Does the ball and socket really need to be clean and dry for proper sway control? What or how is the friction applied to the pivot? Rocky, thanks for the great video! Really appreciate the extra steps you took measuring the front as well as the two scale measurements. Jim
@@RVJimDAt 2:34 Rocky shows the plate below the ball and the bottom of the ball shank. The ball shank passes through a cone-shaped hole and within that cone is abrasive, ceramic material similar to that on brake shoes. The more pressure applied to the ball the more friction is applied to the ball shank preventing it from turning. Since the plate is attached to the bottom of the ball with a pin, and then to the chains attached to the trailer frame, sway control is applied. The bolts and plate Rocky points to can be removed and the abrasive cone replaced should it wear out. It’s a very good system and has served us well with our 1/2 ton truck and 7000 pound travel trailer.
Rocky your video was watched right before I was going to order a Weigh Safe WDH middleweight. Ordered the Anderson instead. Was on the fence but your video pushed me for the greaseless, lighter weight Anderson. Picking up the GD Imagine next Friday 👍🏻 thanks
First time watching how these hitches work.I work at Camping World and we sell lots of hitches,now I can be a better sales person because of knowing how they work.
@@RockyRohde We didn’t have a good experience with towing it would sway a lot worse with the wind. So I was told to turn off the sway control in the truck. Made a big difference. With it in it was causing to much friction.
This has to be the BEST ever tutorial and informative video yet! Excellent job!!! I am considering a Winnebago Micro Minnie and had been considering a Equalizer hitch.....not now! My 1st gen Tundra has a lower CCC and saving the weight will be a big help. The Anderson looks so much easier to handle. I have a cardiac issue and the Anderson is well within my ability to install and use. Thanks again, GREAT video!
Thanks! Glad my video helped.. The Andersen wdh is better technology without old school weight. I absolutely use mine and it is way better than heavy bars.. I used to just leave vehicle hooked up at rv parks because I didn’t care to mess with hitch.. now it’s a breeze to unhook..
I have the same setup. Ram 2500 and Andersen hitch. Also needed the 8" drop. Ram's sit high! :) Also, I found when installing the frame brackets it's best to have the trailer hooked up, but literally zero tension on the ball. Then put your chains on and screw the nut on the chains until there's about 1/2" showing. Pull the brackets so the chain is tight and tighten down the bracket bolts / set screw. At their recommended 29" or whatever there was way too much thread showing for their socket to be useful.
Great Quick Look at the install and principles of how this hitch works. No grease on the ball?? And don’t have to store the bars and have a lighter CLEAN shank & ball assembly?? I agree, this is a winner. Did you see that the bottom of the trailer-side plates moved forward after tensioning? Didn’t expect them to move, but that is where all the chain tension is focussed, I guess.
I have used mine for 3 plus years, works amazing. it is about 50 ish pounds altogether, very light weight compare to other brand. Never had sway issues down the road. Highly recommend this product...
I love that set up for the weight distribution, I have the old style heavy bars with a chain, that setup is very pricey but Lord it takes a lot of weight off the back of the truck and the tongue of the trailer.
excellent video.... ordered one. You should see if you can get an affiliate link. Also, I was told by Anderson that you can tighten the hitch more, but that the diameter of the red spring should not exceed the diameter of the washer.
It seems like this system would also help with bounce on uneven roads. My system continues to lift up to max upwards motion and lift increases all the way down. This seems like it provides max lift sooner and releases completely when it’s not needed. I may give it a try because my hitch was old when I installed it and I worry about fatigue
Purchased a new TT last year, and purchased the Anderson WDH. Love it for all the exact reasons you highlighted! No grease, lighter components to deal with, great anti-sway control, quiet operation, no need to disconnect anti-sway before backing up, etc. etc.
I had the RV dealer install mine. I was fishtailing above 55. I couldn't tell at the dealer, but the trailer was nose high upon arrival at home. 8K trailer with 800# tongue weight. F350 w/ 4K payload. Your ball is where I would expect it should be. They had mine set so the top of the ball was ABOVE the bumper foot step........................
Great video Rocky, enjoyed it. I had this hitch right after they came out and found your findings spot on. I’ve been on fifth wheels since and wanted to see if anything had changed. I agree the hooking, unhooking and carrying parts was the easiest. I would recommend you hook your chains from the front to the back, especially if the little springy retainer is gone or there’s not one. With the chains like you have them, in a turn, with slack in the chain, hit a bump, the hook jumps up and the weight of the chain pulls it off the truck. If you hook them from the front to the back and you slack off the chain and you hit a bump, the chains do not fall off. I see you got the little tin metal latch on it, but some people watching may be using the round S type with no safety catch.
The 4 turns is the starting point, I count the threads. I setup by counting 5 threads and depending on the weight after loading it, I can go to 6 threads if needed depending on the load
@John Daniel as little as possible, I don't like putting pressure on the urethane bushings while tightening the nut. I jack up the camper turn, then lower. I do that until I am done
The only thing that gets me is it seems you can't go too far positive in the angle of the truck to the trailer, like turning into a driveway with a bit of an incline. Wouldn't that force a lot of weight off the drive axle, onto the hitch chains and thus the tongue, where the traditional spring bars would have some flex in the bars? I don't see where this has that much 'give' in the tension system.
In the video (8:10) you put up a message about torque numbers (75-90 ft-lbs) for the brackets on the trailer and it says depending on trailer frame. What is the determining factor(s) listed in the manual regarding the frame for the correct torque? Thanks.
How do you know when the trailer and truck weight are floating?? This is such a helpful video ....trying to understand what you are seeing that allows you to know that. Thank you!
You can tell when you have both hands on the steering wheel white knuckled. It just does not feel stable. This happens when you have to much tension and rear wheels do not have enough weight.
@@RockyRohde When you are first coupling the truck to the trailer and you lower the trailer onto the hitch just until it couples...you then say the truck and TT should be 'floating' meaning almost no weight on either. You are sitting next to the jack. What are you seeing that allows you to know they are 'floating' at that point?? I'm having trouble judging when I have coupled then lift the truck up with the jack just how far is 'floating'. Thanks for your patients with this question. Absolute newbie.
At the start of your video, you mentioned that a conventional WDH with spring bars puts a lot of force thru the trailer A-frame rail. This is correct. Trailer frames are designed with those loads in mind. Those forces can be fairly high, yes, but they're being applied vertically thru the ball and the frame rail. The leverage point is usually about two feet away from the ball on the frame rail. In my opinion, the Achilles heel of the Anderson is that it changes the direction of the loads used to lever the weight of the tongue. The chains pull the trailer up tight against the coupler latch. As a result, the lever arm is much shorter, specifically, the height from the chain plate to the ball, which is only about a foot. To generate the same moment around the ball as a conventional spring bars requires double the force (or more). All of that force is now being pulled against the latch assembly of the coupler. I have yet to see any details from the coupler (or frame) manufacturers related to sustained loads in that direction. Also, this often results in the frame brackets slipping against the frame if people don't use the screws to secure the frame brackets, which reduces the weight transfer. Finally, from your scale tickets, we can see that the hitch restored 200lbs to the front axle. However, without a unloaded truck weight (i.e. without the trailer) we can't see how much weight was levered-off the front axle to start with. While the fender heights are a decent indicator of front axle load restoration, they're not as accurate as a scale weight, especially in trucks with heavy duty front suspensions (like my super duty with the plow prep package). While I've never personally owned one, the early discussions around this hitch when it first came out indicated that it struggled to be able to transfer much more than about 200lbs back to the front axle. On heavier trailers north of 800lb tongue weight, most trucks didn't seem to be able to get back to the original front axle load with the Anderson hitch. Not trying to put down the product, just trying to share another viewpoint. For many trailers, it's quite capable, and I certainly understand the advantages over a conventional design. Giving credit where credit is due, it's a unique design and I like the concept, I just don't feel that the pros outweigh the cons.
