Bro I have a doubt allowable stress irukkillaya...7.77 page le...athukku mele ungalkku kgf/mmsqr nu pottu irukku aaana ennode psg le same value N/mmsqr le pottu irukku appo ennode printing mistake aaaaa?????plz reply
Hi brother, a good video but there ia a small unit conversion mistake in step 6 when calculating the bearing stress. In that all other are in mm like area and all but the power we enter is under Nm/s and also the speed is in m/s. There ans is chaninis safe but the cacluated value is wrong brother so kindly make sure that is made correct.
One more doubt ...factor of safety..table le irundhu edukkumbothu...up to 15.875 pitch varakkum than irukku athukku mele ponaaa.. breaking load calculate pannathukkana pitch enge irundhu kidakkum.....I expect you will answer all my questions..pls I have University exam day after tomorrow....
@@focusacademylectures Bro factor of safety table I'll naama pathaaaal....pitch endra coloum irukkillaya...athile...3 pitch values are there....9.525...12.7...15.857...ithile eethavadhu Oru pitch namma chain KU irundhaal Thane....andha coloumn use panna mudium...if my chain have pitch other than above how can I find the factor of safety for calculation.....page 7.71..7.72 paaarungeee....38.10 mm varakkum pitch irukku....aaanal andha box le...moonu pitch values kku aanaa... factor of safety mattum than irukku....?????
Especially its on gear ratio.. same diameter na speed ratio 1.. speed ratio high na torque kammiya irukum.. we have to give more effort.. cycle la speed ratio romba kammiya iruku so effort kammiya kuduthale fast ah pogum.. sprocket dia meter.. affects the effort .. torque affect panum
@@focusacademylectures bro page number 7.72 le irundhu chain select paanalaam illayaa...between two pitch values ...appo andha table leee single chain values...R1548...R1564..R50..Indha 3 values than edukka mudium nu sonningeee...aaanal....R1595...R60 ...ithum edukkkalameee..endrathu than enakku doubt....
Sir unga punniyathulaa na dome la pass aiten thanks a lot sir 🔥🔥🔥
Welcome 🤗🤗
Thank you sir for sharing your valuable knowledge because of your videos i wrote my dts exam well please keep supporting us .
Super thala Vera level sir thank u very much all the. Best keep it up sir❤️❤️❤️
Sir ungaloda video easy ah eruku sir please more video upload pannunga sir
Amazing video! Would like to see more of these
Anna step 6 (checking for bearing stress)
Bearing area 0.7cm² = 0.7*10^-4 m² thaanu varum
Mathan Kumar 0.7 cm2 = 0.7 *10^2 mm2
idk youll read this , but thank u soooo muchh
Yu are welcome.
Sir please upload the videos in English these are too awesome notes what you make.
Really too inspiring.
Thank you sir
this is helpful and
I want design of power screws lecture
Thala mass uhh thala nee 🫡🫡🔥🔥
You are Doing extraordinary bro ...... Super thala.......
Hi sir, well-explained thank u very much.pl, do some more different kinds of design problems like inclined and vertical transmission problems.
Super sir. This video is very usefull for exam.. thanku you sir
Bro I have a doubt allowable stress irukkillaya...7.77 page le...athukku mele ungalkku
kgf/mmsqr nu pottu irukku aaana ennode psg le same value N/mmsqr le pottu irukku appo ennode printing mistake aaaaa?????plz reply
Bane s printing mistake ah iruklam
Thanks a lot, That was so much useful.
Hi brother, a good video but there ia a small unit conversion mistake in step 6 when calculating the bearing stress. In that all other are in mm like area and all but the power we enter is under Nm/s and also the speed is in m/s. There ans is chaninis safe but the cacluated value is wrong brother so kindly make sure that is made correct.
Okay bro
Super thank bro
super sir, and please upload the gear box design problem sir.
Thanks for the explanation guruji
Super bro....6th sem Ella subjectkum apdiye......konjom..
Good video easy understand bro
Sir onga videos ella romba usefulla iruku......wil share as much.
You should do a lot more videos like this
Hello this is a very nice explanation. But my driver gear is driven by a stepper motor. I have only torque value, no power
U can apply torque in power formula.
Sir in some problems speed reduction ratio is given as 2:5:1..how to calculate Z value through this value sir??
Can you give link to tables used in this example?
