Woodland Mills WC68 Step by Step assembly.
Вставка
- Опубліковано 29 сер 2024
- This video is a step by step assembly and unboxing of a Woodland Mills WC68 wood chipper. I will also be running it on a Kubota B2601. The WC68 is rated for 20-50HP. The b2601 is 19.5HP at the PTO. Woodland mills confirmed 19.5 is enough PTO HP to run it.
This video is for entertainment purposes only. #kubota #b2601 #woodlandmills #wc68
DISCLAIMER:
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
By using some of the affiliate links above, I may receive a small commission, at no extra cost to you. This is the easiest way to support me and helps me continue making content like this for you. Thank you 🙏
Due to factors out of my control, I cannot guarantee against improper use or unauthorized modifications of this information. I assume no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. I recommend safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not me. Be safe!
Thanks for watching! Please help out the channel by hitting the subscribe button and giving the video a thumbs up!
Nice video. Assembly is tomorrow. Thanks.
You are going to enjoy using the chipper. Thanks for watching the video!!! Happy chipping 😁👍🚜💨☀️
Thank you so much for this video. The tips on taking off the PTO shaft cover and trimming advice was very helpful. The manual doesn’t say how to remove the cover 👍😎
Your welcome thanks for checking out the video. Have fun chipping 😁👍🚜💨🍳 If your red handle goes into neutral a lot check out the comments there is a way to adjust the relief valve.
MJA doing stuff I will check back if the handle goes into neutral. I’m currently trying to figure out the correct shaft length. I measured 28.5 between chipper and PTO gear grooves . I measured 29-7/16 between the PTO shafts push buttons. This gives me a 15/16 difference + 1 tells me to cut 1-15/16. When I put the shaft back together for install it is too long, even if I allow the PTO shaft slip past the groove for extra length. I’m going to call Woodland Mills today for help. The two sides of the shaft overlap and basically butt up against themselves. I believe I need a gap in the overlap to see a space, so if I hit a bump there is give and the butter up metal won’t jam against the PTO gear.
@@deepocean3603 Have you watched A Ritter bit will do? Jon has a easy to do way to get the length right😁👍
thanks for the video. I used this along with the manual to put my wc68 together today.you definitely saved me some headaches.
That’s awesome👍I am glad it helped. Thanks for leaving a comment. Enjoy the wood chipper😁👍🚜💨💡
Great and informational video. love the tape trick. this is definitely on my wish list. happy chipping
Thanks 😁👍 I think I want the stump grinder too but spending money faster than I can make it already😂 thanks for checking out the video🚜💨💡
So, they delivered my WC68 the other day and I'll be running it on a B2601 as well. Great info on the final assembly, especially the shaft sizing. It's gonna be a fun weekend.
Thanks 😁👍 other people have said cut off a 1 inch more than I did in the video on the PTO shaft and it will go on easier. But you will see if you need to or not😁Happy chipping 😁👍🚜💨🍳
Great video. I appreciate it, especially the detailed PTO shaft trimming section
Thanks 😁 after the video I did cut another inch to make it easier to put the PTO shaft on. Have a great Independence Day 😁👍🚜💨🍳
Thank you very very much.
Your welcome 😁👍thanks for checking out the video 🚜💨🍳
Nice job, my friend. Thanks for the shout-out! Let the wood chipping therapy begin. And yes, don't put that cup in the hopper! :)
Ha! Your welcome. I could hear your voice in my head about the “Hoppa” I got a lot to chip too. Thanks for watching and keep them live streams coming your really good at it. 😎🍻👍
Hi Mitch, great video as always. I'm seriously considering purchasing one of these and have now saved this so that I have a smooth assembly and installation. Thank you!
Thanks Dave!!!😁👍 I know you will love it we sure do. Have a great week 🚜💨🍳
Awesome step by step video. My chipper is being delivered next week and your video gives me the insight to hopefully put it together as well as you have. Thanks
Thanks for the comment it goes together pretty easy. In the video when I cut the PTO shaft I cut it the way the manual said and I ended up cutting another 1 inch extra off so it made it easier to put on. Another viewer told me he did that and it made it better so I did it too. Congratulations and happy chipping ☀️😁👍
BEST ASSEMBLY VIDEO EVER !
Was such a great help.
Excellent Job 👍
Thank you 😁👍 I enjoyed making it have a great weekend 🚜💨🍳
I’d love to have one of these. I first saw this on Ed’s channel. I’d probably have to go with the smaller wc46. Genius move with the blue tape and bolts by the way. Great video! 👍
Thanks that video took forever to edit. I was also thinking of the wc46 but then I saw Ed’s video. You and Ed got a good sense of humor on your videos🤣
Dude great video and very clear guidance during the install! Just got my WC68 for my L3901 and I'm excited to start the process! I appreciate folks like you taking the time and being brave to make these videos. GREAT JOB AND THANKS AGAIN!🤙
Thank you for the kind words😁👍 I did as good as I could at the time of the video. Looking 👀 back the one thing I would add is if the red handle keeps kicking into neutral then you will need to adjust the relief valve under the hopper. Have a great day!!!🚜💨🍳
@@MJADoingStuff
Hey mitch what type of hydraulic fluid did you use for the chipper?
