That is the problem with multi-head emb machines, that no one talks about. When one head is having problems, the whole machine shuts down. Much better to have 6 single heads, so the rest of the heads keep running if one stops. This is the strategy our shop has been following for the last 20 years. PLUS, you can run different small jobs at the same time with multiple single heads, and not tie up the whole 6 head machine for one job. Good luck with your endeavors. 😀
That's just a very expensive road to go down. To have 6 single head TMEZ's is a little under $200k when then 6 head costs $100k. I can still shut down heads if they fail too but I definitely see your point
most multi head machines allow you to turn off heads as needed. also running multiple single heads takes more man power to operate. one operator can run two six head machines yes it will take two people to manage 7-8 single heads.
@@leestuart38Hey here’s a pro tip!! My family has been in the business for over 30 years. We have a tall guy that runs our hat machine, so we raised the machine by using cinder blocks. makes a huge difference and helps the back. i can send you a pic
Just because your car can go up to 200mph doesn’t mean you shoudl drive like that all the time, thats what one OG Tajima tech told me ages ago, keep you machines running no higher than 600RPM, as well when you’re running caps dont run them higher than 500RPM, machine will run smoother less threads break and less problems you’ll have on preventative maintenance, good luck homie.
Happy to see you moving into embroidery. I run two single head ZSK's and multiple singles definitely has it's perks but def a more expensive route to go for multiple machines. But, I don't have to be super precise on hooping since I have some room to move the needle to my start point and being a single person run home shop it's helpful to run different designs/products as needed but as volume increase more heads are definitely needed but I run along quick enough with my two singles for now but plan on adding more singles when the time comes. Keep killing it!
slow down the speed and the lettering, especially the smaller size lettering will look better, even without using a thinner needle and thread. You won't snap thread as much either. Time studies don't lie. Running at 800-1000+ can take longer to complete a large job due to down time. 680 is ideal speed. Produces a better result too, even on cheap apparel.
Hi Lee, My name is Danish and I am from Pakistan, I have 15 years of experience in operating all types of embroidery machines and 24-36 head machines which are very skillful to operate.
Hei Lee, here is Marius from Romania. How big it's your printshop? I'm still surprise that you fit in the shop more and more machineries which also becomes bigger and bigger 😂
Just got a 6 head TMAR KC delivered last week! Noticed in one of your older videos you had a melco sitting around. That is what we currenlty run, and I am hoping I like the Tajima so much better that I can sell every one of them (hopefully no potential buyers read this comment) and go ahead and roll with 2 tajimas.
hello, im from Mexico, thank you for share this video, I just bought 3 months ago a new tajima SAI, machine is good, at the beggining I had the same issue of thread breakage , the techinician checked the machine 3 times, but at the end I think the issue was because I was putting the pre filled bobbin wrong, lol, but now machine even with the max peed 800 RPM, machine flyies. Regards
@@leestuart38 I hear that we are out of room as well. Are orders that were 25-40 pieces are now turning into orders over. Is it booming for you? Do you only do hats or do you do flats also?
Beautiful stitch outs, your new/old hat design looks terrific!! I have two Barudan Pro3’s and when I have problems with the “upper thread break sensor” it’s usually from short stitches. In the settings, I have the ability to adjust the “number of stitches” before it trips the code, not sure if Tajima has the same setting.
Love this! Did you make your money back on the machine first before upgrading? I'm thinking about going the same route as you with the single head first, but then again I don't want to get backed up by jobs bigger that the single head cant handle. Kind of like you, Id rather get the top of the line machines, than waste my time with something that's "subpar."
I made about 75% of it before swapping to the 6 head, and that was in 3 months starting with no embroidery clients at all. It's not a bad idea to start with the single and build up your base, plus it's something you can keep for sampling and small runs. I would have kept mine if I had the space
It's been great watching you grow. When you decided to go with Tajima, did you consider Barudan and ZSK? If so, why did you choose Tajima over them? From what I've seen, they are about the top three brands but I haven't figured out what the major differentiator is other than the proximity of service personnel.
Service is the main factor most should consider. Doesn't matter what brand you run with these things will need service and they will break. Having closely available service is so important to make sure you don't have down time, especially only having one machine. Other than that it does help to choose a brand with a proven track record of quality. Tajima checks both of those boxes for me. I have a tech available anytime in my city and I get peace of mind knowing that there are 30+ year old Tajima machines still in service today producing high level work.
