This is a very informative video and actually clears up a lot of things about this vehicle, thanks a lot for taking the time to study this car model and letting us know your experience.
Shel ....Thanks for your update. very happy you keep doing this. This is because in my country, this vehicle is very popular especially from 2006 to 2012. Our major drawback with this is vehicle is the fact that Toyota did not sell these vehicles here because we drive on the left. This means its shipped as right hand and when it arrives our locals cut and switch the dash and steering with a few cosmetic touch. It makes it hard sometimes to troubleshoot electrical at this point as some sensors or fault indicators may be disconnected or removed completely. your video however has helped many here who were lucky it was just the throttle body and not electrical. thanks again
Thank God I found a Ghanaian here. Please my mechanic tried solving my vibration issue by increasing the power of the engine (Known locally in twi as "wamma gya no k) soro"). Please is that the best solution or you think cleaning the throttle body will do the work for me. (I don't have any indicators on my dashboard showing that it is electrical fault, so I think its not an electrical fault)
@@OldhamLab it is very bad solution as you are just increasing your engine idle rpm, to compensate the vibration, at the long-term you radiator will come on more often as the Engine may heat up quickly. Take note your Engine idle for this type of cars should be approx. 780rpm. Some of the vitz don't have that screw you talking about, I cannot actually tell from which year. I'll advise to check your air flow systems, plugs, throttle body cleaning, and fuel injectors.
good to know that your problem is solved, mine comes back after about a month of cleaning throttle body and fuel injector. After how long do you clean both of these culprits?
While your engine is running pull out each coil pack and hold it just above the spark plug then listen to the sound of the arcing of each coil pack as you do this to ensure the ticking arcing sound is similar for each coil pack.
Throttle body cleaned. Solenoid cleaned. PCV valve cleaned. Engine mounts replaced. Ignition coils checked with a multimeter. Spark plugs inspected. MAF sensor cleaned. My car is a 2013 Toyota Auris 1.33 Gasoline. While driving in traffic, I experience an annoying shaking when I first press the gas pedal and then when I release it again. This problem occurs in every gear, but is less noticeable in higher gears. I don't think this is an ignition problem. There is no mechanical noise coming from my car when this happens, logic leads me to believe that this is not a mechanical problem. Sometimes my car works very smoothly. The problem mostly occurs in traffic. I do not interact with the clutch pedal at all during this event. I do not receive any fault codes related to this problem. But I am having a hard time solving it, do you have any ideas?
@@fatihmorkoc5049 this sounds like you have an initial acceleration problem. What this means is that when you press the gas pedal there is a delay in a system causing the engine to struggle then it picks up and runs smoothly.
@@ShelDockToyotaVitz If we consider that it might be due to a delay in fuel, I experience the same shaking 1-2 seconds after putting the car in compression. Is it normal for this to happen?
@@ShelDockToyotaVitz ua-cam.com/video/UIUifoaIkfo/v-deo.html&lc=Ugx3vfOwg9OtB3Et5zB4AaABAg.AAx2ty5DZ3hABozkW-HzWA The air noise issue in this video is not present in my case, but the shaking is very similar, and it's the same engine.
@@fatihmorkoc5049 once you push the gas pedal you should hear the engine reving up very quickly when in neutral and when in gear move on the road you should hear the engine pulling very aggressively but smoothly while vehicle speed increases. If there is a struggle of the engine to keep up you most likely have a fuel problem. The fuel pump could also be a problem.
I have no fault codes, new spark plugs and cleaned throttle budy and clean MAF sensor, also tested camshaft position sensor - but still have vibration on idle and some hesitation after fast acceleration (from idle to 1500-2000 rpm)...
Depending on the age of the vehicle while can contribute to the many problems we have with Toyota vitz and other vehicles. When vibration problem exists it's also good to clean the O2 sensors and the filter is the gas tank. Sometimes the injectors require some cleaning and the EGR valve.
When vibration occurs in any vehicle it's best to do a through cleaning of the part's you mentioned and the ones I suggest. In most cases this will solve the problem.
