Novatec F482SB-SL Bearing Replacement
Вставка
- Опубліковано 13 гру 2024
- This instruction shows how to replace bearings in hub F482SB-SL and other Novatec hubs which use the same or similar axle system with axle Ø15mm, like D712SB, F742SB, F682SB, D632SB. Similar procedure also applies to hubs with Ø12mm axle, like F162SB, D042SB, D812SB, F062SB.
A few tips: don't tap on the inner race of the bearing. Bearings of the axle don't need to be tight, only snug in place. When the axle play inbetween the bearings disappears that's perfect! Don't tighten the end caps of the axle too much, snug is enough. Otherwise the bearings will wear out too quickly do to *excessive preload* ! Keep in mind that the quick release also compresses the axle a little so these end caps need little preload.
The 6901 bearing on the axle is the weak point. I'm currently testing if a 6901 *LLU MAX* bearing will last longer.
Thanks for posting, very handy. Any tutorial showing bearing replacement in the cassette (freehub) body?
Remember, do not reinstall bearings after impacting the inner race as the shock transmitted through the rolling elements can cause microchips on the bearing surfaces. This is the only way to get the bearings out of this type hub so, have fresh bearings ready. When reinserting, contact the outer races only. This was done for demonstation purposes. Please share info on the kit used here; it looks awesome!
+twosence fromcleveland
If an impact bearing puller is used to remove the bearing, then the inner race will be impacted hard like you stated. But what about a "press type" bearing puller was used where the inner race is being pulled out by a pressing mechanism and not by an impacting mechanism. In this case, would the bearing be still in good shape and re-usable?
Only if you could turn the puller with a short wrench. A good fitting press should keep the bearing parallel with the hub preventing shearing aluminum from that expensive hub.
F482SB-SL bearing size: 1pc #6802 and 1pc #15267
novatecwheels where can i get this bearing?
And the bearings in the freehub? How do i change those?
Hi. What torque setting do you recommend when tightening the axle?
Thanks
My favourite bike hubs for good reason.
what are the bearing sizes for the f482sb-sl hub
Lesson learned today. The hard way, ruined a couple of bearings with a rubber mallet :P
Where did you get the set of bearing press tools , they look very professional?
Good work,
What is the tool?
Jeff, we recommend to replace complete freehub, including seals.
at 6:00 you mention the wider side needs to go towards the bearings. In the video, he inserts the raised smaller diameter pice towards the bearing. Is that correct in the video?
Thanks for finding mistake in text in video. It should be written "...with smaller diameter..."
where did can find Novatec bearing installation tool kit sir ?
PLEASE SHOW US WHERE WE CAN BY THIS PERFECT BEARING PRESS TOOLKIT!!!!!
Please can you do a video on the Novatec Fs522sb hub
I just had to buy a replacement freehub body because its bearings were very rough, crunchy feeling, and the cassette cogs had dug into the splines. I bought the A2 ABG hub to prevent the damage from the cassette. However is it possible to replace the bearings in the freehub body itself in the future?
Perfekt instructions
Hello, I cant seem to remove the freehub body as you do @ 1:17.
I have followed all steps but cant get the freehub body off the axle, any advice?
Shawn Hennessy Hello, I am not sure why you cannot remove cassette body. Only reason I can think is that you have damaged drive system or it is stuck by mud. Try to push all axle from other side with cassette body out of hub shell.
i have f372sb, is the ring u removed at 0:13 compulsory? must i put it back?
Hey, what are the tools you are using and what is that lubricant? Thanks
Good afternoon.
Thank you very much for the video. I have a question for you - what is the difference between Novatec D041SB D042SB bushings and D481SBT D482TSBT?
Hello. That hubs have very different construction. D042SB has only industrial bearings, D482TSBT has industrial bearings and loose ball bearings.
@@novatecwheels Thanks a lot for your explanation.
I need a new hub set, which model can you recomend for 32H 9s MTB? compatible with aerospokes? thanks
Damn, have taken off both end caps as shown and onto pulling free hub body off but its stuck fast and won't move. Any tips?