@@leestuart38 Thank you. I figured that the availability of service technicians would be a major factor. Those pesky single points of failure can be an issue but I think you'll have to build an addition to your building before adding a second 6-head machine. :)
Just curious why you didn't have a Hirsch Tech help you set it up. We've used Tajima multihead Machines since we started in 2004 and every machine we've purchased, a Hirsch tech has had us up and running within 24 hours. I'm actually wanting to trade one of our 8-Head TMARK's in for this very machine. Hope it works out for you! Stay Awesome!
I love your videos! We also love our Tajimas. As long as you maintain them and have a good service tech then these machines can run like a beast even as they age. We use the TFMX models 6 head, 4 head and two single heads. I’m really wondering if the TEMZ and the auto tension functions really increase efficiency? Now that you’ve posted this 6 months ago, still wondering if you love your TMEZ? We’re thinking of getting a TMEZ for the next purchase, just a one head.
Been following you on our new embroidery journey, and took your rec and followed Kenblkwrk as well. His vids look like they got taken down by Wilcom, do you know if he’s coming back? You and him should partner up if not!!
You plan on upgrading your hoops too to Mightyhoops? I love them. Badass video man love your content you are living what I'm motivated to own one day! Keep up the grind, you are a inspiration to many.
@@leestuart38 I only have a double head Ricoma, But I will be making the switch to a Tajima soon. I should have just went strait for Tajima but you live and you learn :(
You should sell some raffle tickets maybe give away the Single head away but only with a purchase of tickets or maybe a special embroidery drop hats. I started my company watching your videos I run my company out of my one bedroom apartment so it’d be cool if some of us small business owners would be able to maybe contribute to your company and have the possibility of winning a commercial embroidery machine… 🤔
What are the “little tweaks” you made that kept the machines from stopping? Sounds like they made all the difference since you were able to get through jobs without any issues but you didn’t hint at what the changes were.
Dude watching you grow into this empire is so exciting, I’m launching my brand November 22!! I’ve used allot of your knowledge and tips but I’d love to maybe collaborate with you on a project for real!
Lol hype video... something is off..many already think channel is a fake..did lee pay for machine or did he get for free...the way the chines like to pimp out big channels for advertising..you figure it out...plus tajima aint all that for the price ..i know i actually paid for my machines....shop has 27 years of experience..lee a newbie that has a platform companies jump on ..
Think it's fake all you want, nobody here gives a shit. Take a lesson in spelling and grammar before you come back so people can actually read the nonsense you're trying to type.
@@leestuart38 take heart Lee. There will always be haters. First of all Tajima is Japanese who have been making GREAT MACHINES since when Kennedy was president. The automatic tensioners and digitel presser foot technology in Tajima machines is a game changer that everyone will sooner or later warm up to. In any case, you have done a terrific job of introducing the TMEZ with a BANG!!! to many who wouldnt have otherwise known. Keep up the good job of educating us
lol i work in a factory with 3, 8 heads, 7 6 heads, and 4 single heads. I run a 8 and a 6... the 8 is the only tmez.. the rest are tfmx.. oolder ones and the tmez is sooo nice to have.. but yeah.. shit gets looooud.. but its soothing somehow too haha
The biggest reason to choose the TMEZ is the automatic tension. The up front cost is a lot higher but it is worth every penny. Not having having to worry about tension makes employee training super easy and you can trust there's always a consistent and quality product being made.
You can’t embroidery full back designs because large hoops doesn’t fit on the space provide by a multihead. And when you have to make embroidery name on jackets or any garment you have to do it one by one imagine you have a order of 48 jackets to embroidery a personal names on it. What you will do?
Wrong. This is the stretch model so it can run full back sized embroidery pieces on every head. I leave the personalizations to the crafters running single head machines, there's no money in that for me. We're a volume production shop.
In our shop we run 3 of these- Rough time estimate is for every 1k stitches is 1 minute. 8k 8min etc plus treating the hats etc. Our shop was broken down by marshal Atkinson to be as profitable as humanly possible. Time trials are a must.
Do you have the 6 head Standard or stretch version? Which do you recommend? Also does it come in parts so you can install it or is all big piece of equipment.
I can't seem to find the final video about the single head tmez you were talking about that was posted. Just got a single head tmez so looking for as much information as possible!