This is good. Understanding your machine makes all he difference in getting it running at optimal performance. @shel-dock I want some clarification on the engine mount on the right. I have researched it, looking for photos and videos of how it should look, before and after it is damaged or worn out. I see the bulge at the top of yours is sunken down due to the engine weight. Mine is raised. Does that mean my mount is no longer holding the engine weight and is apparently damaged? Your response would be greatly appreciated.
Use this product to clean your throttle body. It will also clean the piston head and the spark plugs while you spray it in the throttle body while the engine is running. Do not allow the engine to die out while using the product. Use only a quarter of the can. After using the product keep the engine running about 10 to 15 minutes to blow out the liquid through the system. Click the link below. ua-cam.com/users/shorts86waCdosdew?si=QbxjZQwKNes_v0P1
If the belt is not squeaking its ok also if it does not appear to have broken groves in the belt it should be good. If the belt is not working properly the only major thing would be battery charging problems but the car would notify you of this.
Thanks for your encouraging comment. The viscosity engine oil used in this Toyota Vitz in a warm climate is 10 30. In cold to freezing climate it is best to use 5 30. 5 in this case identifying a lower viscosity.
@@ShelDockToyotaVitz not at all, i live in a really warm place usually the temp is between 29-31 all the year. I havent had any problems. Remember the engine work at the same temperature doesn’t matter how cold or hot is outside.
@@cesararturofranco9035 I agree however in my country the oil used in these cars is the 10 30. I try to find different grades but it seems this is the one available to me at all the auto shops I visit. It does not cause any effect on the vehicle so far.
My car's (vitz 2013 , 1000cc) engine runs smoothly but as i turn on the a.c it start heavy vibration. Any suggestions please. There is no electricial check light in meter.
I got a fault code saying gas pump issue causing low idle but only when the mechanic used a big computer scanner... It said the fix was to change the fuel pump... I haven't changed it though
Using a higher amperage alternator on your vehicle will not solve your engine vibration problem. Engine vibration can be caused during idling by: 1. Bad sensor (MAF or MAP), Partly blocked throttle-body valve or clogged air filter. 2. Partly blocked injector/injectors, engine bay fuel filter or fuel tank filter. 3. Bad spark plug or coil-pack. 4. Blocked or partly blocked EGR valve.
Hey I have same vitz but whenever i press any button the slight vibration is felt so its normal? And also when it’s on idle the slight vibration is felt
I have tried all the ways of stopping my 1kr to stop vibration, but all to avail. So I don't know what suppose to do next. I would be grateful if u could help🙏🙏
An actuator is any moving part that is activated electrically. Example - the injector. That part of the injector that open and close to allow fuel to pass into the combustion chamber.
My toyata yaris engine vibrate anytime I remove the battery and fix it back....especially when I stop driving or am in a traffic and I step on the brake it can vibrate. Any solution
Engine Vibration --Vibration beyond the normal throttling of the engine. This causes the body of the vehicle to shake/vibrate while the vehicle is idling or come to a complete stop. Engine vibration is caused by abnormal operation of a system or systems of the engine.
I have toyota vitz 2007 model 1kr engine, i cleaned my EGR after cleaning i face 2 issues one is vibration on idling and with AC and the 2nd is engine oil come to air filter box, i am very worried what should i do?because alotz of mechanice dont understand my problem
@@ShelDockToyotaVitz sir i am from Pakistan, here is now 31 temp, i topup my engine oil, after egr cleaning i face oil leak from valve cover(tepat cover) i replaced the cover and after replacement i see engine oil in air filter and engine leaking from valve cover too, and i face vibration in idling specially with AC
It would seem like the job was not done properly. I would bring the vehicle back to the mechanic, show him the problems you are now facing for him to resolve them. It would seem he needs to reseal some areas- things you can't do from your standpoint.
@@ShelDockToyotaVitz now i replace the valve cover, but still i saw engine oil in air filter and still facing vibration, would u recommend throttle body cleaning?or its the cause of old piston and rings?kindly help me in this matter i am worried,i can share with u my car engine video on insta of u want
@@albertkidah5013 changing the heat gasket will not help with engine vibration. Engine vibration in itself is mainly caused by oil leak either from the piston rings or valve seal or both.
