hey mate, i really need your help, if your dyson v10 is still opened up, can you check how many volts it pulls and at what frequency? i have a motor from a damaged v10, i would really appreciate it if you can tell these values, thanks a lot in advance
Hi, I have the same problem, the filter light keeps blinking even with everything clean, but the motor doesn't spin. Have you figured out what's the issue?
My Dyson v11 keeps pulsing in normal and low power mode, but runs fine in boost mode. That phenomenon started happening from one day to the other. Do you know what could be the reason for that? Do you think there is anything I could do about it? Maybe just cleaning it up somehow? I already disassembled it to the core and now I guess I have to desolder the motor from the PCB to dig even further. Do you think there is something I can do before that to fix the issue?
@@Peppasteppah I had to buy a new core. Of course I cleaned it completely before digging deeper. But it seems the electronics or the motor were defect.
My dyson v11 also pulsing in slow n normal mode but ok in high mode.. tried cleaning it but still pulsing.. I changed the motor and it worked fine in all mode.. probably the circuit board got some faulty components..
@@malcomsue thanks, I see it now, the two large solder blobs in the center (also on my V11). Seems my 30W soldering iron is underpowered, though, I can't melt it 😞
Hello , Do you know how the speed selector works on the small electronic card ? . What technology is used ?
אני גם פירקתי , הציר עשוי מקרמיקה
והגוף עושי מפלסטיק קשיח שעמיד לחום גבוהה ושביר מאוד
good
hey mate, i really need your help, if your dyson v10 is still opened up, can you check how many volts it pulls and at what frequency? i have a motor from a damaged v10, i would really appreciate it if you can tell these values, thanks a lot in advance
nothing to be shocked. single phase BLDCs are widely used for many application.
Hi, I have the same problem, the filter light keeps blinking even with everything clean, but the motor doesn't spin. Have you figured out what's the issue?
Non ha capito niente!
I glued a neodymium magnet to the board in the right spot (corner) and it works.
My Dyson v11 keeps pulsing in normal and low power mode, but runs fine in boost mode. That phenomenon started happening from one day to the other. Do you know what could be the reason for that? Do you think there is anything I could do about it? Maybe just cleaning it up somehow? I already disassembled it to the core and now I guess I have to desolder the motor from the PCB to dig even further. Do you think there is something I can do before that to fix the issue?
Clean out the vacuum, not unscrew it, just wash the filter and brush the metallic grill under the dust container
@@Peppasteppah I had to buy a new core. Of course I cleaned it completely before digging deeper. But it seems the electronics or the motor were defect.
My dyson v11 also pulsing in slow n normal mode but ok in high mode.. tried cleaning it but still pulsing..
I changed the motor and it worked fine in all mode.. probably the circuit board got some faulty components..
What hall sensor is? Numer on it? Thanks
How did you remove the PCB and the motor (center of image) from the housing (top left of image), is the PCB glued in?
The PCB is glued to the housing, however, it is really the solder on the contacts that hold it on.
@@malcomsue thanks, I see it now, the two large solder blobs in the center (also on my V11). Seems my 30W soldering iron is underpowered, though, I can't melt it 😞
v11 motor hears 1 noise when operating, is there any way to fix them
How buy motor in dyson v15
добрый день. могли бы назвать маркировку микросхемы U12 .как она в миру зовётся?
LMV641 (A99)