OW hell yeah the monster is tamed, let Big Jimmy do the work.😊. Would be very interesting to see some combo screenprint embroidery hybrid design. Make it so 😂
I'm cracking up! My cousin and I grew up like brothers and we were both named Jimmy after our Dads. The family always called him little Jimmy and I'm Big Jimmy. True story. Congrats on the success man. Loving the videos.
Lee, the pads the levelers sit on at the 3:25 mark. Were those provided by Tajima or RB? Or did you buy those? I’m looking for that very thing. Thanks!
You are so inspirational and have helped me grown my business tremendously! Thank you! Now hoping one day that I can upgrade from the single head to a 6 head! Lol
Did you by chance look at the zsk racer r? It can run at 2k+ stitches per min. A 6 head machine of that is equal to running 12 of another that is similar quality.
Just because it can doesn't mean it should. A lot of machines can go fast but most garments can't handle anywhere near that speed and maintain tight embroidery quality. It's just a gimmick.
I don’t know if I would go as far as saying it’s a gimmick. It had stellar reviews at the expo. I know a few tajima owners looking to switch over just for that stitch speed.
This is an amazing machine, but we got quoted almost $91k delivered and we got our brand new 2023 Barudan 6-head Stretch 450x520 for $50.5k so that’s almost 1/2 the price… so we ordered two Barudan 6-head Stretch for the price of one TMEZ Yes, I know it doesn’t have all the bells & whistles that TMEZ has, but Barudan are best known for caps… even Richardson has around 300 Barudan heads in their facility
It's not even close to comparable. The technology in this thing is where the added cost comes from and is decades ahead of the Barudan, and it's worth it. The comparable Tajima machine from their lineup runs the same price as the Barudan
The “comparable” TFMX Tajima was quoted at $75k delivered and still has a smaller embroidery filed than the Barudan at 450x520 Plus embroidery is like driving. Learning how to drive is best on a 1980 manual car without gadgets… just because you can jump on a brand new automatic car with all the new bells and whistles it doesn’t make you a good driver… I know 1000% certainly you won’t be able to solve issues or tweak EMB files because you’re “learning” on your TMEZ… but good luck Don’t get me wrong, it’s an amazing machine, but I bought two brand new Barudan for price of one TMEZ and Barudan is what major companies like Richardson use for their caps
@yehudahweisz3879 that's the thing, I'll never have those issues so there will be nothing for me to solve. You're right it is like driving, and you're comparing a car with a carburetor to one with fuel injection. One costs half as much and makes the purists happy, and the other is modern technology that produces maximum performance without needing constant tuning like the carburetor. The vast majority of operator issues come from incorrect upper tension, presser foot settings, bobbin tension, speed, etc. I only have to worry about bobbin tension and speed at most. Plus I can train literally anyone in a few days to run this thing and they will produce the same quality product that a veteran can. That alone makes the cost worth it
Congrats bro! Shesh! Just when I think I am catching up to you you come out with this lol I look up to you since you and I opened up on the same time 5 years ago
@@leestuart38 sometimes I get worried going back into debt just as I’m done paying for all my machinery how do you mainly get clients without a store front?
Ummm... is the next video going to be of the shop expansion?! The way that you are going, you're going to need twice the size of the original shop soon!! ❤
We looked at those EZ machines, ended up going with Ricoma. Literally the same machine minus the auto tension that’s unnecessary, super easy to work on if needing to replace parts and stitches like a dream. We got 2 of the 1508s for almost the same price as your 1506EZ… 16 heads for 100k vs 6 heads for 82k. They both run like a dream. The only tajima I’d consider getting would be the SHL5 single head with laser for appliqué, but they want 51k for it right now which is absolutely insane. Tajima prices are so high because Hirsch Solutions marks everything up 47% as an exclusive distributor fee…
Ricoma is a good embroiderer but it has no collaboration with tajima, barudan, happy or zsk... Ricoma is a premium china, it has certainly improved a lot and the quality-price ratio is very good, let's say it is like Xiaomi combined with Samsung or Apple
@leestuart38 the laser thing will help so much. I have not used mine for it, but I'm going to try it soon. Right now, I just cut after it sews. You have to be way too close if your satin stitch is not wide.
If you dig them you would like my band, IVSI. I just entered the DTF game this year and am jumping in with both feet. Already thinking of larger formats and pneumatic presses to keep up with my work flow.
