Thank you for this information. In my case this light lit up after I lubed the chain and ran it in 1st gear on center stand. My bike wasn5 washed or drenched in rain at all. "In my case" This may be a bug as the front wheel is not running but the rear one is during chain lubrication, should go away after few stop/starts. Just wanted to share this scenario too.
I have experienced this problem twice after washing my bike and get rid off by turn on/off the ignition fastly more than 5 times continuously. But this video helps to understand the root cause of the issue along with proper resolution. Thanks a lot and keep rocking..
Thank you so much. 2-3 days back only I bought this new bike and faced same problem after washing. I was really worried as the indicator was continuously on. This video helped me to solve the problem. thanks a lot again
Nice video Sir. With BS6 there are plethora of sensors 😁. A tension always looms over whenever I take my BS6 RTR 200 for a wash..Was never ever scared taking my BS3 Bullet Standard 500, that stead was a rugged machine 😉
Thanks bro i was facing the same isuue after washing the bike, after cleaning the sensor portion as you explained the engine check lamp stopped blinking. It worked thanks a lot.🙂
I also have this problem when ever i do washing of CB350 RS .. The Engine Check light turn on.. I have read some reviews and do it by my self .. Just after washing make sure blow AIR and do at least 5 to 10 km ride. It will solve the check light issue . 👍
I had a similar problem, after lubing my chain y`day. Visited the service center today and heard that if you run it on gear with center stand you will come across the ignition light ON. He did a reset and gave the byk back. His suggestion is not to start and run the byk on center stand. Not sure whether it makes sense or not,.
Sir, I too am a highness owner and have faced this issue after washing once but instead of finding water there I was able to find a small amount between the ecu socket pins(the black socket where the wiring kit is connected to ecu socket)and wiping them off using cotton waste solved the issue. Sometimes after riding for a quite while and restating the engine after stopping at the traffic signal,I found the idle rpm to go so low that the engine would shut down itself if not revved.Have you ever faced this issue?
I too have this engine light on, the only thing I did was clean chain and lube it with Motul C1 & C2. Not sure what sensor it may be affecting ? Wheel spin sensor near Disk break ?
Brother please check if your bike also has disproportionate gap between forks and tank on each side(when we twist the handle to the extreme), because of this i am feeling like my handle bar is not aligned properly, all the cables are intact and not trying to pull the handle bar either side. Help
Most of the times, washing isnt required. I dont see the service center guys following the process stated in the manual. Mostly the lower portion of the bike should be sprayed and immediately blow dried. I dont want the sevice guys to wash my bike. They can change oul and do other adjustments. Good video.
Even my bike got this lamp on, after heavy rain so tried this but still getting on. But didn't check that another sensor you mentioned in very last part of video can you tell me how to open and where it is located
When number of exposed electrical / electronic connections increased, chances of water short circuiting increased. In Old Jawa, Yezdi, Rajdoot, Lambretta, Bajaj 150 etc usually only spark plug adapter got short circuited by rain water or servicing water like this. Tecnology advanced and likewise problems increased.
Thank you dear . Your video was very useful to me. I was about to visit the service centre as i had the same problem. Did the air pressure both in plug and the sensor I could see the engine mal function light off immediately. Thank you
Hi sir ! Very informative, i have a problem with cb350 where after few secs of self engine is getting stopped, no malfunction light and no stand indicator as well Could please plz let me know what could be the reason
My check light is on after I lubed the chain....I put bike on main stand and engage first gear and then by using wheel rotation I lubed my chain ..I guess the speedo was at 0 and wheel was rotating so that causes the error...but my question is ..is there anything i should do
Great info. I faced the same problem after I washed the bike at home. Luckily I just switched off the bike and switched it on again and the light went off. Please share info on the air pump you used. Also in one of your videos you mentioned that you do a dry wash for your bike. Please make a video on that as well. It would be really helpful
Hi Vinay, Can you please make a video about the problems you observed after first service. I did found some issues like vibration near foot rest and rear break sound even after fixing the multiple times.
