- About drawing to build this machine, component list, electric list, wiring, progam for plc + hmi, contact me via email: tamnm7171@gmail.com or whatsapp: +84915767171
Can the temperature be adjusted via the HMI panel? If this is possible, then I think this is achieved by installing a relay between the heaters and the HMI. Temperature sensors are also connected to the HMI. In this case, thermostats will not be needed.
Hey sir great project, I wanna build It my self too, please give me the quote and if possible then can you sell me a full diy kit with the guide to make this my self. I am highly interested in This project. Please contact me
- About drawing to build this machine, component list, electric list, wiring, progam for plc + hmi, contact me via email: tamnm7171@gmail.com or whatsapp: +84915767171
Quanto custa o projeto e software?
Good job, it's so chill to watch your clip ❤i can watch it all day 😊
Thanks friend!
wonderfull machine!
thanks friend!
Hello! I was waiting for the third series, it turned out great, I see I replaced the stepper motor with an extruder drive.
Yes, I replace it
I'm also collecting, I'm thinking of installing nema 34 (12 Nm)
I’m using servo 750w instead of nema 34
Amazing build! Thank you!
Thanks, nice to meet you
Merhaba
Bu enjeksiyon makinesi ile 15 cm çapında max 4 cm yüksekliğinde plastik parçalar basılabilir mi ? 🇹🇷
150x4cm can’t
@@handmadenguyen 150 mm X 40 mm
Sorry, 150x40mm , contact me : +84915767171
Can the temperature be adjusted via the HMI panel? If this is possible, then I think this is achieved by installing a relay between the heaters and the HMI. Temperature sensors are also connected to the HMI. In this case, thermostats will not be needed.
Yes, I think this is best solution for this machine
The desired mold does this how to purchase...
Contact me via email: tamnm7171@gmail.com or whatsapp: +84915767171
It's a nice build! Why are you using a servo motor (in the injection unit) instead of a stepper motor?
I need to increase speed of screw
@@handmadenguyen is the torque enough?
Enough
@@handmadenguyen thank you
Se podra inyectar piezas de 8 cavidades ? cavidades ?
Can be 8cav
Thanks
Thank you! I have recieved your email
Type of temperature sensor
Omron E5CC
@@handmadenguyen model of thermocouple
Type K
Thermocouple Type-K (0:1000 °C)
Yes
Prices
Please contact me via email: nguyenminhtam010793@gmail.com
@@handmadenguyen mashin is the prices
Please send me an email via: nguyenminhtam010793@gmail.com
Hello, I need a drawing of the equipment
Please send me an email via: nguyenminhtam010793@gmail.com
What size is your barrel screw?
D20 friend
@@handmadenguyenand how long is it? coz looks short.
About 280mm
Where buy this barrel screw or diy ?
How much this machin please
Máy này bn tiền vậy bạn?
IB zalo minh nhe: 0915767171
Kitne ki h y
Kitne giram ka pic bar degi y
How much this machin
Ye machine kitne ki hai
???
Price?
Hi
Type of PlC and HMI
I use PLC and HMI Delta
Delta hmi DOP-107VB
Or other
@mostafamagdy3126 yes, this model
and Delta plc DVP 12sa211t
8input 6output high speed
Do you connect between thermocouple and plc and hmi and control
Hey sir great project, I wanna build It my self too, please give me the quote and if possible then can you sell me a full diy kit with the guide to make this my self. I am highly interested in This project. Please contact me
Shut up