I've used the Andersen for years... The Andersen has some of the best sway control available. I did it the way you did it for the first 2 years, then realized that if you reverse jack up the rear end of the truck using the pin jack of the trailer PRIOR to tightening up the chains you have better weight distribution. I've found this is the step that many people miss. It made quite a difference towing for us, far better bounce (porpoising) protection, and even better sway control than before.
What does reverse jack up mean? Do you mean to attach the coupler to the hitch and then raise both the truck and the trailer together, and then tighten the chains, and then retract your jack so that the full weight of the trailer is on the tongue with the hitch engaged?
@@JDDJR7 yes, exactly. I have used the Anderson on a number of different applications and the second I did it that way it made a massive difference. But prior to doing this you need to permanently affix and Or weld or screw the chain mounting points to your frame. Once you do that it will not slip at all. Doing it that way also provides greater weight distribution to the front
@@rjhein Exactly the way I do it too, it just made sense. My new to me toy hauler came with the Anderson hitch and I just did it that way not knowing any better : ). It works great still after about a thousand miles with it.
Yup, I pull the truck up pretty high with the trailer jack, THEN attach the triangle plate and tighten the chains so 8 threads are showing, and THEN lower the whole thing down so the truck is taking all the weight. The result is no sway, no bounce, no porpoising. And that's with my 2014 Tundra Crewmax that has a terrible payload rating. Love the Andersen hitch!!
Has anybody found that this weight distribution hitch stretches the receiver cup at the beginning of the trailer so that it becomes a elliptical and has trouble accepting the ball
Nice mega cab. I run Anderson no sway as well. Haven't run anything else, so couldn't give you a comparison. I do get a pushed around a bit, but the sway control bushing seems to keep things from getting out of control 🤷
Rocky (or anyone), how do you deal with porpoising and bouncing? GMC, Ford, Chevy, or Ram...which truck handles the best for bumper pulling? My GMC 2500 towing GD Imagine using Andersen bounces all over the place...not sure if it's the hitch, the truck or the trailer. Comments appreciated.
My gm bounced a lot with my fifth wheel also.. I would try some stiffer shocks.. My Ford did not have any bounce.. both trucks are leaf spring rear axle so it more than likely has to be shocks.. I have had all three late models and the Ford is the best for me towing.. Shocks should be an easy fix for you.. Yours might be bad.. Remove the bottom bolt and see how much resistance it has..
Great video. We have been using this for 4 years behind our Renegade 38 ft Super C. Love it. BTW You were almost 100% road ready. But you did not have the hitch pinned. Thank you for the video. This is the only hitch I will use.
He didn’t say grease the anti-sway … he recommended greasing the spring bars that do the weight distribution. Anti-sway is performed by a different bar.
great video.. I'm new to towing a camper, always owned a motorhome towing a Jeep. So, I'm researching both trucks & camper trailers. For a camper, I was focused on a Terra Oasis (7,500 gross weight), but after researching the Lance 2075 (5,900 gross weight) and watching all of your wonderful videos, I am thinking this may be a better route. I see you what looks like you tow with a 1/2 ton Titan with max towing about 9K lbs and max payload about 1,600 lbs. How is that working out for you when you are in high winds, semis passing on the interstate, or climbing 10K' peaks? Do you ever wish you had a larger truck? Thanks!!
How is backing with the Andersen; can you back with the chains connected, etc? Haven't seen any good vids showing that procedure. Am comsidering an Anderson for a 26', 7590 GVWR trailer. Y'all Be Safe!
2 questions. Can you put your tailgate down? And have you taken off the supports on your trailer frame to see if those anchoring bolts have damaged your frame? I'm currently running a 2021 GMC Denali HD with a 2020 Jayco 280RSOK trailer and the combined weight is 19,200. I am using a 14k Equal-I-zer hitch and I've got an 18" shank on it to allow me to take my tailgate down. The problem I'm having is that the hitch weighs a ton and I'm not a spring chicken anymore.
Excellent job on producing your video. I like the simplicity of the Andersen hitch. Have you notice any wear of the chain links? I'm thinking of ordering one of these. I hate messing with the grease a and the weight of my E2.
I have a TT which is about 1K lighter than yours. I have used an Andersen with a 2500 Ram for 3 seasons and thousands of Rocky mountain miles. Works well with a proper truck like yours.
@@safrench I agree with pulling anything over 26 feet with a 3/4 ton. But, not the 6500 trailer weight. Many half ton trucks are rated for 10, 000 pounds or more. The weight of the trailer will not be the limiting factor for a 1/2 ton. Pay load will be exceeded long before you reach the max tow rating.
@@bobdrawbaugh4207 I will be installing my Andersen hitch on my TT and pulling it with my F-150. My TT is 26' box length and 6,800 lb gvwr with 800-900lb tongue weight (using my Sherline tongue scale). My truck is also my daily driver when I'm not traveling with the TT and I didn't want to have to drive a 3/4 truck (or pay for it) for the majority of the miles that it would be driven. I ordered my Supercab F-150 with the tow package and 18" wheels for towing. The very first thing I did when I got to the dealership to check out my truck was open the drivers door and check the sticker. This half ton truck has a payload of 2,175lbs and I will have a comfortable amount of payload remaining even if I load out the TT to its max. The truck has a tow capacity of 9,400 since it's a 4X4 and I didn't get the 373 gears. I know I'll probably have to listen to know-it-all's in my travels tell me that my truck is too light but I'll just open the door and point, then wish them a pleasant day.
I just installed one of these last week for a new trailer using your video and the one from Andersen. I noticed some issues with your install and wondered if you went back to correct them and if you noticed any difference. First issue was with the triangle plate. I see you insert the pin and then swivel it into position with your hands. If that plate can swivel that easily you have no sway control. Mine was similar, but followed the directions of using a piece of wood and mallet to knock the plate inline with the bumper. Did you ever fix that? What did you have to do? Next noticed your installation of the trailer brackets were not done according to directions. Sounded like you measured the brackets at 29” instead of using the chain lengths. Mine came out at 28” at the top and 27.25” on the bottom. Which is another part of the install that differed. You installed the brackets straight up and down with the chains pointing to the ground. The installation calls for pulling the top back as far as possible and the chain on the bottom as parallel possible. Essential at an angle with the top further from the coupler. Did you ever go back and reinstall the brackets?
according to those cat scale tickets , both times the rear axle outweighed the front axle by a few hundred pounds give or take...shouldnt the axles be the same or as close to the same ratio as trhey were when you weighed your truck alone? as it sits the front axle is still lighter than the rear so despite the heights of the wheel wellos being close to original im betting that front axle is still at least 300 pounds lighter than the rear making it imho iffy when it comes to stopping
No it’s not supposed to balance.. just shift a percentage of weight to front axle. Your payload rating is designed for the rear axle for the most part.
It’s not a ratio so much as putting the pounds back on the front axle. If your front end is 1 200lbs lighter you want to get as close to that as possible back on the front axle.