RE Meteor is also a very good bike, infact it's a most reliable RE ever...I just ride it once and can tell that RE has come a long way in terms of R&D to make reliable machines.
This is correct. It happened with me too during first service as you said there could be water... In my case the ABS indicator was also blinking.. I took the bike back to service center... they couldn't find anything and it never happened after that.. possibly i never washed or got the bike washed after that...
I think its fine as long as we know how to check and fix the issues.. Cb350 is an advanced motorcycle with electronics in it as compared to BS4 motorcycles available in India till last year... Mostly if we know how to fix it its ok to live with
@@rohitsaha29 True. There is one more thing that is bugging me. After first service, average indicator is fluctuating like crazy. I talked to showroom people..they said it's normal...but before my bike's first service it wasn't fluctuating randomly. Is there any issue here?
@@nawkarak well there is a trip average which tells you the average of the trip A for example until you reset trip A. There is a real time average indicator which is 0 when the engine is off but ignition is on. When you start riding it changes as per fuel consumption.. you will see when you are slowing down with closed throttle it even shows 99.9 and ECO green indicator glows... In this case sevice center guys are correct amd its normal
Same happened with me yesterday.. After washing the bike at a service station, first the service indicator started blinking, which is continuing till now. Today, the ABS indicator started blinking and the battery voltage dropped to 9.5, even while riding the bike... What could be the reason ? Is it the washing by pressure pump ?
Hi Sir, My bike is only 3 months old however suddenly I got the bike showing engine sign today. Neither I got my bike washed nor it was wet in the rain. Could you tell me if as per you this could be major issue. just want to know your thought.
Never had any such issues, might want to get the spark plug swapped and check, hope this didn't start after water washing, if not most likely plug is the culprit... If not it could be the ignition coil.
@@motovin77 No water washing done yet, odometer is only at 100 km, I think so too plug is the culprit, wanted to show the service center guys but due to lockdown everything is closed
I just goth this light 2 days back, I am really fed up of this bs6 bike and its sensor issues, Thinking I should have bought second hand Lord Splendor. Really waste of 3 lac money on this Honda 350 . Anyway I will try this and update. Thank you.
Wonderful video🙏 Just happened to stumble upon your channel a couple of months back, the only time I have praised UA-cam's algorithm for suggesting videos. And quick question, what do you think of the CB 350 RS?? Many people seem to be confused with not just the RS badge but also what the bike has to offer over the H'ness.
Sir i have ridden my cb 350 470km only... I got delivery by feb 4....can i service it today(22.02.2021).Cause i recognised a problem while simply opening the throttle while in neutral.
Hi sir, thanks for the information. Just wanted to confirm that in my highness, the engine light is on when engine kill switch is in on position (red button is pressed upwards). When I turn off the engine kill switch (red button is pressed downwards), the light goes away, is it supposed to be this way only?
Yesterday i too did the same thing of lubing chain on 1st gear and now the engine malfunction light is on. Wat to do ???? ( Thanku @Angad Katdare, i switched off the TC and moved the bike little, then did a on/off and voila Malfunction light is gone)
@@Siva.P.S The same thing happened to me today . I lubed the chain while the bike was on 1st gear . Turning off the traction control and moving the bike a bit and turned off and back on .. The malfunction light went off . Thank you
Hi Vinay, this is useful.Thank you. Also, any tips on how to turn off the service due indicator which shows up in the Odometer even after the bike has been recently serviced?
I have a question, please - I understand it isn't related to the video- Would you buy the CB350RS or CB350 Highness? Your answer will help me make an informed decision. Thank you, Vinay.
Both are essentially very same bikes with little different ergonomics, RS will be more liked by the younger crowd, if you are someone who prefers trendy design it would be RS else the classy timeless Highness.
