Thanks for the instructional video. I managed to replace my old battery and reprogram closing limits. Thanks for saving me a call out and the hassle of getting a repair person.
hi. I have the D5 evo. I have black and red plus ground pillar light cables. I need help how to connect these cables to the controller? currently these are loose in my box and I want my pillar lights to work
Hi , I have installed a D5 Evo some time back but have had issues with the gate opening randomly on it s own. This causes problems for my security company as they are unable to access the premises via the Air Keypad ......when I activate the holiday lockout .
Hi Iam an end user and recently installed a D5 Evo gate motor. Would you please help me with the guidelines in connecting a Commax intercom to the gate motor
i installed a d5 motor for a client, it works perfect except that the gate moves too slow till it crosses the origin marker plus after opening, the gate shifts back slightly as if it wants to close again and stops. what could be the problem.
George Oduro Hello George. The gate will move slowly until it knows its position (by moving the magnet past the origin sensor), so that is normal. There could be a couple of reasons that cause it to want to move back after opening - such as detecting a collision. Please give our Technical Call Centre a call to help you identify what could be causing this. The number is +27 11 699 2481.
I have a problem with my Motor it only works when i press the test button, when i try to set my reciever it doesnt have life does the black small cable have to not be connected anywhere
Hi there. Thanks for your query. No, the thin black cable is the antenna, and doesn't have to be connected to anything. The programming method would depend on the model of receiver/remote that you are using. Kindly give our technical support team a call on 0861 003 123 so that we can help you diagnose the problem.
Bonsoir j ai un problème sur mon motor centurion D5 quand j utilise mon télécommande ou le bouton Exit pour démarrer mon motor l écran affiche No limits SET
Hi, kindly assist. My D5 gate motor shows that it has stalled and when I try to reset the it by setting the gate limiters it says no origin found! Whats the correct procedure to unstall or reset it?
Hi Arthur. Thanks for your message. Kindly give our technical helpline a call on +27 11 699 2481 or send an email to support@centsys.com. Our knowledgeable technicians will be able to assist you with some diagnostic procedures.
I have a D5 evo motor. I have checked all the mechanical limits and followed all instructions. The magnet is also well set but when the motor starts for the first time, before it finishes the full cycle the controller goes off then restarts itself and everything starts over. Can you please assist?
I have a electric sliding gate it works ok for about 20 times then it goes past stop sensor for no reason then I have to reset it again anybody got any ideas
Hi my master remote is working but my other remote not setting up so please can you help me to how to set up bcs I try to hold 15 sacend master remote after I am pressing normal remote but not seting up
+Miles Williams Hi Miles. Thanks for the comment. If you have lost the master, you need to clear the receiver's memory by bridging either J1 or J2 with the middle pin. This will delete all remote buttons. Next, press and hold the remote you wish to make the new master for approximately 5 seconds. Once you have created the new master, press and hold it again for 11 seconds, release it, and then systematically press and release each new button that you wish to learn. Alternatively, you can give our tech support team a call on 0861 003 123. They will walk you through the procedure.
No hablo english y tengo problema con la instalacion de un motor D5 , parte y se para y el visor LCD me dice error en Fuente de Poder, Me puee ayudar alguien
tienes un problema en el cargador, posiblemente este dañado, debes reemplazarlo y listo. o tienes un cable flojo entre la fuente de poder y la tarjeta logica.
Thanks for your important guide to Centurion Motor gate controller!
Installed a motor thanks to this video
thanks fr the video ..gate was stuck..didnt know hw to put on manual...till now:)
It's an absolute pleasure, Dane! So glad that we could help :-).
How is the bracket fitted around the gate motor opening and closing with the key?
Thanks for the instructional video. I managed to replace my old battery and reprogram closing limits. Thanks for saving me a call out and the hassle of getting a repair person.
Gate only opens with a remote.
hi. I have the D5 evo. I have black and red plus ground pillar light cables. I need help how to connect these cables to the controller? currently these are loose in my box and I want my pillar lights to work
Hi , I have installed a D5 Evo some time back but have had issues with the gate opening randomly on it s own. This causes problems for my security company as they are unable to access the premises via the Air Keypad ......when I activate the holiday lockout .
Just sorted my issue....appreciate lots
Hi Iam an end user and recently installed a D5 Evo gate motor. Would you please help me with the guidelines in connecting a Commax intercom to the gate motor
hi . my d3 opens at the intercom inside but not with my remotes. please help
great video and helpful
hi thanks for the relpy
Awesome!
When gate opens it rolls off the rail and falls over , does this have to do with the settings on remote control ?
Very good video.
Nice lecture, mind opening, thank you so much
Very good detailed instructional video .
hi, I am going to build the gate but I don't know how to install opener so I need help, thanks kevin
Hi. I have a problem opening the cover. It is stuck on the side of the gate and also where do I find the power switch. thanks.