@@Livn-4-Rapture are you asking about the brand?
@@MJADoingStuff yeah and the type? Lots of brands out there, just wondering if you had a preference.
Just finished putting mine together now just have to do the pto shaft, grease and fill fluid🤙
Your videos are so proffessional 👏
Thank you for your positive feedback keep Doing Stuff Pete 😎👍
Awesome video! Keep up the great content!
Thanks 😁 Have a fun and safe 4th of July!!! 😁👍🚜💨🍳
we ordered ours a couple of weeks ago and it is being delivered tommorrow. Thanks for taking the time to show how to assemble. Will save me time and frustration this weekend. Happy chipping!
Yep no problem 👍 your going to love it. When you get a chance check out Sawing with Sandy’s video on adjusting the relief valve for the red control handle if you have a problem with the infeed roller popping in to neutral a lot Happy Chipping! Sounds like a new holiday 😁👍
will do. thanks
Watched Sawing with Sandys video on adjusting the infeed roller. Looked to me like you were having same problem. Did you fix yours the same way?
@@mikedurkin8970 Not yet but the next time I use it I will. I am skipping the bleeding of the system and trying the adjustment part first.
Yesterday I got the chipper assembled and I ran it for the first time. Thanks again for tips. I remembered most of them and they saved me a lot of time and effort. After a test run I made a couple adjustments as the infeed rolller did kick into neutral on about every other limb and didnt want to grab anything over a couple inches. I did as you did and decreased the tension on the springs which solved the grabbing of the larger limbs. I did what was suggested in the manual and by you, and took off the plastic cap on the rear of the control lever, loosed the jam lock nut with a 7/8" wrench and rotated the set screw with a 6mm allen wrech, clockwise one turn. I also did what Sawing with Sandy suggested and tightened the set screw adjusment under the feed speed control valve. Like you, I didnt bleed the system. Not sure which of the two fixes was the trick, but after those two adjustments, It only kicked into neutral a few times out of about 100 limbs. Was so much fun, I didnt mind the rain.... One other thing. I trimmed the shaft as instructed. Still too long, so I will probaby take another inch off before next time I try to hook up PTO. Way too hard to get it on... Thanks again!
Excellent excellent video. Just what I needed as my chipper arrives this morning. Thanks for your great work!
Thanks 😁 congratulations on your new chipper your going to love it. Happy chipping 😁👍🚜💨🍳
@@MJADoingStuff thank you sir and for what it’s worth I think Woodland Mills should be linking to your video for how to put together their chipper. It’s essentially the Manual on video.
@@ianmclean5541 maybe one day. I appreciate your kind words😁👍
Nicely done
Kept me engaged thru the whole video !
Love the metal crate that’s a bonus and another video I’m sure 😂
Thanks Phil that was a long one took forever to edit. Yep that metal crate is going to be a winter project for sure. Thanks for checking out the video I appreciate it ☀️😁👍
Very good video helps me out thank you
Thanks 👍Glad I could help😁Your going to enjoy the WC68 have a great evening 😁👍🚜💨💡
Nice job, Mitch. You’re going to love it! Cheers!
Thanks Mike! It was a long video Thank you for checking it out 👍🍻
I made a category one ball hitch to pull my trailers easily to parts of my property and I am attempting to modify it to make a landscape rake. The spring times can be purchased fairly cheaply. These would be attached to a boom which be taken on and off the cat one ball hitch already fabricated. I Ike the way you use your plasma cutter as a manual cnc cutter by using patterns. Basically, young man, I like the way you think.
Thanks for your input and sharing your ideas on making a landscape rake. Great minds think alike. I am hoping to purchase a CNC plasma table one day but for now the patterns work pretty good. Have a great day.😁👍🚜💨🍳
A very nice video and some great assembly tips, i liked the tape on the bolts.
Thanks for checking out the video it was a long one lots of editing. Hope to see you on the next one 👍😁
@@MJADoingStuff I have one of those 800 lb boxes sitting in my yard so today is the day i open it up if the weather cooperates.
@@raincoast9010 That is awesome I love the excitement I get when I start a project. I think 🤔 the chipper is our favorite implement. Enjoy 😁👍
Your video's are so fascinating, its like when your a kid watching your dad do something you have no clue about lol
Thanks your videos make me feel I need to get out and be more active I like learning new stuff 🍻👍 have a good weekend!
Looks nice. Enjoy and work safely.
Thanks I will. Spring is almost here got a lot to chip up at the property 😎👍🍻 Thank you for your comment.
Great video M, very detailed 👍🏻, you did a great job !
