Want to build something with a similar setup myself. Want to try and stay with a crank driven power adder just for tunability since I’m new to all this
Can you use the the dirty dingo low mount ac bracket setup with the mini ac which hugs the block pretty tight in a g body without having to notch anything
I have a Monte Carlo ss 88 I want this same set up , if I use a 2 inch cowl hood would that clear everything to close it so I don’t have to modify it or have to cut the hood to fit the magnuson in there ?
You are going to need bigger than 2 inch. The place were you run out of room is up front. The snout is way up there. A 2” would work if it wasn’t for that
I have a 1984 luxury Sport Monte Carlo with a 6.2 6l80e swap And Ford 9 inch rear. How much would you charge to install on my car? I am looking to have it done Beginning of spring
Oh look! (ANOTHER BORING LSX SWAP)...... WOOPITY DOO! Seems like a every day thing anymore. No "CREATIVITY" anymore.. Just buy a LSX and bolt this to it..
The trans brake and line lock is very unique
Yes sir please keep the videos coming 👍🏾
Super nice
Beautiful ❤
Very nice setup!
This is tge exact build i wanna do
It could Definitely be a sleeper minus the sweet whine of that supercharger.
I wanna see more videos on this car
Lucky for you we are doing a 10 rib conversion and throwing it back on the rollers
Want to build something with a similar setup myself. Want to try and stay with a crank driven power adder just for tunability since I’m new to all this
Forced induction is forced induction. They all have their downfalls. If you have questions feel free to ask!
Is this supercharger good for everyday use
Absolutely. It’s always there when you need it.
This is nice asf
Thank you!
How much do a nice engine setup start at? Labor install?
Roughly $21k installed
Can you use the the dirty dingo low mount ac bracket setup with the mini ac which hugs the block pretty tight in a g body without having to notch anything
I can’t confirm that it will or will not but I doubt it
What’s a good affordable set of headers that work great in a gbody 87 cutlass?
Have you weighed a G-body after an LS swap?
Can't say I have
Very cool car! Who builds your transmissions? Lol
What heat exchanger?
Nice clean swap. How much does a build like this cost?
If you are talking the entire swap.. like drop your car off, drive it home… 46k out the door
What ac compressor bracket are you using part number? Thank you
Holley 20-140
Hey homie, use that seatbelt! Shit happens quickly
Wanna take on another one
Ofcoarse!
I have a Monte Carlo ss 88 I want this same set up , if I use a 2 inch cowl hood would that clear everything to close it so I don’t have to modify it or have to cut the hood to fit the magnuson in there ?
You are going to need bigger than 2 inch. The place were you run out of room is up front. The snout is way up there. A 2” would work if it wasn’t for that
I have a 1984 luxury Sport Monte Carlo with a 6.2 6l80e swap And Ford 9 inch rear.
How much would you charge to install on my car? I am looking to have it done Beginning of spring
You typically have 10-11k in additional parts labor and tuning to complete a swap
@@Zero2SixtyPerformance I have a Monte Carlo that needs to pretty much be built up from the ground… how much do you think that’s be? Around 20k?
@@sixto7217 yessir
Where are you located
I got a el camino
I've got an El camino...
@@brianmathew09 thank you for the grammar correction. Lol
does magnason supercharger require dish or flat top pistons
The supercharger doesn’t care what pistons are in the engine but you would want a dished piston to lower the compression
What radiator do you recommend for the g bodys with higher horsepower and forced induction?
We use a lot of norther radiators. Look for something with large rows not the amount of rows.
Where and how do i order magnason fully put together ready to throw on engine
You are just looking for the head unit? What all are you looking for?
Yes unit
What's the rear gear ratio on the 9" and what's the torque converter setup?
3.73, FTI 3200
Will the factory hood be able to fit?
Not even close
How much for the coolant tank?
It was fabricated for this project. If I did it again probably $500.
Do you have to use cowl hood now
Yes
Would any pds supercharger clear stock hood or would you need to go centrifugal ?
408 compression? Heads?
If I recall it was around 10:1 and TFS heads
Where u get radio from ?
www.retromanufacturing.com/
I want to swap a 1974 cutlas to ls 6.0 any suggestions?
The 6l is a popular choice. Any 2500 silverado, yukon or escalade will do
Wat mufflers did U say they are?
Flowmaster FX
How much for an engine build like this
Just the engine or a complete swap? If you are talking about the entire swap, roughly $45k installed.
@@Zero2SixtyPerformance complete
Complete
What state are you working from
Florida
I have a couple for you to do for me bro.
Send'm down!
How much power did that set up make to the crank
We did not have put the engine on an engine dyno
Where are yall located
St. Petersburg, FL
@@Zero2SixtyPerformance cool I have a question do u yall have motors in stock or would I have my on motor .
We supply everything
@@Zero2SixtyPerformance wow ok do u have a number I can reach u at .
7273468919
I'm building a 6.0 now I would love to pick your brain
Give us a shout. 727-346-8919 or david@zerotosixtyperformance.com
Can you do a gbody swap for 6k everything included parts and labor
Not a chance. You will have 6k in just parts.
My brother built that car from scratch why are you taking all the credit.
Because your brother is not
Woop de do,another l s engine swap,boring
Oh look! (ANOTHER BORING LSX SWAP)......
WOOPITY DOO!
Seems like a every day thing anymore. No "CREATIVITY" anymore.. Just buy a LSX and bolt this to it..
Will that blower fit on an LS 2 or a LQ4
Yes with an adapter