Hi there ! any chance you can give me an idea of the price point? I am completely new to embroidery and trying to find out so I can start budgeting towards that goal. Thank you so much ! :)
@@leestuart38 awesome have to watch the vid at home, cause for some reason when i start the vid on my phone i can watch like 1 min and then only commercials, but i will get to see this monster in action.
That is the problem with multi-head emb machines, that no one talks about. When one head is having problems, the whole machine shuts down. Much better to have 6 single heads, so the rest of the heads keep running if one stops. This is the strategy our shop has been following for the last 20 years. PLUS, you can run different small jobs at the same time with multiple single heads, and not tie up the whole 6 head machine for one job. Good luck with your endeavors. 😀
That's just a very expensive road to go down. To have 6 single head TMEZ's is a little under $200k when then 6 head costs $100k. I can still shut down heads if they fail too but I definitely see your point
@@leestuart38Expensive but l believe has its advantages have also seen quite a number of the big shops do the same with multiple single heads.
I said the same thing on the single video. Higher up front cost, lower down time and more profitable long term
most multi head machines allow you to turn off heads as needed. also running multiple single heads takes more man power to operate. one operator can run two six head machines yes it will take two people to manage 7-8 single heads.
@@leestuart38Hey here’s a pro tip!! My family has been in the business for over 30 years. We have a tall guy that runs our hat machine, so we raised the machine by using cinder blocks. makes a huge difference and helps the back. i can send you a pic
Just because your car can go up to 200mph doesn’t mean you shoudl drive like that all the time, thats what one OG Tajima tech told me ages ago, keep you machines running no higher than 600RPM, as well when you’re running caps dont run them higher than 500RPM, machine will run smoother less threads break and less problems you’ll have on preventative maintenance, good luck homie.
Do you want a man who is operating your machine.... My experience is 15 years... And I operate 16 head machine in Pakistan..
Happy to see you moving into embroidery. I run two single head ZSK's and multiple singles definitely has it's perks but def a more expensive route to go for multiple machines. But, I don't have to be super precise on hooping since I have some room to move the needle to my start point and being a single person run home shop it's helpful to run different designs/products as needed but as volume increase more heads are definitely needed but I run along quick enough with my two singles for now but plan on adding more singles when the time comes. Keep killing it!
slow down the speed and the lettering, especially the smaller size lettering will look better, even without using a thinner needle and thread. You won't snap thread as much either. Time studies don't lie. Running at 800-1000+ can take longer to complete a large job due to down time. 680 is ideal speed. Produces a better result too, even on cheap apparel.
I've never run a machine that fast, the fastest I go is 750spm but usually 700spm for most things. The timing was the main issue, it was off
Don’t get too big to where you depend on other people to do the day to day. If you haven’t noticed lately, people suck! They can make or break you.
i agree with you 100%
Merhaba ben de orada çalışmak istiyorum bana bir davetiye yollar mısınız Türkiye’den Amerika hayalim var
Hi Lee, My name is Danish and I am from Pakistan, I have 15 years of experience in operating all types of embroidery machines and 24-36 head machines which are very skillful to operate.
😂amazing 🔥🔥🔥🔥🔥🔥money 🤑
Hei Lee, here is Marius from Romania. How big it's your printshop? I'm still surprise that you fit in the shop more and more machineries which also becomes bigger and bigger 😂
livin' the dream
Just got a 6 head TMAR KC delivered last week! Noticed in one of your older videos you had a melco sitting around. That is what we currenlty run, and I am hoping I like the Tajima so much better that I can sell every one of them (hopefully no potential buyers read this comment) and go ahead and roll with 2 tajimas.
I promise you, you'll never touch your melco ever again once you have the Tajima running
@@leestuart38 training and set up starts today 👍🏻
So what was the final verdict on what was causing the issues?
Timing was the main factor
I wouldn't get rid of Little Jimmy. Small jobs make more money
hello, im from Mexico, thank you for share this video, I just bought 3 months ago a new tajima SAI, machine is good, at the beggining I had the same issue of thread breakage , the techinician checked the machine 3 times, but at the end I think the issue was because I was putting the pre filled bobbin wrong, lol, but now machine even with the max peed 800 RPM, machine flyies. Regards
Hola ¿cuánto es lo que estas pidiendo por tus maquinas?