@@StallionRides major difference apart from the esthetic point would be the riding ergonomics, RS is bit more committed/aggressive as tye rider foot pegs are rear set and handle bar more closer... Some what like Interceptor. If you prefer relaxed position it will anyday be Highness
@@motovin77 I ride like a responsible maniac, I love taking those gaps and corners- hope that helps- 29 years,- lean mean you may say. I like aggressive, simply because when you ride a motorcycle- you are riding a motorcycle- that's commitment- and for that reason, a riding stance does make a difference. I somehow yet like the Highness- I don't know- just can't get over the looks- of course, the refinement I saw them both side by side- I find myself attracted to the old world charm somehow..
@@motovin77 I saw the other video you posted too- Where I am, the dealership isn't making a test ride available for RS- they claim that both bikes are the same - I wonder they even know what tires, lower set handlebars, rear-set pegs do to the overall riding experience. Sometimes I feel, Honda is trying too hard to expand the dealerships- I wasn't quite happy after visiting one of the dealerships- Also, didn't experience that premium feel people keep describing- A better-trained staff would do wonders for them- maybe I'm just passionate about motorcycles.
Use Hand pump pressure spray bottle 2Ltrs. 1 Ltr water/ prime to build pressure. Use liquid hand wash. Use flat brush with long handle + jiff floor cleaning cream mixed in quarter bucket of water to clean hard mud and grease.
I think i found out what the Issue is. I started the vehicle while on centre stand and shifted to 1st gear. Did this cause was getting a squeaky noise somewhere close to the wheels. The engine check indicator i.e PGM-FI is on cause our bikes have traction control and it calculates the ratio of both the wheel movement. Since the front wheel was not moving for a while the indicator is on now.
@@sumithsuresh4099 did you wash your vehicle? If so what Vinay suggested is the best way. If you have started the vehicle while on centre stand i.e engaged the gear then go for spin automatically it would go
sir could you please instruct us where to get fog lamps fitted from in bangalore without voiding the warranty?? also sir, chain seems to be making noise while giving throttle after 30kmph, noise seems to be coming from the front sprocket area more, service centre guys are saying there is no issue because they are cheats, do you have any suggestions for both these? please respond. I have the new 2023 Hness. @motovin77
Sir, If you remember, I had referred to my bike not getting started, and I had to give a jump start to the battery, to start the bike... It happened again. This time, the bike was parked on side stand for some 10 minutes only, but when I tried to start, it didn't start. Only after some tries it started. Can it be because of parking on side stand, the petrol gets in contact with the plug or something and bike doesn't start ?
It really cannot be the side stand, unless there is an issue with the side stand cut off switch... Else some other loose or or the battery itself... Flow of petrol is through fuel injection and that cannot go wrong.
@@motovin77 Yes sir. It seems there is an issue with the battery. The thing is that, the service centre is almost 20-30 kms from my home, and I had not taken the RSA. So, the service centre guy wants me to take the bike there and leave it with them for a day or two, so that they can analyse and find out the fault. Then, if they find the battery faulty, they will raise a request in the company for a replacement battery, which might take 8-10 working days.. I'm highly pissed off and feel so humiliated when my colleagues and the onlookers tell me "Arrey nayi bike aur dhakka maarna pad raha hain !!!" & "Itni mahangi bike aur 3 months mein battery issue start !!"..
@@motovin77 After posting a stern message at Bigwingmumbai's Instagram page, they agreed to pick up the bike from my location and get the battery checked. If the battery is really faulty, they will replace it, but will take 7-10 days. Another thing, the service centre guy asked Rs. 945/- rupees as pick up charges., Again, one filthy message to the IG page and Yo! , the entire cost got waived off...
@@mohzampatni2 sadly it's all indian way of Customer service, if it was west there would be a mobile service van at location and replace the spare then and there or provide a backup bike till such time. Hopefully your reply de is back soon with all issues sorted.
Same here. I'm getting same mileage after first service. Many people said it would be close to 38-40 after first service. For me average trip mileage is showing around 28. Not sure if those trip AVg numbers are accurate.