My mechanic solved my vibration by increasing the power of the engine. Even though this reduced the vibration completely, my fuel consumption went up by almost 2-fold. I want to know if this is the best solution?
Increasing engine rpm to reduce engine vibration is not the solution. Find what is causing the vibration and fix it. It can be one to several problems it will take time to find them.
@@ShelDockToyotaVitz I do have problems with the accelerator when I'm driving , if am doing 50mh speed just stay there and sometime dosing speed up and when I let go of the pedal of the accelerator and put my feet back on the eccelerator then it speed up, But it keep doing the same problems when am driving,
@@ShelDockToyotaVitz I did clean throttle body and I also rev the accelerator and throttle body did open and close normal, when I taken it apart but i don't no what could be else problem.
If the vehicle is in park does the engine idle without struggling to keep up? If you press the brakes while you are in park does the engine still struggle to keep up?
hamilton try this experiment. Disconnect the hose at the brake booster. It also connects to the plastic intake close to the cylinder head. Bung the hose carefully where you disconnect it at the brake booster so that no air can enter it. Ensure the bung can't be sucked in. Start the car and drive it slowly because the brake will be very hard to press so you will need to press on it with a lot of force to stop the vehicle. When driving slowly press the brakes and see if the engine still struggles. If it does not struggle it means that you either have a vacuum leak at the hose you disconnected or you have a vacuum leak in the break buster itself.
im having toyota vitz its alway showing check light i fixed this prblm many times but its come back again... do u have any permanent solution of this prblm...
A check light will be displayed if a fault is detected by a sensor or the sensor itself is bad. There also maybe a problem with the wiring to the sensor.
I have 2010 Toyota vitz, 3 plugs with 81K mileage. Engine vibrates like it’s about to crush out when is passed 80mph, it wasn’t like that at first but can’t go above 80mph without engine shaking, got any suggestions please ? And yes it vibrates right after you turn engine on prior to turning it off but I’m more concerned about not reaching 90mph on a high way without engine shaking
When you have vibration at higher speeds it can be that you have an engine mount damage or some kind of wheel bushing problem. Check these out because engine vibration is usually reduced at higher speeds.
Bro link me please ...me Have a Belta that has a 1KR engine and I changed the right engine mount but me still a get vibration and me check light come on. Link me please ASAP so we can talk
Engine mount does not cause check light to appear. Do a scan of your vehicle to see what what is happening so you can correctly address the issue. I would recommend that persons who does some amount of repairs on their own vehicle to own a scan tool. A simple and reliable scan tool is the Blue Driver scan tool.
I have Toyota belta 1000cc Engine vibration is much high .. even all dashboard vibrate badly .. This vibration come only on idle ... When I press A little acclater it reduces ... Kindly guide me about fault ??
Thanks for your question. When there is a vibration problem with our engine and no engine check light is on then the first thing to do is to clean your throttle body. When this cleaned and if the problem persist then I will suggest other options.
Brother i have a same issue in my car now its 100 ok plz increase the race on ur car accelarator ok and this mechanic is getting totally wrong 8nformation etc
Clean the throttle with wd40 or carbcleaner. also clean air jet nozzles of the throttle apply some stream of carbleaner then apply steam of pressurized air on them. Before dismantling throttle body disconnect mass wire off the battery. Then disconnect throttle body harness.
This is because anything that uses electrical current add load to the alternator. This load stress the alternator causing it to also stress the engine. This stress (load) reduces engine speed (rpm) causing engine vibration. This though is as a result of a problem developing or is alresdy there with some kind of mechanical device no working properly.
When there is a mechanical problem causing engine vibration then you will need to check all the potential parts that can be the problem causing your engine vibration.
If engine check light is off then a mechanical device is not working properly. One of the first stage of correcting engine vibration is to thoroughly clean your throttle body and valve.