Great video. Do you get any sway when you are passed by a big tractor-trailer? I currently use a Blue ox sway pro with a 30 ft trailer and a half ton F-150. Crosswinds usually don't affect it at all but when I am passed by a tractor-trailer it sways a lot. Sometimes I feel like I'm being sucked into the tractor-trailer's lane and then pushed off the road after it gets by me.
The sway is less than I had with bar hitch.. one thing to remember when passing trucks is have a little pull on trailer and going down hill. When trailer is pushing the truck it will sway with winds. I always make sure I’m accelerating slightly when trucks are beside me or when going downhill.. A lot of peeps will let off accelerator when trucks go around as it’s the natural feeling. Keep a little pull on it and it will help significantly with your current hitch also
Wasn’t the 4-turn tightening of the nut supposed to be done with the camper/trailer already sitting on the hitchball? I was basing this observation from the official Anderson Hitches video. Im getting one tomorrow and wanted to make sure I do it right or not put too much tension on the chains. Great video by the way!
Are you still using the anderson hitch and liking it? I have a stryker 2912 and using husky now. Looking to have less bounce after crossing bridges and such. Thank you
I have a Ram 3500 Limited I think you have a 2500 and coil springs. does yours have air ride? I have a 22ft enclosed trailer that I use for tool trailer I am a mobile Heavy equipment mechanic. Just bought haven't received yet same WD. I have 1400lbs of tongue weight. and live in Florida make multiple trips to our place in NC, trailer pulls ok but feels funny sometimes ,hoping that this make a difference, being a heavy truck with air ride will only drop a 1" but I get weird messages and warnings say air ride will not function properly, cannot adjust, but it's already up, when I first pulled I didn't have a tongue scale now I do, but Cat scaled it and had 1600lbs. Top of ball was actually worn. I had a big 72" Snap On tool box across the front full, was just to much weight..Box weighs 1200lbs empty. Anyway swapped it out to a Harbor freight 42" and removed a lot of my tools. The trailer was custom built "V" slant nose,12"OC floor cross members and 7000lb torsion spread axles, and a 7000lb ramp door, with 7'6" height. so wondering if this will help any on a HD truck? I see you have a big truck I race here a mega truck or Hill in Hole Jeep for a few years. hence my name Joker Jeep.
Rocky, you still using this? how is it holding up, 1 yr later? I have an e2 WDH setup from FastWay. But it is super heavy. I tow with an Audi Q7, and any unnecessary weight I can shed would be awesome. Very well done explanation and walkthrough on the install and setup. Thanks for this. Subbed!
I adjusted to my chain length.. here is installation procedure download2271.mediafire.com/tf1c7iiuv9kg/bx5xm3p7hie6515/3932+-+WD+Hitch+installation+manual+2022-Low+Res.pdf
@@laker42 you won’t regret it.. My Toy hauler is 36’ and I load my lifted canam max XMR in the back…. It weighs 2700 pounds. Pulls like nothing is behind me.. plus no more popping and creaking..
I am using the Equlizer 4 hitch on our Ram 2500 and Flagstaff RV. It weighs 7600 unloaded with a hitch weight of 963. The camper is 35' .The Eq does ok, but the weight and grease is getting to me. Is the Anderson a real upgrade rom my Eq 4?
How did you loosen the chains at the scale? With the big socket? If so, HOW do you know how much to tighten it again, unless you start over and count 4 revolutions I don't see how you'll know. And is 4 revolutions AFTER hand tightening or..? Sorry, I'm a girl. 😅
It's not always so easy to get that triangle plate off even raising the jack pad up to loosen tension, once I have it all setup, I measured the distance from the washer behind the nut to tip or end of the thread, I used an old credit card or any plastic card because it's easy to cut . and cut the card in an L shape and made it into a depth gauge, so whenever I need to loosen a few threads to get the plate off, I just re tighten it and use the cutout credit card to make sure it's the right length. This works on both sides
Great video. I have this hitch and I have struggled so much with figuring it out because I also have the air suspension. Quick question: when you do all your measuring and setup, do you have to turn the suspension off and put it in tire jack mode?
Here is how I setup my tension. I hook it up to trailer and let air suspension adjust. Then I raise it with the jack about 2-3 inches and snug chains by hand. Then I drop the weight back on vehicle. You will notice chains are tight and should be good to go!!
So technically.. was your drive axel overloaded without that hitch engaged? I have a 19 ram 2500.. my axel rating is 6000lbs. I'm assuming yours is similar?
Thank you for the time you put in this review. We are first time Travel Trailer owners( still on order) in our 70’s. Towing was one of the biggest stressors that had talked us out of the RV life for the last 4 years. We finally said, WTH, we’ll never know unless we try. You took a lot of the anxiety out of this process with this video. The weight aspect had a big factor with us choosing this hitch. After a few months, anything new to add? Thanks again. Larry
Well I do have a question. Sort of confused me. You said you measured to the height of the coupler and got 10.” And the ball needs to be 1 1/2” taller. That’s where I’m lost. For everything to be level it would seem that the top of the ball should be the same as the top of the coupler? Thank you.
You want the trailer to sit almost level with truck. Most trucks will drop 1” to 1.5” with weight. For initial setup for ball height hook it to truck and adjust it up or down to find the closest to level. Once you have that add the chains and tension.
@@larrymccorkle3409 he threw me off with that too, but he meant 1ft 10in. He repeated it when he measured the truck side and said '1ft...10.." that when I caught on to his measurements. Great video!
How have you liked your Stryker trailer? Quality good? Would you buy it again? Do you have any issues with the width of your Can Am when loading it into you trailer? Do you drive it straight in or do you back it in?
I am currently at Disney ft wilderness in Florida. Trailer pulls great and I really like that it has shocks on the axles. Just traveled 1200 miles and carried golf cart with us. Quality in build is good for me.. I have had a 44 voltage fifth wheel and it is about the same. Stryker offers a really good toy hauler with larger tanks and good floor plans. I like a 16ft garage, large King bed with room to walk around it, and a large bathroom.. I also like that I don’t have to stop at truck stops to get fuel. I have been camping for over 20 years and not interested in any other trailer. If you have a dealer close go check one out. Sure if I didn’t want a toy hauler I would prob have something else.. this one just checks all the boxes for me. My canam defender XMR max 6 passenger fits with 30” boggers on 15x7 wheels. It fits forward and backwards. Keep offset close.
Rocky : Well presented. I'm in the same boat as yourself : Getting a new trailer & tired of lifting the heavy old hitch & bars. My only concern is most of the youtube's the people had pretty light or small trailers. Mine is about 8500#'s wet. Now that you have had yours for a time, has your opinion changed? does it take the sway out any different than old set up? You showed the 4 turns on the 'port' side; did you do the same on the 'starboard' side as well and just not record it?
Just pulled my trailer from Texas to Florida. It was 1092 miles each way with golf cart in trailer. Pulled like a dream. I absolutely recommend as it is so easy to hookup. The sway control is as good as other hitches. When I hook the trailer up I latch it and lift truck about 4-5” from being able to latch hitch. Then I hand tighten each side to remove slack and I let trailer down. The chains are extremely tight and pulls well for me. I don’t really use the socket and wrench. I let the jacket do the work same as a bar hitch. The hitch is very quiet and I love the fact I can remove it without killing my back. My days are done with bar hitches. You will have zero regret with the Andersen. Most that have anything bad to say about it don’t own it…
2 questions: with th 8" drop you are all set for a truck with a lift kit? also how do you know what size bracket do you need...that sheet shows different bracket size for the 10k gtwr...please help.