Thank you. It was a long one. Lots of editing. I hope it helps someone out there one day 😎👍🍻
@@MJADoingStuff I’m sure it will 👍🏻
I ordered a WC88 yesterday. I never buy Chinese made machines, but there are so many good comments that i made an exception.
I have been waiting to get good weather to put it to work. Also my B2601 is still at the dealer for repair on the loader issue. I get what you mean on the Chinese made stuff but seems like Woodland Mills has the customer support dialed in. We will see🤞😁👍 congrats on your purchase. Thanks for watching 🍻
@@MJADoingStuff Thanks! I will follow your video's and will give my opinion on the WC88 here too. I will chip the hell out if it when the snow has gone ;-)
@@rapalaron6348 Sweet👍😁
@@MJADoingStuff Delivery problem with Woodland Mills Europe with my WC88 order.
I ordered the chipper on Monday the 22 march. When i got a copy from the order and the invoice it said that the chipper was out of stock and expected back in stock the 24. of march. I thought, that is only a few days so i payed about 4000 Euro,s. I would get a track and trace number when shipped to me. Nothing happened. Today i send a mail to Woodland to ask if they got the shipment with the new machines. Answer was yes, we got yesterday chippers but they where already sold and my chipper will be send to me when they get a new shipment. When i put the WC88 in the chart it did not say that is was out of stock. It was only told to me when i got the invoice. Now i have to wait at least 3 more weeks to get my chipper home. This is no way to do business, and i'm thinking to ask for refund.
@@rapalaron6348 Sorry to hear that. I most have ordered it just before it got busy. Attachments and parts are getting hard to get my Kubota dealer still waiting on parts for my tractor Maybe see if another company can get one sooner then get a refund.
I just put mine together. Seems to work well but when I tried putting a 4" thick branch in the infeed roller wouldn't climb up. Going to try to loosen the springs like you did. Thanks for the video.
Congratulations happy chipping!!!😁👍🚜💨💡
Looking good!!
Thanks hope that helps with your thoughts about the WC68 thanks for checking out the video ☀️😁👍
I realized you watched the step-by-step assembly video I meant for you to watch WC68 first time on the property in that video we chipped a lot of wood with the RPMs on pic and pic.
Those roller springs -- if you don't have a lot of tension then the roller won't bite the small stuff. Yes, more tension means tougher for the roller to swallow big stuff -- it is a balancing act between the two.
You are correct!!! 😁 I must have got lucky haven’t changed the setting sense the video and the small stuff goes through without a problem but if I put anything over 4” inches it will have trouble climbing on top to pull it in. Luckily I burn anything over 4” inch 😂 thanks for sharing and have a great weekend 😁👍🚜💨🍳
Greetings from NE Florida. Found you in the comments on My Cluttered Garage channel and popped over to check out the channel! Subscribed to follow along with you. - Rick
Sweet! Thank you for making a comment and subscribing I am excited almost to 100 subs it was my first goal. You made my day 👍🍻
@@MJADoingStuff outstanding - just stick with and the goals will be met one at a time. - Rick
Where were your helpers ? When I saw the shipping stand I knew you would be building with it !
I got some ideas 💡 for sure 👍😁
Very informative. I watched the whole thing but the background music was annoying and detracted a lot from the video. It would have been fine over a sped up work sequence time lapse but not over something instructional like this.
Good to know I am still learning I will keep that in mind when I edit. Thanks for the feedback😁👍 have a good weekend.
I liked the background music 👍😊
@@deepocean3603 😂👍
What brand of oil was on box?
It was Mystik ISO 32 from Fleet Farm. Thanks for watching 😁👍🚜💨☀️
Hello, good morning, could you tell me the exact reference of the chipper motor? Thank you
Not sure what you mean by chipper motor?😁
@@MJADoingStuff I am making a machine to drag wood and I would like to know what power that motor is. Thank you
@@tofd21flauta22 Sorry I don’t know what size the hydraulic in feed motor on the chipper is but the tractor has 19.5 PTO hp. 😁🚜💨🍳
If I ever get to build one of these for myself out of the box, I believe I will surely llll dab a b dollop of good old roofing tar on the nuts and bolts especially the ones that will surely rattle loose right into the speeding chipper blades. Not blue Lock-tite Ernie lock'tite like every mechanic will tell you to use but tar . If tar belongs anywhere it belongs on a chipper in the woods because if you dont come home blackened with tar you aint been working ,t you yu you just been dilly dallying. Seriously though the hopper should be iether welded togeather or at least glue the bolts togeather. Those nylon lock nuts are not lock nuts . A tight nut and bolt with sheet metal between is not locked. A lock nut is two nuts next to each other with no washers and tightened against each other with two box end wrenches. That method of lock nut will stay locked forever even when the metal pieces have fatigued and the bolt is rattling in its hole.
Good to know thanks I will keep a eye on the bolts and nuts. Thank you for checking out the video 😁👍