Engine vibration can be as a result of many single or multiply issues. Please check out this video below, its not much but it discusses many of the causes that results in engine vibration. ua-cam.com/channels/MqZwBG19XelNEVJfLVclRg.htmlvideos
When you remove the air intake cover exposing the throttle body at the top look in the hole of the throttle and the partly round metal that you see blocking the hole is the throttle body valve.
@@corletterichards5034 one system fixed will not solve this problem there are a number of things you need to do. 1. Clean spark plugs 2. Clean oxygen sensors 3. Clean EGR valve 4. Clean fuel filter in fuel tank. 5. Clean throttle body valve
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Just managed to clean the throttle body from throttle body cleaner works really well. Thank you Sir
This is a very informative video and actually clears up a lot of things about this vehicle, thanks a lot for taking the time to study this car model and letting us know your experience.
Thanks for your up building comment.
good keep it up
Shel ....Thanks for your update. very happy you keep doing this. This is because in my country, this vehicle is very popular especially from 2006 to 2012. Our major drawback with this is vehicle is the fact that Toyota did not sell these vehicles here because we drive on the left. This means its shipped as right hand and when it arrives our locals cut and switch the dash and steering with a few cosmetic touch. It makes it hard sometimes to troubleshoot electrical at this point as some sensors or fault indicators may be disconnected or removed completely. your video however has helped many here who were lucky it was just the throttle body and not electrical. thanks again
Thanks for you positive review of my content. I appreciate all those who view these presentations and use as is appropriate. Thanks again.
Thank God I found a Ghanaian here. Please my mechanic tried solving my vibration issue by increasing the power of the engine (Known locally in twi as "wamma gya no k) soro"). Please is that the best solution or you think cleaning the throttle body will do the work for me. (I don't have any indicators on my dashboard showing that it is electrical fault, so I think its not an electrical fault)
@@OldhamLab it is very bad solution as you are just increasing your engine idle rpm, to compensate the vibration, at the long-term you radiator will come on more often as the Engine may heat up quickly. Take note your Engine idle for this type of cars should be approx. 780rpm. Some of the vitz don't have that screw you talking about, I cannot actually tell from which year. I'll advise to check your air flow systems, plugs, throttle body cleaning, and fuel injectors.
@@Donelio0202 Thanks so much
Very informative video i have exactly the same problem on my car and show the car to many mechanic but now i really understand thanks ,,,
Yes Sir,Yard man talking Yuh big ups unno self sameway reporting from Ghana.
Great video, this cleared up my vibration issue. Thanks a lot
My pleasure to help.
Excellent you know what your talking about.
yeah man. Good video, big up yuself
How can fix the vibrations problem
Can you do a video on 3zr-fe
good to know that your problem is solved, mine comes back after about a month of cleaning throttle body and fuel injector. After how long do you clean both of these culprits?
Do you feel any lost or reduced power at any time during acceleration?
@@ShelDockToyotaVitz That is the thing, its perfectly fine while running, only problem is while idling.
While your engine is running pull out each coil pack and hold it just above the spark plug then listen to the sound of the arcing of each coil pack as you do this to ensure the ticking arcing sound is similar for each coil pack.
+255789170295
Throttle body cleaned.
Solenoid cleaned.
PCV valve cleaned.
Engine mounts replaced.
Ignition coils checked with a multimeter.
Spark plugs inspected.
MAF sensor cleaned.
My car is a 2013 Toyota Auris 1.33 Gasoline. While driving in traffic, I experience an annoying shaking when I first press the gas pedal and then when I release it again. This problem occurs in every gear, but is less noticeable in higher gears. I don't think this is an ignition problem. There is no mechanical noise coming from my car when this happens, logic leads me to believe that this is not a mechanical problem. Sometimes my car works very smoothly. The problem mostly occurs in traffic. I do not interact with the clutch pedal at all during this event. I do not receive any fault codes related to this problem. But I am having a hard time solving it, do you have any ideas?
@@fatihmorkoc5049 this sounds like you have an initial acceleration problem. What this means is that when you press the gas pedal there is a delay in a system causing the engine to struggle then it picks up and runs smoothly.
Sometimes this delay can be as a result of the engine not getting enough fuel during this initial press of the gas pedal.