I ordered the 2.5 shank from Andersen. 8” should be good for a leveled to 3.5” lift truck with 35” tires. If you are stock with no level kit prob need a 5”.. I ordered the larger drop and if it was to much I could just cut it off..
Depends what your looking for.. my voltage 4250 fifth does not have a 16 ft garage.. does not fit under a lot of trees, and requires truck stops.. My defender Max 6 passenger XMR lifted with 30’s fits in the Stryker.. it also has shocks on the axles.. been camping 20 years really like this over the fifth.. easier to hookup and pull.. it’s all about what you want
100 yrd tape? Man a 48 inch measuring stick would have made things much easier and way more accurate. I had an Equalizer hitch and greasing the bars were not in the instructions. I think that's where the friction helps to reduce sway. With that said, I do appreciate the video. You definitely demonstrated just how light the Anderson hitch really is.
Hey, Rocky what kind of mechanic are you? My son is interested in becoming a mechanic or something similar but I don't know anything about tradework so I have a hard time helping him decide what to do
I started in the oilfield when I was 16 worked on mud pumps, Diesel engines, and Rig electric and instrumentation. In my early 20’s I decided to get into compression and natural gas engines.. Big accesable engines that were clean instead of knuckle busting compartment engines. Worked mostly on cat engines on compressors 3606, 3608, 3516, 33 series engines. If he is interested in cleaner engine work and good pay check out compression.
I don't see how the sway control works. With the equalizer you used to have the friction makes since. With this I just don't see it. Also how does it do backing up on sharp, almost jack knifed, angles? Seems like it'll split those bushings?
I can see how the sway part works what I can get my mind wrapped around is how the WD works without stiff bars pulling up cant see how chains can do the same as a stiff bar
The hitch ball stem is press fit into a urethane cone, the more weight on the ball the tighter it holds. The fin at the bottom is connected to the ball stem and the chains pull against that tension.
The tension on the urethane bushings never changes once you set it by the number of turns on the nuts. This hitch handles turns when backing up very well. The pivot happens in the tapered ball stem turning inside the alloy housing, which is seated into a polymer friction sleeve. It is that friction which controls any tendency to sway. As the above post states, the more weight on the ball, the more friction there is, with a corresponding increase in sway resistance. The weight transfer is handled by the chain tension pulling on the yoke on the bottom of the ball stem.
I had a 2019 Tundra 1794 and a Lance 2465. Total Rig 13970 lbs Trailer only 6468 Truck only 6600 Tongue Wt 902 The payload is 1185 lbs. As you can see a max trailer weight of 9100lbs means nothing, as a tongue weight of 902 from payload of 1185 leaves nothing for people and supplies in the truck. I tried towing, but it wasn’t very good. I switched to a 2022 F350 with a 3700 lbs payload and max trailer of 15000 lbs. So, everything well within capacity. However, I could not get the trailer to stop swaying. Anything more than 60 mph, bad sway. Going downhill even worse. I tried everything with the Andersen hitch, adjusted height, chain tensions, reload weight, etc. It just would not stop swaying at more than 60 mph or downhills greater than 50 mph. I switched to a trunion bar hitch (Weighsafe) and have zero sway. Im extremely disappointed in Andersen hitch and would ver recommend it in a trailer more than 2000-3000 lbs.
Thank you for reviewing and explaining how to use our hitches! We try our best to make them the best out there!
Thanks for making a great product!!
Does the ball and socket really need to be clean and dry for proper sway control? What or how is the friction applied to the pivot? Rocky, thanks for the great video! Really appreciate the extra steps you took measuring the front as well as the two scale measurements. Jim
@@RVJimDAt 2:34 Rocky shows the plate below the ball and the bottom of the ball shank. The ball shank passes through a cone-shaped hole and within that cone is abrasive, ceramic material similar to that on brake shoes. The more pressure applied to the ball the more friction is applied to the ball shank preventing it from turning. Since the plate is attached to the bottom of the ball with a pin, and then to the chains attached to the trailer frame, sway control is applied. The bolts and plate Rocky points to can be removed and the abrasive cone replaced should it wear out. It’s a very good system and has served us well with our 1/2 ton truck and 7000 pound travel trailer.
Rocky your video was watched right before I was going to order a Weigh Safe WDH middleweight. Ordered the Anderson instead. Was on the fence but your video pushed me for the greaseless, lighter weight Anderson. Picking up the GD Imagine next Friday 👍🏻 thanks
You made everything simple. Thank you for your presentation and the cat scale. You really sold Anderson pretty well.
Thanks!
First time watching how these hitches work.I work at Camping World and we sell lots of hitches,now I can be a better sales person because of knowing how they work.
Thanks!! They definitely make a more stabil pull..
@@RockyRohde We didn’t have a good experience with towing it would sway a lot worse with the wind. So I was told to turn off the sway control in the truck. Made a big difference. With it in it was causing to much friction.
This has to be the BEST ever tutorial and informative video yet! Excellent job!!! I am considering a Winnebago Micro Minnie and had been considering a Equalizer hitch.....not now! My 1st gen Tundra has a lower CCC and saving the weight will be a big help. The Anderson looks so much easier to handle. I have a cardiac issue and the Anderson is well within my ability to install and use.
Thanks again, GREAT video!
Thanks! Glad my video helped.. The Andersen wdh is better technology without old school weight. I absolutely use mine and it is way better than heavy bars.. I used to just leave vehicle hooked up at rv parks because I didn’t care to mess with hitch.. now it’s a breeze to unhook..
I have the same setup. Ram 2500 and Andersen hitch. Also needed the 8" drop. Ram's sit high! :) Also, I found when installing the frame brackets it's best to have the trailer hooked up, but literally zero tension on the ball. Then put your chains on and screw the nut on the chains until there's about 1/2" showing. Pull the brackets so the chain is tight and tighten down the bracket bolts / set screw. At their recommended 29" or whatever there was way too much thread showing for their socket to be useful.
Great Quick Look at the install and principles of how this hitch works. No grease on the ball?? And don’t have to store the bars and have a lighter CLEAN shank & ball assembly?? I agree, this is a winner.
Did you see that the bottom of the trailer-side plates moved forward after tensioning? Didn’t expect them to move, but that is where all the chain tension is focussed, I guess.
Thanks for showing the Cat scale results, it demonstrates that it's doing what it is designed to do.
Thanks for watching!
Thanks!
Thanks!!
I have used mine for 3 plus years, works amazing. it is about 50 ish pounds altogether, very light weight compare to other brand. Never had sway issues down the road. Highly recommend this product...
Have used mine for 2 yrs. now and it does a great job and is great on the hook and unhook.
I love that set up for the weight distribution, I have the old style heavy bars with a chain, that setup is very pricey but Lord it takes a lot of weight off the back of the truck and the tongue of the trailer.
excellent video.... ordered one. You should see if you can get an affiliate link. Also, I was told by Anderson that you can tighten the hitch more, but that the diameter of the red spring should not exceed the diameter of the washer.
You won’t be disappointed.. The adjustability and lightweight hitch is amazing..
Looking at buying my first WDH and sincerely appreciate your thorough review. Thank you!
Thanks.. still highly recommend this hitch!