Thank you for this information. In my case this light lit up after I lubed the chain and ran it in 1st gear on center stand. My bike wasn5 washed or drenched in rain at all. "In my case" This may be a bug as the front wheel is not running but the rear one is during chain lubrication, should go away after few stop/starts. Just wanted to share this scenario too.
I came her after doing exactly the same thing and. Found your comment
Bro just happened with me today what to do.. chain clean kiya aur lub kiya. Engine light aaraha he
@@terabaap378 it will be alright after a day
@@sendilraghvan7794 okk thanks bro.m will check tomorrow.
Same issue
Great....Always provides non nonsense guidance....Thanks for sharing all videos right from first ride to till date videos.....🙏🏻
love to watch your videos and its pure informative ! for our highness owners
I have experienced this problem twice after washing my bike and get rid off by turn on/off the ignition fastly more than 5 times continuously. But this video helps to understand the root cause of the issue along with proper resolution. Thanks a lot and keep rocking..
Great. You are truly sharing informative videos for all hness owners. Keep on putting such videos. Subscribed 😊
Thanks for the quick tip
Saved me kms of ride to bigwing showroom and even some unwanted bigwing charges 😅
Thank you so much. 2-3 days back only I bought this new bike and faced same problem after washing. I was really worried as the indicator was continuously on. This video helped me to solve the problem. thanks a lot again
Thanks, sometimes the engine light will be on after washing the bike. This video gave me a good clarification
Nice video Sir. With BS6 there are plethora of sensors 😁. A tension always looms over whenever I take my BS6 RTR 200 for a wash..Was never ever scared taking my BS3 Bullet Standard 500, that stead was a rugged machine 😉
That's true sir 😀
Nice debug & findings and very helpful information too 💐👍
Thanks bro i was facing the same isuue after washing the bike, after cleaning the sensor portion as you explained the engine check lamp stopped blinking. It worked thanks a lot.🙂
Very very informative vdo.. Thanks a ton for sharing your valuable experience.. Waiting for other vdos on highness..🙏🙏👍👍👌👌👏👏
Very useful solved my problem after your video👍
Very useful video, thanks a lot 👍😊
Thanks Sir, it is very useful tip from you Sir
No nonsense content only ..👍👍👍👍
I also have this problem when ever i do washing of CB350 RS ..
The Engine Check light turn on..
I have read some reviews and do it by my self .. Just after washing make sure blow AIR and do at least 5 to 10 km ride.
It will solve the check light issue . 👍
Very useful...thanks🙏🙏
Very informative 👏
Very useful...thanks 🙏
Thanks a lot for the help sirji....it helped me....
I had a similar problem, after lubing my chain y`day. Visited the service center today and heard that if you run it on gear with center stand you will come across the ignition light ON. He did a reset and gave the byk back. His suggestion is not to start and run the byk on center stand. Not sure whether it makes sense or not,.
Bro, you the man....this worked for me
Sir,
I too am a highness owner and have faced this issue after washing once but instead of finding water there I was able to find a small amount between the ecu socket pins(the black socket where the wiring kit is connected to ecu socket)and wiping them off using cotton waste solved the issue.
Sometimes after riding for a quite while and restating the engine after stopping at the traffic signal,I found the idle rpm to go so low that the engine would shut down itself if not revved.Have you ever faced this issue?
Great. Keep rocking
I too have this engine light on, the only thing I did was clean chain and lube it with Motul C1 & C2. Not sure what sensor it may be affecting ? Wheel spin sensor near Disk break ?
What are the things I need to purchase for fitting bar end weights.....
Brother please check if your bike also has disproportionate gap between forks and tank on each side(when we twist the handle to the extreme), because of this i am feeling like my handle bar is not aligned properly, all the cables are intact and not trying to pull the handle bar either side. Help
Man you are a life saver
Thanks🙏🙏🙏
Most of the times, washing isnt required. I dont see the service center guys following the process stated in the manual. Mostly the lower portion of the bike should be sprayed and immediately blow dried. I dont want the sevice guys to wash my bike. They can change oul and do other adjustments. Good video.