How's the machine treating you? I just got one at my shop we are all ready talking about getting another
I absolutely love mine, it's been a workhorse. I need a bigger shop so I can get another
@@leestuart38 I hear that we are out of room as well. Are orders that were 25-40 pieces are now turning into orders over. Is it booming for you? Do you only do hats or do you do flats also?
Beautiful stitch outs, your new/old hat design looks terrific!!
I have two Barudan Pro3’s and when I have problems with the “upper thread break sensor” it’s usually from short stitches. In the settings, I have the ability to adjust the “number of stitches” before it trips the code, not sure if Tajima has the same setting.
"if your not pushing forward you are left behind" i felt that right into my soul! exactly my motto! you go hard or you don't go at all!!
Lee you are full of bs
I'm full of brilliant stuff? Thanks!
Love this! Did you make your money back on the machine first before upgrading? I'm thinking about going the same route as you with the single head first, but then again I don't want to get backed up by jobs bigger that the single head cant handle. Kind of like you, Id rather get the top of the line machines, than waste my time with something that's "subpar."
I made about 75% of it before swapping to the 6 head, and that was in 3 months starting with no embroidery clients at all. It's not a bad idea to start with the single and build up your base, plus it's something you can keep for sampling and small runs. I would have kept mine if I had the space
púedo enviarte un diseño para 3d? y ver que pasa?,, me interesa ese modelo pero veo que le falta tecnica a tus diseños, estamos para apoyart
It's been great watching you grow. When you decided to go with Tajima, did you consider Barudan and ZSK? If so, why did you choose Tajima over them? From what I've seen, they are about the top three brands but I haven't figured out what the major differentiator is other than the proximity of service personnel.
Service is the main factor most should consider. Doesn't matter what brand you run with these things will need service and they will break. Having closely available service is so important to make sure you don't have down time, especially only having one machine. Other than that it does help to choose a brand with a proven track record of quality. Tajima checks both of those boxes for me. I have a tech available anytime in my city and I get peace of mind knowing that there are 30+ year old Tajima machines still in service today producing high level work.
@@leestuart38 Thank you. I figured that the availability of service technicians would be a major factor. Those pesky single points of failure can be an issue but I think you'll have to build an addition to your building before adding a second 6-head machine. :)
I am a best opreto you have vacancy?
Thanks for the lesson on the persistence subject.
Love the bloopers, and trials and tribulations. Showing that not everything is perfect is what makes this channel feel grounded.
I appreciate that 🙏🏻. Keeping this stuff real is always the main goal
Hi from Oregon USA .You said how much the smaller machine was. How much is that machine? video and audio quality is good. Enjoy the video.
TMEZ is the bomb! We have 2 of those that you got there and I can't tell you how much less of a headache the tension is to control now.
That's awesome 👏🏻 . These machines make the embroidery side of the business so much easier to deal with
I'm glad the Ferrari shifts into gear now 💪🏼
Also that RL design at the end looks freaking dope
Those first few days were stressful 😂. It's been smooth as butter ever since
Just curious why you didn't have a Hirsch Tech help you set it up. We've used Tajima multihead Machines since we started in 2004 and every machine we've purchased, a Hirsch tech has had us up and running within 24 hours.
I'm actually wanting to trade one of our 8-Head TMARK's in for this very machine. Hope it works out for you! Stay Awesome!
Next upgrade is for sure some magnetic looms, highly recommend!
Been running mighty hoops since the first day with the single head 🤘🏻
I love your videos! We also love our Tajimas. As long as you maintain them and have a good service tech then these machines can run like a beast even as they age. We use the TFMX models 6 head, 4 head and two single heads. I’m really wondering if the TEMZ and the auto tension functions really increase efficiency? Now that you’ve posted this 6 months ago, still wondering if you love your TMEZ? We’re thinking of getting a TMEZ for the next purchase, just a one head.
Been following you on our new embroidery journey, and took your rec and followed Kenblkwrk as well. His vids look like they got taken down by Wilcom, do you know if he’s coming back? You and him should partner up if not!!
Bro 1 machine
Prices $
that machine is crazy, it was stitching each letter in like half a second. another great video!
It's incredible. I love this machine
You plan on upgrading your hoops too to Mightyhoops? I love them. Badass video man love your content you are living what I'm motivated to own one day! Keep up the grind, you are a inspiration to many.