My gate motor doesn't want to go to manual D5 Centrion, even when i screw in the knot , it does not want to tighten up,
What could be the problem
Impressive
very clear
Nice explain
i installed a d5 motor for a client, it works perfect except that the gate moves too slow till it crosses the origin marker plus after opening, the gate shifts back slightly as if it wants to close again and stops. what could be the problem.
George Oduro Hello George. The gate will move slowly until it knows its position (by moving the magnet past the origin sensor), so that is normal. There could be a couple of reasons that cause it to want to move back after opening - such as detecting a collision. Please give our Technical Call Centre a call to help you identify what could be causing this. The number is +27 11 699 2481.
CenturionSystems alright thanks.
the gate lying on motor
George Oduro send your contact
Why it keeps open when the program has been done it doesn't stay closed
I have a problem with my Motor it only works when i press the test button, when i try to set my reciever it doesnt have life does the black small cable have to not be connected anywhere
Hi there. Thanks for your query. No, the thin black cable is the antenna, and doesn't have to be connected to anything. The programming method would depend on the model of receiver/remote that you are using. Kindly give our technical support team a call on 0861 003 123 so that we can help you diagnose the problem.
Ok thank you
Bonsoir j ai un problème sur mon motor centurion D5 quand j utilise mon télécommande ou le bouton Exit pour démarrer mon motor l écran affiche No limits SET
Hi, kindly assist. My D5 gate motor shows that it has stalled and when I try to reset the it by setting the gate limiters it says no origin found! Whats the correct procedure to unstall or reset it?
Hi Arthur. Thanks for your message. Kindly give our technical helpline a call on +27 11 699 2481 or send an email to support@centsys.com. Our knowledgeable technicians will be able to assist you with some diagnostic procedures.
Hi, please I will to get info about price and supply. Pepersonaltrainer or 0793775847 samuel
I have a D5 evo motor. I have checked all the mechanical limits and followed all instructions. The magnet is also well set but when the motor starts for the first time, before it finishes the full cycle the controller goes off then restarts itself and everything starts over. Can you please assist?
Check the battery if it's fully charged
Awesome
How to check oil level on dip stick for d5.
Good afternoon. My gate cannot find origin. What to do?
Hi sir I have one question if the motor not reached to moto must be what, only in the motor there's power
well explained
❤
I have a electric sliding gate it works ok for about 20 times then it goes past stop sensor for no reason then I have to reset it again anybody got any ideas
Installation instructions of the D3,D5 sliding gates.
Hi my master remote is working but my other remote not setting up so please can you help me to how to set up bcs I try to hold 15 sacend master remote after I am pressing normal remote but not seting up
Why does the gate open half way and it stops
Thanks
Hi my d5 will nie oop of toe maak nie wat kan vout en waar na moet ek kyk help aseblief
how can i slow down my gate
Hi I'm an end user and wanted to know how would I go about programing new controls if I have lost my master control? Thanks
+Miles Williams Hi Miles. Thanks for the comment. If you have lost the master, you need to clear the receiver's memory by bridging either J1 or J2 with the middle pin. This will delete all remote buttons. Next, press and hold the remote you wish to make the new master for approximately 5 seconds. Once you have created the new master, press and hold it again for 11 seconds, release it, and then systematically press and release each new button that you wish to learn. Alternatively, you can give our tech support team a call on 0861 003 123. They will walk you through the procedure.
Thanks for the help. I appreciate the quick response. Will give this a shot and see
+Miles Williams Awesome! It's an absolute pleasure. Please give us a shout if you don't come right.
GOD IS OHSOME
this is really good have you extended this type of gate to Africa especially to Kenya
Yes we have them in Kenya. Both swing and then slide
please help how to erase the nova remote from the d5 gatd motor
Please contact our Technical Call Centre for advice on +27 11 699 2481
hi i am Theo instruggle I struggle to link the remonte with my motor need assistance
Please contact our Technical Call Centre for advice on +27 11 699 2481
if my master remote is missing, do i reprogram everthing? and how?
ok no problem this jumper open or dip baton 30 ascend or remote dip push
How do I download this video to my phone
the motor is only closing when i press test button but not opening
Please contact our Technical Call Centre for advice on +27 11 699 2481
HI centurion i want to be a distributor in Nigeria and as well install.
No hablo english y tengo problema con la instalacion de un motor D5 , parte y se para y el visor LCD me dice error en Fuente de Poder, Me puee ayudar alguien
Estimada Viviana. Podria enviarnos su direccion email e indicarnos el pais desde donde nos esta contactando?
tienes un problema en el cargador, posiblemente este dañado, debes reemplazarlo y listo. o tienes un cable flojo entre la fuente de poder y la tarjeta logica.
5:21
Good people please always remember all these are man made so don't be intimidated
Por favor lo pueden decir en español
Hi
Español, Spanish .