Have one of these in a basher plane. It is great to help when teaching people to fly. Really takes away the fear of overdoing controls......and leading to horrific horrible crashes
Looking forward to your video on the A3 Super 3. I just took delivery on mine yesterday. I have not seen any videos on the new computer software. Thanks so much. You are a great asset to the RC community.
Hello & good morning from Dallas, Texas..... thank you for the decal/keep calm note via Royal Mail Stamp. It was a thoughtful gesture from a class act..... Very professional indeed.
Great video, very clear. Having setup a few of these for friends it might be worth showing how a 'badly' configured install will react in different modes. The limited movement and slow responses in some modes often surprises people too. I'm also not a great fan of leaving the master gain on the transmitter (too easy to move/fiddle accidentally). Once determined it's safer to apply to the stabiliser and disable the channel.
This device seems to be a stripped down version of the MicroBeast Flybarless controller I installed in my Trex Dominator 470L. If you're into Helis you should checkout the MicroBeast it is quite an amazing device and like the Hobby Eagle almost all the mixing is done in the controller. Great Video, thanks.
I learned to fly helicopters using Co-Pilot. It was a system that used an infrared sensor that monitored temperature gradient by looking at the horizon. It's bullet proof.
@@cmulder002 actually, I have. Over an ice skating rink too. A frozen lake. LOTS of night flying. In winter and summer. Indoors too. It's always done fine. In fact, you can orient the sensor right side up or down. It figures it out. It's got an aerobatic mode too. And even does VTOL.
@@cmulder002 It describes any fixed wing aircraft with "Vertical Take Off/Landing capability. Like the Harrier Jump Jet or F-35. There is also a STOL designation for Short Take Off/Landing capability. This is what the British Aircraft carriers do with the Harriers. They use a short deck with a "ski jump" on it that helps a heavily loaded Harrier get into the air without the need of a catapult.
Hello what do you think are the best settings for the 1,5m eflight cirrus? Im beginner and wanna fly relaxed so i need very beginner settings... Can u help me?
Lee I'm setting up a a3 v2 and everything works correct apart from the rudder and elevator,the rudder moves when the elevator should and visa versa,is there away to correct this.thnx
Thanks! My first time setting up a stabiliser, so this was a good vid for me. I don't understand the three-way input, it must be automatic, altho' my stabiliser has four, not three settings? Also, the slot heads on the individual gains are poor quality - a nightmare to adjust. The tip about setting up in 3D was great , as was the 'reversing' that followed! Thanks again.
Again and as always great video and explanation. Just a question to see if it is clear to me, if you have a dual rates plane and expo, all that should be eliminated? Thank you.
Thanks for this Painless!! I'm looking at putting this in a warbird, just to help with Wind, in normal mode it's not like auto level where you have to hold the plane into a bank is it? I'm not a fan of horizon type modes, just would like a little AS3X like action without a $100+ receiver
Bother! I now have a continuously flashing red light? I can move from it into the 'selection box' , but when I try to get out of that, it goes back to a continuous flashing red light. This isn't mentioned in any manual or video, and I'm a bit stuck? Help?
Hi, I'd like to have this kind of thing in my kingfisher. Is there a special tip to know with the flaps? thanks for all yours very clear and informatives vids.
Good day sir Did you make a video on setting up the other 2 stabilizers ? Reason why I ask because the videos of “capt” Brian are not always accurate , systematic and clear enough (as is the case in the videos linked ). I am interested in the A3 pro setup. I would like to take this opportunity to thank you for your great videos that offer priceless information that would take people a lifetime to figure out or learn on their own. Thank you
Thanks for this Painless. Exactly what I was looking for. Just ordered the Pro version. Just one question... I need this because I'm new to this fixed wing stuff and not at all sure I can fly a wing in 'rate' mode. You mention to add the stabiliser after flying, checking and trimming the wing. Trouble is it'll probably be smashed into a million little bits of EPP by then with my skills.😀 How would you approach my dilemma?
For your first flight it's better to take off with the gyro off, gain some height and then flip the switch to see how the plane responds. You've bought the Pro version which has extra features such as Level Calibration which need to be set correctly as in the 'safe' modes such as Trainer mode stick movements will be moderated.
