THE DAILY FORD F250 5.4 TICKING/KNOCKING DIAGNOSTICS AND REPAIR
Вставка
- Опубліковано 7 вер 2024
- In this video I troubleshoot and repair my ford f250 5.4 motor that was ticking/knocking very bad.
check out the frostbite ram store for cool tee shirts and merch
teespring.com/...
instagram@frostbite_ram
facebook@frostbite ram
frostbiteram.com/
I honesty like these motors. Pretty easy to work on AND the issues are well documented so you can know what to prepare for maintenance wise. I have no shortage of tutorials online when I have question. Thanks for the video..still relevant today!
Very true!
This project is in my near future 😑 5.4 e150. Nice to have the hood room. Wish me luck. 🔧
Man oh man. You saved me so much grief. Found the number 6 plug and boot a bit loose. Made the adjustments and now Purring like a kitten over here brother!!! Thank you👍🏼
Awesome 👍
Thank you thank uuuu
U save from several hundred I did too check # 5 sparkplug was loose tight it, cranck it and wallllaaa like new
Thank u again.
😂😂 I tell my customers they need new timing chain and vct solenoids then I just replace the plugs 1500 cash in my pocket for 150 dollars of parts😂😂😂😂
❤❤thanks for u from Iraq after 4yrs of this video
Video ABSOLUTELY helps me out ('06 Ford F-150), wish you showed how to get the cover out but I'll manage. My tick is on Driver side... fired it up to tow my trailer and heard it right away (Damn!) I will check my plugs though, and see if that does it... otherwise, I'll be changing all rollers and lifters just like you!! Cant wait to hear my girl purr like that again!!!
any luck? I have the same year and engine, and on the left side.
Son of a mother! No more lifter drama!
Right🤣hopefully I'm good for awhile.
The 2 valve spark plugs are notorious for becoming loose over time. Exhaust gasses build up on the threads. Especially if they were under torqued when installed.
Looks like this is for the 2-valve. The 3-valve engine you do need a tool to take out roller follower and need to take out the cam for removal of lifters.
That would be caused from low oil feed, where the lifter has stuck . By Keeping the oil clean and regular oil changes BEfore fords recommendation time interval will help prevent such condition. One of my lifters was starting to make noise and I gave some WD40 treatment and the lifter quieted down quite a bit, it still is a bit noisy but it definitely helped. I used a cap from a tide bottle - pre-measured two cap fulls and it definitely helped. Varnish is a very big problem to these engines and thinning oil too - so I run 5W30 in the winter and 10W30 in the summer I wont use 5W20 any more as oil pressure is vital to these engines...But a clean engine will save you a big bill down the road..
It should also be noted that - the passenger side will always be problematic due to the way the flow of oil goes which is from the driver side to the passenger, the Driver side gets first shot at the oil then the passenger side. Also maybe invest in a higher volume oil pump { HV140 to HV160} would definitely be a worth it and save your engine...Update here.
If you find the ticking sound only happens when hot and not when cold at startup then it is a valve lash adjuster as- I found on mine - but still dont let it go too long ...
I’ve done the same but with diesel and had a final idle flush of just diesel no oil and it was no louder than with the oil that was in it
5w 30 motor craft oil ever3 to 5 thousand miles, no problems.
Unrelated, but you tried pulling that f26 fuse and seeing if it makes your 0-60 faster? It’s abs and traction control and I absolutely blow the tires off now lol it has zero torque management! Tc button only works so much I realized wish I had tires to hook so I could really test the times I’m pretty sure putting down full power now ha
Oh I guess it might be spark plug? interesting. Good work
Will be changing my plugs this week. Thanks
Good luck!
Awesome Frostbite《☆》I've heard of the 5.4 sparkplug issues. Man what a moneymaking genius came up with those spark plugs :*: I inherited a Motorhome with a Triton V10 & it took me 5 months to work all the bugs out of it so me & my sister could sell it. It was fun to drive but money was tight back then🤓☻🤠
Definitely, I bet that v10 loved gas also 🤣
Imagine a world where you could sell something to someone with the promise of fixing it but using the money from the sale or where you can take an advance on the sale or a loan specific to repair with intent to sell
AWSOME job nice and smooth also learned something.