@@ShelDockToyotaVitz If we consider that it might be due to a delay in fuel, I experience the same shaking 1-2 seconds after putting the car in compression. Is it normal for this to happen?
@@ShelDockToyotaVitz ua-cam.com/video/UIUifoaIkfo/v-deo.html&lc=Ugx3vfOwg9OtB3Et5zB4AaABAg.AAx2ty5DZ3hABozkW-HzWA
The air noise issue in this video is not present in my case, but the shaking is very similar, and it's the same engine.
@@fatihmorkoc5049 once you push the gas pedal you should hear the engine reving up very quickly when in neutral and when in gear move on the road you should hear the engine pulling very aggressively but smoothly while vehicle speed increases. If there is a struggle of the engine to keep up you most likely have a fuel problem. The fuel pump could also be a problem.
Excellent explanation 👌 👏🏽
Thanks bro.
Very well explained for my for vehicle thank you.
I had same problem and check out. it turns out to be the idle control valve was blocked. There was no check light on dashboard.
very helpful content
I have no fault codes, new spark plugs and cleaned throttle budy and clean MAF sensor, also tested camshaft position sensor - but still have vibration on idle and some hesitation after fast acceleration (from idle to 1500-2000 rpm)...
Depending on the age of the vehicle while can contribute to the many problems we have with Toyota vitz and other vehicles. When vibration problem exists it's also good to clean the O2 sensors and the filter is the gas tank. Sometimes the injectors require some cleaning and the EGR valve.
When vibration occurs in any vehicle it's best to do a through cleaning of the part's you mentioned and the ones I suggest. In most cases this will solve the problem.
@@ShelDockToyotaVitz thanx
Hello, i have a toyota vitz car year 2010 and i notice that in the dashboard it appears "P67-Y". Can someone tell me what is it ? Thank you
justamenteme pasa ese problema, en cambio el mio de de 4 pistones, desde que apago el aire se va el sonido y es muy molestoso en verdad
I have rs vitz Japanese vehicle year 2005 the transmission having a honoring noise what could be the problem
Have you changed your transmission fluid since you bought the vehicle and how recently was this?
What fan belt number do u use
Thanks it very useful information
this vehicles are knows for knocking/pinging sound issue up hill or on load acceleration, do you know any solution for such..?
Try getting a cleaning cleaning of deposits in the combustion chamber
Clean carbon buildup on pistons
Vacuum solenoid, injectors, oil change, fuel pump/ fuel filter.
Can you use 4 cylinders for a 3cylinder vehicle
This is good. Understanding your machine makes all he difference in getting it running at optimal performance. @shel-dock I want some clarification on the engine mount on the right. I have researched it, looking for photos and videos of how it should look, before and after it is damaged or worn out. I see the bulge at the top of yours is sunken down due to the engine weight. Mine is raised. Does that mean my mount is no longer holding the engine weight and is apparently damaged? Your response would be greatly appreciated.
Didn't think about looking at that but I will check it out and give you a response. Thanks for the request.
Does this also work on a 4 cylinder engine. ( 4 plugs)
Use this product to clean your throttle body. It will also clean the piston head and the spark plugs while you spray it in the throttle body while the engine is running. Do not allow the engine to die out while using the product. Use only a quarter of the can. After using the product keep the engine running about 10 to 15 minutes to blow out the liquid through the system. Click the link below.
ua-cam.com/users/shorts86waCdosdew?si=QbxjZQwKNes_v0P1
Do you think an old serpentine belt on the alternator can contribute to the vibration?
If the belt is not squeaking its ok also if it does not appear to have broken groves in the belt it should be good.
If the belt is not working properly the only major thing would be battery charging problems but the car would notify you of this.
very informative video. thumbs up!
what viscosity oil is recommended for this vehicle 1KR-FE (180,000km mileage)?
Thanks for your encouraging comment.
The viscosity engine oil used in this Toyota Vitz in a warm climate is 10 30. In cold to freezing climate it is best to use 5 30.
5 in this case identifying a lower viscosity.