Thanks. I have been using an A3 pro with a Spektrum radio and the mess of all the wires. I just got a Q X7 last week and set the default order as TAER. So I just changed it back to AETR as it seems that will makes things easier in the future.
The setup and adding of channels in OpenTX is a common thing so check out my OpenTX mix school playlist for how to do it.. I also have a QX7 playlist too.. best of luck!
Do you see any benefit of the basic version over the S6R/S8R? I set up an S6R recently in a Bonsai wing and it works very well, especially launching in takeoff mode. Have ordered a second for a bigger wing I have .
I'm not a fan of the SxR receivers. I made the videos on getting them to work as Frsky had made such a mess of the documentation and so many pilots were damaging planes. When setup they work well. I've used lots and non yet offer the perfect storm of ease and powerful features - yet! Adding a flight controller seems to be the goto for me.. Horses for courses..
hi i have the A3-LV2 and cant get it to work at all first problem was no control to tx them when it did come on it but my plane into a mad like delta helly mix sticks all over . do you have to add this to a new receiver ie not been bind great video would rely love some help cheers from newcastle
All of the steps are in the video. I made a playlist for all three of them. I'm not following what you're actual issue is but all I did to set mine up is in here.. best of luck!
Is there any reason you chose to run this instead of Matek F411-WING Flight Control I ordered this for my Sonic mini wing and then discovered the Matek flight controller, seems to be a better option kinda wish I would have purchased that instead.
These videos are made to show how to setup the technology. It pays to do your homework before taking the plunge. I did a video on it Fixed Wing and Planes 101: Stabiliser or flight controller? ua-cam.com/video/YAfNC55Udu0/v-deo.html
hi i have a problem with a3 all fine, but rudder is not going down than i move stick down on remote ? is ist normal may be ? another ele and ail ok (full period).
Have one of these in a basher plane. It is great to help when teaching people to fly. Really takes away the fear of overdoing controls......and leading to horrific horrible crashes
Yeah i have the super3 it was in my T-28 V2 but i no longer use it :)
Looking forward to your video on the A3 Super 3. I just took delivery on mine yesterday. I have not seen any videos on the new computer software. Thanks so much. You are a great asset to the RC community.
Hello & good morning from Dallas, Texas..... thank you for the decal/keep calm note
via Royal Mail Stamp. It was a thoughtful gesture from a class act.....
Very professional indeed.
Great video, very clear. Having setup a few of these for friends it might be worth showing how a 'badly' configured install will react in different modes. The limited movement and slow responses in some modes often surprises people too.
I'm also not a great fan of leaving the master gain on the transmitter (too easy to move/fiddle accidentally). Once determined it's safer to apply to the stabiliser and disable the channel.
This device seems to be a stripped down version of the MicroBeast Flybarless controller I installed in my Trex Dominator 470L. If you're into Helis you should checkout the MicroBeast it is quite an amazing device and like the Hobby Eagle almost all the mixing is done in the controller. Great Video, thanks.
Keith Kamps have you installed the L version?
I have the A3 super 3 and have not installed it yet because I didn't know the functionality of it until now. Thanks!
I learned to fly helicopters using Co-Pilot. It was a system that used an infrared sensor that monitored temperature gradient by looking at the horizon. It's bullet proof.
Ah you never flew it above snow then ;) it assumes the sky is colder then the ground but that is not always the case ;)
@@cmulder002 actually, I have. Over an ice skating rink too.
A frozen lake.
LOTS of night flying. In winter and summer.
Indoors too.
It's always done fine.
In fact, you can orient the sensor right side up or down.
It figures it out.
It's got an aerobatic mode too.
And even does VTOL.
What do you mean with "VTOL" ? all helicopters can take off vertical (its there "thing" what sets them apart from fixed wing ;)
@@cmulder002 It describes any fixed wing aircraft with "Vertical Take Off/Landing capability.
Like the Harrier Jump Jet or F-35.
There is also a STOL designation for Short Take Off/Landing capability.
This is what the British Aircraft carriers do with the Harriers. They use a short deck with a "ski jump" on it that helps a heavily loaded Harrier get into the air without the need of a catapult.
clever bit of kit
How I can put a3v2 gyro in my flying wing , what setup I need ?