Even my bike got this lamp on, after heavy rain so tried this but still getting on. But didn't check that another sensor you mentioned in very last part of video can you tell me how to open and where it is located
If we dont blow out the water will it go off after few days? Do i have to remove and clean
When number of exposed electrical / electronic connections increased, chances of water short circuiting increased. In Old Jawa, Yezdi, Rajdoot, Lambretta, Bajaj 150 etc usually only spark plug adapter got short circuited by rain water or servicing water like this. Tecnology advanced and likewise problems increased.
Thank you dear . Your video was very useful to me. I was about to visit the service centre as i had the same problem. Did the air pressure both in plug and the sensor I could see the engine mal function light off immediately. Thank you
Glad you found this useful and helpful to solve the problem.
Hi sir !
Very informative, i have a problem with cb350 where after few secs of self engine is getting stopped, no malfunction light and no stand indicator as well
Could please plz let me know what could be the reason
Thank you for sharing this😊🙏
My check light is on after I lubed the chain....I put bike on main stand and engage first gear and then by using wheel rotation I lubed my chain
..I guess the speedo was at 0 and wheel was rotating so that causes the error...but my question is ..is there anything i should do
New CB 350 RS your thoughts
Great info. I faced the same problem after I washed the bike at home. Luckily I just switched off the bike and switched it on again and the light went off.
Please share info on the air pump you used. Also in one of your videos you mentioned that you do a dry wash for your bike. Please make a video on that as well. It would be really helpful
I just used a cycle air pump.
@@motovin77 😃 I thought you had some kind of small electric pump
Just use vaccum cleaner blower side
Hi Vinay, Can you please make a video about the problems you observed after first service. I did found some issues like vibration near foot rest and rear break sound even after fixing the multiple times.
Even i faced same issue brother. I loosen my chain little bit and after 200 km that issue got resolved automatically
same...thing
If possible please share your experiences about RE Meteor 350...
RE Meteor is also a very good bike, infact it's a most reliable RE ever...I just ride it once and can tell that RE has come a long way in terms of R&D to make reliable machines.
Thanks 🙏
Please make a Video on Range & Real time Mileage information because my Real time mileage is very wrong showing 86,90, etx
Did you find out malfunction code? Ex) P0300 with tester
Thank u 🙏
This is correct. It happened with me too during first service as you said there could be water... In my case the ABS indicator was also blinking.. I took the bike back to service center... they couldn't find anything and it never happened after that.. possibly i never washed or got the bike washed after that...
This blinking of ABS indicater is happening in my case. I got my first service done yesterday itself.
I think its fine as long as we know how to check and fix the issues..
Cb350 is an advanced motorcycle with electronics in it as compared to BS4 motorcycles available in India till last year...
Mostly if we know how to fix it its ok to live with
@@rohitsaha29 True. There is one more thing that is bugging me. After first service, average indicator is fluctuating like crazy. I talked to showroom people..they said it's normal...but before my bike's first service it wasn't fluctuating randomly. Is there any issue here?
@@nawkarak well there is a trip average which tells you the average of the trip A for example until you reset trip A.
There is a real time average indicator which is 0 when the engine is off but ignition is on. When you start riding it changes as per fuel consumption.. you will see when you are slowing down with closed throttle it even shows 99.9 and ECO green indicator glows...
In this case sevice center guys are correct amd its normal
Same happened with me yesterday.. After washing the bike at a service station, first the service indicator started blinking, which is continuing till now. Today, the ABS indicator started blinking and the battery voltage dropped to 9.5, even while riding the bike... What could be the reason ? Is it the washing by pressure pump ?
How do you clean the fins of the engine? It's really tough to clean the dust inside it?
No it’s easy I do clean on my own !