Super bro
Very useful
Sir your explanation is very good but pls add english or hindi subtitles
Super sir
One more doubt ...factor of safety..table le irundhu edukkumbothu...up to 15.875 pitch varakkum than irukku athukku mele ponaaa.. breaking load calculate pannathukkana pitch enge irundhu kidakkum.....I expect you will answer all my questions..pls I have University exam day after tomorrow....
Bane s athukumela poga kudathu
@@focusacademylectures Bro factor of safety table I'll naama pathaaaal....pitch endra coloum irukkillaya...athile...3 pitch values are there....9.525...12.7...15.857...ithile eethavadhu Oru pitch namma chain KU irundhaal Thane....andha coloumn use panna mudium...if my chain have pitch other than above how can I find the factor of safety for calculation.....page 7.71..7.72 paaarungeee....38.10 mm varakkum pitch irukku....aaanal andha box le...moonu pitch values kku aanaa... factor of safety mattum than irukku....?????
Athukumela ungaluku pitch vantha.. u increase ur factor of safety... Proportionally
Bevel, worm and cross section gear vedeos make it sir!!
Super
Bro. I have a doubt. If the center distance of the sprocket is 2200 mm means, how can I choose a standard pitch..?
Guruji ippo 2 sprocket same dia meter iruntha power transmission eppadi irukum
shivanesh kutty it doesn't affect the power transmission. Same speed la rotate agum.. power transmission ah affect pana vera nerya factors iruku..
Especially its on gear ratio.. same diameter na speed ratio 1.. speed ratio high na torque kammiya irukum.. we have to give more effort.. cycle la speed ratio romba kammiya iruku so effort kammiya kuduthale fast ah pogum.. sprocket dia meter.. affects the effort .. torque affect panum
@@focusacademylectures thank you ji
thank you sir
17 regulation bookla neenga nadathunathu konjam thaan erukku sir some other different sir yapdi padikkirathu sir
Bro, which book your refering the standard values please tell the book name
Psg design databook
Which design data book did you used?
Psg publication
Bro can I use this video pls tell me
use.
Bro pls upload engineering graphics many student of the use that
Hi sir chain drive problemla 17 regulation bookla breaking load kudukkave ella sir athukku pathila design load erukku sir epdi podalaama sir
Na teach panra procedure la panunga., Ne mention panuna sum ah comment la podunga na solren
@@focusacademylectures ok
Do a disc spring problem sir, request
bro GDJP KU apdiye video podunga bro
Thala inum adigama videos podupa
R1595..R60 koode edukalameeee...appadinu nu oru doubt???? But u said there is only three values...Plz rply
Bane s purila
@@focusacademylectures bro page number 7.72 le irundhu chain select paanalaam illayaa...between two pitch values ...appo andha table leee single chain values...R1548...R1564..R50..Indha 3 values than edukka mudium nu sonningeee...aaanal....R1595...R60 ...ithum edukkkalameee..endrathu than enakku doubt....
Athuva simplex dublex and triplex nu chain types.. ethunalum edukalam.. first simplex eduthu sefe aachuna ok.. ilana dublex edukalam.. no issues
Anna pass panniten romba thx
Pls pls snd yor tez number
When you put everything in metre in bearing stress calculation, how will you get the unit kgf/mm2? Step VI??
Units followed based on data book
Sir I need rope procedure and problem please
Hi Sir, Can you mention please name of refer book ?
Psg design data book
Bro will you upload the document (PDF) type problem
Singaravelan Velan yeah i ll upload pdf too
which website bro
Ovoru video ku keela links kuduthurpen
@@focusacademylectures ok bro
Thankyou so much
Hi
Hai
Chain drive la Vera problem pls
Chain drive la oru problem podhum... Vera madhiri ketkamatanga. Goven datas venumn differ agalam
Bro please upload the rope drive problem solving procedure
Singaravelan Velan tomorrow morning it ll be uploaded
@@focusacademylectures Thanks bro
i really need this notes copy.....hehe
himani dwivedi notes on description dude
Unit conversion video vennum bro!!
Ithulayae solirpen.,
@@focusacademylectures One separate unit conversion video only vennum bro
Will try
n2 value bro
Sir...please refer me a book for design of transmission systems🙏🙏
jalaludheen
Gdjp yum poduva sir
i know design related subjects.... not thermal
Sir please upload this lecture in hindi