Please reply ❤️
I've used all of the others. The setups are very similar
Best of luck
Hello what do you think are the best settings for the 1,5m eflight cirrus? Im beginner and wanna fly relaxed so i need very beginner settings... Can u help me?
love this Stabiliser evan makes me look good lol
Lee I'm setting up a a3 v2 and everything works correct apart from the rudder and elevator,the rudder moves when the elevator should and visa versa,is there away to correct this.thnx
Sounds like either the input channel's are in the wrong order or the servo on connected to the wrong outputs... Best of luck
Thanks! My first time setting up a stabiliser, so this was a good vid for me. I don't understand the three-way input, it must be automatic, altho' my stabiliser has four, not three settings? Also, the slot heads on the individual gains are poor quality - a nightmare to adjust. The tip about setting up in 3D was great , as was the 'reversing' that followed! Thanks again.
Again and as always great video and explanation.
Just a question to see if it is clear to me, if you have a dual rates plane and expo, all that should be eliminated?
Thank you.
I can not use a stabilizer with the receiver I just bought because there not made by the same manufacturer
Thats should not matter. Best of luck
Is it like quads?WAY funner without stability if so.I don't want stabilization
Depends on the model ;) There is such a thing as 'scale models' in the world of fixed wing...
What if i want to use double servo,s for aileron or elevator and not Y-cable? I'm stuck with a Y-cable?
Thanks for this Painless!! I'm looking at putting this in a warbird, just to help with Wind, in normal mode it's not like auto level where you have to hold the plane into a bank is it? I'm not a fan of horizon type modes, just would like a little AS3X like action without a $100+ receiver
Looks fantastic, Lee. But... You think it's easier to use one of those instead of a S6R, for example?
So much easier IMHO..
I gave up on the S6R and although I haven’t used this type, I have used an alternative and it was so much easier.
@@kevalinopicks5555 Nice, thanks! 😊
Very good Thank you.
Bother! I now have a continuously flashing red light? I can move from it into the 'selection box' , but when I try to get out of that, it goes back to a continuous flashing red light. This isn't mentioned in any manual or video, and I'm a bit stuck? Help?
I’ve not seen that - I’d let the vendor know.. best of luck!
Oh, and thanks for the excellent video
Hi Painless Any idea on setting this on a Horus with a delta wing it just will not work correctly
Hi guys...
how to rdevice reset for a3v2?
No idea sorry. Best of luck with it!
Hi, I'd like to have this kind of thing in my kingfisher. Is there a special tip to know with the flaps? thanks for all yours very clear and informatives vids.
Not sure, I don't use it much here. I prefer the more advanced one.. Best of luck with it! :D
@@Painless360 thanks ! best regards from France :-)
Good day sir
Did you make a video on setting up the other 2 stabilizers ?
Reason why I ask because the videos of “capt” Brian are not always accurate , systematic and clear enough (as is the case in the videos linked ). I am interested in the A3 pro setup.
I would like to take this opportunity to thank you for your great videos that offer priceless information that would take people a lifetime to figure out or learn on their own.
Thank you
I’m planning those videos in the New Year. The setup is very similar, the manuals are well laid out too. Thanks for the comment, seasons greetings!
Will it work with fsia6b receiver
Thanks for this Painless. Exactly what I was looking for. Just ordered the Pro version.
Just one question... I need this because I'm new to this fixed wing stuff and not at all sure I can fly a wing in 'rate' mode. You mention to add the stabiliser after flying, checking and trimming the wing. Trouble is it'll probably be smashed into a million little bits of EPP by then with my skills.😀 How would you approach my dilemma?
It should still work but the model needs to be well setup too.. best of luck!
For your first flight it's better to take off with the gyro off, gain some height and then flip the switch to see how the plane responds. You've bought the Pro version which has extra features such as Level Calibration which need to be set correctly as in the 'safe' modes such as Trainer mode stick movements will be moderated.
How does it know what channel order you picked in your transmitter?
It's set. That's why you need the order I show in the video.. Best of luck
Thanks. I have been using an A3 pro with a Spektrum radio and the mess of all the wires. I just got a Q X7 last week and set the default order as TAER. So I just changed it back to AETR as it seems that will makes things easier in the future.