Ok !! Awesome video I have a 2006 f150 3v I have fixed a few noises and what’s left is a tick that sounds just like yours I think I need to pull the valve covers and check these like you did I put new updated vct solenoids and that fixed the scary hot idle knock I also did new updated spark plugs Hopefully none are loose Yet shouldn’t be since my mechanic did them The tick goes up with rpm It’s annoying Not very loud I’m thinking it could be one of these followers !!!
Very well could be another common issue is worn timing chain or broken tensioner.
I'm not doubting you but that noise surely sounded like a bad lash adjuster, which u solved. Was spark plug in same cylinder as bad adjuster? Thank you bub. God bless
Yeah the spark plugs seems like they need to be torqued and check in a couple thousand miles
I replaced the lifters, the followers and both timing chains on a V10 6.8L and the truck is still making that same knock/tick!
Check for loose spark plug
Try to check the spark plugs r tight enough. Wonder just a little loose and makes a ticking sound
I have heard it several times lol, they are also known for rod slapping too
I have same knocking on 5.4L, would loose lifter cause hesitation and not able to go overdrive/shift when pushing gas hard? but it shifts normal if I barely pushed on gas but as soon as I give it hard gas push it would hesitate or not even go overdrive and shift.
I bought from Ford Canada at 16$ each.. qty 12
But when I went to change the phazer ant rocker arm ,the found one timing chain guide broken,so replace timing chain guides , timing chain phazer solinoid ...etc etc ..
But I had all parts except was missing 12 lifters,so because I bought from the dealer where I was doing the repairs they charge me 48 $ Dollars each..
So the message once you start the work be sure you have all the parts.
Work cost me $5,500 ,even I brought phazer, camshaft rocker arm and 12 lifters..
Now is turning like almost New...
Do you have a video on removing them? Do I have to remove my cam shaft?
Yep. Does the same on a Hemi. Tech left them loose. Sounds like a wrist pin knock.
Yea that's crazy how it sounds definitely easy to point in the wrong direction.
The 5.4 is a good engine, but has two inherent design flaws
1) The spark plug change intervals need to be reduced from 100k to 33k. The higher interval allows for too much carbon buildup. Second the plugs need a 500 to1000 mile re torque after initial install
2) The OEM cam chain tensioner gaskets are prone to failure. This results in low oil pressure on the RH (Passengers) cylinder head. Mechanical components on that cylinder head fail due to minimum oil pressures from the leaking cam chain tensioners. This manifests itself as ticking mechanicals on the RH bank.
The good thing is if caught in proper time, both these issues can be successfully resolved and the engine will no longer experience the issue, while providing another 150 to 200k service life.
Most definitely 👍
Will oil pressure loss caused by the cam chain tensioner show up on my gauges?
If you think about it, every issue on these engines is the heads or attached to them, including the tensioners leaking and the cam bearings bing non existent and this non replaceable, they should have machined in provisions for off the shelf or custom bearings from the beginning or made replacement heads so cheap that it’s acceptable to just pull them and swap all the old components and rebuild the head, realistically considering many new seals would also be needed the price should be somewhere under $100 after core refund, regardless of cost to manufacture as it’s a them problem not a customer problem
when you went to put the new lifters in, did you do anything to them out of the box before they went in? I've heard soaking them in oil for a night and some people have mentioned bleeding them, I'm not sure what to do yet, I got mine out and found 2 bad ones and have the replacement parts ready to go in
I just put them in and lubed them
I think those are lash adjusters, not lifters, right?
I have a 2009 f150 5.4. Doing the same thing on the same side but it's also less power and gas mileage has gone way down, shop says it's a lifter causing it. Have you heard of lift tick causing that as well?
I fixed a truck at work that was doing what you described. Big lack of power and constant ticking on the passenger side bank. I found a seized roller follower that had a flat spot on it but luckily the cam was still salvageable even though it had been driven that way a couple months. Ended up replacing all the roller followers on that bank and it’s quiet with full power again.
Hey I have the same engine and a f250 xl anyways what a knock sensor make that noise also and also I have one I believe it's knock sensor going straight down in the middle between all the valve covers in the top of the block right by I think a water pump hose and then I have a temperature sensor I believe what it is with the wire running over your heater engine coolant hose the big one coming off the radiator well what sensor has one wire running to it just down by the exhaust manifold going into the engine block on driver side? And if that sensor is bad could that make the vehicle have a ticking noise cuz I'm losing power when I try to go up hills it'll go way down and power and then it tries to shift down shift way up and RPMs and still no power to go forward
can those lifters cause a camshaft position code ?