My car has 175000km and i still using 0w20. Always use what the manufacture recommend
@@cesararturofranco9035 The grade motor oil always depends on the climate condition. Where I live is is usually warm.
@@ShelDockToyotaVitz not at all, i live in a really warm place usually the temp is between 29-31 all the year. I havent had any problems. Remember the engine work at the same temperature doesn’t matter how cold or hot is outside.
@@cesararturofranco9035 I agree however in my country the oil used in these cars is the 10 30. I try to find different grades but it seems this is the one available to me at all the auto shops I visit.
It does not cause any effect on the vehicle so far.
Cluster showing p67-z even when the car the off, any reason why its popping up??
My car's (vitz 2013 , 1000cc) engine runs smoothly but as i turn on the a.c it start heavy vibration. Any suggestions please.
There is no electricial check light in meter.
This means that some parts need cleaning such as:
1. Throttle body
2. EGR valve
3. MASS airflow sensor
I got a fault code saying gas pump issue causing low idle but only when the mechanic used a big computer scanner... It said the fix was to change the fuel pump... I haven't changed it though
Happy that at least you know exactly the problem.
@@ShelDockToyotaVitz I haven't changed it because I don't want to waste my money... It's amazing how just cleaning ur valve fixes it but not for us
Can we use high amp alternator
Using a higher amperage alternator on your vehicle will not solve your engine vibration problem. Engine vibration can be caused during idling by:
1. Bad sensor (MAF or MAP), Partly blocked throttle-body valve or clogged air filter.
2. Partly blocked injector/injectors, engine bay fuel filter or fuel tank filter.
3. Bad spark plug or coil-pack.
4. Blocked or partly blocked EGR valve.
Hey
I have same vitz but whenever i press any button the slight vibration is felt so its normal?
And also when it’s on idle the slight vibration is felt
Once it's slight and recover quickly so that it's hardly noticeable if you are not paying attention to it that good.
I have tried all the ways of stopping my 1kr to stop vibration, but all to avail. So I don't know what suppose to do next. I would be grateful if u could help🙏🙏
Do you have any check engine light on?
What is Activatour you sed if activator not work properly ans me plz
An actuator is any moving part that is activated electrically. Example - the injector. That part of the injector that open and close to allow fuel to pass into the combustion chamber.
Which other car altinator you think can work this that engine?
The alternator is not the problem. Once you get the engine vibration under control everything will run smoothly.
@@ShelDockToyotaVitz I know. I'm just wondering if another car altinator can fit it.
Most Toyota vehicles either sedans or hackbacks will have the same type of alternator. They must be within a certain year group though.
My toyata yaris engine vibrate anytime I remove the battery and fix it back....especially when I stop driving or am in a traffic and I step on the brake it can vibrate. Any solution
Same issue in my car😔
Anytime you remove your battery terminals or battery always stsrt the car after it is replaced and leave it for about 5 to 10 minutes before driving.
Anytime you remove the battery you need to do a idle relearn procedure. Learn it on youtube,
bro how did you solve your problem
Hi , my engine is losing power completely barely 10% power will be left when going uphill cant manage 130° uphill also . What might be the problem 😳
Do you have any check engine light on? With these new vehicles the first thing you do is a scan when something is wrong.
Do a scan first.
With these new vehicles when anything is wrong with it a scan is the first thing to do.
How's the exhaust if it's blocked you lose a power going uphill
What exactly you mean by engine vibration?
Engine Vibration --Vibration beyond the normal throttling of the engine. This causes the body of the vehicle to shake/vibrate while the vehicle is idling or come to a complete stop.
Engine vibration is caused by abnormal operation of a system or systems of the engine.
I have toyota vitz 2007 model 1kr engine, i cleaned my EGR after cleaning i face 2 issues one is vibration on idling and with AC and the 2nd is engine oil come to air filter box, i am very worried what should i do?because alotz of mechanice dont understand my problem
Check your engine oil level to see if it is below maximum.
Which country do you live and what is the climate at this time?
