key for 2004 Peugeot model 206. I am also looking for the connecting wires that you are using.
Hi
Do you have X-prog or a similar programmer?
can u test if really the FVDI kills the BSI jhonson or not please .
Hi
I never tried it... but people says it does... at least the clone one...
Thank you for watching and for your comment!
@@LMAutoRepairs some says that u need just to keep the battery voltage above 13V
@@MrFOXMAROC
For any programming etc... a charger needs to be connected....
That's true, i would like to thank u for the effort that you put to produce those videos.
@@MrFOXMAROC
Thanks... more to come...😉
Can you do a hardware video please with all the hardware you use and where to but thanks
Hi LM Auto
After my question about fixing the BSI AC problem (Not yet fixed) I made an horrible mistake (NOT listening to your warning about the mileage) and borrow an old BSI from a friend and connect it to my car which result with +40K to the car cluster. from 160K Now it show 200K :(.
Is it possible to reduce it to the lower mileage ?
I have PSA Planet + Carprog in hand. I can get any software for this mission if needed.
You need to remove the cluster and do it in there...
Put the cluster to zero miles, or anything below the original miles... Once you connect your BSI again, the miles will correct...
Unless you have already plugged your original BSI back in... which in that case, you made it worse.. and you need to modify the mileage on both now, the cluster and the BSI...
I can't remember wich chips are in those modules... but once you open them you will see..
Good luck...
👍👍👍
@@LMAutoRepairs
Thanks mate.
As I understand there is an eeprom chip there? If so NP.
Yes...
Please I need your help am having problem with replacing bsi on 3008 2019 right now the ignition comes on with the old bsi but the car can't start
What testing have you done to deem the BSI as the problem?
👍👍👍
Je confirme que sur 207cc la montée des lève-vitres n'est pas séquentielle, il faut maintenir le push appuyé. seule la descente est séquentielle (appui au 2ième cran du push). C'est réglementaire car il n'y a pas d'anti-pincement.
Ce n'est pas "activable dans la BSI???
Does anyone know where to get virgin dump files? I need one for my Peugeot 406’s BSI.
Also, does anyone know what software is used to read and edit the mileage on these files, I messed up my mileage and now need to correct both the BSI and instrument cluster.
Very well explained
Daza Essox
Thank you for watching and for your comment!
If i read the pin from old BSI and program the new (2nd hand) Ecu with the same PIN like BSI , if will runs everything normal? (i use the same soft like you) The old ecu is destroyed and haven't got way to get the info from there :(
You need to virgin the replacement, end then program it with the car pin...
Thank you for watching!
Hi, great stuff, what else can carprog do? Thanks Jonathan
Jonathan Dean
Hi
Airbag reset, some ecu pin read... etc...
Thank you for watching!
Thanks, could you also tell me, will the zed bull key programmer tell me the pin code for a car key?
I have one key, but would like one more cut, but I don't have the key pin, it is a peugeot.
Thanks again
Jonathan
Jonathan Dean
Don't think it does...
Do you have how to programme the new key?
Thank you for watching!
LM Auto Repairs Thanks, yes I need to program a blank key, I have one working key, with the zed bull do it? Thanks again Jonathan
Pls tell me what you use in cleaning the eeprom the alcohol
Pls feed me back
Isopropyl alcohol...
Thank you for watching!
Thank you very valuable
😊
Thanks, for watching and for your comment!
Would xprog be able to copy my original fiat doblo BSI and write that to a used BSI?And after i do this will my keys etc still be recognised?Thanks.
Yes...
But as for if X-prog will be able to do it, check what MCU or eeprom you have on that particular BSI... just to be sure that X-prog does support it.
Thank you for watching!
@@LMAutoRepairs I actually posted my problem on another video but i cant find it.I replaced indicator relays on my bsi pcb.My original problem was right side indicators werent working on my fiat doblo.I replaced both relays with used ones,when i connected everything keys weren't recognised by the car and 'both' sides then didn't work?
Made progress today,got two new original type relays from China,now i am getting outputs from bsi to both sides now!But they are flashing quickly and front indicators on bith sides aren't working??
It's slight progress but keys still aren't recognised?
Hi! Can you share a link where the BSI cloner can be found?
I would have to Google it... but you can also do it yourself...
Thank you for watching!
@@LMAutoRepairs Thanks for your answer. I searched for it on Google, but didn't found any BSI tool that can be bought. Can you send a link from where you ordered yours? Thank you much!
Dear Sir, I have a problem with Peugeot Boxer van 2011. The only key I have broke, I'm not the first owner of the van, so I don't even have a card with the code for making a new key, but I can read the ECU, do you have a program with which I can read the codes for making a new key? Thanks in advance for your reply.