It seems like this system would also help with bounce on uneven roads. My system continues to lift up to max upwards motion and lift increases all the way down. This seems like it provides max lift sooner and releases completely when it’s not needed. I may give it a try because my hitch was old when I installed it and I worry about fatigue
Purchased a new TT last year, and purchased the Anderson WDH. Love it for all the exact reasons you highlighted! No grease, lighter components to deal with, great anti-sway control, quiet operation, no need to disconnect anti-sway before backing up, etc. etc.
I had the RV dealer install mine. I was fishtailing above 55. I couldn't tell at the dealer, but the trailer was nose high upon arrival at home. 8K trailer with 800# tongue weight. F350 w/ 4K payload. Your ball is where I would expect it should be. They had mine set so the top of the ball was ABOVE the bumper foot step........................
Good clear information ... and with the one item so many miss ... the unhitching process
Great video Rocky, enjoyed it. I had this hitch right after they came out and found your findings spot on. I’ve been on fifth wheels since and wanted to see if anything had changed. I agree the hooking, unhooking and carrying parts was the easiest. I would recommend you hook your chains from the front to the back, especially if the little springy retainer is gone or there’s not one. With the chains like you have them, in a turn, with slack in the chain, hit a bump, the hook jumps up and the weight of the chain pulls it off the truck. If you hook them from the front to the back and you slack off the chain and you hit a bump, the chains do not fall off. I see you got the little tin metal latch on it, but some people watching may be using the round S type with no safety catch.
The 4 turns is the starting point, I count the threads.
I setup by counting 5 threads and depending on the weight after loading it, I can go to 6 threads if needed depending on the load
5 threads works for us also pulling a #4000 trailer and #450 tongue weight.
How much tongue weight do you need on truck while adjusting?
@John Daniel as little as possible, I don't like putting pressure on the urethane bushings while tightening the nut.
I jack up the camper turn, then lower. I do that until I am done
That is what I do.. Set them 1/2 turn at a time
Great video! I’m new to trailer towing and the bar systems looked like a royal pain in the backside. The chains for the win!
Great video! My sales woman had me get it because I travel alone. Great not having the heavy bars. Thanks!
Great video. I'm going to get one tomorrow. The Cat scale results were great.
Great video! I learned a ton!!! Thank you so much!!!
Just got one, ready to try it out. Tired picking up those heavy bars...
Is no one going to mention the classic original looking Bigfoot 1 in the background???
Awesome video… very efficient with no bs. Appreciate it.
Thanks!
13:15 Two things.
1. I've seen in other reviews that the socket is already marked with a solid line?
2. Your coupler is still open! 😲
The only thing that gets me is it seems you can't go too far positive in the angle of the truck to the trailer, like turning into a driveway with a bit of an incline. Wouldn't that force a lot of weight off the drive axle, onto the hitch chains and thus the tongue, where the traditional spring bars would have some flex in the bars? I don't see where this has that much 'give' in the tension system.
In the video (8:10) you put up a message about torque numbers (75-90 ft-lbs) for the brackets on the trailer and it says depending on trailer frame. What is the determining factor(s) listed in the manual regarding the frame for the correct torque? Thanks.
How do you know when the trailer and truck weight are floating?? This is such a helpful video ....trying to understand what you are seeing that allows you to know that. Thank you!
You can tell when you have both hands on the steering wheel white knuckled. It just does not feel stable. This happens when you have to much tension and rear wheels do not have enough weight.
@@RockyRohde When you are first coupling the truck to the trailer and you lower the trailer onto the hitch just until it couples...you then say the truck and TT should be 'floating' meaning almost no weight on either. You are sitting next to the jack. What are you seeing that allows you to know they are 'floating' at that point?? I'm having trouble judging when I have coupled then lift the truck up with the jack just how far is 'floating'. Thanks for your patients with this question. Absolute newbie.
This is an excellent video. Great job, and thank you for posting.
Glad you enjoyed it!
I see you have an Escort radar detector. You can use a blend mount and mount it to the mirror to free up windshield space.
At the start of your video, you mentioned that a conventional WDH with spring bars puts a lot of force thru the trailer A-frame rail. This is correct. Trailer frames are designed with those loads in mind. Those forces can be fairly high, yes, but they're being applied vertically thru the ball and the frame rail. The leverage point is usually about two feet away from the ball on the frame rail.
In my opinion, the Achilles heel of the Anderson is that it changes the direction of the loads used to lever the weight of the tongue. The chains pull the trailer up tight against the coupler latch. As a result, the lever arm is much shorter, specifically, the height from the chain plate to the ball, which is only about a foot. To generate the same moment around the ball as a conventional spring bars requires double the force (or more). All of that force is now being pulled against the latch assembly of the coupler. I have yet to see any details from the coupler (or frame) manufacturers related to sustained loads in that direction. Also, this often results in the frame brackets slipping against the frame if people don't use the screws to secure the frame brackets, which reduces the weight transfer.
Finally, from your scale tickets, we can see that the hitch restored 200lbs to the front axle. However, without a unloaded truck weight (i.e. without the trailer) we can't see how much weight was levered-off the front axle to start with. While the fender heights are a decent indicator of front axle load restoration, they're not as accurate as a scale weight, especially in trucks with heavy duty front suspensions (like my super duty with the plow prep package).
While I've never personally owned one, the early discussions around this hitch when it first came out indicated that it struggled to be able to transfer much more than about 200lbs back to the front axle. On heavier trailers north of 800lb tongue weight, most trucks didn't seem to be able to get back to the original front axle load with the Anderson hitch.
Not trying to put down the product, just trying to share another viewpoint. For many trailers, it's quite capable, and I certainly understand the advantages over a conventional design. Giving credit where credit is due, it's a unique design and I like the concept, I just don't feel that the pros outweigh the cons.
Great video. Lots of information throughout
Glad it was helpful!
Thanks for this review. It helped us decide 👍🏻
Glad I could help!
Did you really put grease on the friction part of the bars? Isn't that just getting rid of your sway control or drastically reducing it?
Are there any discount codes available now? I need to purchase one soon.
what size bolt you need for the chain tightening
I've used the Andersen for years... The Andersen has some of the best sway control available. I did it the way you did it for the first 2 years, then realized that if you reverse jack up the rear end of the truck using the pin jack of the trailer PRIOR to tightening up the chains you have better weight distribution. I've found this is the step that many people miss. It made quite a difference towing for us, far better bounce (porpoising) protection, and even better sway control than before.
What does reverse jack up mean? Do you mean to attach the coupler to the hitch and then raise both the truck and the trailer together, and then tighten the chains, and then retract your jack so that the full weight of the trailer is on the tongue with the hitch engaged?
@@JDDJR7 yes, exactly. I have used the Anderson on a number of different applications and the second I did it that way it made a massive difference. But prior to doing this you need to permanently affix and Or weld or screw the chain mounting points to your frame. Once you do that it will not slip at all. Doing it that way also provides greater weight distribution to the front
@@rjhein Exactly the way I do it too, it just made sense. My new to me toy hauler came with the Anderson hitch and I just did it that way not knowing any better : ). It works great still after about a thousand miles with it.
Yup, I pull the truck up pretty high with the trailer jack, THEN attach the triangle plate and tighten the chains so 8 threads are showing, and THEN lower the whole thing down so the truck is taking all the weight. The result is no sway, no bounce, no porpoising. And that's with my 2014 Tundra Crewmax that has a terrible payload rating. Love the Andersen hitch!!