Hi, can we replace the Gear lever like cb350 RS?
Itl look better I guess
We should be able to... Seat, engine plate
Hi Vinay, one quick question can you suggest some place in Bangalore where I can buy riding gear (helmet and gloves)
Thanks 😊
There are many places such as Let's Gear Up, BikingSpirit, Orion Motors Riding Store, Gear N Ride etc...
@@motovin77 will visit today
Sir, CB 350 RS review maadi please...
Hi Sir, My bike is only 3 months old however suddenly I got the bike showing engine sign today. Neither I got my bike washed nor it was wet in the rain. Could you tell me if as per you this could be major issue. just want to know your thought.
Same do you get solution bro pls reply
Did you face any issue with self start? I am facing for a number of days now, have to remove spark plug cap , blow it and then it starts to work..
Never had any such issues, might want to get the spark plug swapped and check, hope this didn't start after water washing, if not most likely plug is the culprit... If not it could be the ignition coil.
@@motovin77 No water washing done yet, odometer is only at 100 km, I think so too plug is the culprit, wanted to show the service center guys but due to lockdown everything is closed
I just goth this light 2 days back, I am really fed up of this bs6 bike and its sensor issues, Thinking I should have bought second hand Lord Splendor. Really waste of 3 lac money on this Honda 350 . Anyway I will try this and update. Thank you.
Hi sir , Even I am facing the same problem after washing but even after trying whatever you said problem is still there . Any other idea ?
You have got foglights. Does it affect the warrenty,?
Not really if installed with out splicing the original wiring...
Wonderful video🙏 Just happened to stumble upon your channel a couple of months back, the only time I have praised UA-cam's algorithm for suggesting videos.
And quick question, what do you think of the CB 350 RS?? Many people seem to be confused with not just the RS badge but also what the bike has to offer over the H'ness.
Sir i have ridden my cb 350 470km only... I got delivery by feb 4....can i service it today(22.02.2021).Cause i recognised a problem while simply opening the throttle while in neutral.
Yes you can book appointment and go for first service 👍
Hi sir, thanks for the information. Just wanted to confirm that in my highness, the engine light is on when engine kill switch is in on position (red button is pressed upwards). When I turn off the engine kill switch (red button is pressed downwards), the light goes away, is it supposed to be this way only?
Correct sir. That's perfect 👍
@@motovin77 thank you sir🙏
Thanks for the video. I found that indicator to turn on when i chain lube my bike. It stays for a day and then goes off.
That's very strange as there is no correlation between lubing chain and engine malfunction light.
@@motovin77 Honda service center guys told me this was because I put the bike on first gear (to spray lube) without turning off the torque control.
@@motovin77 strange , but that happened to my bike too .. the exact same issue .
Yesterday i too did the same thing of lubing chain on 1st gear and now the engine malfunction light is on. Wat to do ???? ( Thanku @Angad Katdare, i switched off the TC and moved the bike little, then did a on/off and voila Malfunction light is gone)
@@Siva.P.S The same thing happened to me today . I lubed the chain while the bike was on 1st gear . Turning off the traction control and moving the bike a bit and turned off and back on .. The malfunction light went off . Thank you
Have you done any coating on your bike?
No coating on the bike.
My trac control, abs and engine failure light is on suddenly and not stopping
money saver. i just had to blow the spark plug cover 😍
I haven't washed by bike yet .it's been only five days since I took delivery. The PGM - FI light Is on after ignition .what should I do ???
Is the light on even after starting the engine? If so follow this procedure
Thank you man.. I got my Rs washed and the engine sensor indicator is on.. Let's see tomorrow if it gets dry out.
Did it go off on it's own?
@@hardikpandya7421 I removed it and plugged it back. Then sometime later it went off. Other times also it went off on its own
@@vishnureddys4801 ok bro. Thanks. 👍
Hi Vinay, this is useful.Thank you. Also, any tips on how to turn off the service due indicator which shows up in the Odometer even after the bike has been recently serviced?
ua-cam.com/video/Xw5Bqgu_lME/v-deo.html
@@motovin77 thanks, Vinay. This helped.