To read the pin code from that depends on the ecu... what tools do you have to read the ecu?
Do you have how to program a new key?
👍👍👍
@@LMAutoRepairs UPA USB v1.3 programmer to read ECU, To add keys would use OBD Delphi car diagnostic. ECU is from Mageti Marelli in Boxer.
You need to get hold of the pin by reading the data...
Do you have the knowledge and experience of the name of the program that can do this?@@LMAutoRepairs
do i really need to virginize my second hand BSI? i collected my PIN from ecu using galletto. Can the galletto be used to virginize the BSI instead of carprog? i will use Diagbox to program new BSI, can Diagbox handle the not virginized BSI to program?
Hi
You need to virgin the BSI before Diagbox can do anything with it...
Thank you for watching!
@@LMAutoRepairs not having a programmer to read/write the bsi, soldering a new eeprom will do the trick?
Hi, good video, do you have problems with the colours of the carprog wires not being the same on the clones or did you buy geniune plugs so the colours match up to diagrams hope this makes sense cheers lee
lkim08
Hi
Yes it makes sense...
My carprog came with the correct wire colors... At least when compared with the pdf files that came with it...
Do you have pin out for read MCU of BSI peugeot 206???
Just look for the datasheet for the chip in question...
👍👍👍
Please how can I learn how to vaginalise sagem ecu eeprom
my 406 automatic ecu not communicating with BSI , what is the best way to replace it, is there a way to virginise it, or is there a eeprom that can be swop, thank you, I really enjoy watching your videos,
Hi
Do you mean the engine ecu is not communicating with the BSI?
Thank you for watching!
LM Auto Repairs
thank you for quick reply,
It's automatic gearbox ecu is not communicating with the BSI, It's Siemens,
Susantha Batagala
Ok... but when you scan the car, can you communicate with the gearbox ecu?
LM Auto Repairs
No I can't communicate with it.
is it part of the the immobilizer system? coz key sign is always on the dash, or immobilizer has kicked in when the ecu communication is not registered?
can u not just take they original eprom off and soldier it on the new bsi ?
Depends on the BSI model...
Thank you for watching!
i have to ask something but i dont know any other place for that so i hope you can give me some ideas in here. my bro has 2004 citroen c2 1.4. cooling fan was not working but car was running well. we took the cooling fan out and fixed it. But after that engine didnt run again, it was just cranking. i guessed that its imobilizer problem. i sent the car to who can do ecu repairs bcz i dont have any tools for that. As i guessed it was imo. He sad i fixed it by cancelling imo which is non sense solution. anyways car came to me, cooling fan working non stop even car is off too. plus engine is not going over 3000 rpm, its running in service mode i assume. Also remote key sometimes locking doors and sometimes dont(this one was exist before repairs too). so what can i do for this car? i think its all about Bsi but you know better so if you can help i can be happy a lot. Thanks i hope you can answer.
Taskin Yucekurt
Hi
Start by scan the car and look carefully at the live data...
Depending on the findings, follow the fans circuit...
Thank you for watching!
Thanks for great videos and help man. Its being hard to find citroen c2 diagrams in softwares like cardata or haynes vivid. Do you know any other one? diagram methode is so silly on peugeot and citroen. Not cable colors just numbers. Its also mentioning another control circuit in engine side fuse box too. is it true? sorry if i asked a lot.
Hi
Most likely... the ecu will probably ground the cooling fans circuit, which usually is in the engine relay box...
The citroen diagrams are usually traced by the numbers indeed...
Just had a quick look... Autodata does have the diagrams...
The circuit is slightly different, depending on whether you have AC or not...
Either way the system does have a cooling fan control module, which is controlled by the engine ecu on plug B pin J4 wire 1540 and F2 wire 1599B (1599A for the AC)
Hope that helps.
Consider to support my channel and all the hard work put into it at www.patreon.com/LMAutoRepairs
Hi Thanks for advise, i will check it out on weekend. I found diagram on autodata 3,45 you were right about pin numbers. I got the point but i just confused about Fan harness cuz it has 2 harness on fan plus socket type relay stays over fan too. tiny harness has 3 cables, main socket has 2 cables and obviously relay has cables 4 and fan has somekind device on it, i think its speed control unit. i made temporarly solution last weekend. i put a relay between battery and fan, i used fuel pump fuse socket as relay trigger. But you know with this way fan always working while engine is running. I think they messed up ecu with wrong or faulty software during immo canceling.Tps works faulty too,it has somekind buzz sound and car in limp mode,it was fine before their mess. I cdnt find original bin file on internet. I have old school eprom programmer but im thinking about ordering carprog.