Great video. Covered a lot of pertinent information..
Thanks.. Andersen knocked it out of the park with this hitch..
Buy yourself a 25' tape....................
Yeah I know…… had 4 2 weeks ago… when you need them good luck lol
@@RockyRohde Got kids?
Why?
Can you back into your site without undoing the chains or do you have to loosen them first?
Yes you don’t have to loosen them
Has anybody found that this weight distribution hitch stretches the receiver cup at the beginning of the trailer so that it becomes a elliptical and has trouble accepting the ball
How has this hitch worked out for you over the past year?
why doesn't anybody show the length of the trailer when hooked up ? good video tho:)
32 foot total length
Nice mega cab. I run Anderson no sway as well. Haven't run anything else, so couldn't give you a comparison. I do get a pushed around a bit, but the sway control bushing seems to keep things from getting out of control 🤷
I ran the others with same result.. Andersen has my vote hands down lol
@@RockyRohde good to know that if I switched it would probably be similar, unless I went with pro pride, just not ready to drop $3k+ on a hitch
Rocky (or anyone), how do you deal with porpoising and bouncing? GMC, Ford, Chevy, or Ram...which truck handles the best for bumper pulling? My GMC 2500 towing GD Imagine using Andersen bounces all over the place...not sure if it's the hitch, the truck or the trailer. Comments appreciated.
My gm bounced a lot with my fifth wheel also.. I would try some stiffer shocks.. My Ford did not have any bounce.. both trucks are leaf spring rear axle so it more than likely has to be shocks.. I have had all three late models and the Ford is the best for me towing.. Shocks should be an easy fix for you.. Yours might be bad.. Remove the bottom bolt and see how much resistance it has..
Check into Timbrens also.. Takes about 15 minutes to install.. search etrailer timbren rear suspension enhancement 2020 GMC sierra
This is the direct video.. Watch how it helps Gm Suspension towing
ua-cam.com/video/gLxA-J99U8k/v-deo.html&feature=shareb
Great video.
We have been using this for 4 years behind our Renegade 38 ft Super C.
Love it.
BTW
You were almost 100% road ready.
But you did not have the hitch pinned.
Thank you for the video.
This is the only hitch I will use.
Thanks!
You don't grease anti sway! If you grease the bars you lose the anti say properties. The creaking is normal.
He didn’t say grease the anti-sway … he recommended greasing the spring bars that do the weight distribution. Anti-sway is performed by a different bar.
Thanks for making the video
I Appreciate that!
great video.. I'm new to towing a camper, always owned a motorhome towing a Jeep. So, I'm researching both trucks & camper trailers. For a camper, I was focused on a Terra Oasis (7,500 gross weight), but after researching the Lance 2075 (5,900 gross weight) and watching all of your wonderful videos, I am thinking this may be a better route. I see you what looks like you tow with a 1/2 ton Titan with max towing about 9K lbs and max payload about 1,600 lbs. How is that working out for you when you are in high winds, semis passing on the interstate, or climbing 10K' peaks? Do you ever wish you had a larger truck? Thanks!!
Get a 250 or 350 if you plan to do much towing. They tow with ease. A 1/2 will tow some but it requires a little more stress..
How is backing with the Andersen; can you back with the chains connected, etc? Haven't seen any good vids showing that procedure. Am comsidering an Anderson for a 26', 7590 GVWR trailer.
Y'all Be Safe!
Are you still using the hitch? If so how has your experience been?
Thanks!
I moved up to a large toy hauler 5th wheel.. I still recommend this hitch 100% for tongue pull trailers
i'm going to look for a how it works video. I just don't understand exactly what it does
Chains keep tension the same way bars do. Anti sway is a Teflon sleeve inside hitch that keeps tension for sway.
@@RockyRohde ahhh I think i understand. i'm new to RVing. gonna be out there in a few years
2 questions. Can you put your tailgate down? And have you taken off the supports on your trailer frame to see if those anchoring bolts have damaged your frame? I'm currently running a 2021 GMC Denali HD with a 2020 Jayco 280RSOK trailer and the combined weight is 19,200. I am using a 14k Equal-I-zer hitch and I've got an 18" shank on it to allow me to take my tailgate down. The problem I'm having is that the hitch weighs a ton and I'm not a spring chicken anymore.
Yes and yes to your question. The Andersen hitch is lightweight and very easy to install. I have no marks on trailer frame from brackets.
Still recommend this hitch? Am going from a fifth wheel back to a TT and want something quiet.
Yes I still recommend
Excellent job on producing your video. I like the simplicity of the Andersen hitch. Have you notice any wear of the chain links? I'm thinking of ordering one of these. I hate messing with the grease a and the weight of my E2.
It had zero issues and used it for a long time
I have a Ram with air suspension. Do you set it to normal ride height and put the suspension in jack mode when you connect the hitch?
Normal…
Rocky, I have been seeing people are saying not good for anything over 26 - 30 feet. How has it been with sway control?
Thanks
It works great.. just needs proper adjustment. I have a fifth wheel now but the hitch was always good for me
Thanks
I have a TT which is about 1K lighter than yours. I have used an Andersen with a 2500 Ram for 3 seasons and thousands of Rocky mountain miles. Works well with a proper truck like yours.
what constitutes a proper truck?
@@thefixer8457 A 3/4 ton truck for a camper over 26 feet of box length and/or over 6500 pounds
@@safrench I agree with pulling anything over 26 feet with a 3/4 ton. But, not the 6500 trailer weight. Many half ton trucks are rated for 10, 000 pounds or more. The weight of the trailer will not be the limiting factor for a 1/2 ton. Pay load will be exceeded long before you reach the max tow rating.
@@bobdrawbaugh4207 I will be installing my Andersen hitch on my TT and pulling it with my F-150. My TT is 26' box length and 6,800 lb gvwr with 800-900lb tongue weight (using my Sherline tongue scale). My truck is also my daily driver when I'm not traveling with the TT and I didn't want to have to drive a 3/4 truck (or pay for it) for the majority of the miles that it would be driven. I ordered my Supercab F-150 with the tow package and 18" wheels for towing. The very first thing I did when I got to the dealership to check out my truck was open the drivers door and check the sticker. This half ton truck has a payload of 2,175lbs and I will have a comfortable amount of payload remaining even if I load out the TT to its max. The truck has a tow capacity of 9,400 since it's a 4X4 and I didn't get the 373 gears. I know I'll probably have to listen to know-it-all's in my travels tell me that my truck is too light but I'll just open the door and point, then wish them a pleasant day.
How is it holding up? I just got mine. And frame dents from bolts brackets? Thanks
I just installed one of these last week for a new trailer using your video and the one from Andersen. I noticed some issues with your install and wondered if you went back to correct them and if you noticed any difference.
First issue was with the triangle plate. I see you insert the pin and then swivel it into position with your hands. If that plate can swivel that easily you have no sway control. Mine was similar, but followed the directions of using a piece of wood and mallet to knock the plate inline with the bumper. Did you ever fix that? What did you have to do?
Next noticed your installation of the trailer brackets were not done according to directions. Sounded like you measured the brackets at 29” instead of using the chain lengths. Mine came out at 28” at the top and 27.25” on the bottom. Which is another part of the install that differed. You installed the brackets straight up and down with the chains pointing to the ground. The installation calls for pulling the top back as far as possible and the chain on the bottom as parallel possible. Essential at an angle with the top further from the coupler. Did you ever go back and reinstall the brackets?