It seems that your sprocket is bitten to freehub body. It happen usually if there is used Alloy freehub without ABG (Anti Bite Guard) and sprockets without spider.
@@novatecwheels thx for reply. turned out it was a seized bearing in freehub that had corroded a bit on to the axle meaning one couldn't pull off by hand. My fault due to lack of timely maintenance.
thank you!
What is the correct size bearings for this hub? I found out the hard way they do not handle (really) heavy rain very well and would like to replace my bearings.
Mark Huigen Yeah, kinda annoying to have to google around for so long... Wish novatec would put this info somewhere
Hi. Novatec D811SB and D812SB use 6902-2rs bearings?
What number of bearing is novatech used?
I wasn't able to remove the freehub, and I did remove the two end caps (and the NDS end cap in 3 parts) yet it's completely stuck, any help? Thanks!
send email for help with photos to info@novatecwheels.eu
· What is the tool you are using called?
Andrew, do you mean silver spacer? This silver spacer is needed to give back to the same position.
bonjour pouvez vous me dire ou je peux acheter l outillage merci
Hola! dónde venden ese kit de herramientas para rodamientos?
Hi, do you have instruction how to replace bearing for Novatec F362TSBT-11S hub? thanks a lot..
Like my hub
Good job! 🙂👍🏻
what is the name of your bearing press kit?
Hub Bearing Installation Tool Kit, you can visit www.eshop.novatecwheels.eu
If you can tell me where I can buy the set to install the bearings
Have you found that set? If yes please let me know where. Thank you:)
www.eshop.novatecwheels.eu/category/spare-parts/others/
What is the correct bearing size for the F742SB Hub?
6902 LLB
thanke you for video,
can you tell me the references of the bearings ?, thanks
THANKS!!!
Whats the name of the bearing toolset? Where do I buy it, please.
tising1 www.eshop.novatecwheels.eu/category/spare-parts/others/
Bonjour, merci pour votre vidéo! vous avez une vidéo pour remplacer les roulements sur Powerway R36 ? Merci
Salut tu as réussi à sortir le corps de roue libre ?
@@scorem77 Salut oui ça y est j'ai réussi ! merci
@@momodu6657 je viens de réussir il vient pas aussi facilement que sur la vidéo.
how about freehub bearing?
Great
Thanks, we are happy if our instruction can help :)
any link so you can buy?
www.eshop.novatecwheels.eu/eshop/tools/c-35.xhtml
Hi! My freehub is stuck on the hub body. Is there any way to solve this?
ditto. how did you solve it?
Don't worry, I just pushed the axle through using a threaded rod and socket
Boss good afternoon
Itong sa thru axle ng brusko sandugo mtb paano tanggalin
Sorry, I don't understand what you need.
how to replace bearings in novatec D042SB, please upload such tutorial. :D thanks
zainul arifin Hi, actual procedure is the same for D042SB hub. What is different is axle size and instead of allen key you will need 16mm wrench key. Cheers.
Mag replace sana Ako ng bearing sa left, kaya lang, di maalis yong lock
Did you follow instruction correctly?
Hi all,
bearing sizes you can find on this link:
issuu.com/novatecwheels/docs/novatec_hubs_guide_2014
Someone asks about the tools that you used to let you answer!
where do i buy.... hub tools....?i`ll like to hub tools ^^
Si Jeong www.eshop.novatecwheels.eu/category/spare-parts/others/
Qué torpe!
Pour la roue avant...
fuck that 11mm allen key...i coundn't find one at the local shop...only 10mm or 12...such a stupid idea Novatec...why didn't you made the hubs with 10mm or 12mm in mind ? Now i have to buy a 12mm key and carefully grind it so it could fit to that 11mm space.
you can get a 11 mm allen key on ebay. I bought 11,12,13,14,& 15mm from ebay
O
??? no voice? Too shy to talk?
For people is most important to understand instruction, right? Many people around the world do not speak English, therefor for them is text much easier to use.
What is the difference between the freehub model D042SB and D042SB-SA ?