Yup! I got a full set of mighty hoops for it about a week after I shot this video. It's an expensive upgrade but it's totally worth it
@@leestuart38 I only have a double head Ricoma, But I will be making the switch to a Tajima soon. I should have just went strait for Tajima but you live and you learn :(
Is the problem of cutting continuous lines solved? I have the same problem😭
Looking for spares model tmeg-620 .
Namely lcd ,mother card
Hey buddy,
Can this monster embroider a name on a golf bag?
Keep up the sick work bruh!
👊✊💨
You should sell some raffle tickets maybe give away the Single head away but only with a purchase of tickets or maybe a special embroidery drop hats. I started my company watching your videos I run my company out of my one bedroom apartment so it’d be cool if some of us small business owners would be able to maybe contribute to your company and have the possibility of winning a commercial embroidery machine… 🤔
What are the “little tweaks” you made that kept the machines from stopping? Sounds like they made all the difference since you were able to get through jobs without any issues but you didn’t hint at what the changes were.
I hate embroidery, but i'm loving that ROQ US shirt!!!
So it definitely paid off when you got Little Jimmy for Nics, now you bought Maxi Jimmy, Win Win for both sides, good to see your business growing.
Dude watching you grow into this empire is so exciting, I’m launching my brand November 22!! I’ve used allot of your knowledge and tips but I’d love to maybe collaborate with you on a project for real!
Amazing work! Give me the baby Jimmy, would love to have it!
I love ur machine, dang..no money to buy..😅😅😅
Lol hype video... something is off..many already think channel is a fake..did lee pay for machine or did he get for free...the way the chines like to pimp out big channels for advertising..you figure it out...plus tajima aint all that for the price ..i know i actually paid for my machines....shop has 27 years of experience..lee a newbie that has a platform companies jump on ..
Think it's fake all you want, nobody here gives a shit. Take a lesson in spelling and grammar before you come back so people can actually read the nonsense you're trying to type.
@@leestuart38 take heart Lee. There will always be haters. First of all Tajima is Japanese who have been making GREAT MACHINES since when Kennedy was president. The automatic tensioners and digitel presser foot technology in Tajima machines is a game changer that everyone will sooner or later warm up to. In any case, you have done a terrific job of introducing the TMEZ with a BANG!!! to many who wouldnt have otherwise known. Keep up the good job of educating us
How much is this machine and i need a single head for a start. this is awesome
Quality of white tread on babbin has to be good. When it breaks try to find stronger one
I know the frustration believe me. Its all ways on hats
I see building #2 being added to your property very soon.
A laser bridge would take that beast to a whole new level, doing appliques will be a breeze.
lol i work in a factory with 3, 8 heads, 7 6 heads, and 4 single heads. I run a 8 and a 6... the 8 is the only tmez.. the rest are tfmx.. oolder ones and the tmez is sooo nice to have.. but yeah.. shit gets looooud.. but its soothing somehow too haha
I can't imagine the sound of that many heads running at once, 6 is loud enough in my little shop haha
Amazing video with a fabulous TMEZ! Is there any reason for chose TMEZ instead of TMAR ? Thanks!
The biggest reason to choose the TMEZ is the automatic tension. The up front cost is a lot higher but it is worth every penny. Not having having to worry about tension makes employee training super easy and you can trust there's always a consistent and quality product being made.
14:28 the small text LAC DU BONNET MANITOBA. What needle size you using for that?
Standard 75/11
Did you deal with Jenny from RBDigital?
Congrats!
I deal with Zack and Kevin over there, but they have an awesome staff. RB digital is great to work with. Thanks!
You can’t embroidery full back designs because large hoops doesn’t fit on the space provide by a multihead. And when you have to make embroidery name on jackets or any garment you have to do it one by one imagine you have a order of 48 jackets to embroidery a personal names on it. What you will do?
Wrong. This is the stretch model so it can run full back sized embroidery pieces on every head. I leave the personalizations to the crafters running single head machines, there's no money in that for me. We're a volume production shop.
How long does it take to do a single hat? I know it depends on the stitch count but on an average.
It's impossible to say because stitch counts vary a lot. One hat could take 3-4 minutes, the next could take 30 minutes.
Thanks. Was looking at getting a machine but doing a single hat at a time seems a bit slow. Not sure there is any money in that. Or am I wrong?
@@andrewrobinson6703I made good money with the single head, but obviously a multi head is a lot more profitable
@@leestuart38 thank you.