@@ShelDockToyotaVitz sir i am from Pakistan, here is now 31 temp, i topup my engine oil, after egr cleaning i face oil leak from valve cover(tepat cover) i replaced the cover and after replacement i see engine oil in air filter and engine leaking from valve cover too, and i face vibration in idling specially with AC
It would seem like the job was not done properly. I would bring the vehicle back to the mechanic, show him the problems you are now facing for him to resolve them. It would seem he needs to reseal some areas- things you can't do from your standpoint.
@@ShelDockToyotaVitz now i replace the valve cover, but still i saw engine oil in air filter and still facing vibration, would u recommend throttle body cleaning?or its the cause of old piston and rings?kindly help me in this matter i am worried,i can share with u my car engine video on insta of u want
I did change the gasket but then started shaking and im seeing the engine light on
@@albertkidah5013 changing the heat gasket will not help with engine vibration. Engine vibration in itself is mainly caused by oil leak either from the piston rings or valve seal or both.
My mechanic solved my vibration by increasing the power of the engine. Even though this reduced the vibration completely, my fuel consumption went up by almost 2-fold. I want to know if this is the best solution?
Increasing engine rpm to reduce engine vibration is not the solution. Find what is causing the vibration and fix it. It can be one to several problems it will take time to find them.
@@ShelDockToyotaVitz Thank you
Today, my mechanic removed and cleaned the IAC valve. After starting the engine, the "Check engine" sign appeared on the dashboard, how do I fix that?
You can remove a check engine light by using a scan tool, however if the problem is still there the check engine light will re-appear.
hi I got same engine, but when I drive it won't give more power and something give power, do you no any problems with this please
Is this a problem that recently came up or you got the vehicle with the problem
@@ShelDockToyotaVitz I do have problems with the accelerator when I'm driving , if am doing 50mh speed just stay there and sometime dosing speed up and when I let go of the pedal of the accelerator and put my feet back on the eccelerator then it speed up, But it keep doing the same problems when am driving,
@@ShelDockToyotaVitz more like it not getting air and engine struggling to speed up
@@ShelDockToyotaVitz I did clean throttle body and I also rev the accelerator and throttle body did open and close normal, when I taken it apart but i don't no what could be else problem.
@@killapakiz786 it seems that you have an electrical problem.
My vitz turn off when I stop I break especially in traffic, any suggestion?
Does the engine struggle to keep up every time you slow down by pressing the brakes.
If the vehicle is in park does the engine idle without struggling to keep up?
If you press the brakes while you are in park does the engine still struggle to keep up?
Yes the engine struggle when apply breaks when it's in moations and it does not happen when in park.
Where in JA are you located?
hamilton try this experiment. Disconnect the hose at the brake booster. It also connects to the plastic intake close to the cylinder head. Bung the hose carefully where you disconnect it at the brake booster so that no air can enter it. Ensure the bung can't be sucked in.
Start the car and drive it slowly because the brake will be very hard to press so you will need to press on it with a lot of force to stop the vehicle. When driving slowly press the brakes and see if the engine still struggles. If it does not struggle it means that you either have a vacuum leak at the hose you disconnected or you have a vacuum leak in the break buster itself.
im having toyota vitz its alway showing check light i fixed this prblm many times but its come back again...
do u have any permanent solution of this prblm...
A check light will be displayed if a fault is detected by a sensor or the sensor itself is bad. There also maybe a problem with the wiring to the sensor.
smart
I have 2010 Toyota vitz, 3 plugs with 81K mileage. Engine vibrates like it’s about to crush out when is passed 80mph, it wasn’t like that at first but can’t go above 80mph without engine shaking, got any suggestions please ?
And yes it vibrates right after you turn engine on prior to turning it off but I’m more concerned about not reaching 90mph on a high way without engine shaking
When you have vibration at higher speeds it can be that you have an engine mount damage or some kind of wheel bushing problem. Check these out because engine vibration is usually reduced at higher speeds.
@@ShelDockToyotaVitz okay, will do. Thank you.
Bro link me please ...me
Have a Belta that has a 1KR engine and I changed the right engine mount but me still a get vibration and me check light come on. Link me please ASAP so we can talk
Engine mount does not cause check light to appear. Do a scan of your vehicle to see what what is happening so you can correctly address the issue.