When the chains have tension it creates friction for sway control. Brackets have worked with zero issues.
So do you just loosen the chains to unhook?
according to those cat scale tickets , both times the rear axle outweighed the front axle by a few hundred pounds give or take...shouldnt the axles be the same or as close to the same ratio as trhey were when you weighed your truck alone? as it sits the front axle is still lighter than the rear so despite the heights of the wheel wellos being close to original im betting that front axle is still at least 300 pounds lighter than the rear making it imho iffy when it comes to stopping
No it’s not supposed to balance.. just shift a percentage of weight to front axle. Your payload rating is designed for the rear axle for the most part.
It’s not a ratio so much as putting the pounds back on the front axle. If your front end is 1
200lbs lighter you want to get as close to that as possible back on the front axle.
very informative bro !!!!!
Great video. Do you get any sway when you are passed by a big tractor-trailer? I currently use a Blue ox sway pro with a 30 ft trailer and a half ton F-150. Crosswinds usually don't affect it at all but when I am passed by a tractor-trailer it sways a lot. Sometimes I feel like I'm being sucked into the tractor-trailer's lane and then pushed off the road after it gets by me.
The sway is less than I had with bar hitch.. one thing to remember when passing trucks is have a little pull on trailer and going down hill. When trailer is pushing the truck it will sway with winds. I always make sure I’m accelerating slightly when trucks are beside me or when going downhill.. A lot of peeps will let off accelerator when trucks go around as it’s the natural feeling. Keep a little pull on it and it will help significantly with your current hitch also
Great video, are you able to open the tailgate while hooked up without interfering with the power jack?
Wasn’t the 4-turn tightening of the nut supposed to be done with the camper/trailer already sitting on the hitchball? I was basing this observation from the official Anderson Hitches video. Im getting one tomorrow and wanted to make sure I do it right or not put too much tension on the chains. Great video by the way!
Easy to get chains at correct length with weight off.
How do you like your styker? I just bought a 2913 was wondering how it pulls, haven't picked it up yet. I have a chevy 3/4 ton HD
Pulls great.. I took it to Florida last year..
@@RockyRohde good to hear ! Can’t wait to pick mine up Saturday.. what model is yours?
I had the 2916 and lots of videos on my channel. Picked up a 44 ft toy hauler
Did you try towing without the WDH? How does it compare?
Are you still using the anderson hitch and liking it? I have a stryker 2912 and using husky now. Looking to have less bounce after crossing bridges and such. Thank you
Yes still using it…
I have a Ram 3500 Limited I think you have a 2500 and coil springs. does yours have air ride? I have a 22ft enclosed trailer that I use for tool trailer I am a mobile Heavy equipment mechanic. Just bought haven't received yet same WD. I have 1400lbs of tongue weight. and live in Florida make multiple trips to our place in NC, trailer pulls ok but feels funny sometimes ,hoping that this make a difference, being a heavy truck with air ride will only drop a 1" but I get weird messages and warnings say air ride will not function properly, cannot adjust, but it's already up, when I first pulled I didn't have a tongue scale now I do, but Cat scaled it and had 1600lbs. Top of ball was actually worn. I had a big 72" Snap On tool box across the front full, was just to much weight..Box weighs 1200lbs empty. Anyway swapped it out to a Harbor freight 42" and removed a lot of my tools. The trailer was custom built "V" slant nose,12"OC floor cross members and 7000lb torsion spread axles, and a 7000lb ramp door, with 7'6" height. so wondering if this will help any on a HD truck? I see you have a big truck I race here a mega truck or Hill in Hole Jeep for a few years. hence my name Joker Jeep.
Just wondering how did you lose 40lbs from your gross. the two cat scales?
Rocky, you still using this? how is it holding up, 1 yr later?
I have an e2 WDH setup from FastWay. But it is super heavy. I tow with an Audi Q7, and any unnecessary weight I can shed would be awesome.
Very well done explanation and walkthrough on the install and setup. Thanks for this. Subbed!
I have a large fifth wheel now.. I still recommend the Andersen. We pulled the trailer on a few 1200 mile trips.. it’s a good gitch
How do you secure your TT with this Anderson WDH still attached - or can you? Seems like that yoke provides an open invitation to thieves.
can you tell me what the measurement is from center of the ball back to the bracket that attaches to the trailer?
I adjusted to my chain length.. here is installation procedure
download2271.mediafire.com/tf1c7iiuv9kg/bx5xm3p7hie6515/3932+-+WD+Hitch+installation+manual+2022-Low+Res.pdf
It’s whatever you want it to be. You can take off (I think) up to 4 links or add as much chain as you need, within reason.
Just curious how you still like the Andersen hitch after having a few months? Anything change in your opinions on it?
Love it.. would never go back to a bar hitch… fixing to go from Florida to Texas with toy hauler next week. Trailer pulls amazing with it..
@@RockyRohde great to hear! I read some reviews that it wasn't for a long and heavy trailer but your review helped keep me with it. Just ordered it!
@@laker42 you won’t regret it.. My Toy hauler is 36’ and I load my lifted canam max XMR in the back…. It weighs 2700 pounds. Pulls like nothing is behind me.. plus no more popping and creaking..
When you loaded your ATV did you have to adjust the WDH? Thanks in advance.
I didnt
I am using the Equlizer 4 hitch on our Ram 2500 and Flagstaff RV. It weighs 7600 unloaded with a hitch weight of 963. The camper is 35' .The Eq does ok, but the weight and grease is getting to me. Is the Anderson a real upgrade rom my Eq 4?
I think my Andersen pulls better.. plus I can remove it with one hand and hook it without dealing with bars
just removed my Equilizer 4 hitch today. Its hitting my trailer and cutting my safety chains. Looking at this design as replacement.
How did you loosen the chains at the scale? With the big socket? If so, HOW do you know how much to tighten it again, unless you start over and count 4 revolutions I don't see how you'll know. And is 4 revolutions AFTER hand tightening or..? Sorry, I'm a girl. 😅
It's not always so easy to get that triangle plate off even raising the jack pad up to loosen tension, once I have it all setup, I measured the distance from the washer behind the nut to tip or end of the thread, I used an old credit card or any plastic card because it's easy to cut . and cut the card in an L shape and made it into a depth gauge, so whenever I need to loosen a few threads to get the plate off, I just re tighten it and use the cutout credit card to make sure it's the right length. This works on both sides
Great video. I have this hitch and I have struggled so much with figuring it out because I also have the air suspension. Quick question: when you do all your measuring and setup, do you have to turn the suspension off and put it in tire jack mode?
Here is how I setup my tension. I hook it up to trailer and let air suspension adjust. Then I raise it with the jack about 2-3 inches and snug chains by hand. Then I drop the weight back on vehicle. You will notice chains are tight and should be good to go!!
So technically.. was your drive axel overloaded without that hitch engaged? I have a 19 ram 2500.. my axel rating is 6000lbs. I'm assuming yours is similar?
My cat scale results are terrible. Only 20 lbs distributed to front axle and 40 lbs to trailer axle. How are you getting 200 lbs…???
Thank you for the time you put in this review. We are first time Travel Trailer owners( still on order) in our 70’s. Towing was one of the biggest stressors that had talked us out of the RV life for the last 4 years. We finally said, WTH, we’ll never know unless we try. You took a lot of the anxiety out of this process with this video. The weight aspect had a big factor with us choosing this hitch. After a few months, anything new to add? Thanks again. Larry
Pulls great and is lightweight.. you won’t be disappointed.