Great video. My 5.4 is tapping like that. On rt
95 heading to FL today. Also, notice that when you stop after a drive, the front end shakes and vibrates. Press the gas its going away. Was the vibration happening on your truck? Much appreciated!
I have the same problem. When I go - everything is fine. But when I stop - it clicks and does not work smoothly
Did you ever figure it out ? My truck got the timing front end rebuilt it idles good but when i slow down and let ofd gas sometimes it shakes and knocks
My 2010 navigator had the same issue. You need to change your VCT solenoid.
Nice
Thanks for posting
What would you look for if you replaced all the lash adjsuters and roller followers, put it together and it still ticked, took it apart on the front and verified the timing components look good too replace the plastic tesioners with new melling metal ones (and high volume output oil pump), put it together and still ticks. . . .? It ticks at idle, but goes away at about 900-1100 rpm and returns when rapping it up above about 2300. When I start it it will tick tick tick loud until I put it in drive, then it quiets considerably. Any ideas? A stethoscope on the engine sounds very metal-on-metal tick, not a poof like an exhaust leak.
Check the exhaust manifold
@@darrencampbell4826 Is all good, not an exhaust leak.
Ok I missed the part on how you removed the lash adjuster without removing your camshaft COMPLETLY??
The ol pop em out screw driver trick
When my 2000 v10 does it.. 250,000 miles like my older cars.. run 1 transmission fluid for a few miles.. then change the oil.. problem solved
Great video 👍
You know the Hemi,s are know for the Hemi( tick)
How are the rockers put back in? I suppose prying them off doesn't work on the Three Valve, nor just pulling out the lifters, right? I just ordered a valve spring compressor and it was surprising how they can be popped off like that, on a Two Valve.
They pop right back on pretty easily
Sounds like a cracked exhaust manifold.
Ticking noise is spark plug or glow plugs!! I don’t understand why some people think are the valves or injectors
Great video bro!👍
How long did it take you to replace all roller and followers?
It's doesn't take long especially if you get the tool that just lifts them out. It is certainly a do it yourself job with the right tool 🔧
@@operationbs7610 what tool did you use and did u purchase that tool on Amazon? Thx for your time!
@@operationbs7610 how much u think sumthing like this will cost cause I got the same problem
@@operationbs7610 can u fixs minds
Did you have to rotate the crank to pop any of the rockers off?
It does help some times to get the spring pressure off.
How much you charge to do a job like that
Is that a 3 valve...?
Are those lifers soild or hydraulic
Thanks good show
2v
Do you have to have the cam in a certain position to pop the roller follower out..? Or does it just pop out in any position the cam sits.
With the spring not compressed
@@FrostbiteRam Thank you! 👍
How hard of a job is that do for someone with novice mechanical experience and how long did it take you?
I'll be doing mine in about a week, perhaps this weekend on my 99 F250. I suggest do the driver side first as there's a lot more room and less stuff to remove to make room. That will prep you to do the passenger side after the driver side is reassembled. I'm a novice-intermediate mechanic, so I'm trying to watch as many related videos as possible. Perhaps you should record video of what you take apart making note of every bolt, from where etc in case you forget anything and have to do more research midway in. That way you can watch your recording and get everything back where it's supposed to be. Also, it's helpful to have a piece of cardboard, marker and a screw driver to poke holes, then you can push the bolts in the hole and jot down where it came from.
Not long really
What spark plugs are good for those 5.4 tritons? Just purchased a mint 2001 F150 Harley Davidson!Thanks
Motorcraft
@@matthewalvarez2741 always!
Have you had a 5.4 bottom end go out before? Mine started knocking. But it sounds way louder than yours
Not on mine
I thought the bottom ends were really tuff . Gonna tear it apart tmrw
Camshaft or race of man?
Did that tick noise go away after it warmed up??
No
Did u pull alll the followers without rotating the cam?
Yes pretty much you can
shit the 5.4l normally have the problem with the spark plugs not wanting to come out hahaha
Right, mine is a 2v so I think I'm good there 🤣lol
What year is your pick up??
2001
That's why they're called a 5.4 ticker lol.....
Sounded like exhaust manifold to me
Is this about mongolians or a camshaft?
IF YOU GAT A FORD JANK IT