I would recommend that persons who does some amount of repairs on their own vehicle to own a scan tool. A simple and reliable scan tool is the Blue Driver scan tool.
I have Toyota belta 1000cc Engine vibration is much high .. even all dashboard vibrate badly ..
This vibration come only on idle ... When I press A little acclater it reduces ... Kindly guide me about fault ??
Thanks for your question. When there is a vibration problem with our engine and no engine check light is on then the first thing to do is to clean your throttle body. When this cleaned and if the problem persist then I will suggest other options.
I have a same problem i clean allbutterfly cleaning all plugs changhe fuel pump but stiil this problem
Brother i have a same issue in my car now its 100 ok plz increase the race on ur car accelarator ok and this mechanic is getting totally wrong 8nformation etc
Clean the throttle with wd40 or carbcleaner. also clean air jet nozzles of the throttle apply some stream of carbleaner then apply steam of pressurized air on them. Before dismantling throttle body disconnect mass wire off the battery. Then disconnect throttle body harness.
Which model?
1KR-FE 1000cc
if u know plz inform mn
how can i fix chk light permanantly
How old is your vehicle?
gud keep it up
What's the problem when car vibrates as soon as you touch any electric system
This is because anything that uses electrical current add load to the alternator. This load stress the alternator causing it to also stress the engine. This stress (load) reduces engine speed (rpm) causing engine vibration.
This though is as a result of a problem developing or is alresdy there with some kind of mechanical device no working properly.
@@ShelDockToyotaVitz so How Do you get rid of this problem? What are the potential causes ? Can you Redirect me in right direction?
If your engine check light if off then your engine vibration is because of a mechanical problem.
When there is a mechanical problem causing engine vibration then you will need to check all the potential parts that can be the problem causing your engine vibration.
I have a Toyota Passo 2010 same three cylinders I'm experiencing vibration
If engine check light is off then a mechanical device is not working properly. One of the first stage of correcting engine vibration is to thoroughly clean your throttle body and valve.
Okay good thank you
How can I clean them
@@ShelDockToyotaVitz I clean the throttle body , I'm wondering if I should get 3 new coil pack
@@grimmyboss2079 If your coil pack is working, it should be fine. You may only need to clean its connected terminals.
There's no MAF in this model, instead there's MAP
It is a MAF sensor. Not a MAP sensor
@@MusaHaroon-ni8nw it's MAP bro, manifold absolute pressure.
Its a MAP toyota data
👍👍👍
I have done all but still vibrating
Engine vibration can be as a result of many single or multiply issues. Please check out this video below, its not much but it discusses many of the causes that results in engine vibration.
ua-cam.com/channels/MqZwBG19XelNEVJfLVclRg.htmlvideos
Upgrade ur engine and gear box
Where is the throttle body valve located
When you remove the air intake cover exposing the throttle body at the top look in the hole of the throttle and the partly round metal that you see blocking the hole is the throttle body valve.
Evap system common failure
Sheldock why am I smelling gas from the exhaust
Check your injectors they may need changing. Too much fuel entering the combustion chamber through leaking injectors.
This is helpful
We lent
I need to take my car to you
What kind of problem your vehicle is having.
@@ShelDockToyotaVitz thanks for responding terrible vibration
@@corletterichards5034 one system fixed will not solve this problem there are a number of things you need to do.
1. Clean spark plugs
2. Clean oxygen sensors
3. Clean EGR valve
4. Clean fuel filter in fuel tank.
5. Clean throttle body valve
Ok bless up
It exactly like my car did
Where r you
Jamaica
@@ShelDockToyotaVitz how can I contact you to check my car please help having vibration no one seems to understand it
@@ladystorm6137 Get someone to scan your vehicle for any errors of your sensors and then we can start from there.
Also in Jamaica have a vitz do you work on them?
pedal
Please hellp me
Am pleased to help, what assistance can I give.
Thanks for sharing I have same problem with my car. can i have your email please
Awesome bro