Any possibility of doing a video not using s-bus and on a taranis q? I'm stuck!
Thanks
Hi lee, can you use these units with a servo on each aileron ? I see there’s only one servo output. Thanks, Mark
Not easily, see my videos on the more advanced stabilisers that support it.. Best of luck!
Hi,any possible of showing how to configure the channels on a taranis q7
Thanks
The setup and adding of channels in OpenTX is a common thing so check out my OpenTX mix school playlist for how to do it.. I also have a QX7 playlist too.. best of luck!
Hello quick question. Where does the condenser plug into for the hobby wing a3 I stabilizer? Thanks
In any of the spare outputs.. See the manual. Best of luck!
What’s happened to your hand guru 360? Hope it’s not a prop strike?? 😉
I think it is a prop strike. I hope its healing well for him.
Do you see any benefit of the basic version over the S6R/S8R? I set up an S6R recently in a Bonsai wing and it works very well, especially launching in takeoff mode. Have ordered a second for a bigger wing I have .
I'm not a fan of the SxR receivers. I made the videos on getting them to work as Frsky had made such a mess of the documentation and so many pilots were damaging planes. When setup they work well. I've used lots and non yet offer the perfect storm of ease and powerful features - yet! Adding a flight controller seems to be the goto for me.. Horses for courses..
@@Painless360 Agree. I couldn't have got my S6R working without your fantastic videos. Thanks!
hi i have the A3-LV2 and cant get it to work at all first problem was no control to tx them when it did come on it but my plane into a mad like delta helly mix sticks all over . do you have to add this to a new receiver ie not been bind great video would rely love some help cheers from newcastle
All of the steps are in the video. I made a playlist for all three of them. I'm not following what you're actual issue is but all I did to set mine up is in here.. best of luck!
@@Painless360 hi thanks dont no whats going on it mite be a bad receiver but great video and thanks
👽👽👽👽👽👽👽👽👽
UFO in background at 8.43 😎
Is there any reason you chose to run this instead of Matek F411-WING Flight Control I ordered this for my Sonic mini wing and then discovered the Matek flight controller, seems to be a better option kinda wish I would have purchased that instead.
These videos are made to show how to setup the technology. It pays to do your homework before taking the plunge. I did a video on it Fixed Wing and Planes 101: Stabiliser or flight controller? ua-cam.com/video/YAfNC55Udu0/v-deo.html
You lost me at S-Bus! I have Hitec Aurora 9 and Optima receivers.
ua-cam.com/video/GbUMC8h2uhU/v-deo.html
Please can You say me if this A3 Pro Version is compatible to a Spektrum Ar 8000 Receiver ..??
I've not tried it but I can't see why not - I'd check with the vendor before hitting the buy button..
Does it works with nitro planes AND gas planes
I only fly electrics so can't comment. I'd expect so but you'd have to make it as smooth as you could..
hi i have a problem with a3 all fine, but rudder is not going down than i move stick down on remote ? is ist normal may be ? another ele and ail ok (full period).
The Rudder shouldn't go down, the Rudder should move from side to side. I double check your connections. Best of luck!
@@Painless360 eleron
rear stabilizator
Horizontal or vertical rear stabiliser? Sorry, I'm really not following what you are describing..
@@Painless360 horizontal
Will this work with Frsky sbus or crossfire sbus? Thanks.
Check out the Rx I’m using in the video ;) Happy flying!
Have you made the video of the A3 Pro? Cannot find it...
Not yet..
@@Painless360 Ok, it would be interesting to see how different they are from the A3 and A3L.
What raido are you yousing
FrSky X-lite, see my series on it...
As a beginner is it worth the extra for the pro?
Any stabiliser that includes an auto-level function is a nice idea when you're learning to fly. Happy flying!
does this work with ibus
I don't remember seeing that at the manual... might be worth a check.. best of luck!
Was interested until Motionrc wanted £11.66 postage on a £25 item! Forget it!
I'll use a Frsky S8R which includes an Rx for around the same price.
Checked eBay? :)
And (I hate to say it) Banggood.
Originally I trusted you and just followed your link! :-))
And thanks for the heads up on ebay. And many thanks for all your other informative videos.
And I hate to say that I probably use Banggood more than I should! And thanks for the reply.