Which locality do you live sir? Very nice environment in blr
Sarjapur.
Sir, is it normal that engine heats up after a short city ride before first service?
Absolutely normal.. just enjoy the ride😀
@@motovin77 thank you 👍🙏
In your chain maintenance video, Is it kerosene you use?
Why is it blue in colour
What I got from local shop is almost transparent
Yes it was kerosene, here in Bangalore ration shops the kerosene is added with blue colour to prevent black marketting. But still it continues 😀
@@motovin77 Ohhh Okay didn't know this...
Bro are you facing any heat issue near engine after riding for 5 kms
Nothing as such...
When you get oil change ask Bigwing to use honda Throttle fully synthetic oil, it will help
How to remove the headlight assembly and holder?
Detailed instructions are there in owner manual, if not there are videos on youtube
Hello....the engine malfunction light keeps on after I did chain lube.Any solution for that?
same for me. How did you fix this?
Same here also
I have a question, please - I understand it isn't related to the video- Would you buy the CB350RS or CB350 Highness? Your answer will help me make an informed decision. Thank you, Vinay.
Both are essentially very same bikes with little different ergonomics, RS will be more liked by the younger crowd, if you are someone who prefers trendy design it would be RS else the classy timeless Highness.
@@motovin77 Thank you, Vinay.
@@StallionRides major difference apart from the esthetic point would be the riding ergonomics, RS is bit more committed/aggressive as tye rider foot pegs are rear set and handle bar more closer... Some what like Interceptor.
If you prefer relaxed position it will anyday be Highness
@@motovin77 I ride like a responsible maniac, I love taking those gaps and corners- hope that helps- 29 years,- lean mean you may say. I like aggressive, simply because when you ride a motorcycle- you are riding a motorcycle- that's commitment- and for that reason, a riding stance does make a difference. I somehow yet like the Highness- I don't know- just can't get over the looks- of course, the refinement I saw them both side by side- I find myself attracted to the old world charm somehow..
@@motovin77 I saw the other video you posted too- Where I am, the dealership isn't making a test ride available for RS- they claim that both bikes are the same - I wonder they even know what tires, lower set handlebars, rear-set pegs do to the overall riding experience. Sometimes I feel, Honda is trying too hard to expand the dealerships- I wasn't quite happy after visiting one of the dealerships- Also, didn't experience that premium feel people keep describing- A better-trained staff would do wonders for them- maybe I'm just passionate about motorcycles.
Was useful, could repair the bike
Sir, do you have engine heating issues
No sir, no heating issues
sir are those scratches in your tank?
Not scratches, threads from the cloth I last used to wet wipe the tank😀
Use the following:
After cleaning the inside of the male contacts and use:
Silicone Conductive Gel.
By: Sun Electric, Bengaluru
Use Hand pump pressure spray bottle 2Ltrs.
1 Ltr water/ prime to build pressure.
Use liquid hand wash.
Use flat brush with long handle + jiff floor cleaning cream mixed in quarter bucket of water to clean hard mud and grease.
are there any paint peeling issues on engine?
No, i didn't have any issues
@@motovin77 but I did notice some peeled off paint, during the video.
After washing... Traction control indecator blinking....what is the root cause...pls reply sir where i have to check water or dust????
Water must have seeped into the electricals, after washing blow with pressurised air or keep it in sun for an hour, it should go away.
No need for power wash during the service.
One of my friend experienced loss of paint in isolated spots near the engine after repeated washing .
👏
Traction control test video .
I am facing the same problem, still not resolved also I have not washed my bike till now. Any thoughts or suggestions
All the couplers going into the other sensors need to be checked, most likely it's a sensor issue.