In our shop we run 3 of these-
Rough time estimate is for every 1k stitches is 1 minute. 8k 8min etc plus treating the hats etc. Our shop was broken down by marshal Atkinson to be as profitable as humanly possible. Time trials are a must.
Do you have the 6 head Standard or stretch version? Which do you recommend? Also does it come in parts so you can install it or is all big piece of equipment.
Stretch version. Always get the stretch
Another awesome video! 👍👏👏👏
What you can try lowering your speed to about 600 /650 rpm helps with tread breaks
The speed was not the issue, it was the timing
living the dream
Working towards that every day 🤘🏻
Buenos videos, tienes de todo, saludos desde Nicaragua.
I can't seem to find the final video about the single head tmez you were talking about that was posted. Just got a single head tmez so looking for as much information as possible!
It's the last video I posted before this one
Keep grinding bro!!! Looking to get a tajima soon does it really stitch out better than the Melco asking because I’ve only ever stitched in Melco.
The difference is massive in all aspects. It's like comparing a Kia to a Lamborghini
OW hell yeah the monster is tamed, let Big Jimmy do the work.😊.
Would be very interesting to see some combo screenprint embroidery hybrid design.
Make it so 😂
I have some ideas brewing
Love how you grow over this years ❤️ 💛 💙.
I'm cracking up! My cousin and I grew up like brothers and we were both named Jimmy after our Dads. The family always called him little Jimmy and I'm Big Jimmy. True story. Congrats on the success man. Loving the videos.
That's awesome 😂
I wouldve gone barudan over tajima just based on the service aspect - im also running single heads for sewouts and onsie twosies jobs
There's no barudan support here. I have a Tajima tech 15 minutes away
Hybrids, now you’re talking my language.
I've got some cool ideas 💡
Dig your hat sick font and keep up the killer jobs man 🤘🤘
Thanks dude 🤘🏻
A laser bridge would take that beast to a whole new level, doing appliques will be a breeze.
Too bad those things cost nearly as much as my entire shop 😂
Fantastic machine bro
I love this guy!
Hey brother what are your presser foot settings dialed too?
It's automatic in this machine
Lee, the pads the levelers sit on at the 3:25 mark. Were those provided by Tajima or RB? Or did you buy those? I’m looking for that very thing. Thanks!
They come with the machine
@@leestuart38 dang. I have a Barudan and while a great machine, seems like Tajima is always a step ahead of them.
BADASS MACHINE ALERT!
You’re the man 💪🏽💪🏽🔥🔥🔥
You are so inspirational and have helped me grown my business tremendously! Thank you! Now hoping one day that I can upgrade from the single head to a 6 head! Lol
So happy to hear that. Thank you 🙏🏻
Did you by chance look at the zsk racer r? It can run at 2k+ stitches per min. A 6 head machine of that is equal to running 12 of another that is similar quality.
Just because it can doesn't mean it should. A lot of machines can go fast but most garments can't handle anywhere near that speed and maintain tight embroidery quality. It's just a gimmick.
I don’t know if I would go as far as saying it’s a gimmick. It had stellar reviews at the expo. I know a few tajima owners looking to switch over just for that stitch speed.
This is an amazing machine, but we got quoted almost $91k delivered and we got our brand new 2023 Barudan 6-head Stretch 450x520 for $50.5k so that’s almost 1/2 the price… so we ordered two Barudan 6-head Stretch for the price of one TMEZ
Yes, I know it doesn’t have all the bells & whistles that TMEZ has, but Barudan are best known for caps… even Richardson has around 300 Barudan heads in their facility
It's not even close to comparable. The technology in this thing is where the added cost comes from and is decades ahead of the Barudan, and it's worth it. The comparable Tajima machine from their lineup runs the same price as the Barudan
The “comparable” TFMX Tajima was quoted at $75k delivered and still has a smaller embroidery filed than the Barudan at 450x520
Plus embroidery is like driving. Learning how to drive is best on a 1980 manual car without gadgets… just because you can jump on a brand new automatic car with all the new bells and whistles it doesn’t make you a good driver…
I know 1000% certainly you won’t be able to solve issues or tweak EMB files because you’re “learning” on your TMEZ… but good luck
Don’t get me wrong, it’s an amazing machine, but I bought two brand new Barudan for price of one TMEZ and Barudan is what major companies like Richardson use for their caps
@yehudahweisz3879 that's the thing, I'll never have those issues so there will be nothing for me to solve. You're right it is like driving, and you're comparing a car with a carburetor to one with fuel injection. One costs half as much and makes the purists happy, and the other is modern technology that produces maximum performance without needing constant tuning like the carburetor. The vast majority of operator issues come from incorrect upper tension, presser foot settings, bobbin tension, speed, etc. I only have to worry about bobbin tension and speed at most. Plus I can train literally anyone in a few days to run this thing and they will produce the same quality product that a veteran can. That alone makes the cost worth it
It’s BIG BOI szn
What you going to do with the single machine?