Well I do have a question. Sort of confused me. You said you measured to the height of the coupler and got 10.” And the ball needs to be 1 1/2” taller. That’s where I’m lost. For everything to be level it would seem that the top of the ball should be the same as the top of the coupler?
Thank you.
You want the trailer to sit almost level with truck. Most trucks will drop 1” to 1.5” with weight. For initial setup for ball height hook it to truck and adjust it up or down to find the closest to level. Once you have that add the chains and tension.
@@larrymccorkle3409 he threw me off with that too, but he meant 1ft 10in. He repeated it when he measured the truck side and said '1ft...10.." that when I caught on to his measurements. Great video!
I don’t think you’re supposed to be able to move that triangle plate so easily like that. Right around 9:00. They’re supposed to be pressed on.
How have you liked your Stryker trailer? Quality good? Would you buy it again? Do you have any issues with the width of your Can Am when loading it into you trailer? Do you drive it straight in or do you back it in?
I am currently at Disney ft wilderness in Florida. Trailer pulls great and I really like that it has shocks on the axles. Just traveled 1200 miles and carried golf cart with us. Quality in build is good for me.. I have had a 44 voltage fifth wheel and it is about the same. Stryker offers a really good toy hauler with larger tanks and good floor plans. I like a 16ft garage, large King bed with room to walk around it, and a large bathroom.. I also like that I don’t have to stop at truck stops to get fuel. I have been camping for over 20 years and not interested in any other trailer. If you have a dealer close go check one out. Sure if I didn’t want a toy hauler I would prob have something else.. this one just checks all the boxes for me. My canam defender XMR max 6 passenger fits with 30” boggers on 15x7 wheels. It fits forward and backwards. Keep offset close.
@@RockyRohde Great video and thanks so much for the reply!!
Rocky : Well presented. I'm in the same boat as yourself : Getting a new trailer & tired of lifting the heavy old hitch & bars. My only concern is most of the youtube's the people had pretty light or small trailers. Mine is about 8500#'s wet. Now that you have had yours for a time, has your opinion changed? does it take the sway out any different than old set up? You showed the 4 turns on the 'port' side; did you do the same on the 'starboard' side as well and just not record it?
Just pulled my trailer from Texas to Florida. It was 1092 miles each way with golf cart in trailer. Pulled like a dream. I absolutely recommend as it is so easy to hookup. The sway control is as good as other hitches. When I hook the trailer up I latch it and lift truck about 4-5” from being able to latch hitch. Then I hand tighten each side to remove slack and I let trailer down. The chains are extremely tight and pulls well for me. I don’t really use the socket and wrench. I let the jacket do the work same as a bar hitch. The hitch is very quiet and I love the fact I can remove it without killing my back. My days are done with bar hitches. You will have zero regret with the Andersen. Most that have anything bad to say about it don’t own it…
2 questions: with th 8" drop you are all set for a truck with a lift kit? also how do you know what size bracket do you need...that sheet shows different bracket size for the 10k gtwr...please help.
I ordered the 2.5 shank from Andersen. 8” should be good for a leveled to 3.5” lift truck with 35” tires. If you are stock with no level kit prob need a 5”.. I ordered the larger drop and if it was to much I could just cut it off..
Is this guy 4 foot tall?
Another reason a 5th wheel is far better than bumperpull. Can throw another trailer behind 5th wheel if want for toys to.
Depends what your looking for.. my voltage 4250 fifth does not have a 16 ft garage.. does not fit under a lot of trees, and requires truck stops.. My defender Max 6 passenger XMR lifted with 30’s fits in the Stryker.. it also has shocks on the axles.. been camping 20 years really like this over the fifth.. easier to hookup and pull.. it’s all about what you want
100 yrd tape? Man a 48 inch measuring stick would have made things much easier and way more accurate.
I had an Equalizer hitch and greasing the bars were not in the instructions. I think that's where the friction helps to reduce sway.
With that said, I do appreciate the video. You definitely demonstrated just how light the Anderson hitch really is.
Thanks!! Yeah tape measures and 10mm sockets are hiding in the same place..
Hey, Rocky what kind of mechanic are you? My son is interested in becoming a mechanic or something similar but I don't know anything about tradework so I have a hard time helping him decide what to do
I started in the oilfield when I was 16 worked on mud pumps, Diesel engines, and Rig electric and instrumentation. In my early 20’s I decided to get into compression and natural gas engines.. Big accesable engines that were clean instead of knuckle busting compartment engines. Worked mostly on cat engines on compressors 3606, 3608, 3516, 33 series engines. If he is interested in cleaner engine work and good pay check out compression.
I'm giggling because you left so much slack in the tape measure when measuring wheel fender height on the rear the second time.
I’m going send you a 10’ tape
I purchased 10 last week… they will disappear within a month lol
Go to the Andersen’s UA-cam Install vid for Torque Specifications: ua-cam.com/video/QXScZUEVcrc/v-deo.htmlsi=2hEza3QNyAeJuvVM
I don't see how the sway control works. With the equalizer you used to have the friction makes since. With this I just don't see it.
Also how does it do backing up on sharp, almost jack knifed, angles? Seems like it'll split those bushings?
They are urethane bushings they will not split.
I can see how the sway part works what I can get my mind wrapped around is how the WD works without stiff bars pulling up cant see how chains can do the same as a stiff bar
The hitch ball stem is press fit into a urethane cone, the more weight on the ball the tighter it holds. The fin at the bottom is connected to the ball stem and the chains pull against that tension.
The tension on the urethane bushings never changes once you set it by the number of turns on the nuts. This hitch handles turns when backing up very well. The pivot happens in the tapered ball stem turning inside the alloy housing, which is seated into a polymer friction sleeve. It is that friction which controls any tendency to sway. As the above post states, the more weight on the ball, the more friction there is, with a corresponding increase in sway resistance. The weight transfer is handled by the chain tension pulling on the yoke on the bottom of the ball stem.
I had a 2019 Tundra 1794 and a Lance 2465.
Total Rig 13970 lbs
Trailer only 6468
Truck only 6600
Tongue Wt 902
The payload is 1185 lbs. As you can see a max trailer weight of 9100lbs means nothing, as a tongue weight of 902 from payload of 1185 leaves nothing for people and supplies in the truck. I tried towing, but it wasn’t very good.
I switched to a 2022 F350 with a 3700 lbs payload and max trailer of 15000 lbs.
So, everything well within capacity.
However, I could not get the trailer to stop swaying. Anything more than 60 mph, bad sway. Going downhill even worse.
I tried everything with the Andersen hitch, adjusted height, chain tensions, reload weight, etc. It just would not stop swaying at more than 60 mph or downhills greater than 50 mph.
I switched to a trunion bar hitch (Weighsafe) and have zero sway.
Im extremely disappointed in Andersen hitch and would ver recommend it in a trailer more than 2000-3000 lbs.
I couldn't resist I have to make this comment. You need a bigger tape measure !
Yeah I know.. I looked all over my shop for 30 mins and couldn’t find it. 5 mins after video it was sitting on my work bench 😂
You could have measured from the ceiling down 😂
Are you still happy with it ? I hear people with larger trailers like yours that aren't impressed? Great video
Flipflops no bueno!!!!!
Toes are expendable lol