@@motovin77 thank you for the quick response, any idea how we can check the individual couplers? I am not really good at this 😁 but can do if guided
I think i found out what the Issue is. I started the vehicle while on centre stand and shifted to 1st gear. Did this cause was getting a squeaky noise somewhere close to the wheels. The engine check indicator i.e PGM-FI is on cause our bikes have traction control and it calculates the ratio of both the wheel movement. Since the front wheel was not moving for a while the indicator is on now.
@@kamekaze213 bro I got this issue today.. how to solve this issue? How did you solve this issue
@@sumithsuresh4099 did you wash your vehicle? If so what Vinay suggested is the best way. If you have started the vehicle while on centre stand i.e engaged the gear then go for spin automatically it would go
sir could you please instruct us where to get fog lamps fitted from in bangalore without voiding the warranty?? also sir, chain seems to be making noise while giving throttle after 30kmph, noise seems to be coming from the front sprocket area more, service centre guys are saying there is no issue because they are cheats, do you have any suggestions for both these? please respond. I have the new 2023 Hness. @motovin77
Sir, If you remember, I had referred to my bike not getting started, and I had to give a jump start to the battery, to start the bike... It happened again. This time, the bike was parked on side stand for some 10 minutes only, but when I tried to start, it didn't start. Only after some tries it started. Can it be because of parking on side stand, the petrol gets in contact with the plug or something and bike doesn't start ?
It really cannot be the side stand, unless there is an issue with the side stand cut off switch... Else some other loose or or the battery itself... Flow of petrol is through fuel injection and that cannot go wrong.
@@motovin77 Yes sir. It seems there is an issue with the battery. The thing is that, the service centre is almost 20-30 kms from my home, and I had not taken the RSA. So, the service centre guy wants me to take the bike there and leave it with them for a day or two, so that they can analyse and find out the fault. Then, if they find the battery faulty, they will raise a request in the company for a replacement battery, which might take 8-10 working days.. I'm highly pissed off and feel so humiliated when my colleagues and the onlookers tell me "Arrey nayi bike aur dhakka maarna pad raha hain !!!" & "Itni mahangi bike aur 3 months mein battery issue start !!"..
@@mohzampatni2 I truly understand how it feels like 😔
@@motovin77 After posting a stern message at Bigwingmumbai's Instagram page, they agreed to pick up the bike from my location and get the battery checked. If the battery is really faulty, they will replace it, but will take 7-10 days. Another thing, the service centre guy asked Rs. 945/- rupees as pick up charges., Again, one filthy message to the IG page and Yo! , the entire cost got waived off...
@@mohzampatni2 sadly it's all indian way of Customer service, if it was west there would be a mobile service van at location and replace the spare then and there or provide a backup bike till such time. Hopefully your reply de is back soon with all issues sorted.
What is the mileage of your bike bro?
Bro I've ridden my bike 470 km..the mileage I'm currently getting is 32.9😹.
@@thejaskarayil coz I was planning to buy as well.company claims 42 actually.which is not right I guess
@@thejaskarayil any ways thank you for reply.
My combined average is 36kmpl till date done 5000km
I hve also that problem.in my new bike jest delivered 😭😭
light drizzle and engine light turned on, and is still on.
Should not unless you have got the bike washed at service center, might want to have the sensor couplers checked once
It's not a inlet senser it's oil temperature senser
BTW with increasing fuel prices hness does a great job with range and average calculators 😂
Again.. Electronics 👍👍
😂😂😂
Yes but bike has been consistently delivering 37kmpl in mixed conditions. Quite happy with it.
@@motovin77 thats great.. i m getting 28 to 30 only.. inthis case i doubt the fuel quality
@@rohitsaha29 try shell fuel once to confirm
Same here.
I'm getting same mileage after first service.
Many people said it would be close to 38-40 after first service.
For me average trip mileage is showing around 28.
Not sure if those trip AVg numbers are accurate.
The bike ride is so nice... I dont care about mileage😂
Any one wants to kne how to clean engine fins do ask me guys
Content starts @2:49.
Thanks 🙏