I traded it in toward the 6. Would have liked to keep it but I don't have the space
Do you digitize yourself or outsource this?
Outsource
icho iocho
cant wait
Noisy aren't they, when running together
It's definitely not as loud as other 6 heads that I've been around, but it still sounds like a small helicopter 😂
Congrats bro! Shesh! Just when I think I am catching up to you you come out with this lol I look up to you since you and I opened up on the same time 5 years ago
Always pushing forward. I feel like I'm just getting started
@@leestuart38 sometimes I get worried going back into debt just as I’m done paying for all my machinery how do you mainly get clients without a store front?
what needles you use in small detailing?
75/11 for everything in this video
Ummm... is the next video going to be of the shop expansion?! The way that you are going, you're going to need twice the size of the original shop soon!! ❤
That's my main goal that I'm working towards right now. Definitely going to make that happen within the next year🤘🏻
@@leestuart38 that’s awesome!!! Film that too, please?!
@@devotedbrand I absolutely will be once I know more. I'll be documenting everything
We looked at those EZ machines, ended up going with Ricoma. Literally the same machine minus the auto tension that’s unnecessary, super easy to work on if needing to replace parts and stitches like a dream. We got 2 of the 1508s for almost the same price as your 1506EZ… 16 heads for 100k vs 6 heads for 82k. They both run like a dream. The only tajima I’d consider getting would be the SHL5 single head with laser for appliqué, but they want 51k for it right now which is absolutely insane. Tajima prices are so high because Hirsch Solutions marks everything up 47% as an exclusive distributor fee…
My guy... the TMEZ auto tension is amazing. You don't know what you're missing. My downtime is very low and no talent required to operate it
Ricoma is a good embroiderer but it has no collaboration with tajima, barudan, happy or zsk... Ricoma is a premium china, it has certainly improved a lot and the quality-price ratio is very good, let's say it is like Xiaomi combined with Samsung or Apple
When a ricoma can run 15-20 years let me know.
Good stuff man i really need another machine but need the room 1st. I just did a cool one off appliqué job for my personal self came up so nice.
I still haven't done any appliqué yet, I plan on figuring that out soon
@leestuart38 the laser thing will help so much. I have not used mine for it, but I'm going to try it soon. Right now, I just cut after it sews. You have to be way too close if your satin stitch is not wide.
Cool to see you giving Sylosis some love. Good luck with Big Jimmy!
Been one of my top 3 favorite bands since they dropped conclusion of an age 🤘🏻
If you dig them you would like my band, IVSI. I just entered the DTF game this year and am jumping in with both feet. Already thinking of larger formats and pneumatic presses to keep up with my work flow.
You are still our hero
Selling the single head?!?!
It was traded in
HOW MUCH DOES THE TAJIMA COST
A lot 😂
Man that thing is impressive!
It really is. The auto tension and presser foot make it a dream to work with, and the output is insane
My TMEZ from RB gets delivered tomorrow :) Very excited to add it to the fleet!
Hell ya congrats! You're going to love it
Hi there ! any chance you can give me an idea of the price point? I am completely new to embroidery and trying to find out so I can start budgeting towards that goal.
Thank you so much ! :)
Hi.
What type needle do you guys use for hats?
I use a 75-11 for hats and most things. Some will bump up a size to help with thread breaks I hear, but I've never really had that problem.
Thanks i was using 75/11 and my needle kept breaking. They told me to try 80/12 sharp not ball point
hi im embr
sell me the single head
It was traded in on the new one
Can't wait to see this monster in action.
It's such a beast!
@@leestuart38 awesome have to watch the vid at home, cause for some reason when i start the vid on my phone i can watch like 1 min and then only commercials, but i will get to see this monster in action.